- Minor bug fix for variable spindle PWM output. Values smaller than
the minimum RPM for the spindle would overflow the PWM value. Thanks
Rob!
- Created an optional minimum spindle PWM low-mark value as a
compile-time option. This is for special circumstances when the PWM has
to be at a certain level to be read by the spindle controller.
- Refactored the new probing commands (G38.3, G38.4, G38.5) code to
work better with the rest of Grbl’s systems.
- Refactored mc_probe() and mc_arc() to accept the mode of the command,
i.e. clockwise vs counter, toward vs away, etc. This is to make these
functions independent of gcode state variables.
- Removed the pull off motion in the probing cycle. This is not an
official operation and was added for user simplicity, but wrongly did
so. So bye bye.
- Created a configure probe invert mask function to handle the
different probe pin setting and probing cycle modes with a single mask.
- Minor bug fix with reporting motion modes via $G. G38.2 wasn’t
showing up. It now does, along with the other new probing commands.
- Refactored some of the new pin configurations for the future of Grbl.
-
This is likely the last major change to the v0.9 code base before push
to master. Only two minor things remain on the agenda (CoreXY support,
force clear EEPROM, and an extremely low federate bug).
- NEW! Grbl is now compile-able and may be flashed directly through the
Arduino IDE. Only minor changes were required for this compatibility.
See the Wiki to learn how to do it.
- New status reporting mask to turn on and off what Grbl sends back.
This includes machine coordinates, work coordinates, serial RX buffer
usage, and planner buffer usage. Expandable to more information on user
request, but that’s it for now.
- Settings have been completely renumbered to allow for future new
settings to be installed without having to constantly reshuffle and
renumber all of the settings every time.
- All settings masks have been standardized to mean bit 0 = X, bit 1 =
Y, and bit 2 = Z, to reduce confusion on how they work. The invert
masks used by the internal Grbl system were updated to accommodate this
change as well.
- New invert probe pin setting, which does what it sounds like.
- Fixed a probing cycle bug, where it would freeze intermittently, and
removed some redundant code.
- Homing may now be set to the origin wherever the limit switches are.
Traditionally machine coordinates should always be in negative space,
but when limit switches on are on the opposite side, the machine
coordinate would be set to -max_travel for the axis. Now you can always
make it [0,0,0] via a compile-time option in config.h. (Soft limits
routine was updated to account for this as well.)
- Probe coordinate message immediately after a probing cycle may now
be turned off via a compile-time option in config.h. By default the
probing location is always reported.
- Reduced the N_ARC_CORRECTION default value to reflect the changes in
how circles are generated by an arc tolerance, rather than a fixed arc
segment setting.
- Increased the incoming line buffer limit from 70 to 80 characters.
Had some extra memory space to invest into this.
- Fixed a bug where tool number T was not being tracked and reported
correctly.
- Added a print free memory function for debugging purposes. Not used
otherwise.
- Realtime rate report should now work during feed holds, but it hasn’t
been tested yet.
- Updated the streaming scripts with MIT-license and added the simple
streaming to the main stream.py script to allow for settings to be sent.
- Some minor code refactoring to improve flash efficiency. Reduced the
flash by several hundred KB, which was re-invested in some of these new
features.
- Pushed this uncompleted code to merge a conflicting pull request.
- New G43.1 and G49 g-codes to be installed. The beginnings of it are
in place. These g-codes are intended to be used in conjunction with
probing and allow GUIs to set tool length offsets without Grbl needing
to store a tool table.
- G43.1 is defined as a dynamic tool length offset that is not stored
in memory. Rather, when commanded, these are applied to the work
coordinates until a reset or disabled by G49. This works much like G92.
- Completely overhauled the g-code parser. It’s now 100%* compliant. (*
may have some bugs). Being compliant, here are some of the major
differences.
- SMALLER and JUST AS FAST! A number of optimizations were found that
sped things up and allowed for the more thorough error-checking to be
installed without a speed hit. Trimmed a lot of ‘fat’ in the parser and
still was able to make it significantly smaller than it was.
- No default feed rate setting! Removed completely! This doesn’t exist
in the g-code standard. So, it now errors out whenever it’s undefined
for motions that require it (G1/2/3/38.2).
- Any g-code parser error expunges the ENTIRE block. This means all
information is lost and not passed on to the running state. Before some
of the states would remain, which could have led to some problems.
