grbl-LPC-CoreXY/settings.h

101 lines
3.7 KiB
C
Raw Normal View History

2009-01-25 00:48:56 +01:00
/*
settings.h - eeprom configuration handling
2009-01-25 00:48:56 +01:00
Part of Grbl
Copyright (c) 2009-2011 Simen Svale Skogsrud
Copyright (c) 2011-2012 Sungeun K. Jeon
2009-01-25 00:48:56 +01:00
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
2011-02-05 00:45:41 +01:00
#ifndef settings_h
#define settings_h
2009-01-25 00:48:56 +01:00
#include <math.h>
#include "nuts_bolts.h"
2009-01-25 00:48:56 +01:00
#define GRBL_VERSION "0.9a"
// Version of the EEPROM data. Will be used to migrate existing data from older versions of Grbl
// when firmware is upgraded. Always stored in byte 0 of eeprom
#define SETTINGS_VERSION 52
// Define bit flag masks for the boolean settings in settings.flag.
#define BITFLAG_REPORT_INCHES bit(0)
#define BITFLAG_AUTO_START bit(1)
#define BITFLAG_INVERT_ST_ENABLE bit(2)
#define BITFLAG_HARD_LIMIT_ENABLE bit(3)
#define BITFLAG_HOMING_ENABLE bit(4)
// Define EEPROM memory address location values for Grbl settings and parameters
// NOTE: The Atmega328p has 1KB EEPROM. The upper half is reserved for parameters and
// the startup script. The lower half contains the global settings and space for future
// developments.
#define EEPROM_ADDR_GLOBAL 1
#define EEPROM_ADDR_PARAMETERS 512
New startup script setting. New dry run, check gcode switches. New system state variable. Lots of reorganizing. (All v0.8 features installed. Still likely buggy, but now thourough testing will need to start to squash them all. As soon as we're done, this will be pushed to master and v0.9 development will be started. Please report ANY issues to us so we can get this rolled out ASAP.) - User startup script! A user can now save one (up to 5 as compile-time option) block of g-code in EEPROM memory. This will be run everytime Grbl resets. Mainly to be used as a way to set your preferences, like G21, G54, etc. - New dry run and check g-code switches. Dry run moves ALL motions at rapids rate ignoring spindle, coolant, and dwell commands. For rapid physical proofing of your code. The check g-code switch ignores all motion and provides the user a way to check if there are any errors in their program that Grbl may not like. - Program restart! (sort of). Program restart is typically an advanced feature that allows users to restart a program mid-stream. The check g-code switch can perform this feature by enabling the switch at the start of the program, and disabling it at the desired point with some minimal changes. - New system state variable. This state variable tracks all of the different state processes that Grbl performs, i.e. cycle start, feed hold, homing, etc. This is mainly for making managing of these task easier and more clear. - Position lost state variable. Only when homing is enabled, Grbl will refuse to move until homing is completed and position is known. This is mainly for safety. Otherwise, it will let users fend for themselves. - Moved the default settings defines into config.h. The plan is to eventually create a set of config.h's for particular as-built machines to help users from doing it themselves. - Moved around misc defines into .h files. And lots of other little things.
2012-11-03 18:32:23 +01:00
#define EEPROM_ADDR_STARTUP_BLOCK 768
// Define EEPROM address indexing for coordinate parameters
#define N_COORDINATE_SYSTEM 6 // Number of supported work coordinate systems (from index 1)
#define SETTING_INDEX_NCOORD N_COORDINATE_SYSTEM+1 // Total number of system stored (from index 0)
// NOTE: Work coordinate indices are (0=G54, 1=G55, ... , 6=G59)
#define SETTING_INDEX_G28 N_COORDINATE_SYSTEM // Home position 1
#define SETTING_INDEX_G30 N_COORDINATE_SYSTEM+1 // Home position 2
// #define SETTING_INDEX_G92 N_COORDINATE_SYSTEM+2 // Coordinate offset (G92.2,G92.3 not supported)
// Global persistent settings (Stored from byte EEPROM_ADDR_GLOBAL onwards)
typedef struct {
float steps_per_mm[N_AXIS];
uint8_t microsteps;
uint8_t pulse_microseconds;
float default_feed_rate;
float default_seek_rate;
uint8_t invert_mask;
float arc_tolerance;
float acceleration[N_AXIS];
float junction_deviation;
uint8_t flags; // Contains default boolean settings
uint8_t homing_dir_mask;
float homing_feed_rate;
float homing_seek_rate;
uint16_t homing_debounce_delay;
float homing_pulloff;
uint8_t stepper_idle_lock_time; // If max value 255, steppers do not disable.
uint8_t decimal_places;
float max_velocity[N_AXIS];
// float mm_soft_limit[N_AXIS];
// uint8_t status_report_mask; // Mask to indicate desired report data.
} settings_t;
extern settings_t settings;
// Initialize the configuration subsystem (load settings from EEPROM)
2011-02-05 00:45:41 +01:00
void settings_init();
// A helper method to set new settings from command line
uint8_t settings_store_global_setting(int parameter, float value);
2009-01-25 00:48:56 +01:00
New startup script setting. New dry run, check gcode switches. New system state variable. Lots of reorganizing. (All v0.8 features installed. Still likely buggy, but now thourough testing will need to start to squash them all. As soon as we're done, this will be pushed to master and v0.9 development will be started. Please report ANY issues to us so we can get this rolled out ASAP.) - User startup script! A user can now save one (up to 5 as compile-time option) block of g-code in EEPROM memory. This will be run everytime Grbl resets. Mainly to be used as a way to set your preferences, like G21, G54, etc. - New dry run and check g-code switches. Dry run moves ALL motions at rapids rate ignoring spindle, coolant, and dwell commands. For rapid physical proofing of your code. The check g-code switch ignores all motion and provides the user a way to check if there are any errors in their program that Grbl may not like. - Program restart! (sort of). Program restart is typically an advanced feature that allows users to restart a program mid-stream. The check g-code switch can perform this feature by enabling the switch at the start of the program, and disabling it at the desired point with some minimal changes. - New system state variable. This state variable tracks all of the different state processes that Grbl performs, i.e. cycle start, feed hold, homing, etc. This is mainly for making managing of these task easier and more clear. - Position lost state variable. Only when homing is enabled, Grbl will refuse to move until homing is completed and position is known. This is mainly for safety. Otherwise, it will let users fend for themselves. - Moved the default settings defines into config.h. The plan is to eventually create a set of config.h's for particular as-built machines to help users from doing it themselves. - Moved around misc defines into .h files. And lots of other little things.
2012-11-03 18:32:23 +01:00
// Stores the protocol line variable as a startup line in EEPROM
void settings_store_startup_line(uint8_t n, char *line);
// Reads an EEPROM startup line to the protocol line variable
uint8_t settings_read_startup_line(uint8_t n, char *line);
// Writes selected coordinate data to EEPROM
void settings_write_coord_data(uint8_t coord_select, float *coord_data);
// Reads selected coordinate data from EEPROM
uint8_t settings_read_coord_data(uint8_t coord_select, float *coord_data);
2009-01-25 00:48:56 +01:00
#endif