664854b9df
- Critical fix for M0 program pause. Due to its recent change, it would cause Grbl to suspend but wouldn’t notify the user of why Grbl was not doing anything. The state would show IDLE and a cycle start would resume it. Grbl now enters a HOLD state to better indicate the state change. - Critical fix for M2 and M30 program end. As with M0, the state previously would show IDLE while suspended. Grbl now does not suspend upon program end and leaves job control to the GUI. Grbl simply reports a `[Pgm End]` as a feedback message and resets certain g-code modes. - M2/30 g-code reseting fix. Previously Grbl would soft-reset after an M2/30, but this was not complaint to the (linuxcnc) g-code standard. It simply resets [G1,G17,G90,G94,G40,G54,M5,M9,M48] and keeps all other modes the same. - M0/M2/M30 check-mode fix. It now does not suspend the machine during check-mode. - Minor bug fix related to commands similar to G90.1, but not G90.1, not reporting an unsupported command. - Homing cycle refactoring. To help reduce the chance of users misunderstanding their limit switch wiring, Grbl only moves a short distance for the locate cycles only. In addition, the homing cycle pulls-off the limit switch by the pull-off distance to re-engage and locate home. This should improve its accuracy. - HOMING_FORCE_ORIGIN now sets the origin to the pull-off location, rather than where the limit switch was triggered. - Updated default junction deviation to 0.01mm. Recent tests showed that this improves Grbl’s cornering behavior a bit. - Added the ShapeOko3 defaults. - Added new feedback message `[Pgm End]` for M2/30 notification. - Limit pin reporting is now a $10 status report option. Requested by OEMs to help simplify support troubleshooting.
336 lines
16 KiB
C
336 lines
16 KiB
C
/*
|
|
defaults.h - defaults settings configuration file
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2012-2015 Sungeun K. Jeon
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/* The defaults.h file serves as a central default settings file for different machine
|
|
types, from DIY CNC mills to CNC conversions of off-the-shelf machines. The settings
|
|
here are supplied by users, so your results may vary. However, this should give you
|
|
a good starting point as you get to know your machine and tweak the settings for your
|
|
our nefarious needs. */
|
|
|
|
#ifndef defaults_h
|
|
#define defaults_h
|
|
|
|
#ifdef DEFAULTS_GENERIC
|
|
// Grbl generic default settings. Should work across different machines.
|
|
#define DEFAULT_X_STEPS_PER_MM 250.0
|
|
#define DEFAULT_Y_STEPS_PER_MM 250.0
|
|
#define DEFAULT_Z_STEPS_PER_MM 250.0
|
|
#define DEFAULT_X_MAX_RATE 500.0 // mm/min
|
|
#define DEFAULT_Y_MAX_RATE 500.0 // mm/min
|
|
#define DEFAULT_Z_MAX_RATE 500.0 // mm/min
|
|
#define DEFAULT_X_ACCELERATION (10.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
|
|
#define DEFAULT_Y_ACCELERATION (10.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
|
|
#define DEFAULT_Z_ACCELERATION (10.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
|
|
#define DEFAULT_X_MAX_TRAVEL 200.0 // mm
|
|
#define DEFAULT_Y_MAX_TRAVEL 200.0 // mm
|
|
#define DEFAULT_Z_MAX_TRAVEL 200.0 // mm
|
|
#define DEFAULT_STEP_PULSE_MICROSECONDS 10
|
|
#define DEFAULT_STEPPING_INVERT_MASK 0
|
|
#define DEFAULT_DIRECTION_INVERT_MASK 0
|
|
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 25 // msec (0-254, 255 keeps steppers enabled)
|
|
#define DEFAULT_STATUS_REPORT_MASK ((BITFLAG_RT_STATUS_MACHINE_POSITION)|(BITFLAG_RT_STATUS_WORK_POSITION))
|
|
#define DEFAULT_JUNCTION_DEVIATION 0.02 // mm
|
|
#define DEFAULT_ARC_TOLERANCE 0.002 // mm
|
|
#define DEFAULT_REPORT_INCHES 0 // false
|
|
#define DEFAULT_INVERT_ST_ENABLE 0 // false
|
|
#define DEFAULT_INVERT_LIMIT_PINS 0 // false
|
|
#define DEFAULT_SOFT_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HARD_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_DIR_MASK 0 // move positive dir
|
|
#define DEFAULT_HOMING_FEED_RATE 25.0 // mm/min
|
|
#define DEFAULT_HOMING_SEEK_RATE 500.0 // mm/min
|
|
#define DEFAULT_HOMING_DEBOUNCE_DELAY 250 // msec (0-65k)
|
|
#define DEFAULT_HOMING_PULLOFF 1.0 // mm
|
|
#endif
|
|
|
|
|
|
|
|
#ifdef DEFAULTS_SHERLINE_5400
|
|
// Description: Sherline 5400 mill with three NEMA 23 Keling KL23H256-21-8B 185 oz-in stepper motors,
|
|
// driven by three Pololu A4988 stepper drivers with a 30V, 6A power supply at 1.5A per winding.
