This is likely the last major change to the v0.9 code base before push
to master. Only two minor things remain on the agenda (CoreXY support,
force clear EEPROM, and an extremely low federate bug).
- NEW! Grbl is now compile-able and may be flashed directly through the
Arduino IDE. Only minor changes were required for this compatibility.
See the Wiki to learn how to do it.
- New status reporting mask to turn on and off what Grbl sends back.
This includes machine coordinates, work coordinates, serial RX buffer
usage, and planner buffer usage. Expandable to more information on user
request, but that’s it for now.
- Settings have been completely renumbered to allow for future new
settings to be installed without having to constantly reshuffle and
renumber all of the settings every time.
- All settings masks have been standardized to mean bit 0 = X, bit 1 =
Y, and bit 2 = Z, to reduce confusion on how they work. The invert
masks used by the internal Grbl system were updated to accommodate this
change as well.
- New invert probe pin setting, which does what it sounds like.
- Fixed a probing cycle bug, where it would freeze intermittently, and
removed some redundant code.
- Homing may now be set to the origin wherever the limit switches are.
Traditionally machine coordinates should always be in negative space,
but when limit switches on are on the opposite side, the machine
coordinate would be set to -max_travel for the axis. Now you can always
make it [0,0,0] via a compile-time option in config.h. (Soft limits
routine was updated to account for this as well.)
- Probe coordinate message immediately after a probing cycle may now
be turned off via a compile-time option in config.h. By default the
probing location is always reported.
- Reduced the N_ARC_CORRECTION default value to reflect the changes in
how circles are generated by an arc tolerance, rather than a fixed arc
segment setting.
- Increased the incoming line buffer limit from 70 to 80 characters.
Had some extra memory space to invest into this.
- Fixed a bug where tool number T was not being tracked and reported
correctly.
- Added a print free memory function for debugging purposes. Not used
otherwise.
- Realtime rate report should now work during feed holds, but it hasn’t
been tested yet.
- Updated the streaming scripts with MIT-license and added the simple
streaming to the main stream.py script to allow for settings to be sent.
- Some minor code refactoring to improve flash efficiency. Reduced the
flash by several hundred KB, which was re-invested in some of these new
features.
- Added a new optional compile-time feature for ‘realtime’ (within
50ms) feed rate reporting. When querying for a status report, a new
data value will state the current operating rate. It’s only beta at the
moment and has some kinks to work out.
- Updated the code for printing floating point values to N decimal
places. Generalized the main floating point print code to accept a new
decimal places value and created a set of handler functions to print
certain floating point value types used in Grbl, like position, rates,
coordinate offsets, etc. All of these have different decimal
requirements and change when printed in mm or inches mode.
- Number of decimal places for the different value types can be
re-defined in config.h, but there shouldn’t be a need for this, as
these are physically limited.
- Removed the decimal places settings, as this was now obsoleted by the
new decimal places code.
- The new decimal places code also saves almost 300kB in flash space,
as it’s more efficient.
- Completely overhauled the g-code parser. It’s now 100%* compliant. (*
may have some bugs). Being compliant, here are some of the major
differences.
- SMALLER and JUST AS FAST! A number of optimizations were found that
sped things up and allowed for the more thorough error-checking to be
installed without a speed hit. Trimmed a lot of ‘fat’ in the parser and
still was able to make it significantly smaller than it was.
- No default feed rate setting! Removed completely! This doesn’t exist
in the g-code standard. So, it now errors out whenever it’s undefined
for motions that require it (G1/2/3/38.2).
- Any g-code parser error expunges the ENTIRE block. This means all
information is lost and not passed on to the running state. Before some
of the states would remain, which could have led to some problems.
- If the g-code block passes all of the error-checks, the g-code state
is updated and all motions are executed according to the order of
execution.
- Changes in spindle speed, when already running, will update the
output pin accordingly. This fixes a bug, where it wouldn’t update the
speed.
- Update g-code parser error reporting. Errors now return detailed
information of what exact went wrong. The most common errors return a
short text description. For less common errors, the parser reports
‘Invalid gcode ID:20’, where 20 is a error ID. A list of error code IDs
and their descriptions will be documented for user reference elsewhere
to save flash space.
- Other notable changes:
- Added a print integer routine for uint8 variables. This saved
significant flash space by switching from a heavier universal print
integer routine.
- Saved some flash space with our own short hypotenuse calculation
- Some arc computation flash and memory optimizations.
- Added a new source and header file called system. These files contain
the system commands and variables, as well as all of the system headers
and standard libraries Grbl uses. Centralizing some of the code.
- Re-organized the include headers throughout the source code.
- ENABLE_M7 define was missing from config.h. Now there.
- SPINDLE_MAX_RPM and SPINDLE_MIN_RPM now defined in config.h. No
uncommenting to prevent user issues. Minimum spindle RPM now provides
the lower, near 0V, scale adjustment, i.e. some spindles can go really
slow so why use up our 256 voltage bins for them?
