add missing constants from upstream pybambu module

update pybambu module from upstream HA project

octoprint_bambu_printer/printer/bambu_virtual_printer.py

@@ -259,19 +259,20 @@ class BambuVirtualPrinter:
             f"connecting via local mqtt: {self._settings.get_boolean(['local_mqtt'])}"
         )
         bambu_client = BambuClient(
-            device_type=self._settings.get(["device_type"]),
-            serial=self._settings.get(["serial"]),
-            host=self._settings.get(["host"]),
-            username=(
+            {"device_type": self._settings.get(["device_type"]),
+            "serial": self._settings.get(["serial"]),
+            "host": self._settings.get(["host"]),
+            "username": (
                 "bblp"
                 if self._settings.get_boolean(["local_mqtt"])
                 else self._settings.get(["username"])
             ),
-            access_code=self._settings.get(["access_code"]),
-            local_mqtt=self._settings.get_boolean(["local_mqtt"]),
-            region=self._settings.get(["region"]),
-            email=self._settings.get(["email"]),
-            auth_token=self._settings.get(["auth_token"]) if self._settings.get_boolean(["local_mqtt"]) is False else "",
+            "access_code": self._settings.get(["access_code"]),
+            "local_mqtt": self._settings.get_boolean(["local_mqtt"]),
+            "region": self._settings.get(["region"]),
+            "email": self._settings.get(["email"]),
+            "auth_token": self._settings.get(["auth_token"]) if self._settings.get_boolean(["local_mqtt"]) is False else "",
+             }
         )
         bambu_client.on_disconnect = self.on_disconnect(bambu_client.on_disconnect)
         bambu_client.on_connect = self.on_connect(bambu_client.on_connect)

octoprint_bambu_printer/printer/pybambu/bambu_client.py

@@ -181,7 +181,7 @@ class ChamberImageThread(threading.Thread):
 
                                 # Reset buffer
                                 img = None
-                            # else:
+                            # else:     
                             # Otherwise we need to continue looping without reseting the buffer to receive the remaining data
                             # and without delaying.
 
@@ -237,7 +237,7 @@ class MqttThread(threading.Thread):
         exceptionSeen = ""
         while True:
             try:
-                host = self._client.host if self._client.local_mqtt else self._client.bambu_cloud.cloud_mqtt_host
+                host = self._client.host if self._client._local_mqtt else self._client.bambu_cloud.cloud_mqtt_host
                 LOGGER.debug(f"Connect: Attempting Connection to {host}")
                 self._client.client.connect(host, self._client._port, keepalive=5)
 
@@ -285,25 +285,32 @@ class BambuClient:
     _camera = None
     _usage_hours: float
 
-    def __init__(self, device_type: str, serial: str, host: str, local_mqtt: bool, region: str, email: str,
-                 username: str, auth_token: str, access_code: str, usage_hours: float = 0, manual_refresh_mode: bool = False, chamber_image: bool = True):
-        self.callback = None
-        self.host = host
-        self.local_mqtt = local_mqtt
-        self._serial = serial
-        self._auth_token = auth_token
-        self._access_code = access_code
-        self._username = username
+    def __init__(self, config):
+        self.host = config['host']
+        self._callback = None
+
+        self._access_code = config.get('access_code', '')
+        self._auth_token = config.get('auth_token', '')
+        self._device_type = config.get('device_type', 'unknown')
+        self._local_mqtt = config.get('local_mqtt', False)
+        self._manual_refresh_mode = config.get('manual_refresh_mode', False)
+        self._serial = config.get('serial', '')
+        self._usage_hours = config.get('usage_hours', 0)
+        self._username = config.get('username', '')
+        self._enable_camera = config.get('enable_camera', True)
+
         self._connected = False
-        self._device_type = device_type
-        self._usage_hours = usage_hours
         self._port = 1883
         self._refreshed = False
-        self._manual_refresh_mode = manual_refresh_mode
+
         self._device = Device(self)
-        self.bambu_cloud = BambuCloud(region, email, username, auth_token)
+        self.bambu_cloud = BambuCloud(
+            config.get('region', ''),
+            config.get('email', ''),
+            config.get('username', ''),
+            config.get('auth_token', '')
+        )
         self.slicer_settings = SlicerSettings(self)
-        self.use_chamber_image = chamber_image
 
     @property
     def connected(self):
@@ -322,7 +329,22 @@ class BambuClient:
             self.disconnect()
         else:
             # Reconnect normally
-            self.connect(self.callback)
+            self.connect(self._callback)
+
+    @property
+    def camera_enabled(self):
+        return self._enable_camera
+    
+    def callback(self, event: str):
+        if self._callback is not None:
+            self._callback(event)
+
+    def set_camera_enabled(self, enable):
+        self._enable_camera = enable
+        if self._enable_camera:
+            self._start_camera()
+        else:
+            self._stop_camera()
 
     def setup_tls(self):
         self.client.tls_set(tls_version=ssl.PROTOCOL_TLS, cert_reqs=ssl.CERT_NONE)
@@ -331,7 +353,7 @@ class BambuClient:
     def connect(self, callback):
         """Connect to the MQTT Broker"""
         self.client = mqtt.Client()
-        self.callback = callback
+        self._callback = callback
         self.client.on_connect = self.on_connect
         self.client.on_disconnect = self.on_disconnect
         self.client.on_message = self.on_message
@@ -342,7 +364,7 @@ class BambuClient:
         self.setup_tls()
 
         self._port = 8883
-        if self.local_mqtt:
+        if self._local_mqtt:
             self.client.username_pw_set("bblp", password=self._access_code)
         else:
             self.client.username_pw_set(self._username, password=self._auth_token)
@@ -371,6 +393,22 @@ class BambuClient:
         LOGGER.info("On Connect: Connected to printer")
         self._on_connect()
 
+    def _start_camera(self):
+        if not self._device.supports_feature(Features.CAMERA_RTSP):
+            if self._device.supports_feature(Features.CAMERA_IMAGE):
+                if self._enable_camera:
+                    LOGGER.debug("Starting Chamber Image thread")
+                    self._camera = ChamberImageThread(self)
+                    self._camera.start()
+            elif (self.host == "") or (self._access_code == ""):
+                LOGGER.debug("Skipping camera setup as local access details not provided.")
+
+    def _stop_camera(self):
+        if self._camera is not None:
+            LOGGER.debug("Stopping camera thread")
+            self._camera.stop()
+            self._camera.join()
+
     def _on_connect(self):
         self._connected = True
         self.subscribe_and_request_info()
@@ -379,14 +417,7 @@ class BambuClient:
         self._watchdog = WatchdogThread(self)
         self._watchdog.start()
 
-        if not self._device.supports_feature(Features.CAMERA_RTSP):
-            if self._device.supports_feature(Features.CAMERA_IMAGE):
-                if self.use_chamber_image:
-                    LOGGER.debug("Starting Chamber Image thread")
-                    self._camera = ChamberImageThread(self)
-                    self._camera.start()
-            elif (self.host == "") or (self._access_code == ""):
-                LOGGER.debug("Skipping camera setup as local access details not provided.")
+        self._start_camera()
 
     def try_on_connect(self,
                        client_: mqtt.Client,
@@ -410,7 +441,7 @@ class BambuClient:
         """Called when MQTT Disconnects"""
         LOGGER.warn(f"On Disconnect: Printer disconnected with error code: {result_code}")
         self._on_disconnect()
-
+    
     def _on_disconnect(self):
         LOGGER.debug("_on_disconnect: Lost connection to the printer")
         self._connected = False
@@ -419,10 +450,7 @@ class BambuClient:
             LOGGER.debug("Stopping watchdog thread")
             self._watchdog.stop()
             self._watchdog.join()
-        if self._camera is not None:
-            LOGGER.debug("Stopping camera thread")
-            self._camera.stop()
-            self._camera.join()
+        self._stop_camera()
 
     def _on_watchdog_fired(self):
         LOGGER.info("Watch dog fired")
@@ -487,7 +515,7 @@ class BambuClient:
         """Force refresh data"""
 
         if self._manual_refresh_mode:
-            self.connect(self.callback)
+            self.connect(self._callback)
         else:
             LOGGER.debug("Force Refresh: Getting Version Info")
             self._refreshed = True
@@ -531,8 +559,8 @@ class BambuClient:
         # Run the blocking tls_set method in a separate thread
         loop = asyncio.get_event_loop()
         await loop.run_in_executor(None, self.setup_tls)
-
-        if self.local_mqtt:
+        
+        if self._local_mqtt:
             self.client.username_pw_set("bblp", password=self._access_code)
         else:
             self.client.username_pw_set(self._username, password=self._auth_token)

octoprint_bambu_printer/printer/pybambu/bambu_cloud.py

@@ -1,13 +1,27 @@
 from __future__ import annotations
+from enum import (
+    Enum,
+)
 
 import base64
+import cloudscraper
 import json
+import requests
 
-curl_available = True
-try:
-    from curl_cffi import requests as curl_requests
-except ImportError:
-    curl_available = False
+class ConnectionMechanismEnum(Enum):
+    CLOUDSCRAPER = 1,
+    CURL_CFFI = 2,
+    REQUESTS = 3
+
+CONNECTION_MECHANISM = ConnectionMechanismEnum.CLOUDSCRAPER
+
+curl_available = False
+if CONNECTION_MECHANISM == ConnectionMechanismEnum.CURL_CFFI:
+    try:
+        from curl_cffi import requests as curl_requests
+        curl_available = True
+    except ImportError:
+        curl_available = False
 
 from dataclasses import dataclass
 
@@ -20,6 +34,36 @@ from .utils import get_Url
 
 IMPERSONATE_BROWSER='chrome'
 
+class CloudflareError(Exception):
+    def __init__(self):
+        super().__init__("Blocked by Cloudflare")
+        self.error_code = 403
+
+class EmailCodeRequiredError(Exception):
+    def __init__(self):
+        super().__init__("Email code required")
+        self.error_code = 400
+
+class EmailCodeExpiredError(Exception):
+    def __init__(self):
+        super().__init__("Email code expired")
+        self.error_code = 400
+
+class EmailCodeIncorrectError(Exception):
+    def __init__(self):
+        super().__init__("Email code incorrect")
+        self.error_code = 400
+
+class TfaCodeRequiredError(Exception):
+    def __init__(self):
+        super().__init__("Two factor authentication code required")
+        self.error_code = 400
+
+class CurlUnavailableError(Exception):
+    def __init__(self):
+        super().__init__("curl library unavailable")
+        self.error_code = 400
+
 @dataclass
 class BambuCloud:
   
@@ -30,16 +74,101 @@ class BambuCloud:
         self._auth_token = auth_token
         self._tfaKey = None
 
+    def _get_headers(self):
+        return {
+            'User-Agent': 'bambu_network_agent/01.09.05.01',
+            'X-BBL-Client-Name': 'OrcaSlicer',
+            'X-BBL-Client-Type': 'slicer',
+            'X-BBL-Client-Version': '01.09.05.51',
+            'X-BBL-Language': 'en-US',
+            'X-BBL-OS-Type': 'linux',
+            'X-BBL-OS-Version': '6.2.0',
+            'X-BBL-Agent-Version': '01.09.05.01',
+            'X-BBL-Executable-info': '{}',
+            'X-BBL-Agent-OS-Type': 'linux',
+            'accept': 'application/json',
+            'Content-Type': 'application/json'
+        }
+        # Orca/Bambu Studio also add this - need to work out what an appropriate ID is to put here:
+        # 'X-BBL-Device-ID': BBL_AUTH_UUID,
+        # Example: X-BBL-Device-ID: 370f9f43-c6fe-47d7-aec9-5fe5ef7e7673
+
     def _get_headers_with_auth_token(self) -> dict:
-        headers = {}
+        if CONNECTION_MECHANISM == ConnectionMechanismEnum.CURL_CFFI:
+            headers = {}
+        else:
+            headers = self._get_headers()
         headers['Authorization'] = f"Bearer {self._auth_token}"
         return headers
-    
-    def _get_authentication_token(self) -> dict:
+
+    def _test_response(self, response, return400=False):
+        # Check specifically for cloudflare block
+        if response.status_code == 403 and 'cloudflare' in response.text:
+            LOGGER.debug("BLOCKED BY CLOUDFLARE")
+            raise CloudflareError()
+
+        if response.status_code == 400 and not return400:
+            LOGGER.error(f"Connection failed with error code: {response.status_code}")
+            LOGGER.debug(f"Response: '{response.text}'")
+            raise PermissionError(response.status_code, response.text)
+
+        if response.status_code > 400:
+            LOGGER.error(f"Connection failed with error code: {response.status_code}")
+            LOGGER.debug(f"Response: '{response.text}'")
+            raise PermissionError(response.status_code, response.text)
+
+        LOGGER.debug(f"Response: {response.status_code}")
+
+    def _get(self, urlenum: BambuUrl):
+        url = get_Url(urlenum, self._region)
+        headers=self._get_headers_with_auth_token()
+        if CONNECTION_MECHANISM == ConnectionMechanismEnum.CURL_CFFI:
+            if not curl_available:
+                LOGGER.debug(f"Curl library is unavailable.")
+                raise CurlUnavailableError()
+            response = curl_requests.get(url, headers=headers, timeout=10, impersonate=IMPERSONATE_BROWSER)
+        elif CONNECTION_MECHANISM == ConnectionMechanismEnum.CLOUDSCRAPER:
+            if len(headers) == 0:
+                headers = self._get_headers()
+            scraper = cloudscraper.create_scraper()
+            response = scraper.get(url, headers=headers, timeout=10)
+        elif CONNECTION_MECHANISM == ConnectionMechanismEnum.REQUESTS:
+            if len(headers) == 0:
+                headers = self._get_headers()
+            response = requests.get(url, headers=headers, timeout=10)
+        else:
+            raise NotImplementedError()
+
+        self._test_response(response)
+
+        return response
+
+
+    def _post(self, urlenum: BambuUrl, json: str, headers={}, return400=False):
+        url = get_Url(urlenum, self._region)
+        if CONNECTION_MECHANISM == ConnectionMechanismEnum.CURL_CFFI:
+            if not curl_available:
+                LOGGER.debug(f"Curl library is unavailable.")
+                raise CurlUnavailableError()
+            response = curl_requests.post(url, headers=headers, json=json, impersonate=IMPERSONATE_BROWSER)
+        elif CONNECTION_MECHANISM == ConnectionMechanismEnum.CLOUDSCRAPER:
+            if len(headers) == 0:
+                headers = self._get_headers()
+            scraper = cloudscraper.create_scraper()
+            response = scraper.post(url, headers=headers, json=json)
+        elif CONNECTION_MECHANISM == ConnectionMechanismEnum.REQUESTS:
+            if len(headers) == 0:
+                headers = self._get_headers()
+            response = requests.post(url, headers=headers, json=json)
+        else:
+            raise NotImplementedError()
+
+        self._test_response(response, return400)
+        
+        return response
+
+    def _get_authentication_token(self) -> str:
         LOGGER.debug("Getting accessToken from Bambu Cloud")
-        if not curl_available:
-            LOGGER.debug(f"Curl library is unavailable.")
-            return 'curlUnavailable'
 
         # First we need to find out how Bambu wants us to login.
         data = {
@@ -48,20 +177,7 @@ class BambuCloud:
             "apiError": ""
         }
 
-        response = curl_requests.post(get_Url(BambuUrl.LOGIN, self._region), json=data, impersonate=IMPERSONATE_BROWSER)
-
-        # Check specifically for cloudflare block
-        if response.status_code == 403:
-            if 'cloudflare' in response.text:
-                LOGGER.error('CloudFlare blocked connection attempt')
-                return 'cloudFlare'
-            
-        if response.status_code >= 400:
-            LOGGER.error(f"Login attempt failed with error code: {response.status_code}")
-            LOGGER.debug(f"Response: '{response.text}'")
-            raise ValueError(response.status_code)
-
-        LOGGER.debug(f"Response: {response.status_code}")
+        response = self._post(BambuUrl.LOGIN, json=data)
 
         auth_json = response.json()
         accessToken = auth_json.get('accessToken', '')
@@ -73,18 +189,19 @@ class BambuCloud:
         if loginType is None:
             LOGGER.error(f"loginType not present")
             LOGGER.error(f"Response not understood: '{response.text}'")
-            return None
+            return ValueError(0) # FIXME
         elif loginType == 'verifyCode':
             LOGGER.debug(f"Received verifyCode response")
+            raise EmailCodeRequiredError()
         elif loginType == 'tfa':
             # Store the tfaKey for later use
             LOGGER.debug(f"Received tfa response")
             self._tfaKey = auth_json.get("tfaKey")
+            raise TfaCodeRequiredError()
         else:
             LOGGER.debug(f"Did not understand json. loginType = '{loginType}'")
             LOGGER.error(f"Response not understood: '{response.text}'")
-
-        return loginType
+            return ValueError(1) # FIXME
     
     def _get_email_verification_code(self):
         # Send the verification code request
@@ -94,14 +211,8 @@ class BambuCloud:
         }
 
