ManuelW/grbl-LPC-CoreXY
1
0
Fork 0
Code Issues Pull Requests Releases 1 Wiki Activity

Delete a new work file shouldn't have been synced.

Browse Source
This commit is contained in:
Sonny Jeon 2011-10-11 21:00:06 -06:00
parent 9141ad2825
commit 169c859b9c
1 changed files with 0 additions and 207 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

207
motion_control_new.c
View File

@ -1,207 +0,0 @@
/*
motion_control.c - high level interface for issuing motion commands
Part of Grbl
Copyright (c) 2009-2011 Simen Svale Skogsrud
Copyright (c) 2011 Sungeun K. Jeon
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
#include <avr/io.h>
#include "settings.h"
#include "config.h"
#include "motion_control.h"
#include <util/delay.h>
#include <math.h>
#include <stdlib.h>
#include "nuts_bolts.h"
#include "stepper.h"
#include "planner.h"
// Execute dwell in seconds. Maximum time delay is > 18 hours, more than enough for any application.
void mc_dwell(double seconds)
{
uint16_t i = floor(seconds);
st_synchronize();
_delay_ms(floor(1000*(seconds-i))); // Delay millisecond remainder
while (i > 0) {
_delay_ms(1000); // Delay one second
i--;
}
}
// void mc_jog_enable()
// {
// // Planned sequence of events:
// // Send X,Y,Z motion, target step rate, direction
// // Rate_delta, step_xyz, counter_xyz should be all the same.
// //
// Change of direction can cause some problems. Need to force a complete stop for any direction change.
// This likely needs to be done in stepper.c as a jog mode parameter.
// !!! Need a way to get step locations realtime!!!
// Jog is a specialized case, where grbl is reset and there is no cycle start.
// If there is a real-time status elsewhere, this shouldn't be a problem.
// st.direction_bits = current_block->direction_bits;
// st.target_rate;
// st.rate_delta;
// st.step_event_count;
// st.steps_x;
// st.steps_y;
// st.steps_z;
// st.counter_x = -(current_block->step_event_count >> 1);
// st.counter_y = st.counter_x;
// st.counter_z = st.counter_x;
// st.step_event_count = current_block->step_event_count;
// st.step_events_completed = 0;
// }
// void mc_jog_disable()
// {
// // Calls stepper.c and disables jog mode to start deceleration.
// // Shouldn't have to anything else. Just initiate the stop, so if re-enabled, it can accelerate.
// }
// void mc_feed_hold()
// {
// // Planned sequence of events:
// // Query stepper for interrupting cycle and hold until pause flag is set?
// // Query stepper intermittenly and check for !st.do_motion to indicate complete stop.
// // Retreive st.step_events_completed and recompute current location.
// // Truncate current block start to current location.
// // Re-plan buffer for start from zero velocity and truncated block length.
// // All necessary computations for a restart should be done by now.
// // Reset pause flag.
// // Only wait for a cycle start command from user interface. (TBD).
// // !!! Need to check how to circumvent the wait in the main program. May need to be in serial.c
// // as an interrupt process call. Can two interrupt programs exist at the same time??
// }
// Execute an arc in offset mode format. position == current xyz, target == target xyz,
// offset == offset from current xyz, axis_XXX defines circle plane in tool space, axis_linear is
// the direction of helical travel, radius == circle radius, isclockwise boolean. Used
// for vector transformation direction.
// position, target, and offset are pointers to vectors from gcode.c
#ifdef __AVR_ATmega328P__
// The arc is approximated by generating a huge number of tiny, linear segments. The length of each
// segment is configured in settings.mm_per_arc_segment.
void mc_arc(double *position, double *target, double *offset, uint8_t axis_0, uint8_t axis_1,
uint8_t axis_linear, double feed_rate, uint8_t invert_feed_rate, double radius, uint8_t isclockwise)
{
// int acceleration_manager_was_enabled = plan_is_acceleration_manager_enabled();
// plan_set_acceleration_manager_enabled(false); // disable acceleration management for the duration of the arc
double center_axis0 = position[axis_0] + offset[axis_0];
double center_axis1 = position[axis_1] + offset[axis_1];
double linear_travel = target[axis_linear] - position[axis_linear];
double r_axis0 = -offset[axis_0]; // Radius vector from center to current location
