- Program stop support (M0,M1*,M2,M30*). *Optional stop to be done.
*Pallet shuttle not supported.
- Work position is set equal to machine position upon reset, as
according to NIST RS274-NGC guidelines. G92 is disabled.
- Renamed mc_set_current_position() to mc_set_coordinate_offset().
- Fixed bug in plan_synchronize(). Would exit right before last step is
finished and caused issues with program stops. Now fixed.
- Spindle now stops upon a run-time abort command.
- Updated readme and misc upkeeping.
- Fixed a premature step end bug dating back to Simen's 0.7b edge
version is fixed, from which this code is forked from. Caused by Timer2
constantly overflowing calling the Step Reset Interrupt every 128usec.
Now Timer2 is always disabled after a step end and should free up some
cycles for the main program. Could be more than one way to fix this
problem. I'm open to suggestions.
- _delay_ms() refactored to accept only constants to comply with
current compilers. square() removed since not available with some
compilers.
- Grbl now tracks both home and work (G92) coordinate systems and does
live updates when G92 is called.
- Rudimentary home and work position status reporting. Works but still
under major construction.
- Updated the main streaming script. Has a disabled periodic timer for
querying status reports, disabled only because the Python timer doesn't
consistently restart after the script exits. Add here only for user
testing.
- Fixed a bug to prevent an endless serial_write loop during status
reports.
- Refactored the planner variables to make it more clear what they are
and make it easier for clear them.
- Added machine position reporting to status queries. This will be
further developed with part positioning/offsets and maintaining
location upon reset.
- System variables refactored into a global struct for better
readability.
- Removed old obsolete Ruby streaming scripts. These were no longer
compatible. Updated Python streaming scripts.
- Fixed printFloat() and other printing functions.
- Decreased planner buffer back to 18 blocks and increased TX serial
buffer to 64 bytes. Need the memory space for future developments.
- Begun adding run-time modes to grbl, where block delete toggle, mm/in
reporting modes, jog modes, etc can be set during runtime. Will be
fleshed out and placed into EEPROM when everything is added.
- ALPHA status. - Multitasking ability with run-time command executions
for real-time control and feedback. - Decelerating feed hold and resume
during operation. - System abort/reset, which immediately kills all
movement and re-initializes grbl. - Re-structured grbl to easily allow
for new features: Status reporting, jogging, backlash compensation. (To
be completed in the following releases.) - Resized TX/RX serial buffers
(32/128 bytes) - Increased planner buffer size to 20 blocks. - Updated
documentation.
- Fleshed out the original idea to completely remove the long slope at
the end of deceleration issue. This third time should absolutely
eliminate it.
- Changed the acceleration setting to kept as mm/min^2 internally,
since this was creating unneccessary additional computation in the
planner. Human readable value kept at mm/sec^2.
- Updated grbl version 0.7d and settings version to 4. NOTE: Please
check settings after update. These may have changed, but shouldn't.
- Before updating the new features (pause, e-stop, federate override,
etc), the edge branch will soon be merged with the master, barring any
immediate issues that people may have, and the edge branch will be the
testing ground for the new grbl version 0.8.
- The long standing issue of a long slope at deceleration is likely
fixed. The stepper program was not tracking and timing the end of
acceleration and start of deceleration exactly and now is fixed to
start and stop on time. Also, to ensure a better acceleration curve fit
used by the planner, the stepper program delays the start of the
accelerations by a half trapezoid tick to employ the midpoint rule. -
Settings version 3 migration (not fully tested, but should work) -
Added a MINIMUM_PLANNER_SPEED user-defined parameter to planner to let
a user change this if problems arise for some reason. - Moved all
user-definable #define parameters into config.h with clear comments on
what they do and recommendations of how to change them. - Minor
housekeeping.
- Fixed the planner TODO regarding minimum nominal speeds. Re-arranged
calculations to be both more efficient and guaranteed to be greater
than zero. - Missed a parenthesis location on the rate_delta
calculation. Should fix a nearly in-perceptible issue with incorrect
acceleration ramping in diagonal directions. - Increased maximum dwell
time from 6.5sec to an 18hour max. A crazy amount more, but that's how
the math works out. - Converted the internal feedrate values to mm/min
only, as it was switching between mm/min to mm/sec and back to mm/min.
Also added a feedrate > 0 check in gcode.c. - Identified the long slope
at the end of rapid de/ac-celerations noted by stephanix. Problem with
the numerical integration truncation error between the exact solution
of estimate_acceleration_distance and how grbl actually performs the
acceleration ramps discretely. Increasing the
ACCELERATION_TICKS_PER_SECOND in config.h helps fix this problem.
Investigating further.
- Serial functions contained quite a few modulo operations that would
be executed with high frequency when streaming. AVR processors are very
slow when operating these. In one test on the Arduino forums, it showed
about a 15x slow down compared to a simple if-then statement. -
Clarified some variable names and types and comments.
- Update grbl version and settings version to automatically reset
eeprom. FYI, this will reset your grbl settings. - Saved
3*BLOCK_BUFFER_SIZE doubles in static memory by removing obsolete
variables: speed_x, speed_y, and speed_z. - Increased buffer size
conservatively to 18 from 16. (Probably can do 20). - Removed expensive!
modulo operator from block indexing function. Reduces significant
computational overhead. - Re-organized some sqrt() calls to be more
efficient during time critical planning cases, rather than non-time
critical. - Minor bug fix in planner max junction velocity logic. -
Simplified arc logic and removed need to multiply for CW or CCW
direction.
- Significant improvements in the planner. Removed or reordered
repetitive and expensive calculations by order of importance:
recalculating unchanged blocks, trig functions [sin(), cos(), tan()],
sqrt(), divides, and multiplications. Blocks long enough for nominal
speed to be guaranteed to be reached ignored by planner. Done by
introducing two uint8_t flags per block. Reduced computational overhead
by an order of magnitude. - Arc motion generation completely
re-written and optimized. Now runs with acceleration planner. Removed
all but one trig function (atan2) from initialization. Streamlined
computations. Segment target locations generated by vector
transformation and small angle approximation. Arc path correction
implemented for accumulated error of approximation and single precision
calculation of Arduino. Bug fix in message passing.
