ManuelW/grbl-LPC-CoreXY
1
0
Fork 0
Code Issues Pull Requests Releases 1 Wiki Activity
d226555810
grbl-LPC-CoreXY/README.md
Sonny Jeon d226555810 Minor bug fixes. 
- G38.x was not printing correctly in the $G g-code state reports. Now
fixed.

- Potential bug regarding volatile variables inside a struct. It has
never been a problem in v0.9, but ran into this during v1.0
development. Just to be safe, the fixes are applied here.

- Updated pre-built firmwares with these two bug fixes.
2015-09-30 20:53:35 -06:00

5.6 KiB
Raw Blame History

![GitHub Logo](/doc/media/Grbl Logo 250px.png)

Grbl is a no-compromise, high performance, low cost alternative to parallel-port-based motion control for CNC milling. It will run on a vanilla Arduino (Duemillanove/Uno) as long as it sports an Atmega 328.

The controller is written in highly optimized C utilizing every clever feature of the AVR-chips to achieve precise timing and asynchronous operation. It is able to maintain up to 30kHz of stable, jitter free control pulses.

It accepts standards-compliant g-code and has been tested with the output of several CAM tools with no problems. Arcs, circles and helical motion are fully supported, as well as, all other primary g-code commands. Macro functions, variables, and most canned cycles are not supported, but we think GUIs can do a much better job at translating them into straight g-code anyhow.

Grbl includes full acceleration management with look ahead. That means the controller will look up to 18 motions into the future and plan its velocities ahead to deliver smooth acceleration and jerk-free cornering.

  • Licensing: Grbl is free software, released under the GPLv3 license.

  • For more information and help, check out our Wiki pages! If you find that the information is out-dated, please to help us keep it updated by editing it or notifying our community! Thanks!

  • Lead Developer [2011 - Current]: Sungeun(Sonny) K. Jeon, Ph.D. (USA) aka @chamnit

  • Lead Developer [2009 - 2011]: Simen Svale Skogsrud (Norway). aka The Originator/Creator/Pioneer/Father of Grbl.

Official Supporters of the Grbl CNC Project

Official Supporters

Master Branch:

Archives:

##Update Summary for v0.9j

  • Restore EEPROM feature: A new set of restore EEPROM features to help OEMs and users reset their Grbl installation to the build defaults. See Configuring Grbl Wiki for details.

##Update Summary for v0.9i

  • IMPORTANT:
    • Homing cycle updated. Locates based on trigger point, rather than release point.
    • System tweaks: $14 cycle auto-start has been removed. No more QUEUE state.
  • New G-Codes
  • CoreXY Support
  • Safety Door Support
  • Full Limit and Control Pin Configurability
  • Additional Compile-Time Feature Options

##Update Summary for v0.9h from v0.8

  • IMPORTANT:

    • Default serial baudrate is now 115200! (Up from 9600)
    • Z-limit(D12) and spindle enable(D11) pins have switched to support variable spindle!

  • Super Smooth Stepper Algorithm

  • Stability and Robustness Updates

  • (x4)+ Faster Planner

  • Compile-able via Arduino IDE!

  • G-Code Parser Overhaul

  • Independent Acceleration and Velocity Settings

  • Soft Limits

  • Probing

  • Dynamic Tool Length Offsets

  • Improved Arc Performance

  • CPU Pin Mapping

  • New Grbl SIMULATOR! (by @jgeisler and @ashelly)

  • Configurable Real-time Status Reporting

  • Updated Homing Routine

  • Optional Limit Pin Sharing

  • Optional Variable Spindle Speed Output

  • Additional Compile-Time Feature Options

List of Supported G-Codes in Grbl v0.9 Master:
  - Non-Modal Commands: G4, G10L2, G10L20, G28, G30, G28.1, G30.1, G53, G92, G92.1
  - Motion Modes: G0, G1, G2, G3, G38.2, G38.3, G38.4, G38.5, G80
  - Feed Rate Modes: G93, G94
  - Unit Modes: G20, G21
  - Distance Modes: G90, G91
  - Arc IJK Distance Modes: G91.1
  - Plane Select Modes: G17, G18, G19
  - Tool Length Offset Modes: G43.1, G49
  - Cutter Compensation Modes: G40
  - Coordinate System Modes: G54, G55, G56, G57, G58, G59
  - Control Modes: G61
  - Program Flow: M0, M1, M2, M30*
  - Coolant Control: M7*, M8, M9
  - Spindle Control: M3, M4, M5
  - Valid Non-Command Words: F, I, J, K, L, N, P, R, S, T, X, Y, Z

Grbl is an open-source project and fueled by the free-time of our intrepid administrators and altruistic users. If you'd like to donate, all proceeds will be used to help fund supporting hardware and testing equipment. Thank you!

Donate