- Mega2560 support has been moved to the Grbl-Mega
[project](http://github.com/gnea/grbl-Mega/) to clean up the code and
make future developments easier with increased flash and RAM. All new
developments between the 328p and Mega2560 will be synced when it makes
sense to.
- OEM single file compile configuration option. Before OEMs needed to
alter three files. Provided a way to just alter the config.h file to
contain everything for a particular Grbl build. See config.h for more
details.
- Removed defaults and cpu_map directories and reverted back to
defaults.h and cpu_map.h to contain all definitions. This should help
reduce some headaches and the previous implementation inadvertently
created. Also, it makes the single file config.h possible.
- Moved (and tweaked) the invert control pin mask define and placed
into config.h, rather than in the cpu_map.h file. Makes more sense
there.
- Soft limit errors were stuck in a feed hold without notifying the
user why it was in a hold. When resumed, the soft limit error would
kick in. Issue should be fixed to behave as intended to automatically
hold and issue a soft limit alarm once the machine has come to a stop.
- Soft limit errors were stuck in a feed hold without notifying the
user why it was in a hold. When resumed, the soft limit error would
kick in. Issue should be fixed to behave as intended. To automatically
hold and issue a soft limit alarm once the machine has come to a stop.
- Planner was under-estimating maximum speeds through straight
junctions in certain cases. The calculations have been updated to be
more accurate.
- Strange sizeof() bug in the most recent releases. Manifested as an
alarm upon a power up even when homing was disabled. Fixed by declaring
sizeof() with struct types, rather than variable names, even though
they were validated to give the same value.
- Spindle speed zero should disable the spindle. Now fixed.
- New configuration option for inverting certain limit pins. Handy for
mixed NO and NC switch machines. See config.h for details.
- New pin state realtime reporting feature. Instead of `Lim:000` for
limit state reports, the new feature shows `Pin:000|0|0000`, or
something similar. The `|` delimited fields indicate xyz limits, probe,
and control pin states, where 0 is always not triggered, and 1 is
triggered. Invert masks ARE accounted for.
Each field may be enabled or disabled via the `$10` status report
setting. The probe and control pin flags are bits 5 and 6, respectively.
- Remove the now deprecated `REPORT_CONTROL_PIN_STATE` option in
config.h
- The old limit pin reports `Lim:000` may be re-enabled by commenting
out `REPORT_ALL_PIN_STATES` in config.h.
- Incremented the version letter (v1.0c) to indicate the change in
reporting style.
- Replaced all bit_true_atomic and bit_false_atomic macros with
function calls. This saved a couple hundred bytes of flash.
- G38.x was not printing correctly in the $G g-code state reports. Now
fixed.
- When investigating the above issue, it was noticed that G38.x
wouldn’t show at all, but instead a G0 would be printed. This was
unlike the v0.9j master build. It turned out volatile variables do not
like to be defined inside a C struct. These are undefined on how to be
handled. Once pulled out, all weird issues went away.
- Also changed two ‘sizeof()’ statements in the mc_probe() and
probe_state_monitor() functions to be more robust later on.
- Updated the commit logs to individual files for each minor release.
Forgot to update the generating script to account for this.
- G38.x was not printing correctly in the $G g-code state reports. Now
fixed.
- Potential bug regarding volatile variables inside a struct. It has
never been a problem in v0.9, but ran into this during v1.0
development. Just to be safe, the fixes are applied here.
- Updated pre-built firmwares with these two bug fixes.
- G28 and G30’s behavior has been updated from the old NIST g-code
standard to LinuxCNC’s. Previously when an intermediate motion was
programmed, the NIST standard would move all axes to the final G28/30
stored coordinates. LinuxCNC states it only moves the axes specified in
the command.
For example, suppose G28’s stored position is (x,y,z) = (1,2,3) for
simplicity, and we want to do an automated z-axis tool retraction and
then park at the x,y location. `G28 G91 Z5` will first move the Z axis
5mm(or inches) up, then move Z to position 3 in machine coordinates.
Next, the command `G28 G91 X0 Y0` would skip the intermediate move
since distance is zero, but then move only the x and y axes to machine
coordinates 1 and 2, respectively. The z-axis wouldn’t move in this
case, since it wasn’t specified.
This change is intended to make Grbl more LinuxCNC compatible while
making commands, like the shown tool retraction, much easier to
implement.
- Tons of new stuff in this release, which is fairly stable and well
tested. However, much more is coming soon!
- Real-time parking motion with safety door. When this compile option
is enabled, an opened safety door will cause Grbl to automatically feed
hold, retract, de-energize the spindle/coolant, and parks near Z max.
After the door is closed and resume is commanded, this reverses and the
program continues as if nothing happened. This is also highly
configurable. See config.h for details.
- New spindle max and min rpm ‘$’ settings! This has been requested
often. Grbl will output 5V when commanded to turn on the spindle at its
max rpm, and 0.02V with min rpm. The voltage and the rpm range are
linear to each other. This should help users tweak their settings to
get close to true rpm’s.