- Remove some persistent variables from coolant and spindle control.
They were redundant.
- Removed a VARIABLE_SPINDLE define in cpu_map.h that shouldn’t have
been there.
- Changed the DEFAULT_ARC_TOLERANCE to 0.002mm to improve arc tracing.
Before we had issues with performance, no longer.
- Fixed a bug with the hard limits and the software debounce feature
enabled. The invert limit pin setting wasn’t honored.
- Fixed a bug with the homing direction mask. Now is like it used to
be. At least for now.
- Re-organized main.c to serve as only as the reset/initialization
routine. Makes things a little bit clearer in terms of execution
procedures.
- Re-organized protocol.c as the overall master control unit for
execution procedures. Not quite there yet, but starting to make a
little more sense in how things are run.
- Removed updating of old settings records. So many new settings have
been added that it’s not worth adding the code to migrate old user
settings.
- Tweaked spindle_control.c a bit and made it more clear and consistent
with other parts of Grbl.
- Tweaked the stepper disable bit code in stepper.c. Requires less
flash memory.
- Homing travel calculations fixed. It was computing the min travel
rather than max.
- Auto-start disable and pausing after spindle or dwell commands.
Related to plan_synchronize() function call. Now fixed, but still need
to work on the system state.
- Pushed a fix to make this branch more Arduino IDE compatible. Removed
extern call in nuts_bolts.c
- Updated the stepper configuration option of enabling or disabling the
new Adaptive Multi-Axis Step Smoothing Algorithm. Now works either way.
- Updated some copyright info.
(All v0.8 features installed. Still likely buggy, but now thourough
testing will need to start to squash them all. As soon as we're done,
this will be pushed to master and v0.9 development will be started.
Please report ANY issues to us so we can get this rolled out ASAP.)
- User startup script! A user can now save one (up to 5 as compile-time
option) block of g-code in EEPROM memory. This will be run everytime
Grbl resets. Mainly to be used as a way to set your preferences, like
G21, G54, etc.
- New dry run and check g-code switches. Dry run moves ALL motions at
rapids rate ignoring spindle, coolant, and dwell commands. For rapid
physical proofing of your code. The check g-code switch ignores all
motion and provides the user a way to check if there are any errors in
their program that Grbl may not like.
- Program restart! (sort of). Program restart is typically an advanced
feature that allows users to restart a program mid-stream. The check
g-code switch can perform this feature by enabling the switch at the
start of the program, and disabling it at the desired point with some
minimal changes.
- New system state variable. This state variable tracks all of the
different state processes that Grbl performs, i.e. cycle start, feed
hold, homing, etc. This is mainly for making managing of these task
easier and more clear.
- Position lost state variable. Only when homing is enabled, Grbl will
refuse to move until homing is completed and position is known. This is
mainly for safety. Otherwise, it will let users fend for themselves.
- Moved the default settings defines into config.h. The plan is to
eventually create a set of config.h's for particular as-built machines
to help users from doing it themselves.
- Moved around misc defines into .h files. And lots of other little
things.
- printFloat() function execution doubled in speed. This is a precursor
to status reporting, since GUIs may query real-time position rapidly.
- Decimal places added to settings (for now). This may disappear in
future pushes, but here for testing purposes.
- Limit pin internal pull-resistors now enabled. Normal high operation.
This will be the standard going forward.
- Updated all of the 'double' variable types to 'float' to reflect what
happens when compiled for the Arduino. Also done for compatibility
reasons to @jgeisler0303 's Grbl simulator code.
- G-code parser will now ignore 'E' exponent values, since they are
reserved g-code characters for some machines. Thanks @csdexter!
- The read_double() function was re-written and optimized for use in
Grbl. The strtod() avr lib was removed.
- Program stop support (M0,M1*,M2,M30*). *Optional stop to be done.
*Pallet shuttle not supported.
- Work position is set equal to machine position upon reset, as
according to NIST RS274-NGC guidelines. G92 is disabled.
- Renamed mc_set_current_position() to mc_set_coordinate_offset().
- Fixed bug in plan_synchronize(). Would exit right before last step is
finished and caused issues with program stops. Now fixed.
- Spindle now stops upon a run-time abort command.
- Updated readme and misc upkeeping.
- Added machine position reporting to status queries. This will be
further developed with part positioning/offsets and maintaining
location upon reset.
- System variables refactored into a global struct for better
readability.
- Removed old obsolete Ruby streaming scripts. These were no longer
compatible. Updated Python streaming scripts.
- Fixed printFloat() and other printing functions.
- Decreased planner buffer back to 18 blocks and increased TX serial
buffer to 64 bytes. Need the memory space for future developments.
- Begun adding run-time modes to grbl, where block delete toggle, mm/in
reporting modes, jog modes, etc can be set during runtime. Will be
fleshed out and placed into EEPROM when everything is added.