- If the g-code block passes all of the error-checks, the g-code state
is updated and all motions are executed according to the order of
execution.
- Changes in spindle speed, when already running, will update the
output pin accordingly. This fixes a bug, where it wouldn’t update the
speed.
- Update g-code parser error reporting. Errors now return detailed
information of what exact went wrong. The most common errors return a
short text description. For less common errors, the parser reports
‘Invalid gcode ID:20’, where 20 is a error ID. A list of error code IDs
and their descriptions will be documented for user reference elsewhere
to save flash space.
- Other notable changes:
- Added a print integer routine for uint8 variables. This saved
significant flash space by switching from a heavier universal print
integer routine.
- Saved some flash space with our own short hypotenuse calculation
- Some arc computation flash and memory optimizations.
- G38.2 straight probe now supported. Rough draft. May be tweaked more
as testing ramps up.
- G38.2 requires at least one axis word. Multiple axis words work too.
When commanded, the probe cycle will move at the last ‘F’ feed rate
specified in a straight line.
- During a probe cycle: If the probe pin goes low (normal high), Grbl
will record that immediate position and engage a feed hold. Meaning
that the CNC machine will move a little past the probe switch point, so
keep federates low to stop sooner. Once stopped, Grbl will issue a move
to go back to the recorded probe trigger point.
- During a probe cycle: If the probe switch does not engage by the time
the machine has traveled to its target coordinates, Grbl will issue an
ALARM and the user will be forced to reset Grbl. (Currently G38.3 probe
without error isn’t supported, but would be easy to implement later.)
- After a successful probe, Grbl will send a feedback message
containing the recorded probe coordinates in the machine coordinate
system. This is as the g-code standard on probe parameters specifies.
- The recorded probe parameters are retained in Grbl memory and can be
viewed with the ‘$#’ print parameters command. Upon a power-cycle, not
a soft-reset, Grbl will re-zero these values.
- Moved ‘$#’ command to require IDLE or ALARM mode, because it accesses
EEPROM to fetch the coordinate system offsets.
- Updated the Grbl version to v0.9d.
- The probe cycle is subject to change upon testing or user-feedback.
WARNING: There are still some bugs to be worked out. Please use caution
if you test this firmware.
- Feed holds work much better, but there are still some failure
conditions that need to be worked out. This is the being worked on
currently and a fix is planned to be pushed next.
- Homing cycle refactoring: Slight adjustment of the homing cycle to
allow for limit pins to be shared by different axes, as long as the
shared limit pins are not homed on the same cycle. Also, removed the
LOCATE_CYCLE portion of the homing cycle configuration. It was
redundant.
- Limit pin sharing: (See above). To clear up one or two limit pins for
other IO, limit pins can now be shared. For example, the Z-limit can be
shared with either X or Y limit pins, because it’s on a separate homing
cycle. Hard limit will still work exactly as before.
- Spindle pin output fixed. The pins weren’t getting initialized
correctly.
- Fixed a cycle issue where streaming was working almost like a single
block mode. This was caused by a problem with the spindle_run() and
coolant_run() commands and issuing an unintended planner buffer sync.
- Refactored the cycle_start, feed_hold, and other runtime routines
into the runtime command module, where they should be handled here
only. These were redundant.
- Moved some function calls around into more appropriate source code
modules.
- Fixed the reporting of spindle state.
- Added a new source and header file called system. These files contain
the system commands and variables, as well as all of the system headers
and standard libraries Grbl uses. Centralizing some of the code.
- Re-organized the include headers throughout the source code.
- ENABLE_M7 define was missing from config.h. Now there.
- SPINDLE_MAX_RPM and SPINDLE_MIN_RPM now defined in config.h. No
uncommenting to prevent user issues. Minimum spindle RPM now provides
the lower, near 0V, scale adjustment, i.e. some spindles can go really
slow so why use up our 256 voltage bins for them?
- Remove some persistent variables from coolant and spindle control.
They were redundant.
- Removed a VARIABLE_SPINDLE define in cpu_map.h that shouldn’t have
been there.
- Changed the DEFAULT_ARC_TOLERANCE to 0.002mm to improve arc tracing.
Before we had issues with performance, no longer.
- Fixed a bug with the hard limits and the software debounce feature
enabled. The invert limit pin setting wasn’t honored.