         LOGGER.debug("Requesting verification code")
-        response = curl_requests.post(get_Url(BambuUrl.EMAIL_CODE, self._region), json=data, impersonate=IMPERSONATE_BROWSER)
-        
-        if response.status_code == 200:
-            LOGGER.debug("Verification code requested successfully.")
-        else:
-            LOGGER.error(f"Received error trying to send verification code: {response.status_code}")
-            LOGGER.debug(f"Response: '{response.text}'")
-            raise ValueError(response.status_code)
+        self._post(BambuUrl.EMAIL_CODE, json=data)
+        LOGGER.debug("Verification code requested successfully.")
 
     def _get_authentication_token_with_verification_code(self, code) -> dict:
         LOGGER.debug("Attempting to connect with provided verification code.")
@@ -110,27 +221,24 @@ class BambuCloud:
             "code": code
         }
 
-        response = curl_requests.post(get_Url(BambuUrl.LOGIN, self._region), json=data, impersonate=IMPERSONATE_BROWSER)
+        response = self._post(BambuUrl.LOGIN, json=data, return400=True)
+        status_code = response.status_code
 
-        LOGGER.debug(f"Response: {response.status_code}")
-        if response.status_code == 200:
+        if status_code == 200:
             LOGGER.debug("Authentication successful.")
-        elif response.status_code == 400:
-            LOGGER.debug(f"Response: '{response.json()}'")
+            LOGGER.debug(f"Response = '{response.json()}'")
+        elif status_code == 400:
+            LOGGER.debug(f"Received response: {response.json()}")           
             if response.json()['code'] == 1:
                 # Code has expired. Request a new one.
                 self._get_email_verification_code()
-                return 'codeExpired'
+                raise EmailCodeExpiredError()
             elif response.json()['code'] == 2:
                 # Code was incorrect. Let the user try again.
-                return 'codeIncorrect'
+                raise EmailCodeIncorrectError()
             else:
                 LOGGER.error(f"Response not understood: '{response.json()}'")
                 raise ValueError(response.json()['code'])
-        else:
-            LOGGER.error(f"Received error trying to authenticate with verification code: {response.status_code}")
-            LOGGER.debug(f"Response: '{response.text}'")
-            raise ValueError(response.status_code)
 
         return response.json()['accessToken']
     
@@ -142,30 +250,57 @@ class BambuCloud:
             "tfaCode": code
         }
 
-        response = curl_requests.post(get_Url(BambuUrl.TFA_LOGIN, self._region), json=data, impersonate=IMPERSONATE_BROWSER)
+        response = self._post(BambuUrl.TFA_LOGIN, json=data)
 
         LOGGER.debug(f"Response: {response.status_code}")
         if response.status_code == 200:
             LOGGER.debug("Authentication successful.")
-        else:
-            LOGGER.error(f"Received error trying to authenticate with verification code: {response.status_code}")
-            LOGGER.debug(f"Response: '{response.text}'")
-            raise ValueError(response.status_code)
 
         cookies = response.cookies.get_dict()
         token_from_tfa = cookies.get("token")
-        LOGGER.debug(f"token_from_tfa: {token_from_tfa}")
+        #LOGGER.debug(f"token_from_tfa: {token_from_tfa}")
 
         return token_from_tfa
     
     def _get_username_from_authentication_token(self) -> str:
+        LOGGER.debug("Trying to get username from authentication token.")
         # User name is in 2nd portion of the auth token (delimited with periods)
-        b64_string = self._auth_token.split(".")[1]
-        # String must be multiples of 4 chars in length. For decode pad with = character
-        b64_string += "=" * ((4 - len(b64_string) % 4) % 4)
-        jsonAuthToken = json.loads(base64.b64decode(b64_string))
-        # Gives json payload with "username":"u_<digits>" within it
-        return jsonAuthToken['username']
+        username = None
+        tokens = self._auth_token.split(".")
+        if len(tokens) != 3:
+            LOGGER.debug("Received authToken is not a JWT.")
+            LOGGER.debug("Trying to use project API to retrieve username instead")
+            response = self.get_projects();
+            if response is not None:
+                projectsnode = response.get('projects', None)
+                if projectsnode is None:
+                    LOGGER.debug("Failed to find projects node")
+                else:
+                    if len(projectsnode) == 0:
+                        LOGGER.debug("No projects node in response")
+                    else:
+                        project=projectsnode[0]
+                        if project.get('user_id', None) is None:
+                            LOGGER.debug("No user_id entry")
+                        else:
+                            username = f"u_{project['user_id']}"
+                            LOGGER.debug(f"Found user_id of {username}")
+        else:
+            LOGGER.debug("Authentication token looks to be a JWT")
+            try:
+                b64_string = self._auth_token.split(".")[1]
+                # String must be multiples of 4 chars in length. For decode pad with = character
+                b64_string += "=" * ((4 - len(b64_string) % 4) % 4)
+                jsonAuthToken = json.loads(base64.b64decode(b64_string))
+                # Gives json payload with "username":"u_<digits>" within it
+                username = jsonAuthToken.get('username', None)
+            except:
+                LOGGER.debug("Unable to decode authToken to json to retrieve username.")
+
+        if username is None:
+            LOGGER.debug(f"Unable to decode authToken to retrieve username. AuthToken = {self._auth_token}")
+
+        return username
     
     # Retrieves json description of devices in the form:
     # {
@@ -182,7 +317,7 @@ class BambuCloud:
     #             'dev_product_name': 'P1S',
     #             'dev_access_code': 'REDACTED',
     #             'nozzle_diameter': 0.4
-    #             },
+    #         },
     #         {
     #             'dev_id': 'REDACTED',
     #             'name': 'Bambu P1P',
@@ -192,7 +327,7 @@ class BambuCloud:
     #             'dev_product_name': 'P1P',
     #             'dev_access_code': 'REDACTED',
     #             'nozzle_diameter': 0.4
-    #             },
+    #         },
     #         {
     #             'dev_id': 'REDACTED',
     #             'name': 'Bambu X1C',
@@ -202,7 +337,7 @@ class BambuCloud:
     #             'dev_product_name': 'X1 Carbon',
     #             'dev_access_code': 'REDACTED',
     #             'nozzle_diameter': 0.4
-    #             }
+    #         }
     #     ]
     # }
     
@@ -223,49 +358,25 @@ class BambuCloud:
         self._password = password
 
         result = self._get_authentication_token()
-        if result is None:
-            LOGGER.error("Unable to authenticate.")
-            return None
-        elif len(result) < 20:
-            return result
-        else:
-            self._auth_token = result
-            self._username = self._get_username_from_authentication_token()
-            return 'success'
+        self._auth_token = result
+        self._username = self._get_username_from_authentication_token()
         
     def login_with_verification_code(self, code: str):
         result = self._get_authentication_token_with_verification_code(code)
-        if len(result) < 20:
-            return result
         self._auth_token = result
         self._username = self._get_username_from_authentication_token()
-        return 'success'
 
     def login_with_2fa_code(self, code: str):
         result = self._get_authentication_token_with_2fa_code(code)
-        if len(result) < 20:
-            return result
         self._auth_token = result
         self._username = self._get_username_from_authentication_token()
-        return 'success'
 
     def get_device_list(self) -> dict:
         LOGGER.debug("Getting device list from Bambu Cloud")
-        if not curl_available:
-            LOGGER.debug(f"Curl library is unavailable.")
-            raise None
-        
-        response = curl_requests.get(get_Url(BambuUrl.BIND, self._region), headers=self._get_headers_with_auth_token(), timeout=10, impersonate=IMPERSONATE_BROWSER)
-        if response.status_code == 403:
-            if 'cloudflare' in response.text:
-                LOGGER.error('CloudFlare blocked connection attempt')
-            raise ValueError(response.status_code)
-
-        if response.status_code >= 400:
-            LOGGER.debug(f"Received error: {response.status_code}")
-            LOGGER.error(f"Received error: '{response.text}'")
-            raise ValueError(response.status_code)
-        
+        try:
+            response = self._get(BambuUrl.BIND)
+        except:
+            return None
         return response.json()['devices']
 
     # The slicer settings are of the following form:
@@ -336,23 +447,13 @@ class BambuCloud:
     # }
 
     def get_slicer_settings(self) -> dict:
-        LOGGER.debug("DISABLED: Getting slicer settings from Bambu Cloud")
-        # Disabled for now since it may be contributing to cloudflare detection speed.
-        # 
-        # if curl_available:
-        #     response = curl_requests.get(get_Url(BambuUrl.SLICER_SETTINGS, self._region), headers=self._get_headers_with_auth_token(), timeout=10, impersonate=IMPERSONATE_BROWSER)
-        #     if response.status_code == 403:
-        #         if 'cloudflare' in response.text:
-        #             LOGGER.error(f"Cloudflare blocked slicer settings lookup.")
-        #             return None
-                
-        #     if response.status_code >= 400:
-        #         LOGGER.error(f"Slicer settings load failed: {response.status_code}")
-        #         LOGGER.error(f"Slicer settings load failed: '{response.text}'")
-        #         return None
-            
-        #     return response.json()
-        return None
+        LOGGER.debug("Getting slicer settings from Bambu Cloud")
+        try:
+            response = self._get(BambuUrl.SLICER_SETTINGS)
+        except:
+            return None
+        LOGGER.debug("Succeeded")
+        return response.json()
         
     # The task list is of the following form with a 'hits' array with typical 20 entries.
     #
@@ -398,28 +499,37 @@ class BambuCloud:
 
     def get_tasklist(self) -> dict:
         LOGGER.debug("Getting full task list from Bambu Cloud")
-        if not curl_available:
-            LOGGER.debug(f"Curl library is unavailable.")
-            raise None
-        
-        url = get_Url(BambuUrl.TASKS, self._region)
-        response = curl_requests.get(url, headers=self._get_headers_with_auth_token(), timeout=10, impersonate=IMPERSONATE_BROWSER)
-        if response.status_code == 403:
-            if 'cloudflare' in response.text:
-                LOGGER.error('CloudFlare blocked connection attempt')
-                return None
-
-        # Check specifically for cloudflare block
-        if response.status_code == 403:
-            if 'cloudflare' in response.text:
-                LOGGER.error('CloudFlare blocked connection attempt')
-                return None
-
-        if response.status_code >= 400:
-            LOGGER.debug(f"Received error: {response.status_code}")
-            LOGGER.debug(f"Received error: '{response.text}'")
-            raise None
+        try:
+            response = self._get(BambuUrl.TASKS)
+        except:
+            return None
+        return response.json()
 
+    # Returns a list of projects for the account.
+    #
+    # {
+    # "message": "success",
+    # "code": null,
+    # "error": null,
+    # "projects": [
+    #     {
+    #     "project_id": "164995388",
+    #     "user_id": "1688388450",
+    #     "model_id": "US48e2103d939bf8",
+    #     "status": "ACTIVE",
+    #     "name": "Alcohol_Marker_Storage_for_Copic,_Ohuhu_and_the_like",
+    #     "content": "{'printed_plates': [{'plate': 1}]}",
+    #     "create_time": "2024-11-17 06:12:33",
+    #     "update_time": "2024-11-17 06:12:40"
+    #     },
+    #     ...
+    #
+    def get_projects(self) -> dict:
+        LOGGER.debug("Getting projects list from Bambu Cloud")
+        try:
+            response = self._get(BambuUrl.PROJECTS)
+        except:
+            return None
         return response.json()
 
     def get_latest_task_for_printer(self, deviceId: str) -> dict:
@@ -429,11 +539,9 @@ class BambuCloud:
             if len(data) != 0:
                 return data[0]
             LOGGER.debug("No tasks found for printer")
-        except:
-            LOGGER.debug("Unable to make call")
             return None
-            
-        return None
+        except:
+            return None
 
     def get_tasklist_for_printer(self, deviceId: str) -> dict:
         LOGGER.debug(f"Getting full task list for printer from Bambu Cloud")
@@ -451,21 +559,11 @@ class BambuCloud:
 
     def download(self, url: str) -> bytearray:
         LOGGER.debug(f"Downloading cover image: {url}")
-        if not curl_available:
-            LOGGER.debug(f"Curl library is unavailable.")
+        try:
+            # This is just a standard download from an unauthenticated end point.
+            response = requests.get(url)
+        except:
             return None
-
-        response = curl_requests.get(url, timeout=10, impersonate=IMPERSONATE_BROWSER)
-        if response.status_code == 403:
-            if 'cloudflare' in response.text:
-                LOGGER.error('CloudFlare blocked connection attempt')
-                raise ValueError(response.status_code)
-
-        if response.status_code >= 400:
-            LOGGER.debug(f"Received error: {response.status_code}")
-            LOGGER.debug(f"Received error: {response.text}")
-            raise ValueError(response.status_code)
-        
         return response.content
 
