- Thank you statement added for Alden Hart of Synthetos.
- Hard limits option added, which also works with homing by pulling off
the switches to help prevent unintended triggering. Hard limits use a
interrupt to sense a falling edge pin change and immediately go into
alarm mode, which stops everything and forces the user to issue a reset
(Ctrl-x) or reboot.
- Auto cycle start now a configuration option.
- Alarm mode: A new method to kill all Grbl processes in the event of
something catastrophic or potentially catastropic. Just works with hard
limits for now, but will be expanded to include g-code errors (most
likely) and other events.
- Updated status reports to be configurable in inches or mm mode. Much
more to do here, but this is the first step.
- New settings: auto cycle start, hard limit enable, homing direction
mask (which works the same as the stepper mask), homing pulloff
distance (or distance traveled from homed machine zero to prevent
accidental limit trip).
- Minor memory liberation and calculation speed ups.
- Allowed status_message function to be called by others. This is to
centralize all feedback into protocol.c.
- Fixed a bug where line number words 'N' were causing the parser to
error out.
- Allowed homing routine feed rates to move slower than the
MINIMUM_STEP_RATE parameter in config.h.
- Homing performs idle lock at the end of the routine.
- Stepper idle lock time will now not disable the steppers when the
value is set at 255. This is accomodate users who prefer to keep their
axes enabled at all times.
- Moved some defines around to where they need to be.
- Homing cycle will now cycle twice (spec more/less in config) to
improve repeatability and accuracy by decreasing overshoot.
- New Grbl settings added: Enable/disable homing cycles, homing seek
and feed rates, switch debounce delay, and stepper idle lock time.
- Please note that these settings may change upon the next push, since
there will be more added soon. Grbl *should* not re-write your old
settings, just re-write the new ones. So, make sure you keep these
written down somewhere in case they get lost from a code bug.
- Refactored settings migration to be a little smaller and managable
going forward.
- Limit pin internal pull-resistors now enabled. Normal high operation.
This will be the standard going forward.
- Updated all of the 'double' variable types to 'float' to reflect what
happens when compiled for the Arduino. Also done for compatibility
reasons to @jgeisler0303 's Grbl simulator code.
- G-code parser will now ignore 'E' exponent values, since they are
reserved g-code characters for some machines. Thanks @csdexter!
- The read_double() function was re-written and optimized for use in
Grbl. The strtod() avr lib was removed.
- Added acceleration to the homing routine.
- Homing now accounts for different step rates when moving multiple
axes without exceeding acceleration limits.
- Homing now updates all internal positioning variables to machine zero
after completion.
- "Poor-man's" debounce delay added.
- Updated the delay_us() function to perform faster and more accurate
microsecond delays. Previously, the single increments would add
noticeable time drift for larger delays.
- Fix a bug in the stepper.c prescalar calculations that was changed in
the last commit.
- Other minor fixes.
- Updated makefile to be more universally compatible by not requiring
grep or ruby.
- Edited XON/XOFF flow control usage, noting that FTDI-based Arduinos
are known to work, but not Atmega8U2-based Arduino. Still officially
not supported, but added for advanced users.
- Minor edits.
- G54 work coordinate system support. Up to 6 work coordinate systems
(G54-G59) available as a compile-time option.
- G10 command added to set work coordinate offsets from machine
position.
- G92/G92.1 position offsets and cancellation support. Properly follows
NIST standard rules with other systems.
- G53 absolute override now works correctly with new coordinate systems.
- Revamped g-code parser with robust error checking. Providing user
feedback with bad commands. Follows NIST standards.
- Planner module slightly changed to only expected position movements
in terms of machine coordinates only. This was to simplify coordinate
system handling, which is done solely by the g-code parser.
- Upon grbl system abort, machine position and work positions are
retained, while G92 offsets are reset per NIST standards.
- Compiler compatibility update for _delay_us().
- Updated README.
- Grbl now tracks both home and work (G92) coordinate systems and does
live updates when G92 is called.
- Rudimentary home and work position status reporting. Works but still
under major construction.
- Updated the main streaming script. Has a disabled periodic timer for
querying status reports, disabled only because the Python timer doesn't
consistently restart after the script exits. Add here only for user
testing.
- Fixed a bug to prevent an endless serial_write loop during status
reports.
- Refactored the planner variables to make it more clear what they are
and make it easier for clear them.
- ALPHA status. - Multitasking ability with run-time command executions
for real-time control and feedback. - Decelerating feed hold and resume
during operation. - System abort/reset, which immediately kills all
movement and re-initializes grbl. - Re-structured grbl to easily allow
for new features: Status reporting, jogging, backlash compensation. (To
be completed in the following releases.) - Resized TX/RX serial buffers
(32/128 bytes) - Increased planner buffer size to 20 blocks. - Updated
documentation.
