b1ecb47bec
10 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
chamnit
|
e455764079 |
v1.1f. Parking override control. Spindle enable pin option.
[ver] v1.1f update due to tweaks to interface from new parking override control. [new] Parking motion override control via new `M56 P0` and `M56 P1` command, which disables and enables the parking motion, respectively. Requires ENABLE_PARKING_OVERRIDE_CONTROL and PARKING_ENABLE enabled in config.h. Primarily for OEMs. [new] `M56` appears in the $G report when enabled. [new] Five new build info identification letters. Some were missing and a couple are new. Updated the CSV and documentation to reflect these new items. [new] Spindle enable pin configuration option to alter its behavior based on how certain lasers work. By default, Grbl treats the enable pin separately and leaves it on when S is 0. The new option turns the enable pin on and off with S>0 and S=0. This only is in effect when a user enables the USE_SPINDLE_DIR_AS_ENABLE_PIN option. [fix] M4 is now allowed to work when USE_SPINDLE_DIR_AS_ENABLE_PIN is enabled. Previously this was blocked and was problematic for laser folks using M4. [fix] Properly declared system variables as extern. Not sure how that went unnoticed or why it worked up until now but it has. [fix] EXTREMELY RARE. When AMASS is intentionally disabled and sent a motion command that is _one step_ in length, Grbl would not actuate the step due to numerical round-off. Applied a fix to prevent the round-off issue. [fix] Added a compile-time check for AMASS settings to make sure that the numerical round-off issue doesn’t effect it. This would only happen if someone set AMASS max levels to zero. It does not effect AMASS with its current defaults. [fix] Wrapped the mc_parking_motion() function in an ifdef for porting purposes. [fix] Fixed an issue when in inverse time mode and G0’s would require a F word. This was not correct. [fix] Added a note in the defaults.h file that MAX_TRAVEL values must be positive. Some users were setting this negative and it was causing issues. |
||
Sonny Jeon
|
d21e06a201 |
v1.1b: Tweaked Bf reports, jogging doc, saved another 160 bytes, minor bug fixes
- Increment to v1.1b due to status report tweak. - Tweaked the buffer state status reports to show bytes and blocks available, rather than in use. This does not require knowing the buffer sizes beforehand. It’s implicit. - Also, since buffer states are not used by most devs (after inquiries), it is no longer enabled by default and a status mask option was added for this. - Fixed some typos and updated for the report tweak in the documentation. - Wrote a joystick implementation concept in the jogging markdown document. Outlines how to get a low-latency feel to a joystick (and other input devices). - Removed XON/XOFF support. It’s not used by anyone because of its inherent problems. Remains in older versions for reference. - Added a compile option on how to handle the probe position during a check mode. - Fixed a jogging bug. If G93 is the modal state before a jogging motion, the feed rate did not get calculated correctly. Fixed the issue. - Refactored some code to save another 160+ bytes. Included an improved float vector comparison macro and reducing a few large and repetitive function calls. - Fixed a probing bug (existing in v0.9 too) where the target positions were not set correct and error handling was improper. |
||
|
chamnit
|
12f48a008a |
Grbl v1.0e huge beta release. Overrides and new reporting.
- Feature: Realtime feed, rapid, and spindle speed overrides. These
alter the running machine state within tens of milliseconds!
- Feed override: 100%, +/-10%, +/-1% commands with values 1-200% of
programmed feed
- Rapid override: 100%, 50%, 25% rapid rate commands
- Spindle speed override: 100%, +/-10%, +/-1% commands with values
50-200% of programmed speed
- Override values have configurable limits and increments in
config.h.
- Feature: Realtime toggle overrides for spindle stop, flood coolant,
and optionally mist coolant
- Spindle stop: Enables and disables spindle during a feed hold.
Automatically restores last spindles state.
- Flood and mist coolant: Immediately toggles coolant state until
next toggle or g-code coolant command.
- Feature: Jogging mode! Incremental and absolute modes supported.
- Grbl accepts jogging-specific commands like $J=X100F50. An axis
word and feed rate are required. G20/21 and G90/G91 commands are
accepted.