     @property

octoprint_bambu_printer/printer/pybambu/const_ams_errors.py

@@ -0,0 +1,386 @@
+HMS_AMS_ERRORS = {
+    "0700_0100_0001_0001": "The AMS A assist motor has slipped. The extrusion wheel may be worn down, or the filament may be too thin.",
+    "0700_0100_0001_0003": "The AMS A assist motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0700_0100_0001_0004": "The AMS A assist motor speed control is malfunctioning. The speed sensor may be faulty.",
+    "0700_0100_0001_0011": "AMS A The assist motor calibration parameter error. Please pull out the filament from the filament hub and then restart the AMS.",
+    "0700_0100_0002_0002": "The AMS A assist motor is overloaded. The filament may be tangled or stuck.",
+    "0700_0200_0001_0001": "AMS A Filament speed and length error: The filament odometry may be faulty.",
+    "0700_1000_0001_0001": "The AMS A slot1 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0700_1000_0001_0003": "The AMS A slot1 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0700_1000_0002_0002": "The AMS A slot1 motor is overloaded. The filament may be tangled or stuck.",
+    "0700_1100_0001_0001": "The AMS A slot2 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0700_1100_0001_0003": "The AMS A slot2 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0700_1100_0002_0002": "The AMS A slot2 motor is overloaded. The filament may be tangled or stuck.",
+    "0700_1200_0001_0001": "The AMS A slot3 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0700_1200_0001_0003": "The AMS A slot3 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0700_1200_0002_0002": "The AMS A slot3 motor is overloaded. The filament may be tangled or stuck.",
+    "0700_1300_0001_0001": "The AMS A slot4 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0700_1300_0001_0003": "The AMS A slot4 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0700_1300_0002_0002": "The AMS A slot4 motor is overloaded. The filament may be tangled or stuck.",
+    "0700_2000_0002_0001": "AMS A Slot1 filament has run out. Please insert a new filament.",
+    "0700_2000_0002_0002": "AMS A Slot1 is empty; please insert a new filament.",
+    "0700_2000_0002_0003": "AMS A Slot1's filament may be broken in AMS.",
+    "0700_2000_0002_0004": "AMS A Slot1 filament may be broken in the tool head.",
+    "0700_2000_0002_0005": "AMS A Slot1 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0700_2000_0002_0006": "PTFE tube detached during the feeding process. Please check if the PTFE tube is connected to the AMS and extruder.",
+    "0700_2000_0003_0001": "AMS A Slot1 filament has run out. Please wait while old filament is purged.",
+    "0700_2000_0003_0002": "AMS A Slot1 filament has run out and automatically switched to the slot with the same filament.",
+    "0700_2100_0002_0001": "AMS A Slot2 filament has run out. Please insert a new filament.",
+    "0700_2100_0002_0002": "AMS A Slot2 is empty; please insert a new filament.",
+    "0700_2100_0002_0003": "AMS A Slot2's filament may be broken in AMS.",
+    "0700_2100_0002_0004": "AMS A Slot2 filament may be broken in the tool head.",
+    "0700_2100_0002_0005": "AMS A Slot2 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0700_2100_0003_0001": "AMS A Slot2 filament has run out. Please wait while old filament is purged.",
+    "0700_2100_0003_0002": "AMS A Slot2 filament has run out and automatically switched to the slot with the same filament.",
+    "0700_2200_0002_0001": "AMS A Slot3 filament has run out. Please insert a new filament.",
+    "0700_2200_0002_0002": "AMS A Slot3 is empty; please insert a new filament.",
+    "0700_2200_0002_0003": "AMS A Slot3's filament may be broken in AMS.",
+    "0700_2200_0002_0004": "AMS A Slot3 filament may be broken in the tool head.",
+    "0700_2200_0002_0005": "AMS A Slot3 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0700_2200_0003_0001": "AMS A Slot3 filament has run out. Please wait while old filament is purged.",
+    "0700_2200_0003_0002": "AMS A Slot3 filament has run out and automatically switched to the slot with the same filament.",
+    "0700_2300_0002_0001": "AMS A Slot4 filament has run out. Please insert a new filament.",
+    "0700_2300_0002_0002": "AMS A Slot4 is empty; please insert a new filament.",
+    "0700_2300_0002_0003": "AMS A Slot4's filament may be broken in AMS.",
+    "0700_2300_0002_0004": "AMS A Slot4 filament may be broken in the tool head.",
+    "0700_2300_0002_0005": "AMS A Slot4 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0700_2300_0003_0001": "AMS A Slot4 filament has run out. Please wait while old filament is purged.",
+    "0700_2300_0003_0002": "AMS A Slot4 filament has run out and automatically switched to the slot with the same filament.",
+    "0700_3000_0001_0001": "The AMS A RFID 0 board has an error.",
+    "0700_3000_0001_0004": "Encryption chip failure.",
+    "0700_3000_0002_0002": "The RFID-tag on AMS A Slot1 is damaged or the it's content cannot be identified.",
+    "0700_3000_0003_0003": "RFID cannot be read because of a hardware or structural error.",
+    "0700_3100_0001_0001": "The AMS A RFID 1 board has an error.",
+    "0700_3100_0001_0004": "Encryption chip failure.",
+    "0700_3100_0002_0002": "The RFID-tag on AMS A Slot2 is damaged or the it's content cannot be identified.",
+    "0700_3100_0003_0003": "RFID cannot be read because of a hardware or structural error.",
+    "0700_3200_0002_0002": "The RFID-tag on AMS A Slot3 is damaged or the it's content cannot be identified.",
+    "0700_3300_0002_0002": "The RFID-tag on AMS A Slot4 is damaged or the it's content cannot be identified.",
+    "0700_3500_0001_0001": "The temperature and humidity sensor has an error. The chip may be faulty.",
+    "0700_3500_0001_0002": "AMS A The humidity sensor is disconnected, which may due to poor connector contact.",
+    "0700_4000_0002_0001": "The filament buffer position signal lost: the cable or position sensor may be malfunctioning.",
+    "0700_4000_0002_0002": "The filament buffer position signal error: the position sensor may be malfunctioning.",
+    "0700_4000_0002_0003": "The AMS Hub communication is abnormal, the cable may be not well connected.",
+    "0700_4000_0002_0004": "The filament buffer signal is abnormal; the spring may be stuck or the filament may be tangle.",
+    "0700_4500_0002_0001": "The filament cutter sensor is malfunctioning; please check whether the connector is properly plugged in.",
+    "0700_4500_0002_0002": "The filament cutter's cutting distance is too large. The XY motor may lose steps.",
+    "0700_4500_0002_0003": "The filament cutter handle has not been released. The handle or blade may be jammed, or there could be an issue with the filament sensor connection.",
+    "0700_5000_0002_0001": "AMS A communication is abnormal; please check the connection cable.",
+    "0700_5100_0003_0001": "The AMS is disabled; please load filament from spool holder.",
+    "0700_6000_0002_0001": "The AMS A slot1 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0700_6100_0002_0001": "The AMS A slot2 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0700_6200_0002_0001": "The AMS A slot3 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0700_6300_0002_0001": "The AMS A slot4 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0700_7000_0002_0001": "Failed to pull out the filament from the extruder. Possible causes: clogged extruder or broken filament. Refer to the Assistant for details.",
+    "0700_7000_0002_0002": "Failed to feed filament into the toolhead. Possible cause: filament or spool stuck. Please refer to the Assistant for details.",
+    "0700_7000_0002_0003": "Failed to extrude the filament. Possible cause: extruder or nozzle clogged. Please refer to the Assistant for details.",
+    "0700_7000_0002_0004": "Failed to pull back the filament from the toolhead to AMS. Possible cause: filament or spool stuck. Please refer to the Assistant for details.",
+    "0700_7000_0002_0005": "Failed to feed the filament outside the AMS. Please clip the end of the filament flat and check to see if the spool is stuck. Please refer to the Assistant for details.",
+    "0700_7000_0002_0006": "Timeout purging old filament. Possible cause: filament stuck or extruder/nozzle clogged. Please refer to the Assistant for details.",
+    "0700_7000_0002_0007": "AMS filament ran out. Please put a new filament into AMS and click the 'Retry' button.",
+    "0700_7000_0002_0008": "Failed to get AMS mapping table; please click 'Resume' to retry",
+    "0700_7000_0002_0030": "",
+    "0700_7000_0002_0031": "",
+    "0700_7000_0002_0032": "",
+    "0700_7000_0002_0033": "",
+    "0700_7000_0002_0040": "",
+    "0700_7000_0002_0041": "",
+    "0700_7000_0002_0042": "",
+    "0700_7000_0002_0043": "",
+    "0700_7000_0002_0044": "",
+    "0700_7000_0002_0045": "",
+    "0700_7000_0002_0046": "",
+    "0700_7000_0002_0050": "",
+    "0700_7000_0002_0060": "",
+    "0700_7000_0002_0061": "",
+    "0700_8000_0001_0002": "AMS A The heater 1 is disconnected, which may due to poor connector contact.",
+    "0700_8100_0001_0002": "AMS A The heater 2 is disconnected, which may due to poor connector contact.",
+    "0700_9200_0001_0001": "AMS A The cooling fan of heater 1 is blocked, which may be due to the fan being stuck.",
+    "0700_9200_0002_0002": "AMS A The cooling fan speed of heater 1 is too low, which could be due to excessive fan resistance.",
+    "0700_9300_0001_0001": "AMS A The cooling fan of heater 2 is blocked, which may be due to the fan being stuck.",
+    "0700_9300_0002_0002": "AMS A The cooling fan speed of heater 2 is too low, which could be due to excessive fan resistance.",
+    "0700_9400_0001_0001": "AMS A The temperature sensor of heater 1 is malfunctioning, , which may due to poor connector contact.",
+    "0700_9500_0001_0001": "AMS A The temperature sensor of heater 2 is malfunctioning, , which may due to poor connector contact.",
+    "0701_0100_0001_0001": "The AMS B assist motor has slipped. The extrusion wheel may be worn down, or the filament may be too thin.",
+    "0701_0100_0001_0003": "The AMS B assist motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0701_0100_0001_0004": "The AMS B assist motor speed control is malfunctioning. The speed sensor may be faulty.",
+    "0701_0100_0001_0011": "AMS B The assist motor calibration parameter error. Please pull out the filament from the filament hub and then restart the AMS.",
+    "0701_0100_0002_0002": "The AMS B assist motor is overloaded. The filament may be tangled or stuck.",
+    "0701_0200_0001_0001": "AMS B Filament speed and length error: The filament odometry may be faulty.",
+    "0701_1000_0001_0001": "The AMS B slot1 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0701_1000_0001_0003": "The AMS B slot1 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0701_1000_0002_0002": "The AMS B slot1 motor is overloaded. The filament may be tangled or stuck.",
+    "0701_1100_0001_0001": "The AMS B slot2 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0701_1100_0001_0003": "The AMS B slot2 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0701_1100_0002_0002": "The AMS B slot2 motor is overloaded. The filament may be tangled or stuck.",
+    "0701_1200_0001_0001": "The AMS B slot3 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0701_1200_0001_0003": "The AMS B slot3 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0701_1200_0002_0002": "The AMS B slot3 motor is overloaded. The filament may be tangled or stuck.",
+    "0701_1300_0001_0001": "The AMS B slot4 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0701_1300_0001_0003": "The AMS B slot4 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0701_1300_0002_0002": "The AMS B slot4 motor is overloaded. The filament may be tangled or stuck.",
+    "0701_2000_0002_0001": "AMS B Slot1 filament has run out. Please insert a new filament.",
+    "0701_2000_0002_0002": "AMS B Slot1 is empty; please insert a new filament.",
+    "0701_2000_0002_0003": "AMS B Slot1's filament may be broken in AMS.",
+    "0701_2000_0002_0004": "AMS B Slot1 filament may be broken in the tool head.",
+    "0701_2000_0002_0005": "AMS B Slot1 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0701_2000_0002_0006": "PTFE tube detached during the feeding process. Please check if the PTFE tube is connected to the AMS and extruder.",
+    "0701_2000_0003_0001": "AMS B Slot1 filament has run out. Please wait while old filament is purged.",
+    "0701_2000_0003_0002": "AMS B Slot1 filament has run out and automatically switched to the slot with the same filament.",
+    "0701_2100_0002_0001": "AMS B Slot2 filament has run out. Please insert a new filament.",
+    "0701_2100_0002_0002": "AMS B Slot2 is empty; please insert a new filament.",
+    "0701_2100_0002_0003": "AMS B Slot2's filament may be broken in AMS.",
+    "0701_2100_0002_0004": "AMS B Slot2 filament may be broken in the tool head.",
+    "0701_2100_0002_0005": "AMS B Slot2 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0701_2100_0003_0001": "AMS B Slot2 filament has run out. Please wait while old filament is purged.",
+    "0701_2100_0003_0002": "AMS B Slot2 filament has run out and automatically switched to the slot with the same filament.",
+    "0701_2200_0002_0001": "AMS B Slot3 filament has run out. Please insert a new filament.",
+    "0701_2200_0002_0002": "AMS B Slot3 is empty; please insert a new filament.",
+    "0701_2200_0002_0003": "AMS B Slot3's filament may be broken in AMS.",
+    "0701_2200_0002_0004": "AMS B Slot3 filament may be broken in the tool head.",
+    "0701_2200_0002_0005": "AMS B Slot3 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0701_2200_0003_0001": "AMS B Slot3 filament has run out. Please wait while old filament is purged.",
+    "0701_2200_0003_0002": "AMS B Slot3 filament has run out and automatically switched to the slot with the same filament.",
+    "0701_2300_0002_0001": "AMS B Slot4 filament has run out. Please insert a new filament.",
+    "0701_2300_0002_0002": "AMS B Slot4 is empty; please insert a new filament.",
+    "0701_2300_0002_0003": "AMS B Slot4's filament may be broken in AMS.",
+    "0701_2300_0002_0004": "AMS B Slot4 filament may be broken in the tool head.",
+    "0701_2300_0002_0005": "AMS B Slot4 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0701_2300_0003_0001": "AMS B Slot4 filament has run out. Please wait while old filament is purged.",
+    "0701_2300_0003_0002": "AMS B Slot4 filament has run out and automatically switched to the slot with the same filament.",
+    "0701_3000_0001_0001": "The AMS B RFID 0 board has an error.",
+    "0701_3000_0001_0004": "Encryption chip failure.",
+    "0701_3000_0002_0002": "The RFID-tag on AMS B Slot1 is damaged or the it's content cannot be identified.",
+    "0701_3000_0003_0003": "RFID cannot be read because of a hardware or structural error.",
+    "0701_3100_0001_0001": "The AMS B RFID 1 board has an error.",
+    "0701_3100_0001_0004": "Encryption chip failure.",
+    "0701_3100_0002_0002": "The RFID-tag on AMS B Slot2 is damaged or the it's content cannot be identified.",
+    "0701_3100_0003_0003": "RFID cannot be read because of a hardware or structural error.",
+    "0701_3200_0002_0002": "The RFID-tag on AMS B Slot3 is damaged or the it's content cannot be identified.",
+    "0701_3300_0002_0002": "The RFID-tag on AMS B Slot4 is damaged or the it's content cannot be identified.",
+    "0701_3500_0001_0001": "The temperature and humidity sensor has an error. The chip may be faulty.",
+    "0701_3500_0001_0002": "AMS B The humidity sensor is disconnected, which may due to poor connector contact.",
+    "0701_5000_0002_0001": "AMS B communication is abnormal; please check the connection cable.",
+    "0701_6000_0002_0001": "The AMS B slot1 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0701_6100_0002_0001": "The AMS B slot2 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0701_6200_0002_0001": "The AMS B slot3 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0701_6300_0002_0001": "The AMS B slot4 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0701_7000_0002_0001": "Failed to pull out the filament from the extruder. Possible causes: clogged extruder or broken filament. Refer to the Assistant for details.",
+    "0701_7000_0002_0002": "Failed to feed the filament into the toolhead. Possible cause: filament or spool stuck. Please refer to the Assistant for details.",
+    "0701_7000_0002_0003": "Failed to extrude the filament. Possible cause: extruder or nozzle clogged. Please refer to the Assistant for details.",
+    "0701_7000_0002_0004": "Failed to pull back the filament from the toolhead to AMS. Possible cause: filament or spool stuck. Please refer to the Assistant for details.",
+    "0701_7000_0002_0005": "Failed to feed the filament outside the AMS. Please clip the end of the filament flat and check to see if the spool is stuck. Please refer to the Assistant for details.",
+    "0701_7000_0002_0006": "Timeout purging old filament. Possible cause: filament stuck or extruder/nozzle clogged. Please refer to the Assistant for details.",
+    "0701_7000_0002_0007": "AMS filament ran out. Please put a new filament into AMS and click the 'Retry' button.",
+    "0701_7000_0002_0008": "Failed to get AMS mapping table; please click 'Resume' to retry",
+    "0701_7000_0002_0030": "",
+    "0701_7000_0002_0031": "",
+    "0701_7000_0002_0032": "",
+    "0701_7000_0002_0033": "",
+    "0701_7000_0002_0040": "",
+    "0701_7000_0002_0041": "",
+    "0701_7000_0002_0042": "",
+    "0701_7000_0002_0043": "",
+    "0701_7000_0002_0044": "",
+    "0701_7000_0002_0045": "",
+    "0701_7000_0002_0046": "",
+    "0701_7000_0002_0050": "",
+    "0701_7000_0002_0060": "",
+    "0701_7000_0002_0061": "",
+    "0701_8000_0001_0002": "AMS B The heater 1 is disconnected, which may due to poor connector contact.",
+    "0701_8100_0001_0002": "AMS B The heater 2 is disconnected, which may due to poor connector contact.",
+    "0701_9200_0001_0001": "AMS B The cooling fan of heater 1 is blocked, which may be due to the fan being stuck.",
+    "0701_9200_0002_0002": "AMS B The cooling fan speed of heater 1 is too low, which could be due to excessive fan resistance.",