- Fixed a bug with the homing direction mask. Now is like it used to
be. At least for now.
- Re-organized main.c to serve as only as the reset/initialization
routine. Makes things a little bit clearer in terms of execution
procedures.
- Re-organized protocol.c as the overall master control unit for
execution procedures. Not quite there yet, but starting to make a
little more sense in how things are run.
- Removed updating of old settings records. So many new settings have
been added that it’s not worth adding the code to migrate old user
settings.
- Tweaked spindle_control.c a bit and made it more clear and consistent
with other parts of Grbl.
- Tweaked the stepper disable bit code in stepper.c. Requires less
flash memory.
- Updated Grbl version to 0.9c and build number.
- G-code parser was missing modal group violation checks for M7/8/9
commands. Added them.
- Updated the Adaptive Multi-Axis Step Smoothing (AMASS) cutoff
frequencies so that the trade between the 16-bit Timer1 accuracy and
the level step smoothing are somewhat better balanced. (Smoothing isn’t
free, but a higher accuracy timer would provide high cutoff
frequencies.)
- Homing travel calculations fixed. It was computing the min travel
rather than max.
- Auto-start disable and pausing after spindle or dwell commands.
Related to plan_synchronize() function call. Now fixed, but still need
to work on the system state.
- Pushed a fix to make this branch more Arduino IDE compatible. Removed
extern call in nuts_bolts.c
- Updated the stepper configuration option of enabling or disabling the
new Adaptive Multi-Axis Step Smoothing Algorithm. Now works either way.
- Updated some copyright info.
- Maximum velocity for each axis is now configurable in settings. All
rapids/seek move at these maximums. All feed rates(including rapids)
may be limited and scaled down so that no axis does not exceed their
limits.
- Moved around auto-cycle start. May change later, but mainly to ensure
the planner buffer is completely full before cycle starting a streaming
program. Otherwise it should auto-start when there is a break in the
serial stream.
- Reverted old block->max_entry_speed_sqr calculations. Feedrate
overrides not close to ready at all.
- Fixed intermittent slow trailing steps for some triangle velocity
profile moves. The acceleration tick counter updating was corrected to
be exact for that particular transition. Should be ok for normal
trapezoidal profiles.
- Fixed the Timer0 disable after a step pulse falling edge. Thanks
@blinkenlight!
- Added Grbl state (Idle, Running, Queued, Hold, etc) to the real-time
status reporting feature as feedback to the user of what Grbl is doing.
Updated the help message to reflect this change.
- Removed switches (dry run, block delete, single block mode). To keep
Grbl simple and not muddled up from things that can easily be taken
care of by an external interface, these were removed.
- Check g-code mode was retained, but the command was moved to '$C'
from '$S0'.
- Fixed a minor issue where the seek rates would not immediately be
used and only would after a reset. Should update live now.
- A full circle IJ offset CCW arc would not do anything. Fixed bug via
a simple if-then statement.
- Radius mode tweaks to check for negative value in sqrt() rather than
isnan() it. Error report updated to indicate what actually happened.
- Removed the dry run switch. It was getting overly complicated for
what it needed to do. In practice, single block mode and feed rate
overrides (coming in next release) does a much better job with dry runs
than 'dry run'.
- Trimmed all of Grbl's messages from help, status, feedback to
settings. Saved 0.6KB+ of flash space that could be used for v0.9
features.
- Removed some settings inits when set. Will depend on user to power
cycle to get some of these to reload.
- Fixed a bug with settings version not re-writing old settings, when
it should. Thanks Alden!
- To make managing the code easier and to help ensure a user starts
with a fresh reset, the functionality of check g-code and dry run has
been changed to automatically perform a soft reset when toggled off.
Position will not be lost, unless there is a cycle active. Feed hold
before toggling off it needed.
This is mainly a safety issue. If a user dry runs a program and kills
it mid-program, and then restarts it thinking to run it as normal, the
g-code modes that we're set may not be what they expect, and very bad
things can happen.
- NOTE: Grbl is at 83.5% of flash capacity. Not a lot of room left, but
I think we can squeeze in some more!