|
|
#define MICROSTEPS 2
|
|
#define STEPS_PER_REV 200.0
|
|
#define MM_PER_REV (0.050*MM_PER_INCH) // 0.050 inch/rev leadscrew
|
|
#define DEFAULT_X_STEPS_PER_MM (STEPS_PER_REV*MICROSTEPS/MM_PER_REV)
|
|
#define DEFAULT_Y_STEPS_PER_MM (STEPS_PER_REV*MICROSTEPS/MM_PER_REV)
|
|
#define DEFAULT_Z_STEPS_PER_MM (STEPS_PER_REV*MICROSTEPS/MM_PER_REV)
|
|
#define DEFAULT_X_MAX_RATE 635.0 // mm/min (25 ipm)
|
|
#define DEFAULT_Y_MAX_RATE 635.0 // mm/min
|
|
#define DEFAULT_Z_MAX_RATE 635.0 // mm/min
|
|
#define DEFAULT_X_ACCELERATION (50.0*60*60) // 50*60*60 mm/min^2 = 50 mm/sec^2
|
|
#define DEFAULT_Y_ACCELERATION (50.0*60*60) // 50*60*60 mm/min^2 = 50 mm/sec^2
|
|
#define DEFAULT_Z_ACCELERATION (50.0*60*60) // 50*60*60 mm/min^2 = 50 mm/sec^2
|
|
#define DEFAULT_X_MAX_TRAVEL 225.0 // mm
|
|
#define DEFAULT_Y_MAX_TRAVEL 125.0 // mm
|
|
#define DEFAULT_Z_MAX_TRAVEL 170.0 // mm
|
|
#define DEFAULT_STEP_PULSE_MICROSECONDS 10
|
|
#define DEFAULT_STEPPING_INVERT_MASK 0
|
|
#define DEFAULT_DIRECTION_INVERT_MASK ((1<<Y_AXIS)|(1<<Z_AXIS))
|
|
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 25 // msec (0-254, 255 keeps steppers enabled)
|
|
#define DEFAULT_STATUS_REPORT_MASK ((BITFLAG_RT_STATUS_MACHINE_POSITION)|(BITFLAG_RT_STATUS_WORK_POSITION))
|
|
#define DEFAULT_JUNCTION_DEVIATION 0.01 // mm
|
|
#define DEFAULT_ARC_TOLERANCE 0.002 // mm
|
|
#define DEFAULT_REPORT_INCHES 0 // true
|
|
#define DEFAULT_INVERT_ST_ENABLE 0 // false
|
|
#define DEFAULT_INVERT_LIMIT_PINS 0 // false
|
|
#define DEFAULT_SOFT_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HARD_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_DIR_MASK 0 // move positive dir
|
|
#define DEFAULT_HOMING_FEED_RATE 50.0 // mm/min
|
|
#define DEFAULT_HOMING_SEEK_RATE 635.0 // mm/min
|
|
#define DEFAULT_HOMING_DEBOUNCE_DELAY 250 // msec (0-65k)
|
|
#define DEFAULT_HOMING_PULLOFF 1.0 // mm
|
|
#endif
|
|
|
|
#ifdef DEFAULTS_SHAPEOKO
|
|
// Description: Shapeoko CNC mill with three NEMA 17 stepper motors, driven by Synthetos
|
|
// grblShield with a 24V, 4.2A power supply.