+    "0701_9300_0001_0001": "AMS B The cooling fan of heater 2 is blocked, which may be due to the fan being stuck.",
+    "0701_9300_0002_0002": "AMS B The cooling fan speed of heater 2 is too low, which could be due to excessive fan resistance.",
+    "0701_9400_0001_0001": "AMS B The temperature sensor of heater 1 is malfunctioning, , which may due to poor connector contact.",
+    "0701_9500_0001_0001": "AMS B The temperature sensor of heater 2 is malfunctioning, , which may due to poor connector contact.",
+    "0702_0100_0001_0001": "The AMS C assist motor has slipped. The extrusion wheel may be worn down, or the filament may be too thin.",
+    "0702_0100_0001_0003": "The AMS C assist motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0702_0100_0001_0004": "The AMS C assist motor speed control is malfunctioning. The speed sensor may be faulty.",
+    "0702_0100_0001_0011": "AMS C The assist motor calibration parameter error. Please pull out the filament from the filament hub and then restart the AMS.",
+    "0702_0100_0002_0002": "The AMS C assist motor is overloaded. The filament may be tangled or stuck.",
+    "0702_0200_0001_0001": "AMS C Filament speed and length error: The filament odometry may be faulty.",
+    "0702_1000_0001_0001": "The AMS C slot1 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0702_1000_0001_0003": "The AMS C slot1 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0702_1000_0002_0002": "The AMS C slot1 motor is overloaded. The filament may be tangled or stuck.",
+    "0702_1100_0001_0001": "The AMS C slot2 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0702_1100_0001_0003": "The AMS C slot2 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0702_1100_0002_0002": "The AMS C slot2 motor is overloaded. The filament may be tangled or stuck.",
+    "0702_1200_0001_0001": "The AMS C slot3 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0702_1200_0001_0003": "The AMS C slot3 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0702_1200_0002_0002": "The AMS C slot3 motor is overloaded. The filament may be tangled or stuck.",
+    "0702_1300_0001_0001": "The AMS C slot4 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0702_1300_0001_0003": "The AMS C slot4 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0702_1300_0002_0002": "The AMS C slot4 motor is overloaded. The filament may be tangled or stuck.",
+    "0702_2000_0002_0001": "AMS C Slot1 filament has run out. Please insert a new filament.",
+    "0702_2000_0002_0002": "AMS C Slot1 is empty; please insert a new filament.",
+    "0702_2000_0002_0003": "AMS C Slot1's filament may be broken in AMS.",
+    "0702_2000_0002_0004": "AMS C Slot1 filament may be broken in the tool head.",
+    "0702_2000_0002_0005": "AMS C Slot1 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0702_2000_0002_0006": "PTFE tube detached during the feeding process. Please check if the PTFE tube is connected to the AMS and extruder.",
+    "0702_2000_0003_0001": "AMS C Slot1 filament has run out. Please wait while old filament is purged.",
+    "0702_2000_0003_0002": "AMS C Slot1 filament has run out and automatically switched to the slot with the same filament.",
+    "0702_2100_0002_0001": "AMS C Slot2 filament has run out. Please insert a new filament.",
+    "0702_2100_0002_0002": "AMS C Slot2 is empty; please insert a new filament.",
+    "0702_2100_0002_0003": "AMS C Slot2's filament may be broken in AMS.",
+    "0702_2100_0002_0004": "AMS C Slot2 filament may be broken in the tool head.",
+    "0702_2100_0002_0005": "AMS C Slot2 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0702_2100_0003_0001": "AMS C Slot2 filament has run out. Please wait while old filament is purged.",
+    "0702_2100_0003_0002": "AMS C Slot2 filament has run out and automatically switched to the slot with the same filament.",
+    "0702_2200_0002_0001": "AMS C Slot3 filament has run out. Please insert a new filament.",
+    "0702_2200_0002_0002": "AMS C Slot3 is empty; please insert a new filament.",
+    "0702_2200_0002_0003": "AMS C Slot3's filament may be broken in AMS.",
+    "0702_2200_0002_0004": "AMS C Slot3 filament may be broken in the tool head.",
+    "0702_2200_0002_0005": "AMS C Slot3 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0702_2200_0003_0001": "AMS C Slot3 filament has run out. Please wait while old filament is purged.",
+    "0702_2200_0003_0002": "AMS C Slot3 filament has run out and automatically switched to the slot with the same filament.",
+    "0702_2300_0002_0001": "AMS C Slot4 filament has run out. Please insert a new filament.",
+    "0702_2300_0002_0002": "AMS C Slot4 is empty; please insert a new filament.",
+    "0702_2300_0002_0003": "AMS C Slot4's filament may be broken in AMS.",
+    "0702_2300_0002_0004": "AMS C Slot4 filament may be broken in the tool head.",
+    "0702_2300_0002_0005": "AMS C Slot4 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0702_2300_0003_0001": "AMS C Slot4 filament has run out. Please wait while old filament is purged.",
+    "0702_2300_0003_0002": "AMS C Slot4 filament has run out and automatically switched to the slot with the same filament.",
+    "0702_3000_0001_0001": "The AMS C RFID 0 board has an error.",
+    "0702_3000_0001_0004": "Encryption chip failure.",
+    "0702_3000_0002_0002": "The RFID-tag on AMS C Slot1 is damaged or the it's content cannot be identified.",
+    "0702_3000_0003_0003": "RFID cannot be read because of a hardware or structural error.",
+    "0702_3100_0001_0001": "The AMS C RFID 1 board has an error.",
+    "0702_3100_0001_0004": "Encryption chip failure.",
+    "0702_3100_0002_0002": "The RFID-tag on AMS C Slot2 is damaged or the it's content cannot be identified.",
+    "0702_3100_0003_0003": "RFID cannot be read because of a hardware or structural error.",
+    "0702_3200_0002_0002": "The RFID-tag on AMS C Slot3 is damaged or the it's content cannot be identified.",
+    "0702_3300_0002_0002": "The RFID-tag on AMS C Slot4 is damaged or the it's content cannot be identified.",
+    "0702_3500_0001_0001": "The temperature and humidity sensor has an error. The chip may be faulty.",
+    "0702_3500_0001_0002": "AMS C The humidity sensor is disconnected, which may due to poor connector contact.",
+    "0702_5000_0002_0001": "AMS C communication is abnormal; please check the connection cable.",
+    "0702_6000_0002_0001": "The AMS C slot1 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0702_6100_0002_0001": "The AMS C slot2 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0702_6200_0002_0001": "The AMS C slot3 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0702_6300_0002_0001": "The AMS C slot4 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0702_7000_0002_0001": "Failed to pull out the filament from the extruder. Possible causes: clogged extruder or broken filament. Refer to the Assistant for details.",
+    "0702_7000_0002_0002": "Failed to feed the filament into the toolhead. Possible cause: filament or spool stuck. Please refer to the Assistant for details.",
+    "0702_7000_0002_0003": "Failed to extrude the filament. Possible cause: extruder or nozzle clogged. Please refer to the Assistant for details.",
+    "0702_7000_0002_0004": "Failed to pull back the filament from the toolhead to AMS. Possible cause: filament or spool stuck. Please refer to the Assistant for details.",
+    "0702_7000_0002_0005": "Failed to feed the filament outside the AMS. Please clip the end of the filament flat and check to see if the spool is stuck. Please refer to the Assistant for details.",
+    "0702_7000_0002_0006": "Timeout purging old filament. Possible cause: filament stuck or extruder/nozzle clogged. Please refer to the Assistant for details.",
+    "0702_7000_0002_0007": "AMS filament ran out. Please put a new filament into AMS and click the 'Retry' button.",
+    "0702_7000_0002_0008": "Failed to get AMS mapping table; please click 'Resume' to retry",
+    "0702_7000_0002_0030": "",
+    "0702_7000_0002_0031": "",
+    "0702_7000_0002_0032": "",
+    "0702_7000_0002_0033": "",
+    "0702_7000_0002_0040": "",
+    "0702_7000_0002_0041": "",
+    "0702_7000_0002_0042": "",
+    "0702_7000_0002_0043": "",
+    "0702_7000_0002_0044": "",
+    "0702_7000_0002_0045": "",
+    "0702_7000_0002_0046": "",
+    "0702_7000_0002_0050": "",
+    "0702_7000_0002_0060": "",
+    "0702_7000_0002_0061": "",
+    "0702_8000_0001_0002": "AMS C The heater 1 is disconnected, which may due to poor connector contact.",
+    "0702_8100_0001_0002": "AMS C The heater 2 is disconnected, which may due to poor connector contact.",
+    "0702_9200_0001_0001": "AMS C The cooling fan of heater 1 is blocked, which may be due to the fan being stuck.",
+    "0702_9200_0002_0002": "AMS C The cooling fan speed of heater 1 is too low, which could be due to excessive fan resistance.",
+    "0702_9300_0001_0001": "AMS C The cooling fan of heater 2 is blocked, which may be due to the fan being stuck.",
+    "0702_9300_0002_0002": "AMS C The cooling fan speed of heater 2 is too low, which could be due to excessive fan resistance.",
+    "0702_9400_0001_0001": "AMS C The temperature sensor of heater 1 is malfunctioning, , which may due to poor connector contact.",
+    "0702_9500_0001_0001": "AMS C The temperature sensor of heater 2 is malfunctioning, , which may due to poor connector contact.",
+    "0703_0100_0001_0001": "The AMS D assist motor has slipped. The extrusion wheel may be worn down, or the filament may be too thin.",
+    "0703_0100_0001_0003": "The AMS D assist motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0703_0100_0001_0004": "The AMS D assist motor speed control is malfunctioning. The speed sensor may be faulty.",
+    "0703_0100_0001_0011": "AMS D The assist motor calibration parameter error. Please pull out the filament from the filament hub and then restart the AMS.",
+    "0703_0100_0002_0002": "The AMS D assist motor is overloaded. The filament may be tangled or stuck.",
+    "0703_0200_0001_0001": "AMS D Filament speed and length error: The filament odometry may be faulty.",
+    "0703_1000_0001_0001": "The AMS D slot1 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0703_1000_0001_0003": "The AMS D slot1 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0703_1000_0002_0002": "The AMS D slot1 motor is overloaded. The filament may be tangled or stuck.",
+    "0703_1100_0001_0001": "The AMS D slot2 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0703_1100_0001_0003": "The AMS D slot2 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0703_1100_0002_0002": "The AMS D slot2 motor is overloaded. The filament may be tangled or stuck.",
+    "0703_1200_0001_0001": "The AMS D slot3 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0703_1200_0001_0003": "The AMS D slot3 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0703_1200_0002_0002": "The AMS D slot3 motor is overloaded. The filament may be tangled or stuck.",
+    "0703_1300_0001_0001": "The AMS D slot4 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "0703_1300_0001_0003": "The AMS D slot4 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "0703_1300_0002_0002": "The AMS D slot4 motor is overloaded. The filament may be tangled or stuck.",
+    "0703_2000_0002_0001": "AMS D Slot1 filament has run out. Please insert a new filament.",
+    "0703_2000_0002_0002": "AMS D Slot1 is empty; please insert a new filament.",
+    "0703_2000_0002_0003": "AMS D Slot1's filament may be broken in AMS.",
+    "0703_2000_0002_0004": "AMS D Slot1 filament may be broken in the tool head.",
+    "0703_2000_0002_0005": "AMS D Slot1 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0703_2000_0002_0006": "PTFE tube detached during the feeding process. Please check if the PTFE tube is connected to the AMS and extruder.",
+    "0703_2000_0003_0001": "AMS D Slot1 filament has run out. Please wait while old filament is purged.",
+    "0703_2000_0003_0002": "AMS D Slot1 filament has run out and automatically switched to the slot with the same filament.",
+    "0703_2100_0002_0001": "AMS D Slot2 filament has run out. Please insert a new filament.",
+    "0703_2100_0002_0002": "AMS D Slot2 is empty; please insert a new filament.",
+    "0703_2100_0002_0003": "AMS D Slot2's filament may be broken in AMS.",
+    "0703_2100_0002_0004": "AMS D Slot2 filament may be broken in the tool head.",
+    "0703_2100_0002_0005": "AMS D Slot2 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0703_2100_0003_0001": "AMS D Slot2 filament has run out. Please wait while old filament is purged.",
+    "0703_2100_0003_0002": "AMS D Slot2 filament has run out and automatically switched to the slot with the same filament.",
+    "0703_2200_0002_0001": "AMS D Slot3 filament has run out. Please insert a new filament.",
+    "0703_2200_0002_0002": "AMS D Slot3 is empty; please insert a new filament.",
+    "0703_2200_0002_0003": "AMS D Slot3's filament may be broken in AMS.",
+    "0703_2200_0002_0004": "AMS D Slot3 filament may be broken in the tool head.",
+    "0703_2200_0002_0005": "AMS D Slot3 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0703_2200_0003_0001": "AMS D Slot3 filament has run out. Please wait while old filament is purged.",
+    "0703_2200_0003_0002": "AMS D Slot3 filament has run out and automatically switched to the slot with the same filament.",
+    "0703_2300_0002_0001": "AMS D Slot4 filament has run out. Please insert a new filament.",
+    "0703_2300_0002_0002": "AMS D Slot4 is empty; please insert a new filament.",
+    "0703_2300_0002_0003": "AMS D Slot4's filament may be broken in AMS.",
+    "0703_2300_0002_0004": "AMS D Slot4 filament may be broken in the tool head.",
+    "0703_2300_0002_0005": "AMS D Slot4 filament has run out, and purging the old filament went abnormally; please check whether the filament is stuck in the tool head.",
+    "0703_2300_0003_0001": "AMS D Slot4 filament has run out. Please wait while old filament is purged.",
+    "0703_2300_0003_0002": "AMS D Slot4 filament has run out and automatically switched to the slot with the same filament.",
+    "0703_3000_0001_0001": "The AMS D RFID 0 board has an error.",
+    "0703_3000_0001_0004": "Encryption chip failure.",
+    "0703_3000_0002_0002": "The RFID-tag on AMS D Slot1 is damaged or the it's content cannot be identified.",
+    "0703_3000_0003_0003": "RFID cannot be read because of a hardware or structural error.",
+    "0703_3100_0001_0001": "The AMS D RFID 1 board has an error.",
+    "0703_3100_0001_0004": "Encryption chip failure.",
+    "0703_3100_0002_0002": "The RFID-tag on AMS D Slot2 is damaged or the it's content cannot be identified.",
+    "0703_3100_0003_0003": "RFID cannot be read because of a hardware or structural error.",
+    "0703_3200_0002_0002": "The RFID-tag on AMS D Slot3 is damaged or the it's content cannot be identified.",
+    "0703_3300_0002_0002": "The RFID-tag on AMS D Slot4 is damaged or the it's content cannot be identified.",
+    "0703_3500_0001_0001": "The temperature and humidity sensor has an error. The chip may be faulty.",
+    "0703_3500_0001_0002": "AMS D The humidity sensor is disconnected, which may due to poor connector contact.",
+    "0703_5000_0002_0001": "AMS D communication is abnormal; please check the connection cable.",
+    "0703_6000_0002_0001": "The AMS D slot1 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0703_6100_0002_0001": "The AMS D slot2 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0703_6200_0002_0001": "The AMS D slot3 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0703_6300_0002_0001": "The AMS D slot4 is overloaded. The filament may be tangled or the spool may be stuck.",
+    "0703_7000_0002_0001": "Failed to pull out the filament from the extruder. Possible causes: clogged extruder or broken filament. Refer to the Assistant for details.",
+    "0703_7000_0002_0002": "Failed to feed the filament into the toolhead. Possible cause: filament or spool stuck. Please refer to the Assistant for details.",
+    "0703_7000_0002_0003": "Failed to extrude the filament. Possible cause: extruder or nozzle clogged. Please refer to the Assistant for details.",
+    "0703_7000_0002_0004": "Failed to pull back the filament from the toolhead to AMS. Possible cause: filament or spool stuck. Please refer to the Assistant for details.",
+    "0703_7000_0002_0005": "Failed to feed the filament outside the AMS. Please clip the end of the filament flat and check to see if the spool is stuck. Please refer to the Assistant for details.",
+    "0703_7000_0002_0006": "Timeout purging old filament. Possible cause: filament stuck or extruder/nozzle clogged. Please refer to the Assistant for details.",
+    "0703_7000_0002_0007": "AMS filament ran out. Please put a new filament into AMS and click the 'Retry' button.",
+    "0703_7000_0002_0008": "Failed to get AMS mapping table; please click 'Resume' to retry",
+    "0703_7000_0002_0030": "",
+    "0703_7000_0002_0031": "",
+    "0703_7000_0002_0032": "",
+    "0703_7000_0002_0033": "",
+    "0703_7000_0002_0040": "",
+    "0703_7000_0002_0041": "",
+    "0703_7000_0002_0042": "",
+    "0703_7000_0002_0043": "",
+    "0703_7000_0002_0044": "",
+    "0703_7000_0002_0045": "",
+    "0703_7000_0002_0046": "",
+    "0703_7000_0002_0050": "",
+    "0703_7000_0002_0060": "",
+    "0703_7000_0002_0061": "",
+    "0703_8000_0001_0002": "AMS D The heater 1 is disconnected, which may due to poor connector contact.",
+    "0703_8100_0001_0002": "AMS D The heater 2 is disconnected, which may due to poor connector contact.",
+    "0703_9200_0001_0001": "AMS D The cooling fan of heater 1 is blocked, which may be due to the fan being stuck.",
+    "0703_9200_0002_0002": "AMS D The cooling fan speed of heater 1 is too low, which could be due to excessive fan resistance.",
+    "0703_9300_0001_0001": "AMS D The cooling fan of heater 2 is blocked, which may be due to the fan being stuck.",
+    "0703_9300_0002_0002": "AMS D The cooling fan speed of heater 2 is too low, which could be due to excessive fan resistance.",
+    "0703_9400_0001_0001": "AMS D The temperature sensor of heater 1 is malfunctioning, , which may due to poor connector contact.",
+    "0703_9500_0001_0001": "AMS D The temperature sensor of heater 2 is malfunctioning, , which may due to poor connector contact.",
+}