- Jog motions can be canceled at any time by a feed hold `!`
command. The buffer is automatically flushed. (No resetting required).
- Jog motions do not alter the g-code parser state so GUIs don’t
have to track what they changed and correct it.
- Feature: Laser mode setting. Allows Grbl to execute continuous
motions with spindle speed and state changes.
- Feature: Significantly improved status reports. Overhauled to cram in
more meaningful data and still make it smaller on average.
- All available data is now sent by default, but does not appear if
it doesn’t change or is not active.
- Machine position(MPos) or work position(WPos) is reported but not
both at the same time. Instead, the work coordinate offsets (WCO)are
sent intermittently whenever it changes or refreshes after 10-30 status
reports. Position vectors are easily computed by WPos = MPos - WCO.
- All data has changed in some way. Details of changes are in the
markdown documents and wiki.
- Feature: 16 new realtime commands to control overrides. All in
extended-ASCII character space.
- While they are not easily typeable and requires a GUI, they can’t
be accidentally triggered by some latent character in the g-code
program and have tons of room for expansion.
- Feature: New substates for HOLD and SAFETY DOOR. A `:x` is appended
to the state, where `x` is an integer and indicates a substate.
- For example, each integer of a door state describes in what phase
the machine is in during parking. Substates are detailed in the
documentation.
- Feature: With the alarm codes, homing and probe alarms have been
expanded with more codes to provide more exact feedback on what caused
the alarm.
- Feature: New hard limit check upon power-up or reset. If detected, a
feedback message to check the limit switches sent immediately after the
welcome message.
- May be disabled in config.h.
- OEM feature: Enable/disable `$RST=` individual commands based on
desired behavior in config.h.
- OEM feature: Configurable EEPROM wipe to prevent certain data from
being deleted during firmware upgrade to a new settings version or
`RST=*` command.
- OEM feature: Enable/disable the `$I=` build info write string with
external EEPROM write example sketch.
- This prevents a user from altering the build info string in
EEPROM. This requires the vendor to write the string to EEPROM via
external means. An Arduino example sketch is provided to accomplish
this. This would be useful for contain product data that is
retrievable.
- Tweak: All feedback has been drastically trimmed to free up flash
space for the v1.0 release.
- The `$` help message is just one string, listing available
commands.
- The `$$` settings printout no longer includes descriptions. Only
the setting values. (Sorry it’s this or remove overrides!)
- Grbl `error:` and `ALARM:` responses now only contain codes. No
descriptions. All codes are explained in documentation.
- Grbl’s old feedback style may be restored via a config.h, but
keep in mind that it will likely not fit into the Arduino’s flash space.
- Tweak: Grbl now forces a buffer sync or stop motion whenever a g-code
command needs to update and write a value to EEPROM or changes the work
coordinate offset.
- This addresses two old issues in all prior Grbl versions. First,
an EEPROM write requires interrupts to be disabled, including stepper
and serial comm. Steps can be lost and data can be corrupted. Second,
the work position may not be correlated to the actual machine position,
since machine position is derived from the actual current execution
state, while work position is based on the g-code parser offset state.
They are usually not in sync and the parser state is several motions
behind. This forced sync ensures work and machine positions are always
correct.
- This behavior can be disabled through a config.h option, but it’s
not recommended to do so.
- Tweak: To make status reports standardized, users can no longer
change what is reported via status report mask, except for only
toggling machine or work positions.
- All other data fields are included in the report and can only be
disabled through the config.h file. It’s not recommended to alter this,
because GUIs will be expecting this data to be present and may not be
compatible.
- Tweak: Homing cycle and parking motion no longer report a negative
line number in a status report. These will now not report a line number
at all.
- Tweak: New `[Restoring spindle]` message when restoring from a
spindle stop override. Provides feedback what Grbl is doing while the
spindle is powering up and a 4.0 second delay is enforced.
- Tweak: Override values are reset to 100% upon M2/30. This behavior
can be disabled in config.h
- Tweak: The planner buffer size has been reduced from 18 to 16 to free
up RAM for tracking and controlling overrides.