- Added a purge buffer (and lock) command. This is an advanced option
to clear any queued blocks in the buffer in the event of system
position being lost or homed. These queued blocks will likely not move
correctly if not purged. In typical use, the purging command releases
the homing axes lock in case a user need to move the axes off their
hard limit switches, but position is not guaranteed. Homing is advised
immediately after.
- Created a system-wide sync current position function. Cleans up some
of the repetitive tasks in various places in the code that do the same
thing.
- Removed the clear all switches command '$S'. Not really needed and
helped clean up a sync call.
- Other minor tweaks. Readme updated slightly..
(All v0.8 features installed. Still likely buggy, but now thourough
testing will need to start to squash them all. As soon as we're done,
this will be pushed to master and v0.9 development will be started.
Please report ANY issues to us so we can get this rolled out ASAP.)
- User startup script! A user can now save one (up to 5 as compile-time
option) block of g-code in EEPROM memory. This will be run everytime
Grbl resets. Mainly to be used as a way to set your preferences, like
G21, G54, etc.
- New dry run and check g-code switches. Dry run moves ALL motions at
rapids rate ignoring spindle, coolant, and dwell commands. For rapid
physical proofing of your code. The check g-code switch ignores all
motion and provides the user a way to check if there are any errors in
their program that Grbl may not like.
- Program restart! (sort of). Program restart is typically an advanced
feature that allows users to restart a program mid-stream. The check
g-code switch can perform this feature by enabling the switch at the
start of the program, and disabling it at the desired point with some
minimal changes.
- New system state variable. This state variable tracks all of the
different state processes that Grbl performs, i.e. cycle start, feed
hold, homing, etc. This is mainly for making managing of these task
easier and more clear.
- Position lost state variable. Only when homing is enabled, Grbl will
refuse to move until homing is completed and position is known. This is
mainly for safety. Otherwise, it will let users fend for themselves.
- Moved the default settings defines into config.h. The plan is to
eventually create a set of config.h's for particular as-built machines
to help users from doing it themselves.
- Moved around misc defines into .h files. And lots of other little
things.
NOTE: Another incremental update. Likely buggy, still a ways to go
before everything is installed, such as startup blocks.
- Changed the '$' command to print help. '$$' now prints Grbl settings.
The help now instructs the user of runtime commands, switch toggling,
homing, etc. Jogging will be added to these in v0.9.
- Added switches: block delete, opt stop, and single block mode.
- Now can print the g-code parser state and persistent parameters
(coord sys) to view what Grbl has internally.
- Made the gc struct in the g-code parser global to be able to print
the states. Also moved coordinate system tracking from sys to gc struct.
- Changed up the welcome flag and updated version to v0.8c.
- Removed spindle speed from gcode parser. Not used.
- Added acceleration to the homing routine.
- Homing now accounts for different step rates when moving multiple
axes without exceeding acceleration limits.
- Homing now updates all internal positioning variables to machine zero
after completion.
- "Poor-man's" debounce delay added.
- Updated the delay_us() function to perform faster and more accurate
microsecond delays. Previously, the single increments would add
noticeable time drift for larger delays.
- Fix a bug in the stepper.c prescalar calculations that was changed in
the last commit.
- Other minor fixes.
- G54 work coordinate system support. Up to 6 work coordinate systems
(G54-G59) available as a compile-time option.
- G10 command added to set work coordinate offsets from machine
position.
- G92/G92.1 position offsets and cancellation support. Properly follows
NIST standard rules with other systems.
- G53 absolute override now works correctly with new coordinate systems.
- Revamped g-code parser with robust error checking. Providing user
feedback with bad commands. Follows NIST standards.
- Planner module slightly changed to only expected position movements
in terms of machine coordinates only. This was to simplify coordinate
system handling, which is done solely by the g-code parser.
- Upon grbl system abort, machine position and work positions are
retained, while G92 offsets are reset per NIST standards.
- Compiler compatibility update for _delay_us().
- Updated README.
- Program stop support (M0,M1*,M2,M30*). *Optional stop to be done.
*Pallet shuttle not supported.
- Work position is set equal to machine position upon reset, as
according to NIST RS274-NGC guidelines. G92 is disabled.
- Renamed mc_set_current_position() to mc_set_coordinate_offset().
- Fixed bug in plan_synchronize(). Would exit right before last step is
finished and caused issues with program stops. Now fixed.
- Spindle now stops upon a run-time abort command.
- Updated readme and misc upkeeping.