|
|
#define MICROSTEPS_XY 8
|
|
#define STEP_REVS_XY 400
|
|
#define MM_PER_REV_XY (0.08*18*MM_PER_INCH) // 0.08 in belt pitch, 18 pulley teeth
|
|
#define MICROSTEPS_Z 2
|
|
#define STEP_REVS_Z 400
|
|
#define MM_PER_REV_Z 1.250 // 1.25 mm/rev leadscrew
|
|
#define DEFAULT_X_STEPS_PER_MM (MICROSTEPS_XY*STEP_REVS_XY/MM_PER_REV_XY)
|
|
#define DEFAULT_Y_STEPS_PER_MM (MICROSTEPS_XY*STEP_REVS_XY/MM_PER_REV_XY)
|
|
#define DEFAULT_Z_STEPS_PER_MM (MICROSTEPS_Z*STEP_REVS_Z/MM_PER_REV_Z)
|
|
#define DEFAULT_X_MAX_RATE 1000.0 // mm/min
|
|
#define DEFAULT_Y_MAX_RATE 1000.0 // mm/min
|
|
#define DEFAULT_Z_MAX_RATE 1000.0 // mm/min
|
|
#define DEFAULT_X_ACCELERATION (15.0*60*60) // 15*60*60 mm/min^2 = 15 mm/sec^2
|
|
#define DEFAULT_Y_ACCELERATION (15.0*60*60) // 15*60*60 mm/min^2 = 15 mm/sec^2
|
|
#define DEFAULT_Z_ACCELERATION (15.0*60*60) // 15*60*60 mm/min^2 = 15 mm/sec^2
|
|
#define DEFAULT_X_MAX_TRAVEL 200.0 // mm
|
|
#define DEFAULT_Y_MAX_TRAVEL 200.0 // mm
|
|
#define DEFAULT_Z_MAX_TRAVEL 200.0 // mm
|
|
#define DEFAULT_STEP_PULSE_MICROSECONDS 10
|
|
#define DEFAULT_STEPPING_INVERT_MASK 0
|
|
#define DEFAULT_DIRECTION_INVERT_MASK ((1<<Y_AXIS)|(1<<Z_AXIS))
|
|
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 255 // msec (0-254, 255 keeps steppers enabled)
|
|
#define DEFAULT_STATUS_REPORT_MASK ((BITFLAG_RT_STATUS_MACHINE_POSITION)|(BITFLAG_RT_STATUS_WORK_POSITION))
|
|
#define DEFAULT_JUNCTION_DEVIATION 0.02 // mm
|
|
#define DEFAULT_ARC_TOLERANCE 0.002 // mm
|
|
#define DEFAULT_REPORT_INCHES 0 // false
|
|
#define DEFAULT_INVERT_ST_ENABLE 0 // false
|
|
#define DEFAULT_INVERT_LIMIT_PINS 0 // false
|
|
#define DEFAULT_SOFT_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HARD_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_DIR_MASK 0 // move positive dir
|
|
#define DEFAULT_HOMING_FEED_RATE 25.0 // mm/min
|
|
#define DEFAULT_HOMING_SEEK_RATE 250.0 // mm/min
|
|
#define DEFAULT_HOMING_DEBOUNCE_DELAY 250 // msec (0-65k)
|
|
#define DEFAULT_HOMING_PULLOFF 1.0 // mm
|
|
#endif
|
|
|
|
#ifdef DEFAULTS_SHAPEOKO_2
|
|
// Description: Shapeoko CNC mill with three NEMA 17 stepper motors, driven by Synthetos
|
|
// grblShield at 28V.