double r_axis1 = -offset[axis_1];
double rt_axis0 = target[axis_0] - center_axis0;
double rt_axis1 = target[axis_1] - center_axis1;
// CCW angle between position and target from circle center. Only one atan2() trig computation required.
double angular_travel = atan2(r_axis0*rt_axis1-r_axis1*rt_axis0, r_axis0*rt_axis0+r_axis1*rt_axis1);
if (angular_travel < 0) { angular_travel += 2*M_PI; }
if (isclockwise) { angular_travel -= 2*M_PI; }
double millimeters_of_travel = hypot(angular_travel*radius, fabs(linear_travel));
if (millimeters_of_travel == 0.0) { return; }
uint16_t segments = floor(millimeters_of_travel/settings.mm_per_arc_segment);
// Multiply inverse feed_rate to compensate for the fact that this movement is approximated
// by a number of discrete segments. The inverse feed_rate should be correct for the sum of
// all segments.
if (invert_feed_rate) { feed_rate *= segments; }
double theta_per_segment = angular_travel/segments;
double linear_per_segment = linear_travel/segments;
/* Vector rotation by transformation matrix: r is the original vector, r_T is the rotated vector,
and phi is the angle of rotation. Based on the solution approach by Jens Geisler.
r_T = [cos(phi) -sin(phi);
sin(phi) cos(phi] * r ;
For arc generation, the center of the circle is the axis of rotation and the radius vector is
defined from the circle center to the initial position. Each line segment is formed by successive
vector rotations. This requires only two cos() and sin() computations to form the rotation
matrix for the duration of the entire arc. Error may accumulate from numerical round-off, since
all double numbers are single precision on the Arduino. (True double precision will not have
round off issues for CNC applications.) Single precision error can accumulate to be greater than
tool precision in some cases. Therefore, arc path correction is implemented.
Small angle approximation may be used to reduce computation overhead further. This approximation
holds for everything, but very small circles and large mm_per_arc_segment values. In other words,
theta_per_segment would need to be greater than 0.1 rad and N_ARC_CORRECTION would need to be large
to cause an appreciable drift error. N_ARC_CORRECTION~=25 is more than small enough to correct for
numerical drift error. N_ARC_CORRECTION may be on the order a hundred(s) before error becomes an
issue for CNC machines with the single precision Arduino calculations.
This approximation also allows mc_arc to immediately insert a line segment into the planner
without the initial overhead of computing cos() or sin(). By the time the arc needs to be applied
a correction, the planner should have caught up to the lag caused by the initial mc_arc overhead.
This is important when there are successive arc motions.
*/
// Vector rotation matrix values
double cos_T = 1-0.5*theta_per_segment*theta_per_segment; // Small angle approximation
double sin_T = theta_per_segment;
double arc_target[3];
double sin_Ti;
double cos_Ti;
double r_axisi;
uint16_t i;
int8_t count = 0;
// Initialize the linear axis
arc_target[axis_linear] = position[axis_linear];
for (i = 1; i<segments; i++) { // Increment (segments-1)
if (count < N_ARC_CORRECTION) {
// Apply vector rotation matrix
r_axisi = r_axis0*sin_T + r_axis1*cos_T;
r_axis0 = r_axis0*cos_T - r_axis1*sin_T;
r_axis1 = r_axisi;
count++;
} else {
// Arc correction to radius vector. Computed only every N_ARC_CORRECTION increments.
// Compute exact location by applying transformation matrix from initial radius vector(=-offset).
cos_Ti = cos(i*theta_per_segment);
sin_Ti = sin(i*theta_per_segment);
r_axis0 = -offset[axis_0]*cos_Ti + offset[axis_1]*sin_Ti;
r_axis1 = -offset[axis_0]*sin_Ti - offset[axis_1]*cos_Ti;
count = 0;
}
// Update arc_target location
arc_target[axis_0] = center_axis0 + r_axis0;
arc_target[axis_1] = center_axis1 + r_axis1;
arc_target[axis_linear] += linear_per_segment;
plan_buffer_line(arc_target[X_AXIS], arc_target[Y_AXIS], arc_target[Z_AXIS], feed_rate, invert_feed_rate);
}
// Ensure last segment arrives at target location.
plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], feed_rate, invert_feed_rate);
// plan_set_acceleration_manager_enabled(acceleration_manager_was_enabled);
}
#endif
void mc_go_home()
{
st_go_home();
}