octoprint_bambu_printer/printer/pybambu/const_hms_errors.py

@@ -0,0 +1,528 @@
+HMS_ERRORS = {
+    "0300_0100_0001_0001": "The heatbed temperature is abnormal; the heater may have a short circuit.",
+    "0300_0100_0001_0002": "The heatbed temperature is abnormal; the heater may have an open circuit, or the thermal switch may be open.",
+    "0300_0100_0001_0003": "The heatbed temperature is abnormal; the heater is over temperature.",
+    "0300_0100_0001_0006": "The heatbed temperature is abnormal; the sensor may have a short circuit.",
+    "0300_0100_0001_0007": "The heatbed temperature is abnormal; the sensor may have an open circuit.",
+    "0300_0100_0001_0008": "An abnormality occurs during the heating process of the heatbed, the heating modules may be broken.",
+    "0300_0100_0001_000A": "The heatbed temperature control is abnormal, the AC board may be broken.",
+    "0300_0100_0001_000C": "The heatbed has worked at full load for a long time. The temperature control system may be abnormal.",
+    "0300_0100_0001_000D": "An issue occurred when heating the heatbed previously. To continue using your printer, please refer to the wiki to troubleshoot.",
+    "0300_0100_0003_0008": "The temperature of the heated bed exceeds the limit and automatically adjusts to the limit temperature.",
+    "0300_0200_0001_0001": "The nozzle temperature is abnormal; the heater may have a short circuit.",
+    "0300_0200_0001_0002": "The nozzle temperature is abnormal; the heater may have an open circuit.",
+    "0300_0200_0001_0003": "The nozzle temperature is abnormal; the heater is over temperature.",
+    "0300_0200_0001_0006": "The nozzle temperature is abnormal; the sensor may have a short circuit. Please check whether the connector is properly plugged in.",
+    "0300_0200_0001_0007": "The nozzle temperature is abnormal; the sensor may have an open circuit.",
+    "0300_0200_0001_0009": "The nozzle temperature control is abnormal; the hot end may not be installed. If you want to heat the hot end without it being installed, please turn on maintenance mode on the settings page.",
+    "0300_0200_0001_000B": "The nozzle temperature is abnormal. Temperature control system may have an issue.",
+    "0300_0300_0001_0001": "The hotend cooling fan speed is too slow or stopped. It may be stuck or the connector is not plugged in properly.",
+    "0300_0300_0002_0002": "",
+    "0300_0400_0002_0001": "The speed of the part cooling fan is too slow or stopped. It may be stuck or the connector is not plugged in properly.",
+    "0300_0500_0001_0001": "The motor driver is overheating. Its radiator may be loose, or its cooling fan may be damaged.",
+    "0300_0600_0001_0001": "Motor-A has an open-circuit. There may be a loose connection, or the motor may have failed.",
+    "0300_0600_0001_0002": "Motor-A has a short-circuit. It may have failed.",
+    "0300_0600_0001_0003": "The resistance of Motor-A is abnormal, the motor may have failed.",
+    "0300_0700_0001_0001": "Motor-B has an open-circuit. The connection may be loose, or the motor may have failed.",
+    "0300_0700_0001_0002": "Motor-B has a short-circuit. It may have failed.",
+    "0300_0700_0001_0003": "The resistance of Motor-B is abnormal, the motor may have failed.",
+    "0300_0800_0001_0001": "Motor-Z has an open-circuit. The connection may be loose, or the motor may have failed.",
+    "0300_0800_0001_0002": "Motor-Z has a short-circuit. It may have failed.",
+    "0300_0800_0001_0003": "The resistance of Motor-Z is abnormal, the motor may have failed.",
+    "0300_0900_0001_0001": "Motor-E has an open-circuit. The connection may be loose, or the motor may have failed.",
+    "0300_0900_0001_0002": "Motor-E has a short-circuit. It may have failed.",
+    "0300_0900_0001_0003": "The resistance of Motor-E is abnormal, the motor may have failed.",
+    "0300_0A00_0001_0001": "Heatbed force sensor 1 is too sensitive. It may be stuck between the strain arm and heatbed support, or the adjusting screw may be too tight.",
+    "0300_0A00_0001_0002": "The signal of heatbed force sensor 1 is weak. The force sensor may be broken or have poor electric connection.",
+    "0300_0A00_0001_0003": "The signal of heatbed force sensor 1 is too weak. The electronic connection to the sensor may be broken.",
+    "0300_0A00_0001_0004": "An external disturbance was detected on force sensor 1. The heatbed plate may have touched something outside the heatbed.",
+    "0300_0A00_0001_0005": "Force sensor 1 detected unexpected continuous force. The heatbed may be stuck, or the analog front end may be broken.",
+    "0300_0B00_0001_0001": "Heatbed force sensor 2 is too sensitive. It may be stuck between the strain arm and heatbed support, or the adjusting screw may be too tight.",
+    "0300_0B00_0001_0002": "The signal of heatbed force sensor 2 is weak. The force sensor may be broken or have poor electric connection.",
+    "0300_0B00_0001_0003": "The signal of heatbed force sensor 2 is too weak. The electronic connection to the sensor may be broken.",
+    "0300_0B00_0001_0004": "An external disturbance was detected on force sensor 2. The heatbed plate may have touched something outside the heatbed.",
+    "0300_0B00_0001_0005": "Force sensor 2 detected unexpected continuous force. The heatbed may be stuck, or the analog front end may be broken.",
+    "0300_0C00_0001_0001": "Heatbed force sensor 3 is too sensitive. It may be stuck between the strain arm and heatbed support, or the adjusting screw may be too tight.",
+    "0300_0C00_0001_0002": "The signal of heatbed force sensor 3 is weak. The force sensor may be broken or have poor electric connection.",
+    "0300_0C00_0001_0003": "The signal of heatbed force sensor 3 is too weak. The electronic connection to the sensor may be broken.",
+    "0300_0C00_0001_0004": "An external disturbance was detected on force sensor 3. The heatbed plate may have touched something outside the heatbed.",
+    "0300_0C00_0001_0005": "Force sensor 3 detected unexpected continuous force. The heatbed may be stuck, or the analog front end may be broken.",
+    "0300_0D00_0001_0002": "Heatbed homing failed. The environmental vibration is too great.",
+    "0300_0D00_0001_0003": "The build plate is not placed properly. Please adjust it.",
+    "0300_0D00_0001_0004": "The build plate is not placed properly. Please adjust it.",
+    "0300_0D00_0001_0005": "The build plate is not placed properly. Please adjust it.",
+    "0300_0D00_0001_0006": "The build plate is not placed properly. Please adjust it.",
+    "0300_0D00_0001_0007": "The build plate is not placed properly. Please adjust it.",
+    "0300_0D00_0001_0008": "The build plate is not placed properly. Please adjust it.",
+    "0300_0D00_0001_0009": "The build plate is not placed properly. Please adjust it.",
+    "0300_0D00_0001_000A": "The build plate is not placed properly. Please adjust it.",
+    "0300_0D00_0001_000B": "The Z axis motor seems to be stuck when moving. Please check if there is any foreign matter on the Z sliders or Z timing belt wheels .",
+    "0300_0D00_0002_0001": "Heatbed homing abnormal: there may be a bulge on the heatbed or the nozzle tip may not be clean.",
+    "0300_0D00_0002_0003": "The build plate may not be properly placed. If this message appears repeatedly, please check the Wiki for more reasons.",
+    "0300_0D00_0002_0004": "The build plate may not be properly placed. If this message appears repeatedly, please check the Wiki for more reasons.",
+    "0300_0D00_0002_0005": "The build plate may not be properly placed. If this message appears repeatedly, please check the Wiki for more reasons.",
+    "0300_0D00_0002_0006": "The build plate may not be properly placed. If this message appears repeatedly, please check the Wiki for more reasons.",
+    "0300_0D00_0002_0007": "The build plate may not be properly placed. If this message appears repeatedly, please check the Wiki for more reasons.",
+    "0300_0D00_0002_0008": "The build plate may not be properly placed. If this message appears repeatedly, please check the Wiki for more reasons.",
+    "0300_0D00_0002_0009": "The build plate may not be properly placed. If this message appears repeatedly, please check the Wiki for more reasons.",
+    "0300_0D00_0002_000A": "The build plate may not be properly placed. If this message appears repeatedly, please check the Wiki for more reasons.",
+    "0300_0F00_0001_0001": "Abnormal accelerometer data detected. Please try to restart the printer.",
+    "0300_1000_0002_0001": "The resonance frequency of the X axis is low. The timing belt may be loose.",
+    "0300_1000_0002_0002": "The resonance frequency of the X axis differs greatly from last calibration. Please clean the carbon rod and rerun the machine calibration afterward.",
+    "0300_1100_0002_0001": "The resonance frequency of the Y axis is low. The timing belt may be loose.",
+    "0300_1100_0002_0002": "The resonance frequency of the Y axis differs greatly from the last calibration. Please clean the carbon rod and rerun the machine calibration afterward.",
+    "0300_1200_0002_0001": "The front cover of the toolhead fell off.",
+    "0300_1300_0001_0001": "The current sensor of Motor-A is abnormal. This may be caused by a failure of the hardware sampling circuit.",
+    "0300_1400_0001_0001": "The current sensor of Motor-B is abnormal. This may be caused by a failure of the hardware sampling circuit.",
+    "0300_1500_0001_0001": "The current sensor of Motor-Z is abnormal. This may be caused by a failure of the hardware sampling circuit.",
+    "0300_1600_0001_0001": "The current sensor of Motor-E is abnormal. This may be caused by a failure of the hardware sampling circuit.",
+    "0300_1700_0001_0001": "The hotend cooling fan speed is too slow or stopped. It may be stuck or the connector may not be plugged in properly.",
+    "0300_1700_0002_0002": "The hotend cooling fan speed is slow. It may be stuck and need cleaning.",
+    "0300_1800_0001_0001": "The value of extrusion force sensor is low, the nozzle seems to not be installed.",
+    "0300_1800_0001_0002": "The sensitivity of the extrusion force sensor is low, the nozzle may not installed correctly.",
+    "0300_1800_0001_0003": "The extrusion force sensor is not available, the link between the MC and TH may be broken or the sensor is broken.",
+    "0300_1800_0001_0004": "The data from extrusion force sensor is abnormal, the sensor should be broken.",
+    "0300_1800_0001_0005": "The Z axis motor got stuck while moving, or the extrusion force sensor may have an issue; please check if there is any foreign matter on the Z sliders or Z timing belt wheels.",
+    "0300_1900_0001_0001": "The eddy current sensor on Y-axis is not available, the wire should be broken.",
+    "0300_1900_0002_0002": "The sensitivity of Y-axis eddy current sensor is too low.",
+    "0300_1A00_0002_0001": "The nozzle is covered with filaments, or the build plate is put in crooked.",
+    "0300_1A00_0002_0002": "The nozzle is clogged with filament.",
+    "0300_1B00_0001_0001": "The signal of the heatbed acceleration sensor is weak. The sensor may have fallen off or been damaged.",
+    "0300_1B00_0001_0002": "External disturbance was detected on the heatbed acceleeration sensor. The sensor signal wire may not be fixed.",
+    "0300_1B00_0001_0003": "The heatbed acceleration sensor detected unexpected continuous force. The sensor may be stuck, or the analog front end may be broken.",
+    "0300_1C00_0001_0001": "The extrusion motor driver is abnormal. The MOSFET may have a short circuit.",
+    "0300_1D00_0001_0001": "The position sensor of extrusion motor is abnormal. The connection to sensor may be loose.",
+    "0300_2000_0001_0001": "X axis homing abnormal: please check if the tool head is stuck or the carbon rod has too much resistance.",
+    "0300_2000_0001_0002": "Y axis homing abnormal: please check if the tool head is stuck or the Y carriage has too much resistance.",
+    "0300_2000_0001_0003": "X axis homing abnormal: the timing belt may be loose.",
+    "0300_2000_0001_0004": "Y axis homing abnormal: the timing belt may be loose.",
+    "0300_4000_0002_0001": "Data transmission over the serial port is abnormal; the software system may be faulty.",
+    "0300_4100_0001_0001": "The system voltage is unstable; triggering the power failure protection function.",
+    "0300_9000_0001_0001": "Chamber heating failed. The chamber heater may be failing to blow hot air.",
+    "0300_9000_0001_0002": "Chamber heating failed. The chamber may not be enclosed, or the ambient temperature may be too low, or the heat dissipation vent of the power supply may be blocked.",
+    "0300_9000_0001_0003": "Chamber heating failed. The temperature of power supply may be too high.",
+    "0300_9000_0001_0004": "Chamber heating failed. The speed of the heating fan is too low.",
+    "0300_9000_0001_0005": "Chamber heating failed. The thermal resistance is too high.",
+    "0300_9000_0001_0010": "The communication of chamber temperature controller is abnormal.",
+    "0300_9100_0001_0001": "The temperature of chamber heater 1 is abnormal. The heater may have a short circuit.",
+    "0300_9100_0001_0002": "The temperature of chamber heater 1 is abnormal. The heater may have an open circuit or the thermal fuse may have taken effect.",
+    "0300_9100_0001_0003": "The temperature of chamber heater 1 is abnormal. The heater is over temperature.",
+    "0300_9100_0001_0006": "The temperature of chamber heater 1 is abnormal. The sensor may have a short circuit.",
+    "0300_9100_0001_0007": "The temperature of chamber heater 1 is abnormal. The sensor may have an open circuit.",
+    "0300_9100_0001_0008": "Chamber heater 1 failed to rise to target temperature.",
+    "0300_9100_0001_000A": "The temperature of chamber heater 1 is abnormal. The AC board may be broken.",
+    "0300_9100_0001_000C": "The chamber heater 1 has been working at full load for a long time. The temperature control system may have an issue.",
+    "0300_9200_0001_0001": "The temperature of chamber heater 2 is abnormal. The heater may have a short circuit.",
+    "0300_9200_0001_0002": "The temperature of chamber heater 2 is abnormal. The heater may have an open circuit or the thermal fuse may be in effect.",
+    "0300_9200_0001_0003": "The temperature of chamber heater 2 is abnormal. The heater is over temperature.",
+    "0300_9200_0001_0006": "The temperature of chamber heater 2 is abnormal. The sensor may have a short circuit.",
+    "0300_9200_0001_0007": "The temperature of chamber heater 2 is abnormal. The sensor may have an open circuit.",
+    "0300_9200_0001_0008": "Chamber heater 2 failed to rise to target temperature.",
+    "0300_9200_0001_000A": "The temperature of chamber heater 2 is abnormal. The AC board may be broken.",
+    "0300_9300_0001_0001": "Chamber temperature is abnormal. The chamber heater's temperature sensor may have a short circuit.",
+    "0300_9300_0001_0002": "Chamber temperature is abnormal. The chamber heater's temperature sensor may have an open circuit.",
+    "0300_9300_0001_0003": "Chamber temperature is abnormal. The chamber heater's temperature sensor at the air outlet may have a short circuit.",
+    "0300_9300_0001_0004": "Chamber temperature is abnormal. The chamber heater's temperature sensor at the air outlet may have an open circuit.",
+    "0300_9300_0001_0005": "Chamber temperature is abnormal. The chamber heater's temperature sensor at the air inlet may have a short circuit.",
+    "0300_9300_0001_0006": "Chamber temperature is abnormal. The chamber heater's temperature sensor at the air inlet may have an open circuit.",
+    "0300_9300_0001_0007": "Chamber temperature is abnormal. The temperature sensor at the power supply may have a short circuit.",
+    "0300_9300_0001_0008": "Chamber temperature is abnormal. The temperature sensor at power supply may have an open circuit.",
+    "0300_9400_0002_0003": "Chamber failed to reach the desired temperature. The machine will stop waiting for the chamber temperature.",
+    "0300_9400_0003_0001": "Chamber cooling may be too slow. You can open the front door or top cover to help cooling if the air in chamber is non-toxic.",
+    "0300_9400_0003_0002": "Chamber temperature setting value exceed the limit, the boundary value will be set.",
+    "0300_9500_0001_0007": "",
+    "0300_9900_0001_0001": "",
+    "0300_9900_0001_0002": "",
+    "0300_9900_0001_0003": "",
+    "0300_9900_0003_0001": "",
+    "0500_0100_0002_0001": "The media pipeline is malfunctioning.",
+    "0500_0100_0002_0002": "USB camera is not connected. Please check video camera cable connection.",
+    "0500_0100_0002_0003": "USB camera is malfunctioning.",
+    "0500_0100_0003_0004": "Not enough space in MicroSD Card; please clear some space.",
+    "0500_0100_0003_0005": "MicroSD Card error: please reinsert, format or replace it.",
+    "0500_0100_0003_0006": "Unformatted MicroSD Card: please format it.",
+    "0500_0100_0003_0007": "Unable to record time-lapse photography without MicroSD card inserted.",
+    "0500_0200_0002_0001": "Failed to connect internet. Please check the network connection.",
+    "0500_0200_0002_0002": "Device login failed; please check your account information.",
+    "0500_0200_0002_0003": "Failed to connect internet; please check the network connection.",
+    "0500_0200_0002_0004": "Unauthorized user: please check your account information.",
+    "0500_0200_0002_0005": "Failed to connect internet; please check the network connection.",
+    "0500_0200_0002_0006": "Streaming function error. Please check the network and try again. You can restart or update the printer if the issue persists.",
+    "0500_0200_0002_0007": "Liveview service login failed; please check your network connection.",
+    "0500_0200_0002_0008": "Time synchronization failed.",
+    "0500_0300_0001_0001": "The MC module is malfunctioning; please restart the device or check device cable connection.",
+    "0500_0300_0001_0002": "The toolhead is malfunctioning. Please restart the device.",
+    "0500_0300_0001_0003": "The AMS module is malfunctioning. Please restart the device.",