|
|
#define MICROSTEPS_XY 8
|
|
#define STEP_REVS_XY 200
|
|
#define MM_PER_REV_XY (2.0*20) // 2mm belt pitch, 20 pulley teeth
|
|
#define MICROSTEPS_Z 2
|
|
#define STEP_REVS_Z 200
|
|
#define MM_PER_REV_Z 1.250 // 1.25 mm/rev leadscrew
|
|
#define DEFAULT_X_STEPS_PER_MM (MICROSTEPS_XY*STEP_REVS_XY/MM_PER_REV_XY)
|
|
#define DEFAULT_Y_STEPS_PER_MM (MICROSTEPS_XY*STEP_REVS_XY/MM_PER_REV_XY)
|
|
#define DEFAULT_Z_STEPS_PER_MM (MICROSTEPS_Z*STEP_REVS_Z/MM_PER_REV_Z)
|
|
#define DEFAULT_X_MAX_RATE 5000.0 // mm/min
|
|
#define DEFAULT_Y_MAX_RATE 5000.0 // mm/min
|
|
#define DEFAULT_Z_MAX_RATE 500.0 // mm/min
|
|
#define DEFAULT_X_ACCELERATION (250.0*60*60) // 25*60*60 mm/min^2 = 25 mm/sec^2
|
|
#define DEFAULT_Y_ACCELERATION (250.0*60*60) // 25*60*60 mm/min^2 = 25 mm/sec^2
|
|
#define DEFAULT_Z_ACCELERATION (50.0*60*60) // 25*60*60 mm/min^2 = 25 mm/sec^2
|
|
#define DEFAULT_X_MAX_TRAVEL 290.0 // mm
|
|
#define DEFAULT_Y_MAX_TRAVEL 290.0 // mm
|
|
#define DEFAULT_Z_MAX_TRAVEL 100.0 // mm
|
|
#define DEFAULT_STEP_PULSE_MICROSECONDS 10
|
|
#define DEFAULT_STEPPING_INVERT_MASK 0
|
|
#define DEFAULT_DIRECTION_INVERT_MASK ((1<<X_AXIS)|(1<<Z_AXIS))
|
|
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 255 // msec (0-254, 255 keeps steppers enabled)
|
|
#define DEFAULT_STATUS_REPORT_MASK ((BITFLAG_RT_STATUS_MACHINE_POSITION)|(BITFLAG_RT_STATUS_WORK_POSITION))
|
|
#define DEFAULT_JUNCTION_DEVIATION 0.02 // mm
|
|
#define DEFAULT_ARC_TOLERANCE 0.002 // mm
|
|
#define DEFAULT_REPORT_INCHES 0 // false
|
|
#define DEFAULT_INVERT_ST_ENABLE 0 // false
|
|
#define DEFAULT_INVERT_LIMIT_PINS 0 // false
|
|
#define DEFAULT_SOFT_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HARD_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_DIR_MASK 0 // move positive dir
|
|
#define DEFAULT_HOMING_FEED_RATE 25.0 // mm/min
|
|
#define DEFAULT_HOMING_SEEK_RATE 250.0 // mm/min
|
|
#define DEFAULT_HOMING_DEBOUNCE_DELAY 250 // msec (0-65k)
|
|
#define DEFAULT_HOMING_PULLOFF 1.0 // mm
|
|
#endif
|
|
|
|
#ifdef DEFAULTS_SHAPEOKO_3
|
|
// Description: Shapeoko CNC mill with three NEMA 23 stepper motors, driven by CarbideMotion
|
|
#define MICROSTEPS_XY 8
|
|
#define STEP_REVS_XY 200
|
|
