(All v0.8 features installed. Still likely buggy, but now thourough
testing will need to start to squash them all. As soon as we're done,
this will be pushed to master and v0.9 development will be started.
Please report ANY issues to us so we can get this rolled out ASAP.)
- User startup script! A user can now save one (up to 5 as compile-time
option) block of g-code in EEPROM memory. This will be run everytime
Grbl resets. Mainly to be used as a way to set your preferences, like
G21, G54, etc.
- New dry run and check g-code switches. Dry run moves ALL motions at
rapids rate ignoring spindle, coolant, and dwell commands. For rapid
physical proofing of your code. The check g-code switch ignores all
motion and provides the user a way to check if there are any errors in
their program that Grbl may not like.
- Program restart! (sort of). Program restart is typically an advanced
feature that allows users to restart a program mid-stream. The check
g-code switch can perform this feature by enabling the switch at the
start of the program, and disabling it at the desired point with some
minimal changes.
- New system state variable. This state variable tracks all of the
different state processes that Grbl performs, i.e. cycle start, feed
hold, homing, etc. This is mainly for making managing of these task
easier and more clear.
- Position lost state variable. Only when homing is enabled, Grbl will
refuse to move until homing is completed and position is known. This is
mainly for safety. Otherwise, it will let users fend for themselves.
- Moved the default settings defines into config.h. The plan is to
eventually create a set of config.h's for particular as-built machines
to help users from doing it themselves.
- Moved around misc defines into .h files. And lots of other little
things.
(NOTE: This push is likely buggy so proceed with caution. Just
uploading to let people know where we're going.)
- New report.c module. Moved all feedback functions into this module to
centralize these processes. Includes realtime status reports, status
messages, feedback messages.
- Official support 6 work coordinate systems (G54-G59), which are
persistently held in EEPROM memory.
- New g-code support: G28.1, G30.1 stores current machine position as a
home position into EEPROM. G10 L20 Px stores current machine position
into work coordinates without needing to explicitly send XYZ words.
- Homing performed with '$H' command. G28/G30 no longer start the
homing cycle. This is how it's supposed to be.
- New settings: Stepper enable invert and n_arc correction installed.
- Updated and changed up some limits and homing functionality. Pull-off
travel will now move after the homing cycle regardless of hard limits
enabled. Fixed direction of pull-off travel (went wrong way).
- Started on designing an internal Grbl command protocol based on the
'$' settings letter. Commands with non numeric characters after '$'
will perform switch commands, homing cycle, jogging, printing
paramters, etc. Much more to do here.
- Updated README to reflect all of the new features.
- Installed a new 'alarm' method to centralize motion kills across
alarm or reset events. Right now, this is controlled by system abort
and hard limits. But, in the future, a g-code parser error may call
this too as a safety feature.
- Re(re)organized status messages to just print all errors, regardless
from where it was called. This centralizes them into one place.
- Misc messages method installed for any user feedback that is not a
confirmation or error. Mainly so that there is a place to perform
warnings and such.
- New stuff installed and still made the flash size smaller by saving
flash space from clearing out repeated '\r\n' pgmstrings.
- Fixed a bug where hard limits message would print everytime a system
abort was sent.
- Fixed a bug that would not disable the steppers if a user issues a
system abort during a homing cycle.
- Updated the hard limit interrupt to be more correct and to issue a
shutdown for the right situations when the switch has been triggered.
- Added a status message to indicate to the user what happened and what
to do upon a hard limit trigger.
- Thank you statement added for Alden Hart of Synthetos.
- Hard limits option added, which also works with homing by pulling off
the switches to help prevent unintended triggering. Hard limits use a
interrupt to sense a falling edge pin change and immediately go into
alarm mode, which stops everything and forces the user to issue a reset
(Ctrl-x) or reboot.
- Auto cycle start now a configuration option.
- Alarm mode: A new method to kill all Grbl processes in the event of
something catastrophic or potentially catastropic. Just works with hard
limits for now, but will be expanded to include g-code errors (most
likely) and other events.
- Updated status reports to be configurable in inches or mm mode. Much
more to do here, but this is the first step.