+    "0500_0300_0001_0004": "The AHB module is malfunctioning. Please restart the device.",
+    "0500_0300_0001_0005": "Internal service is malfunctioning. Please restart the device.",
+    "0500_0300_0001_0006": "A system panic occurred. Please restart the device.",
+    "0500_0300_0001_0008": "A system hang occurred. Please restart the device.",
+    "0500_0300_0001_0009": "A system hang occurred. It has been recovered by automatic restart.",
+    "0500_0300_0001_000A": "System state is abnormal; please restore factory settings.",
+    "0500_0300_0001_000B": "The screen is malfunctioning; please restart the device.",
+    "0500_0300_0001_0021": "Hardware incompatible: please check the laser.",
+    "0500_0300_0001_0023": "The Chamber Temperature Control module is malfunctioning. Please restart the device.",
+    "0500_0300_0001_0024": "The current temperature is too low. In order to protect you and your printer. Printing task, moving axis and other operations is disabled. Please move the printer to an environment above 10°C.",
+    "0500_0300_0001_0025": "The current firmware is abnormal. Please update again.",
+    "0500_0300_0002_000C": "Wireless hardware error: please turn off/on WiFi or restart the device.",
+    "0500_0300_0002_000D": "The SD Card controller is malfunctioning.",
+    "0500_0300_0002_0010": "forward coredump, it is recovering.",
+    "0500_0300_0002_0011": "upgrade coredump, it is recovering.",
+    "0500_0300_0002_0012": "ipcam coredump, it is recovering.",
+    "0500_0300_0002_0013": "xcam coredump, it is recovering.",
+    "0500_0300_0002_0014": "bbl_screen coredump, it is recovering.",
+    "0500_0300_0002_0015": "device_gate coredump, it is recovering.",
+    "0500_0300_0002_0016": "device_manager coredump, it is recovering.",
+    "0500_0300_0002_0017": "recorder coredump, it is recovering.",
+    "0500_0300_0002_0018": "security coredump, it is recovering.",
+    "0500_0300_0002_0020": "Micro SD Card capacity is insufficient to cache print files.",
+    "0500_0300_0003_0007": "A system panic occurred. It has been recovered by automatic restart.",
+    "0500_0300_0003_0022": "MicroSD Card performance degradation has been detected. It may affect print jobs, logs, and video records. Please try to format or change the MicroSD card.",
+    "0500_0400_0001_0001": "Failed to download print job. Please check your network connection.",
+    "0500_0400_0001_0002": "Failed to report print state. Please check your network connection.",
+    "0500_0400_0001_0003": "The content of print file is unreadable. Please resend the print job.",
+    "0500_0400_0001_0004": "The print file is unauthorized.",
+    "0500_0400_0001_0006": "Failed to resume previous print.",
+    "0500_0400_0002_0007": "The bed temperature exceeds the filament's vitrification temperature, which may cause a nozzle clog. Please keep the front door of the printer open or lower the bed temperature.",
+    "0500_0400_0002_0010": "The RFID-tag on AMS A Slot1 cannot be identified.",
+    "0500_0400_0002_0011": "The RFID-tag on AMS A Slot2 cannot be identified.",
+    "0500_0400_0002_0012": "The RFID-tag on AMS A Slot3 cannot be identified.",
+    "0500_0400_0002_0013": "The RFID-tag on AMS A Slot4 cannot be identified.",
+    "0500_0400_0002_0014": "The RFID-tag on AMS B Slot1 cannot be identified.",
+    "0500_0400_0002_0015": "The RFID-tag on AMS B Slot2 cannot be identified.",
+    "0500_0400_0002_0016": "The RFID-tag on AMS B Slot3 cannot be identified.",
+    "0500_0400_0002_0017": "The RFID-tag on AMS B Slot4 cannot be identified.",
+    "0500_0400_0002_0018": "The RFID-tag on AMS C Slot1 cannot be identified.",
+    "0500_0400_0002_0019": "The RFID-tag on AMS C Slot2 cannot be identified.",
+    "0500_0400_0002_001A": "The RFID-tag on AMS C Slot3 cannot be identified.",
+    "0500_0400_0002_001B": "The RFID-tag on AMS C Slot4 cannot be identified.",
+    "0500_0400_0002_001C": "The RFID-tag on AMS D Slot1 cannot be identified.",
+    "0500_0400_0002_001D": "The RFID-tag on AMS D Slot2 cannot be identified.",
+    "0500_0400_0002_001E": "The RFID-tag on AMS D Slot3 cannot be identified.",
+    "0500_0400_0002_001F": "The RFID-tag on AMS D Slot4 cannot be identified.",
+    "0500_0400_0002_0020": "",
+    "0500_0400_0003_0008": "The door is detected to be open.",
+    "0500_0400_0003_0009": "The bed temperature exceeds filament's vitrification temperature, which may cause nozzle clog. Please keep the front door of printer open. Already turning off the door opening detection temporarily.",
+    "0500_0500_0001_0001": "The factory data of AP board is abnormal; please replace the AP board with a new one.",
+    "0500_0500_0001_0006": "The factory data of AP board is abnormal, please replace the AP board with a new one.",
+    "0500_0500_0003_0002": "The device is in the engineering state; please pay attention to the information security related matters.",
+    "07FF_2000_0002_0001": "External filament has run out; please load a new filament.",
+    "07FF_2000_0002_0002": "External filament is missing; please load a new filament.",
+    "07FF_2000_0002_0004": "Please pull the external filament from the extruder.",
+    "0C00_0100_0001_0001": "The Micro Lidar camera is offline. Please check the hardware connection.",
+    "0C00_0100_0001_0003": "Synchronization between the Micro Lidar camera and MCU is abnormal. Please restart your printer.",
+    "0C00_0100_0001_0004": "The Micro Lidar camera lens seems to be dirty. Please clean the lens.",
+    "0C00_0100_0001_0005": "Micro Lidar camera OTP parameter is abnormal. Please contact after-sales.",
+    "0C00_0100_0001_0009": "The chamber camera lens seems to be dirty. Please clean the lens.",
+    "0C00_0100_0001_000A": "The Micro Lidar LED may be broken.",
+    "0C00_0100_0001_000B": "Failed to calibrate Micro Lidar. Please make sure the calibration chart is clean and not occluded, and run machine calibration again.",
+    "0C00_0100_0002_0002": "The Micro Lidar camera is malfunctioning and related functions may fail. Please contact after-sales if this message keeps appearing in multiple prints.",
+    "0C00_0100_0002_0006": "Micro Lidar camera extrinsic parameters are abnormal. Please enable flowrate calibration in your next print.",
+    "0C00_0100_0002_0007": "Micro Lidar laser parameters are drifted. Please re-calibrate your printer.",
+    "0C00_0100_0002_0008": "Failed to get image from chamber camera. Spaghetti and waste chute pileup detection is not available for now.",
+    "0C00_0200_0001_0001": "The horizontal laser is not lit. Please check if it's covered or hardware connection is normal.",
+    "0C00_0200_0001_0005": "A new Micro Lidar was detected. Please calibrate it on Calibration page before use.",
+    "0C00_0200_0002_0002": "The horizontal laser line is too wide. Please check if the heatbed is dirty.",
+    "0C00_0200_0002_0003": "The horizontal laser is not bright enough at homing position. Please clean or replace heatbed if this message appears repeatedly.",
+    "0C00_0200_0002_0004": "Nozzle height seems too low. Please check if the nozzle is worn or tilted. Re-calibrate Lidar if the nozzle has been replaced.",
+    "0C00_0200_0002_0006": "Nozzle height seems too high. Please check if there is filament residual attached to the nozzle.",
+    "0C00_0200_0002_0007": "The vertical laser is not lit. Please check if it's covered or hardware connection is normal.",
+    "0C00_0200_0002_0008": "The vertical laser line is too wide. Please check if the heatbed is dirty.",
+    "0C00_0200_0002_0009": "The vertical laser is not bright enough at homing position. Please clean or replace heatbed if this message appears repeatedly.",
+    "0C00_0300_0001_0009": "The first layer inspection module rebooted abnormally. The inspection result may be inaccurate.",
+    "0C00_0300_0001_000A": "Your printer is in factory mode. Please contact Technical Support.",
+    "0C00_0300_0002_0001": "Filament exposure metering failed because laser reflection is too weak on this material. First layer inspection may be inaccurate.",
+    "0C00_0300_0002_0002": "First layer inspection terminated due to abnormal Lidar data.",
+    "0C00_0300_0002_0004": "First layer inspection is not supported for the current print job.",
+    "0C00_0300_0002_0005": "First layer inspection timed out abnormally, and the current results may be inaccurate.",
+    "0C00_0300_0002_000C": "The build plate localization marker is not detected. Please check if the build plate is aligned correctly.",
+    "0C00_0300_0002_000F": "Parts skipped before first layer inspection; the inspection will not be supported for the current print.",
+    "0C00_0300_0002_0010": "Foreign objects detected on heatbed, Please check and clean the heatbed.",
+    "0C00_0300_0003_0006": "Purged filament may have piled up in the waste chute. Please check and clean the chute.",
+    "0C00_0300_0003_0007": "Possible first layer defects have been detected. Please check the first layer quality and decide if the job should be stopped.",
+    "0C00_0300_0003_0008": "Possible spaghetti defects were detected. Please check the print quality and decide if the job should be stopped.",
+    "0C00_0300_0003_000B": "Inspecting the first layer: please wait a moment.",
+    "0C00_0300_0003_000D": "Some objects may have fallen down, or the extruder is not extruding normally. Please check and decide if the printing should be stopped.",
+    "0C00_0300_0003_000E": "Your nozzle seems to be covered with jammed or clogged material.",
+    "0C00_0300_0003_000F": "Your nozzle seems to be covered with jammed or clogged material.",
+    "0C00_0300_0003_0010": "Your printer seems to be printing without extruding.",
+    "0C00_0400_0001_0017": "",
+    "1200_1000_0001_0001": "The AMS A Slot1 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1200_1000_0001_0003": "The AMS A Slot1 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1200_1000_0002_0002": "The AMS A Slot1 motor is overloaded. The filament may be tangled or stuck.",
+    "1200_1100_0001_0001": "The AMS A Slot2 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1200_1100_0001_0003": "The AMS A Slot2 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1200_1100_0002_0002": "The AMS A Slot2 motor is overloaded. The filament may be tangled or stuck.",
+    "1200_1200_0001_0001": "The AMS A Slot3 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1200_1200_0001_0003": "The AMS A Slot3 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1200_1200_0002_0002": "The AMS A Slot3 motor is overloaded. The filament may be tangled or stuck.",
+    "1200_1300_0001_0001": "The AMS A Slot4 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1200_1300_0001_0003": "The AMS A Slot4 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1200_1300_0002_0002": "The AMS A Slot4 motor is overloaded. The filament may be tangled or stuck.",
+    "1200_2000_0002_0001": "AMS A Slot1 filament has run out; please insert a new filament.",
+    "1200_2000_0002_0002": "AMS A Slot 1 is empty; please insert a new filament.",
+    "1200_2000_0002_0003": "AMS A Slot1 filament may be broken in the PTFE tube.",
+    "1200_2000_0002_0004": "AMS A Slot1 filament may be broken in the tool head.",
+    "1200_2000_0002_0005": "AMS A Slot1 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1200_2000_0002_0006": "Failed to extrude AMS A Slot1 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1200_2000_0003_0001": "AMS A Slot1 filament has run out. Purging the old filament; please wait.",
+    "1200_2000_0003_0002": "AMS A Slot1 filament has run out and automatically switched to the slot with the same filament.",
+    "1200_2100_0002_0001": "AMS A Slot2 filament has run out; please insert a new filament.",
+    "1200_2100_0002_0002": "AMS A Slot 2 is empty; please insert a new filament.",
+    "1200_2100_0002_0003": "AMS A Slot2 filament may be broken in the PTFE tube.",
+    "1200_2100_0002_0004": "AMS A Slot2 filament may be broken in the tool head.",
+    "1200_2100_0002_0005": "AMS A Slot2 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1200_2100_0002_0006": "Failed to extrude AMS A Slot2 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1200_2100_0003_0001": "AMS A Slot2 filament has run out. Purging the old filament; please wait.",
+    "1200_2100_0003_0002": "AMS A Slot2 filament has run out and automatically switched to the slot with the same filament.",
+    "1200_2200_0002_0001": "AMS A Slot3 filament has run out; please insert a new filament.",
+    "1200_2200_0002_0002": "AMS A Slot 3 is empty; please insert a new filament.",
+    "1200_2200_0002_0003": "AMS A Slot3 filament may be broken in the PTFE tube.",
+    "1200_2200_0002_0004": "AMS A Slot3 filament may be broken in the tool head.",
+    "1200_2200_0002_0005": "AMS A Slot3 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1200_2200_0002_0006": "Failed to extrude AMS A Slot3 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1200_2200_0003_0001": "AMS A Slot3 filament has run out. Purging the old filament; please wait.",
+    "1200_2200_0003_0002": "AMS A Slot3 filament has run out and automatically switched to the slot with the same filament.",
+    "1200_2300_0002_0001": "AMS A Slot4 filament has run out; please insert a new filament.",
+    "1200_2300_0002_0002": "AMS A Slot 4 is empty; please insert a new filament.",
+    "1200_2300_0002_0003": "AMS A Slot4 filament may be broken in the PTFE tube.",
+    "1200_2300_0002_0004": "AMS A Slot4 filament may be broken in the tool head.",
+    "1200_2300_0002_0005": "AMS A Slot4 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1200_2300_0002_0006": "Failed to extrude AMS A Slot4 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1200_2300_0003_0001": "AMS A Slot4 filament has run out. Purging the old filament; please wait.",
+    "1200_2300_0003_0002": "AMS A Slot4 filament has run out and automatically switched to the slot with the same filament.",
+    "1200_2400_0002_0001": "Filament may be broken in the tool head.",
+    "1200_2500_0002_0001": "Failed to extrude the filament and the extruder may be clogged.",
+    "1200_3000_0001_0001": "AMS A Slot 1 RFID coil is broken or the RF hardware circuit has an error.",
+    "1200_3000_0001_0004": "RFID cannot be read because of an encryption chip failure in AMSA.",
+    "1200_3000_0002_0002": "The RFID-tag on AMS A Slot 1 is damaged.",
+    "1200_3000_0003_0003": "AMS A Slot1 RFID cannot be read because of a structural error.",
+    "1200_3100_0001_0001": "AMS A Slot 2 RFID coil is broken or the RF hardware circuit has an error.",
+    "1200_3100_0002_0002": "The RFID-tag on AMS A Slot 2 is damaged.",
+    "1200_3100_0003_0003": "AMS A Slot2 RFID cannot be read because of a structural error.",
+    "1200_3200_0001_0001": "AMS A Slot 3 RFID coil is broken or the RF hardware circuit has an error.",
+    "1200_3200_0002_0002": "The RFID-tag on AMS A Slot 3 is damaged.",
+    "1200_3200_0003_0003": "AMS A Slot3 RFID cannot be read because of a structural error.",
+    "1200_3300_0001_0001": "AMS A Slot 4 RFID coil is broken or the RF hardware circuit has an error.",
+    "1200_3300_0002_0002": "The RFID-tag on AMS A Slot 4 is damaged.",
+    "1200_3300_0003_0003": "AMS A Slot4 RFID cannot be read because of a structural error.",
+    "1200_4500_0002_0001": "The filament cutter sensor is malfunctioning. Please check whether the connector is properly plugged in.",
+    "1200_4500_0002_0002": "The filament cutter's cutting distance is too large. The X motor may lose steps.",
+    "1200_4500_0002_0003": "The filament cutter handle has not been released. The handle or blade may be jammed, or there could be an issue with the filament sensor connection.",
+    "1200_5000_0002_0001": "AMS A communication is abnormal; please check the connection cable.",
+    "1200_5100_0003_0001": "AMS is disabled; please load filament from spool holder.",
+    "1200_7000_0001_0001": "AMS A Filament speed and length error: The slot 1 filament odometry may be faulty.",
+    "1200_7100_0001_0001": "AMS A Filament speed and length error: The slot 2 filament odometry may be faulty.",
+    "1200_7200_0001_0001": "AMS A Filament speed and length error: The slot 3 filament odometry may be faulty.",
+    "1200_7300_0001_0001": "AMS A Filament speed and length error: The slot 4 filament odometry may be faulty.",
+    "1200_8000_0002_0001": "AMS A Slot1 filament may be tangled or stuck.",
+    "1200_8100_0002_0001": "AMS A Slot2 filament may be tangled or stuck.",
+    "1200_8200_0002_0001": "AMS A Slot3 filament may be tangled or stuck.",
+    "1200_8300_0002_0001": "AMS A Slot4 filament may be tangled or stuck.",
+    "1201_1000_0001_0001": "The AMS B Slot1 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1201_1000_0001_0003": "The AMS B Slot1 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1201_1000_0002_0002": "The AMS B Slot1 motor is overloaded. The filament may be tangled or stuck.",
+    "1201_1100_0001_0001": "The AMS B Slot2 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1201_1100_0001_0003": "The AMS B Slot2 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1201_1100_0002_0002": "The AMS B Slot2 motor is overloaded. The filament may be tangled or stuck.",
+    "1201_1200_0001_0001": "The AMS B Slot3 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1201_1200_0001_0003": "The AMS B Slot3 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1201_1200_0002_0002": "The AMS B Slot3 motor is overloaded. The filament may be tangled or stuck.",
+    "1201_1300_0001_0001": "The AMS B Slot4 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1201_1300_0001_0003": "The AMS B Slot4 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1201_1300_0002_0002": "The AMS B Slot4 motor is overloaded. The filament may be tangled or stuck.",
+    "1201_2000_0002_0001": "AMS B Slot1 filament has run out; please insert a new filament.",
+    "1201_2000_0002_0002": "AMS B Slot 1 is empty; please insert a new filament.",
+    "1201_2000_0002_0003": "AMS B Slot1 filament may be broken in the PTFE tube.",
+    "1201_2000_0002_0004": "AMS B Slot1 filament may be broken in the tool head.",