#define MM_PER_REV_XY (2.0*20) // 2mm belt pitch, 20 pulley teeth
|
|
#define MICROSTEPS_Z 8
|
|
#define STEP_REVS_Z 200
|
|
#define MM_PER_REV_Z (2.0*20) // 2mm belt pitch, 20 pulley teeth
|
|
#define DEFAULT_X_STEPS_PER_MM (MICROSTEPS_XY*STEP_REVS_XY/MM_PER_REV_XY)
|
|
#define DEFAULT_Y_STEPS_PER_MM (MICROSTEPS_XY*STEP_REVS_XY/MM_PER_REV_XY)
|
|
#define DEFAULT_Z_STEPS_PER_MM (MICROSTEPS_Z*STEP_REVS_Z/MM_PER_REV_Z)
|
|
#define DEFAULT_X_MAX_RATE 5000.0 // mm/min
|
|
#define DEFAULT_Y_MAX_RATE 5000.0 // mm/min
|
|
#define DEFAULT_Z_MAX_RATE 5000.0 // mm/min
|
|
#define DEFAULT_X_ACCELERATION (400.0*60*60) // 400*60*60 mm/min^2 = 400 mm/sec^2
|
|
#define DEFAULT_Y_ACCELERATION (400.0*60*60) // 400*60*60 mm/min^2 = 400 mm/sec^2
|
|
#define DEFAULT_Z_ACCELERATION (400.0*60*60) // 400*60*60 mm/min^2 = 400 mm/sec^2
|
|
#define DEFAULT_X_MAX_TRAVEL 425.0 // mm
|
|
#define DEFAULT_Y_MAX_TRAVEL 465.0 // mm
|
|
#define DEFAULT_Z_MAX_TRAVEL 80.0 // mm
|
|
#define DEFAULT_STEP_PULSE_MICROSECONDS 10
|
|
#define DEFAULT_STEPPING_INVERT_MASK 0
|
|
#define DEFAULT_DIRECTION_INVERT_MASK ((1<<X_AXIS)|(1<<Z_AXIS))
|
|
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 255 // msec (0-254, 255 keeps steppers enabled)
|
|
#define DEFAULT_STATUS_REPORT_MASK 255 // All enabled
|
|
#define DEFAULT_JUNCTION_DEVIATION 0.02 // mm
|
|
#define DEFAULT_ARC_TOLERANCE 0.01 // mm
|
|
#define DEFAULT_REPORT_INCHES 0 // false
|
|
#define DEFAULT_INVERT_ST_ENABLE 0 // false
|
|
#define DEFAULT_INVERT_LIMIT_PINS 0 // false
|
|
#define DEFAULT_SOFT_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HARD_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_DIR_MASK 0 // move positive dir
|
|
#define DEFAULT_HOMING_FEED_RATE 100.0 // mm/min
|
|
#define DEFAULT_HOMING_SEEK_RATE 1000.0 // mm/min
|
|
#define DEFAULT_HOMING_DEBOUNCE_DELAY 25 // msec (0-65k)
|
|
#define DEFAULT_HOMING_PULLOFF 5.0 // mm
|
|
#endif
|
|
|
|
#ifdef DEFAULTS_ZEN_TOOLWORKS_7x7
|
|
// Description: Zen Toolworks 7x7 mill with three Shinano SST43D2121 65oz-in NEMA 17 stepper motors.
|
|
// Leadscrew is different from some ZTW kits, where most are 1.25mm/rev rather than 8.0mm/rev here.
|
|
// Driven by 30V, 6A power supply and TI DRV8811 stepper motor drivers.