- If the new max rpm ‘$’ setting is set = 0 or less than min rpm, the
spindle speed PWM pin will act like a regular on/off spindle enable
pin. On pin D11.
- BEWARE: Your old EEPROM settings will be wiped! The new spindle rpm
settings require a new settings version, so Grbl will automatically
wipe and restore the EEPROM with the new defaults.
- Control pin can now be inverted individually with a
CONTROL_INVERT_MASK in the cpu_map header file. Not typical for users
to need this, but handy to have.
- Fixed bug when Grbl receive too many characters in a line and
overflows. Previously it would respond with an error per overflow
character and another acknowledge upon an EOL character. This broke the
streaming protocol. Now fixed to only respond with an error after an
EOL character.
- Fixed a bug with the safety door during an ALARM mode. You now can’t
home or unlock the axes until the safety door has been closed. This is
for safety reasons (obviously.)
- Tweaked some the Mega2560 cpu_map settings . Increased segment buffer
size and fixed the spindle PWM settings to output at a higher PWM
frequency.
- Generalized the delay function used by G4 delay for use by parking
motion. Allows non-blocking status reports and real-time control during
re-energizing of the spindle and coolant.
- Added spindle rpm max and min defaults to default.h files.
- Added a new print float for rpm values.
- Version bump requested by OEMs to easily determine whether the
firmware supports the new EEPROM reset feature. Other than that, no
significant changes.
- Tweaked the previous EEPROM restore implementation and added new
functionality.
- `$RST=$` restores the `$$` grbl settings back to firmware defaults,
which are set when compiled.
- `$RST=#` restores the `$#` parameters in EEPROM. At times it’s useful
to clear these and start over, rather than manually writing each entry.
-`$RST=*` wipe all of the data in EEPROM that Grbl uses and restores
them to defaults. This includes `$$` settings, `$#` parameters, `$N`
startup lines, and `$i` build info string.
NOTE: This doesn’t write zeros throughout the EEPROM. It only writes
where Grbl looks for data. For a complete wipe, please use the Arduino
IDE’s EEPROM clear example.
- Refactored the restore and wipe functions in settings.c to
accommodate the new commands.
- New restore setting defaults command. Only wipes ‘$$’ setting in
EEPROM and reloads them based on the defaults used when Grbl was
compiled. Used with a `$RST` command
NOTE: `$RST` is intentionally not listed in the Grbl ‘$’ help message.
- Added X-Carve 500mm and 1000mm default files.
- Tweaked all default files. Removed obsolete AUTO_START and updated
some JUNCTION_DEVIATION defaults after testing showed these needed to
be reduced slightly.
- Updated new homing cycle to error out when a pull-off motion detects
the limit is still active.
- Created a limits_get_state() function to centralize it. It reports
state as a bit-wise booleans according to axis numbering.
- Updated the print uint8 functions. Generalized it to allow both base2
and base10 printouts, while allowing base2 prints with N_AXIS digits
for limit state status reports. Doing this saved about 100bytes of
flash as well.
- Applied CoreXY status reporting bug fix by @phd0. Thanks!
- Critical fix for M0 program pause. Due to its recent change, it would
cause Grbl to suspend but wouldn’t notify the user of why Grbl was not
doing anything. The state would show IDLE and a cycle start would
resume it. Grbl now enters a HOLD state to better indicate the state
change.
- Critical fix for M2 and M30 program end. As with M0, the state
previously would show IDLE while suspended. Grbl now does not suspend
upon program end and leaves job control to the GUI. Grbl simply reports
a `[Pgm End]` as a feedback message and resets certain g-code modes.
- M2/30 g-code reseting fix. Previously Grbl would soft-reset after an
M2/30, but this was not complaint to the (linuxcnc) g-code standard. It
simply resets [G1,G17,G90,G94,G40,G54,M5,M9,M48] and keeps all other
modes the same.
- M0/M2/M30 check-mode fix. It now does not suspend the machine during
check-mode.
- Minor bug fix related to commands similar to G90.1, but not G90.1,
not reporting an unsupported command.
- Homing cycle refactoring. To help reduce the chance of users
misunderstanding their limit switch wiring, Grbl only moves a short
distance for the locate cycles only. In addition, the homing cycle
pulls-off the limit switch by the pull-off distance to re-engage and
locate home. This should improve its accuracy.
- HOMING_FORCE_ORIGIN now sets the origin to the pull-off location,
rather than where the limit switch was triggered.
- Updated default junction deviation to 0.01mm. Recent tests showed
that this improves Grbl’s cornering behavior a bit.
- Added the ShapeOko3 defaults.
- Added new feedback message `[Pgm End]` for M2/30 notification.
- Limit pin reporting is now a $10 status report option. Requested by
OEMs to help simplify support troubleshooting.
- Commit history added to repo, as an easier way for people to see view
the changes over time.
- Grbl logo copyright license added. All rights reserved with regards
to the Grbl logo.