+    "1201_2000_0002_0005": "AMS B Slot1 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1201_2000_0002_0006": "Failed to extrude AMS B Slot1 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1201_2000_0003_0001": "AMS B Slot1 filament has run out. Purging the old filament; please wait.",
+    "1201_2000_0003_0002": "AMS B Slot1 filament has run out and automatically switched to the slot with the same filament.",
+    "1201_2100_0002_0001": "AMS B Slot2 filament has run out; please insert a new filament.",
+    "1201_2100_0002_0002": "AMS B Slot 2 is empty; please insert a new filament.",
+    "1201_2100_0002_0003": "AMS B Slot2 filament may be broken in the PTFE tube.",
+    "1201_2100_0002_0004": "AMS B Slot2 filament may be broken in the tool head.",
+    "1201_2100_0002_0005": "AMS B Slot2 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1201_2100_0002_0006": "Failed to extrude AMS B Slot2 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1201_2100_0003_0001": "AMS B Slot2 filament has run out. Purging the old filament; please wait.",
+    "1201_2100_0003_0002": "AMS B Slot2 filament has run out and automatically switched to the slot with the same filament.",
+    "1201_2200_0002_0001": "AMS B Slot3 filament has run out; please insert a new filament.",
+    "1201_2200_0002_0002": "AMS B Slot 3 is empty; please insert a new filament.",
+    "1201_2200_0002_0003": "AMS B Slot3 filament may be broken in the PTFE tube.",
+    "1201_2200_0002_0004": "AMS B Slot3 filament may be broken in the tool head.",
+    "1201_2200_0002_0005": "AMS B Slot3 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1201_2200_0002_0006": "Failed to extrude AMS B Slot3 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1201_2200_0003_0001": "AMS B Slot3 filament has run out. Purging the old filament; please wait.",
+    "1201_2200_0003_0002": "AMS B Slot3 filament has run out and automatically switched to the slot with the same filament.",
+    "1201_2300_0002_0001": "AMS B Slot4 filament has run out; please insert a new filament.",
+    "1201_2300_0002_0002": "AMS B Slot 4 is empty; please insert a new filament.",
+    "1201_2300_0002_0003": "AMS B Slot4 filament may be broken in the PTFE tube.",
+    "1201_2300_0002_0004": "AMS B Slot4 filament may be broken in the tool head.",
+    "1201_2300_0002_0005": "AMS B Slot4 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1201_2300_0002_0006": "Failed to extrude AMS B Slot4 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1201_2300_0003_0001": "AMS B Slot4 filament has run out. Purging the old filament; please wait.",
+    "1201_2300_0003_0002": "AMS B Slot4 filament has run out and automatically switched to the slot with the same filament.",
+    "1201_3000_0001_0001": "AMS B Slot 1 RFID coil is broken or the RF hardware circuit has an error.",
+    "1201_3000_0001_0004": "RFID cannot be read because of an encryption chip failure in AMSB.",
+    "1201_3000_0002_0002": "The RFID-tag on AMS B Slot 1 is damaged.",
+    "1201_3000_0003_0003": "AMS B Slot1 RFID cannot be read because of a structural error.",
+    "1201_3100_0001_0001": "AMS B Slot 2 RFID coil is broken or the RF hardware circuit has an error.",
+    "1201_3100_0002_0002": "The RFID-tag on AMS B Slot 2 is damaged.",
+    "1201_3100_0003_0003": "AMS B Slot2 RFID cannot be read because of a structural error.",
+    "1201_3200_0001_0001": "AMS B Slot 3 RFID coil is broken or the RF hardware circuit has an error.",
+    "1201_3200_0002_0002": "The RFID-tag on AMS B Slot 3 is damaged.",
+    "1201_3200_0003_0003": "AMS B Slot3 RFID cannot be read because of a structural error.",
+    "1201_3300_0001_0001": "AMS B Slot 4 RFID coil is broken or the RF hardware circuit has an error.",
+    "1201_3300_0002_0002": "The RFID-tag on AMS B Slot 4 is damaged.",
+    "1201_3300_0003_0003": "AMS B Slot4 RFID cannot be read because of a structural error.",
+    "1201_5000_0002_0001": "AMS B communication is abnormal; please check the connection cable.",
+    "1201_7000_0001_0001": "AMS B Filament speed and length error: The slot 1 filament odometry may be faulty.",
+    "1201_7100_0001_0001": "AMS B Filament speed and length error: The slot 2 filament odometry may be faulty.",
+    "1201_7200_0001_0001": "AMS B Filament speed and length error: The slot 3 filament odometry may be faulty.",
+    "1201_7300_0001_0001": "AMS B Filament speed and length error: The slot 4 filament odometry may be faulty.",
+    "1201_8000_0002_0001": "AMS B Slot1 filament may be tangled or stuck.",
+    "1201_8100_0002_0001": "AMS B Slot2 filament may be tangled or stuck.",
+    "1201_8200_0002_0001": "AMS B Slot3 filament may be tangled or stuck.",
+    "1201_8300_0002_0001": "AMS B Slot4 filament may be tangled or stuck.",
+    "1202_1000_0001_0001": "The AMS C Slot1 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1202_1000_0001_0003": "The AMS C Slot1 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1202_1000_0002_0002": "The AMS C Slot1 motor is overloaded. The filament may be tangled or stuck.",
+    "1202_1100_0001_0001": "The AMS C Slot2 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1202_1100_0001_0003": "The AMS C Slot2 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1202_1100_0002_0002": "The AMS C Slot2 motor is overloaded. The filament may be tangled or stuck.",
+    "1202_1200_0001_0001": "The AMS C Slot3 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1202_1200_0001_0003": "The AMS C Slot3 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1202_1200_0002_0002": "The AMS C Slot3 motor is overloaded. The filament may be tangled or stuck.",
+    "1202_1300_0001_0001": "The AMS C Slot4 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1202_1300_0001_0003": "The AMS C Slot4 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1202_1300_0002_0002": "The AMS C Slot4 motor is overloaded. The filament may be tangled or stuck.",
+    "1202_2000_0002_0001": "AMS C Slot1 filament has run out; please insert a new filament.",
+    "1202_2000_0002_0002": "AMS C Slot 1 is empty; please insert a new filament.",
+    "1202_2000_0002_0003": "AMS C Slot1 filament may be broken in the PTFE tube.",
+    "1202_2000_0002_0004": "AMS C Slot1 filament may be broken in the tool head.",
+    "1202_2000_0002_0005": "AMS C Slot1 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1202_2000_0002_0006": "Failed to extrude AMS C Slot1 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1202_2000_0003_0001": "AMS C Slot1 filament has run out. Purging the old filament; please wait.",
+    "1202_2000_0003_0002": "AMS C Slot1 filament has run out and automatically switched to the slot with the same filament.",
+    "1202_2100_0002_0001": "AMS C Slot2 filament has run out; please insert a new filament.",
+    "1202_2100_0002_0002": "AMS C Slot 2 is empty; please insert a new filament.",
+    "1202_2100_0002_0003": "AMS C Slot2 filament may be broken in the PTFE tube.",
+    "1202_2100_0002_0004": "AMS C Slot2 filament may be broken in the tool head.",
+    "1202_2100_0002_0005": "AMS C Slot2 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1202_2100_0002_0006": "Failed to extrude AMS C Slot2 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1202_2100_0003_0001": "AMS C Slot2 filament has run out. Purging the old filament; please wait.",
+    "1202_2100_0003_0002": "AMS C Slot2 filament has run out and automatically switched to the slot with the same filament.",
+    "1202_2200_0002_0001": "AMS C Slot3 filament has run out; please insert a new filament.",
+    "1202_2200_0002_0002": "AMS C Slot 3 is empty; please insert a new filament.",
+    "1202_2200_0002_0003": "AMS C Slot3 filament may be broken in the PTFE tube.",
+    "1202_2200_0002_0004": "AMS C Slot3 filament may be broken in the tool head.",
+    "1202_2200_0002_0005": "AMS C Slot3 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1202_2200_0002_0006": "Failed to extrude AMS C Slot3 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1202_2200_0003_0001": "AMS C Slot3 filament has run out. Purging the old filament; please wait.",
+    "1202_2200_0003_0002": "AMS C Slot3 filament has run out and automatically switched to the slot with the same filament.",
+    "1202_2300_0002_0001": "AMS C Slot4 filament has run out; please insert a new filament.",
+    "1202_2300_0002_0002": "AMS C Slot 4 is empty; please insert a new filament.",
+    "1202_2300_0002_0003": "AMS C Slot4 filament may be broken in the PTFE tube.",
+    "1202_2300_0002_0004": "AMS C Slot4 filament may be broken in the tool head.",
+    "1202_2300_0002_0005": "AMS C Slot4 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1202_2300_0002_0006": "Failed to extrude AMS C Slot4 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1202_2300_0003_0001": "AMS C Slot4 filament has run out. Purging the old filament; please wait.",
+    "1202_2300_0003_0002": "AMS C Slot4 filament has run out and automatically switched to the slot with the same filament.",
+    "1202_3000_0001_0001": "AMS C Slot 1 RFID coil is broken or the RF hardware circuit has an error.",
+    "1202_3000_0001_0004": "RFID cannot be read because of an encryption chip failure in AMSC.",
+    "1202_3000_0002_0002": "The RFID-tag on AMS C Slot 1 is damaged.",
+    "1202_3000_0003_0003": "AMS C Slot1 RFID cannot be read because of a structural error.",
+    "1202_3100_0001_0001": "AMS C Slot 2 RFID coil is broken or the RF hardware circuit has an error.",
+    "1202_3100_0002_0002": "The RFID-tag on AMS C Slot 2 is damaged.",
+    "1202_3100_0003_0003": "AMS C Slot2 RFID cannot be read because of a structural error.",
+    "1202_3200_0001_0001": "AMS C Slot 3 RFID coil is broken or the RF hardware circuit has an error.",
+    "1202_3200_0002_0002": "The RFID-tag on AMS C Slot 3 is damaged.",
+    "1202_3200_0003_0003": "AMS C Slot3 RFID cannot be read because of a structural error.",
+    "1202_3300_0001_0001": "AMS C Slot 4 RFID coil is broken or the RF hardware circuit has an error.",
+    "1202_3300_0002_0002": "The RFID-tag on AMS C Slot 4 is damaged.",
+    "1202_3300_0003_0003": "AMS C Slot4 RFID cannot be read because of a structural error.",
+    "1202_5000_0002_0001": "AMS C communication is abnormal; please check the connection cable.",
+    "1202_7000_0001_0001": "AMS C Filament speed and length error: The slot 1 filament odometry may be faulty.",
+    "1202_7100_0001_0001": "AMS C Filament speed and length error: The slot 2 filament odometry may be faulty.",
+    "1202_7200_0001_0001": "AMS C Filament speed and length error: The slot 3 filament odometry may be faulty.",
+    "1202_7300_0001_0001": "AMS C Filament speed and length error: The slot 4 filament odometry may be faulty.",
+    "1202_8000_0002_0001": "AMS C Slot1 filament may be tangled or stuck.",
+    "1202_8100_0002_0001": "AMS C Slot2 filament may be tangled or stuck.",
+    "1202_8200_0002_0001": "AMS C Slot3 filament may be tangled or stuck.",
+    "1202_8300_0002_0001": "AMS C Slot4 filament may be tangled or stuck.",
+    "1203_1000_0001_0001": "The AMS D Slot1 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1203_1000_0001_0003": "The AMS D Slot1 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1203_1000_0002_0002": "The AMS D Slot1 motor is overloaded. The filament may be tangled or stuck.",
+    "1203_1100_0001_0001": "The AMS D Slot2 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1203_1100_0001_0003": "The AMS D Slot2 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1203_1100_0002_0002": "The AMS D Slot2 motor is overloaded. The filament may be tangled or stuck.",
+    "1203_1200_0001_0001": "The AMS D Slot3 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1203_1200_0001_0003": "The AMS D Slot3 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1203_1200_0002_0002": "The AMS D Slot3 motor is overloaded. The filament may be tangled or stuck.",
+    "1203_1300_0001_0001": "The AMS D Slot4 motor has slipped. The extrusion wheel may be malfunctioning, or the filament may be too thin.",
+    "1203_1300_0001_0003": "The AMS D Slot4 motor torque control is malfunctioning. The current sensor may be faulty.",
+    "1203_1300_0002_0002": "The AMS D Slot4 motor is overloaded. The filament may be tangled or stuck.",
+    "1203_2000_0002_0001": "AMS D Slot1 filament has run out; please insert a new filament.",
+    "1203_2000_0002_0002": "AMS D Slot 1 is empty; please insert a new filament.",
+    "1203_2000_0002_0003": "AMS D Slot1 filament may be broken in the PTFE tube.",
+    "1203_2000_0002_0004": "AMS D Slot1 filament may be broken in the tool head.",
+    "1203_2000_0002_0005": "AMS D Slot1 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1203_2000_0002_0006": "Failed to extrude AMS D Slot1 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1203_2000_0003_0001": "AMS D Slot1 filament has run out. Purging the old filament; please wait.",
+    "1203_2000_0003_0002": "AMS D Slot1 filament has run out and automatically switched to the slot with the same filament.",
+    "1203_2100_0002_0001": "AMS D Slot2 filament has run out; please insert a new filament.",
+    "1203_2100_0002_0002": "AMS D Slot 2 is empty; please insert a new filament.",
+    "1203_2100_0002_0003": "AMS D Slot2 filament may be broken in the PTFE tube.",
+    "1203_2100_0002_0004": "AMS D Slot2 filament may be broken in the tool head.",
+    "1203_2100_0002_0005": "AMS D Slot2 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1203_2100_0002_0006": "Failed to extrude AMS D Slot2 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1203_2100_0003_0001": "AMS D Slot2 filament has run out. Purging the old filament; please wait.",
+    "1203_2100_0003_0002": "AMS D Slot2 filament has run out and automatically switched to the slot with the same filament.",
+    "1203_2200_0002_0001": "AMS D Slot3 filament has run out; please insert a new filament.",
+    "1203_2200_0002_0002": "AMS D Slot 3 is empty; please insert a new filament.",
+    "1203_2200_0002_0003": "AMS D Slot3 filament may be broken in the PTFE tube.",
+    "1203_2200_0002_0004": "AMS D Slot3 filament may be broken in the tool head.",
+    "1203_2200_0002_0005": "AMS D Slot3 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1203_2200_0002_0006": "Failed to extrude AMS D Slot3 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1203_2200_0003_0001": "AMS D Slot3 filament has run out. Purging the old filament; please wait.",
+    "1203_2200_0003_0002": "AMS D Slot3 filament has run out and automatically switched to the slot with the same filament.",
+    "1203_2300_0002_0001": "AMS D Slot4 filament has run out; please insert a new filament.",
+    "1203_2300_0002_0002": "AMS D Slot 4 is empty; please insert a new filament.",
+    "1203_2300_0002_0003": "AMS D Slot4 filament may be broken in the PTFE tube.",
+    "1203_2300_0002_0004": "AMS D Slot4 filament may be broken in the tool head.",
+    "1203_2300_0002_0005": "AMS D Slot4 filament has run out, and purging the old filament went abnormally; please check to see if filament is stuck in the toolhead.",
+    "1203_2300_0002_0006": "Failed to extrude AMS D Slot4 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip.",
+    "1203_2300_0003_0001": "AMS D Slot4 filament has run out. Purging the old filament; please wait.",
+    "1203_2300_0003_0002": "AMS D Slot4 filament has run out and automatically switched to the slot with the same filament.",
+    "1203_3000_0001_0001": "AMS D Slot 1 RFID coil is broken or the RF hardware circuit has an error.",
+    "1203_3000_0001_0004": "RFID cannot be read because of an encryption chip failure in AMSD.",
+    "1203_3000_0002_0002": "The RFID-tag on AMS D Slot 1 is damaged.",
+    "1203_3000_0003_0003": "AMS D Slot1 RFID cannot be read because of a structural error.",
+    "1203_3100_0001_0001": "AMS D Slot 2 RFID coil is broken or the RF hardware circuit has an error.",
+    "1203_3100_0002_0002": "The RFID-tag on AMS D Slot 2 is damaged.",
+    "1203_3100_0003_0003": "AMS D Slot2 RFID cannot be read because of a structural error.",
+    "1203_3200_0001_0001": "AMS D Slot 3 RFID coil is broken or the RF hardware circuit has an error.",
+    "1203_3200_0002_0002": "The RFID-tag on AMS D Slot 3 is damaged.",
+    "1203_3200_0003_0003": "AMS D Slot3 RFID cannot be read because of a structural error.",
+    "1203_3300_0001_0001": "AMS D Slot 4 RFID coil is broken or the RF hardware circuit has an error.",
+    "1203_3300_0002_0002": "The RFID-tag on AMS D Slot 4 is damaged.",
+    "1203_3300_0003_0003": "AMS D Slot4 RFID cannot be read because of a structural error.",
+    "1203_5000_0002_0001": "AMS D communication is abnormal; please check the connection cable.",
+    "1203_7000_0001_0001": "AMS D Filament speed and length error: The slot 1 filament odometry may be faulty.",
+    "1203_7100_0001_0001": "AMS D Filament speed and length error: The slot 2 filament odometry may be faulty.",
+    "1203_7200_0001_0001": "AMS D Filament speed and length error: The slot 3 filament odometry may be faulty.",
+    "1203_7300_0001_0001": "AMS D Filament speed and length error: The slot 4 filament odometry may be faulty.",
+    "1203_8000_0002_0001": "AMS D Slot1 filament may be tangled or stuck.",
+    "1203_8100_0002_0001": "AMS D Slot2 filament may be tangled or stuck.",
+    "1203_8200_0002_0001": "AMS D Slot3 filament may be tangled or stuck.",
+    "1203_8300_0002_0001": "AMS D Slot4 filament may be tangled or stuck.",
+    "12FF_2000_0002_0001": "Filament at the spool holder has run out; please insert a new filament.",
+    "12FF_2000_0002_0002": "Filament on the spool holder is empty; please insert a new filament.",
+    "12FF_2000_0002_0004": "Please pull out the filament on the spool holder from the extruder.",
+    "12FF_2000_0002_0005": "Filament may be broken in the tool head.",
+    "12FF_2000_0002_0006": "Failed to extrude the filament and the extruder may be clogged.",
+    "12FF_2000_0002_0007": "Failed to check the filament location in the tool head; please click for more help.",
+    "12FF_2000_0003_0007": "Checking the filament location of all AMS slots, please wait.",
+    "12FF_8000_0002_0001": "The filament on the spool holder may be tangled or stuck.",
+}