|
|
#define MICROSTEPS 8
|
|
#define STEPS_PER_REV 200.0
|
|
#define MM_PER_REV 8.0 // 8 mm/rev leadscrew
|
|
#define DEFAULT_X_STEPS_PER_MM (STEPS_PER_REV*MICROSTEPS/MM_PER_REV)
|
|
#define DEFAULT_Y_STEPS_PER_MM (STEPS_PER_REV*MICROSTEPS/MM_PER_REV)
|
|
#define DEFAULT_Z_STEPS_PER_MM (STEPS_PER_REV*MICROSTEPS/MM_PER_REV)
|
|
#define DEFAULT_X_MAX_RATE 6000.0 // mm/min
|
|
#define DEFAULT_Y_MAX_RATE 6000.0 // mm/min
|
|
#define DEFAULT_Z_MAX_RATE 6000.0 // mm/min
|
|
#define DEFAULT_X_ACCELERATION (600.0*60*60) // 600*60*60 mm/min^2 = 600 mm/sec^2
|
|
#define DEFAULT_Y_ACCELERATION (600.0*60*60) // 600*60*60 mm/min^2 = 600 mm/sec^2
|
|
#define DEFAULT_Z_ACCELERATION (600.0*60*60) // 600*60*60 mm/min^2 = 600 mm/sec^2
|
|
#define DEFAULT_X_MAX_TRAVEL 190.0 // mm
|
|
#define DEFAULT_Y_MAX_TRAVEL 180.0 // mm
|
|
#define DEFAULT_Z_MAX_TRAVEL 150.0 // mm
|
|
#define DEFAULT_STEP_PULSE_MICROSECONDS 10
|
|
#define DEFAULT_STEPPING_INVERT_MASK 0
|
|
#define DEFAULT_DIRECTION_INVERT_MASK ((1<<Y_AXIS))
|
|
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 25 // msec (0-254, 255 keeps steppers enabled)
|
|
#define DEFAULT_STATUS_REPORT_MASK ((BITFLAG_RT_STATUS_MACHINE_POSITION)|(BITFLAG_RT_STATUS_WORK_POSITION))
|
|
#define DEFAULT_JUNCTION_DEVIATION 0.02 // mm
|
|
#define DEFAULT_ARC_TOLERANCE 0.002 // mm
|
|
#define DEFAULT_REPORT_INCHES 0 // false
|
|
#define DEFAULT_INVERT_ST_ENABLE 0 // false
|
|
#define DEFAULT_INVERT_LIMIT_PINS 0 // false
|
|
#define DEFAULT_SOFT_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HARD_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_DIR_MASK 0 // move positive dir
|
|
#define DEFAULT_HOMING_FEED_RATE 25.0 // mm/min
|
|
#define DEFAULT_HOMING_SEEK_RATE 250.0 // mm/min
|
|
#define DEFAULT_HOMING_DEBOUNCE_DELAY 250 // msec (0-65k)
|
|
#define DEFAULT_HOMING_PULLOFF 1.0 // mm
|
|
#endif
|
|
|
|
#ifdef DEFAULTS_OXCNC
|
|
// Grbl settings for OpenBuilds OX CNC Machine
|
|
// http://www.openbuilds.com/builds/openbuilds-ox-cnc-machine.341/
|
|
#define DEFAULT_X_STEPS_PER_MM 26.670
|
|
#define DEFAULT_Y_STEPS_PER_MM 26.670
|
|
#define DEFAULT_Z_STEPS_PER_MM 50
|
|
#define DEFAULT_X_MAX_RATE 500.0 // mm/min
|
|
#define DEFAULT_Y_MAX_RATE 500.0 // mm/min
|
|
#define DEFAULT_Z_MAX_RATE 500.0 // mm/min
|
|
#define DEFAULT_X_ACCELERATION (10.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
|
|
#define DEFAULT_Y_ACCELERATION (10.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
|
|
#define DEFAULT_Z_ACCELERATION (10.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
|
|
#define DEFAULT_X_MAX_TRAVEL 500.0 // mm
|
|
#define DEFAULT_Y_MAX_TRAVEL 750.0 // mm
|
|
#define DEFAULT_Z_MAX_TRAVEL 80.0 // mm
|
|
#define DEFAULT_STEP_PULSE_MICROSECONDS 10
|
|
#define DEFAULT_STEPPING_INVERT_MASK 0
|
|
