Removed inline from all functions.
If this is really needed is there another way that we can get
around using it? (The Arduino IDE does not recognize it)
- Changed up mc_line to accept an array rather than individual x,y,z
coordinates. Makes some of the position data handling more effective,
especially for a 4th-axis later on.
- Changed up some soft limits variable names.
These changes include a path separator fix and the removal of --gc-sections which causes ld failures, and is not needed on a pc.
This patch also changes how a compiler is selected. The makefile will now select the system compiler , which should work fine
under mingw and linux.
- Returned the max step rate to 30kHz. The new arc algorithm works uses
so much less CPU overhead, because the segments are longer, that the
planner has no problem computing through them.
- Fixed an issue with the acceleration independence scaling. Should now
work with accelerations above 400mm/sec^2 or so.
- Updated README
- Arc mm_per_segment parameter was removed and replaced with an
arc_tolerance parameter, which scales all arc segments automatically to
radius, such that the line segment error doesn't exceed the tolerance.
Significantly improves arc performance through larger radius arc,
because the segments are much longer and the planner buffer has more to
work with.
- Moved n_arc correction from the settings to config.h. Mathematically
this doesn't need to be a setting anymore, as the default config value
will work for all known CNC applications. The error does not accumulate
as much anymore, since the small angle approximation used by the arc
generation has been updated to a third-order approximation and how the
line segment length scale with radius and tolerance now. Left in
config.h for extraneous circumstances.
- Corrected the st.ramp_count variable (acceleration tick counter) to a
8-bit vs. 32-bit variable. Should make the stepper algorithm just a
touch faster overall.
- Fixed an issue (hopefully) with slow trailing steps after a
triangular velocity profile move. Sets the trapezoid tick cycle counter
to the correct value for an accurate reproduction of the deceleration
curve. Keeps it from arriving too early to the target position, which
causes the slow trailing steps.
- Added Zen Toolworks 7x7 to default settings.
- Updated readme with new edge build.
- Maximum velocity for each axis is now configurable in settings. All
rapids/seek move at these maximums. All feed rates(including rapids)
may be limited and scaled down so that no axis does not exceed their
limits.
- Moved around auto-cycle start. May change later, but mainly to ensure
the planner buffer is completely full before cycle starting a streaming
program. Otherwise it should auto-start when there is a break in the
serial stream.
- Reverted old block->max_entry_speed_sqr calculations. Feedrate
overrides not close to ready at all.
- Fixed intermittent slow trailing steps for some triangle velocity
profile moves. The acceleration tick counter updating was corrected to
be exact for that particular transition. Should be ok for normal
trapezoidal profiles.
- Fixed the Timer0 disable after a step pulse falling edge. Thanks
@blinkenlight!
NOTE: This push is a work-in-progress and there are known bugs that
need to be fixed, like homing acceleration being incompatible. Released
for testing. Settings will definitely be overwritten, as new settings
were needed.
- Acceleration independence installed in planner. Each axis can now
have different accelerations and Grbl will maximize the accelerations
depending on the direction its moving. Very useful for users like on
the ShapeOko with vastly different Z-axis properties.
- More planner optimizations and re-factoring. Slightly improved some
of the older calculations, but new acceleration calculations offset
these improvements. Overall no change in processing speed.
- Removed planner nominal length checks. It was arguable whether or not
this improved planner efficiency, especially in the worst case scenario
of arcs.
- Updated readme and changed to markdown format.
Because the Downloads section has been removed, added a builds folder
for users to download pre-compiled firmware without needing to compile
it themselves.
- Improved planner execution speed by 5% or more. Re-factored most of
the calculations in terms of the square of velocity. This removed a lot
of sqrt() calculations for every planner_recalculate.
- Oops again. Thought the new planner changes made things much better,
but there was a bug. Improvements we on the order of 20% execution time
reduction, rather than half. The increase to 30kHz Ranade timer
frequency also increased the overall overhead, so the total planner
change? Zero. But, it's still better.