- G2/3 full circles would sometime not execute. The problem was due to
numerical round-off of a trig calculation. Added a machine epsilon
define to help detect and correct for this problem. Tested and should
not effect general operation of arcs.
- Apparently inverse time motion were not working for quite some time.
Goes to show how many people actually use it. The calculation was bad
and is now fixed in this update. It should now work correctly.
- `;` comment type is now supported. This is standard on LinuxCNC and
common on 3d printers. It was previously not supported due to not
existing in the NIST standard, which is out-dated.
- New compile-option to ECHO the line received. This should help users
experiencing very weird problems and help diagnose if there is
something amiss in the communication to Grbl.
- New compile-option to use the spindle direction pin D13 as a spindle
enable pin with PWM spindle speed on D11. This feature has been
requested often from the laser cutter community. Since spindle
direction isn’t really of much use, it seemed like good good trade.
Note that M4 spindle enable counter-clock-wise support is removed for
obvious reasons, while M3 and M5 still work.
- Cleaned up the limit pin state reporting option to display only the
state per axis, rather than the whole port. It’s organized by an XYZ
order, 0(low)-1(high), and generally looks like `Lim:001`.
- Separated the control pin state reporting from limit state reporting
as a new compile option. This stayed the same in terms of showing the
entire port in binary, since it’s not anticipated that this will be
used much, if at all.
- Updated some of the gcode source comments regarding supported g-codes.
- The homing cycle should be working again. Reverted it back to how it
was about a month ago before I started to fiddle with it. Turns out
that my past self knew what he was doing.
- Added an include in the right spot, if a user tries to compile and
upload Grbl through the Arduino IDE with the old way.
- Fixed a minor bug with homing max travel calculations. It was causing
simultaneous axes homing to move slow than it did before.
- G91.1 support added. This g-code sets the arc IJK distance mode to
incremental, which is the default already. This simply helps reduce
parsing errors with certain CAM programs that output this command.
- Max step rate checks weren’t being compiled in if the option was
enabled. Fixed now.
- Alarm codes were not displaying correctly when GUI reporting mode was
enabled. Due to unsigned int problem. Changed codes to positive values
since they aren’t shared with other codes.
- New configuration option at compile-time:
- Force alarm upon power-up or hard reset. When homing is enabled,
this is already the default behavior. This simply forces this all of
the time.
- GUI reporting mode. Removes most human-readable strings that GUIs
don’t need. This saves nearly 2KB in flash space that can be used for
other features.
- Hard limit force state check: In the hard limit pin change ISR, Grbl
by default sets the hard limit alarm upon any pin change to guarantee
the alarm is set. If this option is set, it’ll check the state within
the ISR, but can’t guarantee the pin will be read correctly if the
switch is bouncing. This option makes hard limit behavior a little less
annoying if you have a good buffered switch circuit that removes
bouncing and electronic noise.
- Software debounce bug fix. It was reading the pin incorrectly for the
setting.
- Re-factored some of the ‘$’ settings code.
- Instead of a single overall max travel for a search distance for the
homing limit switches. The homing cycle now applies the max travel of
each axis to the search target. Generally makes more sense this way and
saved more than a 100bytes of flash too.
- Homing cycle failure reports alarm feedback when the homing cycle is
exited via a reset, interrupted by a safety door switch, or does not
find the limit switch.
- Homing cycle bug fix when not finding the limit switch. It would just
idle before, but now will exit with an alarm.
- Licensing update. Corrected licensing according to lawyer
recommendations. Removed references to other Grbl versions.
- Overhauled the state machine and cleaned up its overall operation.
This involved creating a new ‘suspend’ state for what all external
commands, except real-time commands, are ignored. All hold type states
enter this suspend state.
- Removed ‘auto cycle start’ setting from Grbl. This was not used by
users in its intended way and is somewhat redundant, as GUI manage the
cycle start by streaming. It also muddled up how Grbl should interpret
how and when to execute a g-code block. Removing it made everything
much much simpler.
- Fixed a program pause bug when used with other buffer_sync commands.
- New safety door feature for OEMs. Immediately forces a feed hold and
then de-energizes the machine. Resuming is blocked until the door is
closed. When it is, it re-energizes the system and then resumes on the
normal toolpath.
- Safety door input pin is optional and uses the feed hold pin on A1.
Enabled by config.h define.
- Spindle and coolant re-energizing upon a safety door resume has a
programmable delay time to allow for complete spin up to rpm and
turning on the coolant before resuming motion.
- Safety door-style feed holds can be used instead of regular feed hold
(doesn’t de-energize the machine) with a ‘@‘ character. If the safety
door input pin is not enabled, the system can be resumed at any time.
- Re-organized source code files into a ‘grbl’ directory to lessen one
step in compiling Grbl through the Arduino IDE.
- Added an ‘examples’ directory with an upload .INO sketch to further
simplify compiling and uploading Grbl via the Arduino IDE.
- Updated the Makefile with regard to the source code no longer being
in the root directory. All files generated by compiling is placed in a
separate ‘build’ directory to keep things tidy. The makefile should
operate in the same way as it did before.