- Tweak: TX buffer size has been increased from 64 to 90 bytes to
improve status reporting and overall performance.
- Tweak: Removed the MOTION CANCEL state. It was redundant and didn’t
affect Grbl’s overall operation by doing so.
- Tweak: Grbl’s serial buffer increased by +1 internally, such that 128
bytes means 128, not 127 due to the ring buffer implementation. Long
overdue.
- Tweak: Altered sys.alarm variable to be set by alarm codes, rather
than bit flags. Simplified how it worked overall.
- Tweak: Planner buffer and serial RX buffer usage has been combined in
the status reports.
- Tweak: Pin state reporting has been refactored to report only the
pins “triggered” and nothing when not “triggered”.
- Tweak: Current machine rate or speed is now included in every report.
- Tweak: The work coordinate offset (WCO) and override states only need
to be refreshed intermittently or reported when they change. The
refresh rates may be altered for each in the config.h file with
different idle and busy rates to lessen Grbl’s load during a job.
- Tweak: For temporary compatibility to existing GUIs until they are
updated, an option to revert back to the old style status reports is
available in config.h, but not recommended for long term use.
- Tweak: Removed old limit pin state reporting option from config.h in
lieu of new status report that includes them.
- Tweak: Updated the defaults.h file to include laser mode, altered
status report mask, and fix an issue with a missing invert probe pin
default.
- Refactor: Changed how planner line data is generated and passed to
the planner and onto the step generator. By making it a struct
variable, this saved significant flash space.
- Refactor: Major re-factoring of the planner to incorporate override
values and allow for re-calculations fast enough to immediately take
effect during operation. No small feat.
- Refactor: Re-factored the step segment generator for re-computing new
override states.
- Refactor: Re-factored spindle_control.c to accommodate the spindle
speed overrides and laser mode.
- Refactor: Re-factored parts of the codebase for a new jogging mode.
Still under development though and slated to be part of the official
v1.0 release. Hang tight.
- Refactor: Created functions for computing a unit vector and value
limiting based on axis maximums to free up more flash.
- Refactor: The spindle PWM is now set directly inside of the stepper
ISR as it loads new step segments.
- Refactor: Moved machine travel checks out of soft limits function
into its own since jogging uses this too.
- Refactor: Removed coolant_stop() and combined with
coolant_set_state().
- Refactor: The serial RX ISR forks off extended ASCII values to
quickly assess the new override realtime commands.
- Refactor: Altered some names of the step control flags.
- Refactor: Improved efficiency of the serial RX get buffer count
function.
- Refactor: Saved significant flash by removing and combining print
functions. Namely the uint8 base10 and base2 functions.
- Refactor: Moved the probe state check in the main stepper ISR to
improve its efficiency.
- Refactor: Single character printPgmStrings() went converted to direct
serial_write() commands to save significant flash space.
- Documentation: Detailed Markdown documents on error codes, alarm
codes, messages, new real-time commands, new status reports, and how
jogging works. More to come later and will be posted on the Wiki as
well.
- Documentation: CSV files for quick importing of Grbl error and alarm
codes.
- Bug Fix: Applied v0.9 master fixes to CoreXY homing.
- Bug Fix: The print float function would cause Grbl to crash if a
value was 1e6 or greater. Increased the buffer by 3 bytes to help
prevent this in the future.
- Bug Fix: Build info and startup string EEPROM restoring was not
writing the checksum value.
- Bug Fix: Corrected an issue with safety door restoring the proper
spindle and coolant state. It worked before, but breaks with laser mode
that can continually change spindle state per planner block.
- Bug Fix: Move system position and probe position arrays out of the
system_t struct. Ran into some compiling errors that were hard to track
down as to why. Moving them out fixed it.
|
||
|
Sonny Jeon
|
0746a5a1d7 |
Organizational updates. Mega2560 support moved.