- New settings: auto cycle start, hard limit enable, homing direction
mask (which works the same as the stepper mask), homing pulloff
distance (or distance traveled from homed machine zero to prevent
accidental limit trip).
- Minor memory liberation and calculation speed ups.
- Allowed status_message function to be called by others. This is to
centralize all feedback into protocol.c.
- Fixed a bug where line number words 'N' were causing the parser to
error out.
- Allowed homing routine feed rates to move slower than the
MINIMUM_STEP_RATE parameter in config.h.
- Homing performs idle lock at the end of the routine.
- Stepper idle lock time will now not disable the steppers when the
value is set at 255. This is accomodate users who prefer to keep their
axes enabled at all times.
- Moved some defines around to where they need to be.
- Homing cycle will now cycle twice (spec more/less in config) to
improve repeatability and accuracy by decreasing overshoot.
- New Grbl settings added: Enable/disable homing cycles, homing seek
and feed rates, switch debounce delay, and stepper idle lock time.
- Please note that these settings may change upon the next push, since
there will be more added soon. Grbl *should* not re-write your old
settings, just re-write the new ones. So, make sure you keep these
written down somewhere in case they get lost from a code bug.
- Refactored settings migration to be a little smaller and managable
going forward.
- Limit pin internal pull-resistors now enabled. Normal high operation.
This will be the standard going forward.
- Updated all of the 'double' variable types to 'float' to reflect what
happens when compiled for the Arduino. Also done for compatibility
reasons to @jgeisler0303 's Grbl simulator code.
- G-code parser will now ignore 'E' exponent values, since they are
reserved g-code characters for some machines. Thanks @csdexter!
- The read_double() function was re-written and optimized for use in
Grbl. The strtod() avr lib was removed.
- Added acceleration to the homing routine.
- Homing now accounts for different step rates when moving multiple
axes without exceeding acceleration limits.
- Homing now updates all internal positioning variables to machine zero
after completion.
- "Poor-man's" debounce delay added.
- Updated the delay_us() function to perform faster and more accurate
microsecond delays. Previously, the single increments would add
noticeable time drift for larger delays.
- Fix a bug in the stepper.c prescalar calculations that was changed in
the last commit.
- Other minor fixes.
- Updated makefile to be more universally compatible by not requiring
grep or ruby.
- Edited XON/XOFF flow control usage, noting that FTDI-based Arduinos
are known to work, but not Atmega8U2-based Arduino. Still officially
not supported, but added for advanced users.
- Minor edits.
- G54 work coordinate system support. Up to 6 work coordinate systems
(G54-G59) available as a compile-time option.
- G10 command added to set work coordinate offsets from machine
position.
- G92/G92.1 position offsets and cancellation support. Properly follows
NIST standard rules with other systems.
- G53 absolute override now works correctly with new coordinate systems.
- Revamped g-code parser with robust error checking. Providing user
feedback with bad commands. Follows NIST standards.
- Planner module slightly changed to only expected position movements
in terms of machine coordinates only. This was to simplify coordinate
system handling, which is done solely by the g-code parser.
- Upon grbl system abort, machine position and work positions are
retained, while G92 offsets are reset per NIST standards.
- Compiler compatibility update for _delay_us().
- Updated README.
- Grbl now tracks both home and work (G92) coordinate systems and does
live updates when G92 is called.
- Rudimentary home and work position status reporting. Works but still
under major construction.
- Updated the main streaming script. Has a disabled periodic timer for
querying status reports, disabled only because the Python timer doesn't
consistently restart after the script exits. Add here only for user
testing.
- Fixed a bug to prevent an endless serial_write loop during status
reports.
- Refactored the planner variables to make it more clear what they are
and make it easier for clear them.
- ALPHA status. - Multitasking ability with run-time command executions
for real-time control and feedback. - Decelerating feed hold and resume
during operation. - System abort/reset, which immediately kills all
movement and re-initializes grbl. - Re-structured grbl to easily allow
for new features: Status reporting, jogging, backlash compensation. (To
be completed in the following releases.) - Resized TX/RX serial buffers
(32/128 bytes) - Increased planner buffer size to 20 blocks. - Updated
documentation.