#define DEFAULT_DIRECTION_INVERT_MASK 0
|
|
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 25 // msec (0-254, 255 keeps steppers enabled)
|
|
#define DEFAULT_STATUS_REPORT_MASK ((BITFLAG_RT_STATUS_MACHINE_POSITION)|(BITFLAG_RT_STATUS_WORK_POSITION))
|
|
#define DEFAULT_JUNCTION_DEVIATION 0.02 // mm
|
|
#define DEFAULT_ARC_TOLERANCE 0.002 // mm
|
|
#define DEFAULT_REPORT_INCHES 0 // false
|
|
#define DEFAULT_INVERT_ST_ENABLE 0 // false
|
|
#define DEFAULT_INVERT_LIMIT_PINS 0 // false
|
|
#define DEFAULT_SOFT_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HARD_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_DIR_MASK 0 // move positive dir
|
|
#define DEFAULT_HOMING_FEED_RATE 25.0 // mm/min
|
|
#define DEFAULT_HOMING_SEEK_RATE 500.0 // mm/min
|
|
#define DEFAULT_HOMING_DEBOUNCE_DELAY 250 // msec (0-65k)
|
|
#define DEFAULT_HOMING_PULLOFF 1.0 // mm
|
|
#endif
|
|
|
|
#ifdef DEFAULTS_SIMULATOR
|
|
// Settings only for Grbl Simulator (www.github.com/grbl/grbl-sim)
|
|
// Grbl generic default settings. Should work across different machines.
|
|
#define DEFAULT_X_STEPS_PER_MM 1000.0
|
|
#define DEFAULT_Y_STEPS_PER_MM 1000.0
|
|
#define DEFAULT_Z_STEPS_PER_MM 1000.0
|
|
#define DEFAULT_X_MAX_RATE 1000.0 // mm/min
|
|
#define DEFAULT_Y_MAX_RATE 1000.0 // mm/min
|
|
#define DEFAULT_Z_MAX_RATE 1000.0 // mm/min
|
|
#define DEFAULT_X_ACCELERATION (100.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
|
|
#define DEFAULT_Y_ACCELERATION (100.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
|
|
#define DEFAULT_Z_ACCELERATION (100.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
|
|
#define DEFAULT_X_MAX_TRAVEL 1000.0 // mm
|
|
#define DEFAULT_Y_MAX_TRAVEL 1000.0 // mm
|
|
#define DEFAULT_Z_MAX_TRAVEL 1000.0 // mm
|
|
#define DEFAULT_STEP_PULSE_MICROSECONDS 10
|
|
#define DEFAULT_STEPPING_INVERT_MASK 0
|
|
#define DEFAULT_DIRECTION_INVERT_MASK 0
|
|
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 25 // msec (0-254, 255 keeps steppers enabled)
|
|
#define DEFAULT_STATUS_REPORT_MASK ((BITFLAG_RT_STATUS_MACHINE_POSITION)|(BITFLAG_RT_STATUS_WORK_POSITION))
|
|
#define DEFAULT_JUNCTION_DEVIATION 0.02 // mm
|
|
#define DEFAULT_ARC_TOLERANCE 0.002 // mm
|
|
#define DEFAULT_REPORT_INCHES 0 // false
|
|
#define DEFAULT_INVERT_ST_ENABLE 0 // false
|
|
#define DEFAULT_INVERT_LIMIT_PINS 0 // false
|
|
#define DEFAULT_SOFT_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HARD_LIMIT_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_ENABLE 0 // false
|
|
#define DEFAULT_HOMING_DIR_MASK 0 // move positive dir
|
|
#define DEFAULT_HOMING_FEED_RATE 25.0 // mm/min
|
|
#define DEFAULT_HOMING_SEEK_RATE 500.0 // mm/min
|
|
#define DEFAULT_HOMING_DEBOUNCE_DELAY 250 // msec (0-65k)
|
|
#define DEFAULT_HOMING_PULLOFF 1.0 // mm
|
|
#endif
|
|
|
|
#endif
|