- Mega2560 support has been moved to the Grbl-Mega [project](http://github.com/gnea/grbl-Mega/) to clean up the code and make future developments easier with increased flash and RAM. All new developments between the 328p and Mega2560 will be synced when it makes sense to. - OEM single file compile configuration option. Before OEMs needed to alter three files. Provided a way to just alter the config.h file to contain everything for a particular Grbl build. See config.h for more details. - Removed defaults and cpu_map directories and reverted back to defaults.h and cpu_map.h to contain all definitions. This should help reduce some headaches and the previous implementation inadvertently created. Also, it makes the single file config.h possible. - Moved (and tweaked) the invert control pin mask define and placed into config.h, rather than in the cpu_map.h file. Makes more sense there. |
||
|
Sonny Jeon
|
d0919142c5 |
Added X-Carve defaults.
- Added X-Carve 500mm and 1000mm default files. - Tweaked all default files. Removed obsolete AUTO_START and updated some JUNCTION_DEVIATION defaults after testing showed these needed to be reduced slightly. |
||
|
Sonny Jeon
|
f85c481ded |
Homing and limit updates. Minor bug fixes.
- Updated new homing cycle to error out when a pull-off motion detects the limit is still active. - Created a limits_get_state() function to centralize it. It reports state as a bit-wise booleans according to axis numbering. - Updated the print uint8 functions. Generalized it to allow both base2 and base10 printouts, while allowing base2 prints with N_AXIS digits for limit state status reports. Doing this saved about 100bytes of flash as well. - Applied CoreXY status reporting bug fix by @phd0. Thanks! |
||
ashelly
|
b58e8455c9 | Moving defaults to individual files in subdirectory | ||
|
Sonny Jeon
|
664854b9df |
Critical M0/2/30 fix. Homing updates.
- Critical fix for M0 program pause. Due to its recent change, it would cause Grbl to suspend but wouldn’t notify the user of why Grbl was not doing anything. The state would show IDLE and a cycle start would resume it. Grbl now enters a HOLD state to better indicate the state change. - Critical fix for M2 and M30 program end. As with M0, the state previously would show IDLE while suspended. Grbl now does not suspend upon program end and leaves job control to the GUI. Grbl simply reports a `[Pgm End]` as a feedback message and resets certain g-code modes. - M2/30 g-code reseting fix. Previously Grbl would soft-reset after an M2/30, but this was not complaint to the (linuxcnc) g-code standard. It simply resets [G1,G17,G90,G94,G40,G54,M5,M9,M48] and keeps all other modes the same. - M0/M2/M30 check-mode fix. It now does not suspend the machine during check-mode. - Minor bug fix related to commands similar to G90.1, but not G90.1, not reporting an unsupported command. - Homing cycle refactoring. To help reduce the chance of users misunderstanding their limit switch wiring, Grbl only moves a short distance for the locate cycles only. In addition, the homing cycle pulls-off the limit switch by the pull-off distance to re-engage and locate home. This should improve its accuracy. - HOMING_FORCE_ORIGIN now sets the origin to the pull-off location, rather than where the limit switch was triggered. - Updated default junction deviation to 0.01mm. Recent tests showed that this improves Grbl’s cornering behavior a bit. - Added the ShapeOko3 defaults. - Added new feedback message `[Pgm End]` for M2/30 notification. - Limit pin reporting is now a $10 status report option. Requested by OEMs to help simplify support troubleshooting. |
||
|
Sonny Jeon
|
8c9fc7943e |
Homing alarm upon no switch. Licensing update.
- Homing cycle failure reports alarm feedback when the homing cycle is exited via a reset, interrupted by a safety door switch, or does not find the limit switch. - Homing cycle bug fix when not finding the limit switch. It would just idle before, but now will exit with an alarm. - Licensing update. Corrected licensing according to lawyer recommendations. Removed references to other Grbl versions. |
||
|
Sonny Jeon
|
b237ad566a |
File re-organization. New Makefile.
- Re-organized source code files into a ‘grbl’ directory to lessen one step in compiling Grbl through the Arduino IDE. - Added an ‘examples’ directory with an upload .INO sketch to further simplify compiling and uploading Grbl via the Arduino IDE. - Updated the Makefile with regard to the source code no longer being in the root directory. All files generated by compiling is placed in a separate ‘build’ directory to keep things tidy. The makefile should operate in the same way as it did before. |