octoprint_bambu_printer/printer/pybambu/const_print_errors.py

@@ -0,0 +1,276 @@
+PRINT_ERROR_ERRORS = {
+    "0300_4000": "Printing stopped because homing Z axis failed.",
+    "0300_4001": "The printer timed out waiting for the nozzle to cool down before homing.",
+    "0300_4002": "Printing Stopped because Auto Bed Leveling failed.",
+    "0300_4003": "Nozzle temperature malfunction.",
+    "0300_4004": "Heatbed temperature malfunction.",
+    "0300_4005": "The hotend cooling fan speed is abnormal.",
+    "0300_4006": "The nozzle is clogged.",
+    "0300_4008": "The AMS failed to change filament.",
+    "0300_4009": "Homing XY axis failed.",
+    "0300_400A": "Mechanical resonance frequency identification failed.",
+    "0300_400B": "Internal communication exception.",
+    "0300_400C": "Printing was cancelled.",
+    "0300_400D": "Resume failed after power loss.",
+    "0300_400E": "The motor self-check failed.",
+    "0300_400F": "No build plate is placed.",
+    "0300_8000": "Printing was paused for unknown reason. You can tap 'Resume' to resume the print job.",
+    "0300_8001": "Printing paused. It was due to the pause command added in the printing file.",
+    "0300_8002": "First layer defects were detected by the Micro Lidar. Please check the quality of the printed model before continuing your print.",
+    "0300_8003": "Spaghetti defects were detected by the AI Print Monitoring. Please check the quality of the printed model before continuing your print.",
+    "0300_8004": "Filament ran out. Please load new filament.",
+    "0300_8005": "Toolhead front cover fell off. Please remount the front cover and check to make sure your print is going okay.",
+    "0300_8006": "The build plate marker was not detected. Please confirm the build plate is correctly positioned on the heatbed with all four corners aligned, and the maker is clear.",
+    "0300_8007": "There was an unfinished print job when the printer lost power. If the model is still adhered to the build plate, you can try resuming the print job.",
+    "0300_8008": "Printing Stopped because nozzle temperature problem.",
+    "0300_8009": "Heatbed temperature malfunction.",
+    "0300_800A": "A Filament pile-up was detected by the AI Print Monitoring. Please clean the filament from the waste chute.",
+    "0300_800B": "The cutter is stuck. Please make sure the cutter handle is out, and check the filament sensor cable connection.",
+    "0300_800C": "Skipping step detected, auto-recover complete; please resume print and check if there are any layer shift problems.",
+    "0300_800D": "Some objects have fallen down, or the extruder is not extruding normally. If the defects are acceptable, click 'Resume' button to resume the print job.",
+    "0300_800E": "The print file is not available. Please check to see if the storage media has been removed.",
+    "0300_800F": "The door seems to be open, so printing was paused.",
+    "0300_8010": "The hotend cooling fan speed is abnormal.",
+    "0300_8011": "Detected build plate is not the same as the Gcode file. Please adjust slicer settings or use the correct plate.",
+    "0300_8012": "",
+    "0300_8013": "Printing was paused by the user. You can select 'Resume' to continue printing.",
+    "0300_8014": "The nozzle is covered with filaments, or the build plate is installed incorrectly. Please cancel this printing and clean the nozzle or adjust the build plate according to the actual status, or tap 'Resume' button to resume the print job.",
+    "0300_8015": "The filament on external spool has run out, please load new filament. If the filament is loaded, please select 'Resume'.",
+    "0300_8016": "The nozzle is clogged up with filaments. Please cancel this printing and clean the nozzle according to the actual status, or tap 'Resume' button to resume the print job.",
+    "0300_8017": "Foreign objects detected on heatbed, Please check and clean the heatbed, Then tap 'Resume' button to resume the print job.",
+    "0300_8018": "Chamber temperature malfunction.",
+    "0300_8019": "No build plate is placed.",
+    "0300_801B": "Nozzle temperature problem detected. Refer to the Assistant to re-connect the hotend connector. POWER OFF the printer before this operation to avoid a short circuit.",
+    "0500_4001": "Failed to connect to Bambu Cloud. Please check your network connection.",
+    "0500_4002": "Unsupported print file path or name. Please resend the printing job.",
+    "0500_4003": "Printing stopped because the printer was unable to parse the file. Please resend your print job.",
+    "0500_4004": "The printer can't receive new print jobs while printing. Resend after the current print finishes.",
+    "0500_4005": "Print jobs are not allowed to be sent while updating firmware.",
+    "0500_4006": "There is not enough free storage space for the print job. Restoring to factory settings can release available space.",
+    "0500_4007": "Print jobs are not allowed to be sent while force updating or when repair updating is required.",
+    "0500_4008": "Starting printing failed. please power cycle the printer and resend the print job.",
+    "0500_4009": "Print jobs are not allowed to be sent while updating logs.",
+    "0500_400A": "The file name is not supported. Please rename and restart the printing job.",
+    "0500_400B": "There was a problem downloading a file. Please check you network connection and resend the printing job.",
+    "0500_400C": "Please insert a MicroSD card and restart the printing job.",
+    "0500_400D": "Please run a self-test and restart the printing job.",
+    "0500_400E": "Printing was cancelled.",
+    "0500_4012": "The door seems to be open, so printing was paused.",
+    "0500_4014": "Slicing for the print job failed. Please check your settings and restart the print job.",
+    "0500_4015": "There is not enough free storage space for the print job. Please format or clean MicroSD card to release available space.",
+    "0500_4016": "The MicroSD Card is write-protected. Please replace the MicroSD Card.",
+    "0500_4017": "Binding failed. Please retry or restart the printer and retry.",
+    "0500_4018": "Binding configuration information parsing failed,  please try again.",
+    "0500_4019": "The printer has already been bound. Please unbind it and try again.",
+    "0500_401A": "Cloud access failed. Possible reasons include network instability caused by interference, inability to access the internet, or router firewall configuration restrictions. You can try moving the printer closer to the router or checking the router configuration and then try again.",
+    "0500_401B": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_401C": "Cloud access is rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_401D": "Cloud access failed, which may be caused by network instability due to interference. You can try moving the printer closer to the router before you try again.",
+    "0500_401E": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_401F": "Authorization timed out. Please make sure that your phone or PC has access to the internet, and ensure that the Bambu Studio/Bambu Handy APP is running in the foreground during the binding operation.",
+    "0500_4020": "Cloud access rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_4021": "Cloud access failed, which may be caused by network instability due to interference. You can try moving the printer closer to the router before you try again.",
+    "0500_4022": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_4023": "Cloud access rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_4024": "Cloud access failed. Possible reasons include network instability caused by interference, inability to access the internet, or router firewall configuration restrictions. You can try moving the printer closer to the router or checking the router configuration before you try again.",
+    "0500_4025": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_4026": "Cloud access rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_4027": "Cloud access failed; this may be caused by network instability due to interference. You can try moving the printer closer to the router before you try again.",
+    "0500_4028": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_4029": "Cloud access is rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0500_402A": "Failed to connect to the router, which may be caused by wireless interference or being too far away from the router. Please try again or move the printer closer to the router and try again.",
+    "0500_402B": "Router connection failed due to incorrect password. Please check the password and try again.",
+    "0500_402C": "Failed to obtain IP address, which may be caused by wireless interference resulting in data transmission failure or DHCP address pool of the router being full. Please move the printer closer to the router and try again. If the issue persists, please check router settings to see whether the IP addresses have been exhausted.",
+    "0500_402D": "System exception.",
+    "0500_402E": "The system does not support the file system currently used by the Micro SD card. Please replace the Micro SD card or format the current Micro SD card to FAT32.",
+    "0500_402F": "The Micro SD card sector data is damaged. Please use the SD card repair tool to repair or format it. If it still cannot be identified, please replace the Micro SD card.",
+    "0500_4037": "Your sliced file is not compatible with current printer model. This file can't be printed on this printer.",
+    "0500_4038": "The nozzle diameter in sliced file is not consistent with the current nozzle setting. This file can't be printed.",
+    "0500_403A": "The current temperature is too low. In order to protect you and your printer. Printing task, moving axis and other operations are disabled. Please move the printer to an environment above 10 celsius degree.",
+    "0500_8013": "The print file is not available. Please check to see if the storage media has been removed.",
+    "0500_8030": "",
+    "0500_8036": "Your sliced file is not consistent with the current printer model. Continue?",
+    "0500_C010": "MicroSD Card read/write exception. please reinsert or replace MicroSD Card .",
+    "0500_C011": "",
+    "0501_4017": "Binding failed. Please retry or restart the printer and retry.",
+    "0501_4018": "Binding configuration information parsing failed,  please try again.",
+    "0501_4019": "The printer has already been bound. Please unbind it and try again.",
+    "0501_401A": "Cloud access failed. Possible reasons include network instability caused by interference, inability to access the internet, or router firewall configuration restrictions. You can try moving the printer closer to the router or checking the router configuration and then try again.",
+    "0501_401B": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_401C": "Cloud access is rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_401D": "Cloud access failed, which may be caused by network instability due to interference. You can try moving the printer closer to the router before you try again.",
+    "0501_401E": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_401F": "Authorization timed out. Please make sure that your phone or PC has access to the internet, and ensure that the Bambu Studio/Bambu Handy APP is running in the foreground during the binding operation.",
+    "0501_4020": "Cloud access rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_4021": "Cloud access failed, which may be caused by network instability due to interference. You can try moving the printer closer to the router before you try again.",
+    "0501_4022": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_4023": "Cloud access rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_4024": "Cloud access failed. Possible reasons include network instability caused by interference, inability to access the internet, or router firewall configuration restrictions. You can try moving the printer closer to the router or checking the router configuration before you try again.",
+    "0501_4025": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_4026": "Cloud access rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_4027": "Cloud access failed; this may be caused by network instability due to interference. You can try moving the printer closer to the router before you try again.",
+    "0501_4028": "Cloud response is invalid. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_4029": "Cloud access is rejected. If you have tried multiple times and are still failing, please contact customer service.",
+    "0501_4031": "Device discovery binding is in progress, and the QR code cannot be displayed on the screen. You can wait for the binding to finish or abort the device discovery binding process in the APP/Studio and retry scanning the QR code on the screen for binding.",
+    "0501_4032": "QR code binding is in progress, so device discovery binding cannot be performed. You can scan the QR code on the screen for binding or exit the QR code display page on screen and try device discovery binding.",
+    "0501_4033": "Your APP region is not matched with your printer; please download the APP in the corresponding region and register your account again.",
+    "0501_4034": "The slicing progress has not been updated for a long time, and the printing task has exited. Please confirm the parameters and reinitiate printing.",
+    "0501_4035": "The device is in the process of binding and cannot respond to new binding requests.",
+    "0501_4038": "The region settings do not match the printer; please check the printer's region settings.",
+    "0501_4039": "Device login has expired, please try to bind again.",
+    "0502_4001": "Current filament will be used in this print job. Settings cannot be changed.",
+    "0514_039": "Device login has expired; please try to bind again.",
+    "0700_4001": "The AMS has been disabled for a print, but it still has filament loaded. Please unload the AMS filament , and switch to the spool holder filament for printing.",
+    "0700_8001": "Failed to cut the filament. Please check the cutter. After troubleshooting, click the 'Retry' button.",
+    "0700_8002": "The cutter is stuck. Please make sure the cutter handle is out.",
+    "0700_8003": "Failed to pull out the filament from the extruder. This might be caused by clogged extruder or filament broken inside the extruder.",
+    "0700_8004": "AMS failed to pull back filament. This could be due to a stuck spool or the end of the filament being stuck in the path.",
+    "0700_8005": "The AMS failed to send out filament. You can clip the end of your filament flat, and reinsert. If this message persists, please check the PTFE tubes in AMS for any signs of wear and tear.",
+    "0700_8006": "Unable to feed filament into the extruder. This could be due to entangled filament or a stuck spool. If not, please check if the AMS PTFE tube is connected.",
+    "0700_8007": "Extruding filament failed. The extruder might be clogged.",
+    "0700_8010": "The AMS assist motor is overloaded. This could be due to entangled filament or a stuck spool.",
+    "0700_8011": "AMS filament ran out. Please insert a new filament into the same AMS slot.",
+    "0700_8012": "Failed to get AMS mapping table; please click 'Retry' to continue.",
+    "0700_8013": "Timeout purging old filament: Please check if the filament is stuck or the extruder is clogged. After troubleshooting, click the 'Retry' button.",
+    "0701_4001": "Filament is still loaded from the AMS after it has been disabled. Please unload the filament, load from the spool holder, and restart printing.",
+    "0701_8001": "Failed to cut the filament. Please check the cutter. After troubleshooting, click the 'Retry' button.",
+    "0701_8002": "The cutter is stuck. Please pull out the cutter handle and click the 'Retry' button.",
+    "0701_8003": "Failed to pull out the filament from the extruder. There may be an extruder clog or broken filament inside the extruder.",
+    "0701_8004": "AMS failed to pull back filament. This could be due to a stuck spool or the end of the filament being stuck in the path.",
+    "0701_8005": "The AMS failed to send out filament. You can clip the end of your filament flat, and reinsert. If this message persists, please check the PTFE tubes in AMS for any signs of wear and tear.",
+    "0701_8006": "Unable to feed filament into the extruder. This could be due to entangled filament or a stuck spool.",
+    "0701_8007": "Failed to extrude the filament. Please check if the extruder clogged. After troubleshooting, click the 'Retry' button.",
+    "0701_8010": "The AMS assist motor is overloaded. This could be due to entangled filament or a stuck spool.",
+    "0701_8011": "AMS filament ran out. Please insert a new filament into the same AMS slot.",
+    "0701_8012": "Failed to get AMS mapping table; please click 'Retry' to continue.",
+    "0701_8013": "Timeout purging old filament: Please check if the filament is stuck or the extruder is clogged. After troubleshooting, click the 'Retry' button.",
+    "0702_4001": "Filament is still loaded from the AMS after it has been disabled. Please unload the filament, load from the spool holder, and restart printing.",
+    "0702_8001": "Failed to cut the filament. Please check the cutter. After troubleshooting, click the 'Retry' button.",
+    "0702_8002": "The cutter is stuck. Please pull out the cutter handle and click the 'Retry' button.",
+    "0702_8003": "Failed to pull out the filament from the extruder. Please check whether the extruder is clogged or whether the filament is broken inside the extruder. After troubleshooting, click the 'Retry' button.",
+    "0702_8004": "Failed to pull back the filament from the toolhead to AMS. Please check whether the filament or the spool is stuck. After troubleshooting, click the 'Retry' button.",
+    "0702_8005": "The AMS failed to send out filament. You can clip the end of your filament flat, and reinsert. If this message persists, please check the PTFE tubes in AMS for any signs of wear and tear.",
+    "0702_8006": "Failed to feed the filament into the toolhead. Please check whether the filament or the spool is stuck. After troubleshooting, click the 'Retry' button.",
+    "0702_8007": "Failed to extrude the filament. Please check if the extruder clogged. After troubleshooting, click the 'Retry' button.",
+    "0702_8010": "The AMS assist motor is overloaded. This could be due to entangled filament or a stuck spool.",
+    "0702_8011": "AMS filament ran out. Please insert a new filament into the same AMS slot.",
+    "0702_8012": "Failed to get AMS mapping table; please click 'Retry' to continue.",
+    "0702_8013": "Timeout purging old filament: Please check if the filament is stuck or the extruder is clogged. After troubleshooting, click the 'Retry' button.",
+    "0703_4001": "Filament is still loaded from the AMS after it has been disabled. Please unload the filament, load from the spool holder, and restart printing.",
+    "0703_8001": "Failed to cut the filament. Please check the cutter. After troubleshooting, click the 'Retry' button.",
+    "0703_8002": "The cutter is stuck. Please pull out the cutter handle and click the 'Retry' button.",
+    "0703_8003": "Failed to pull out the filament from the extruder. Please check whether the extruder is clogged or whether the filament is broken inside the extruder. After troubleshooting, click the 'Retry' button.",
+    "0703_8004": "Failed to pull back the filament from the toolhead to AMS. Please check whether the filament or the spool is stuck. After troubleshooting, click the 'Retry' button.",
+    "0703_8005": "The AMS failed to send out filament. You can clip the end of your filament flat, and reinsert. If this message persists, please check the PTFE tubes in AMS for any signs of wear and tear.",
+    "0703_8006": "Failed to feed the filament into the toolhead. Please check whether the filament or the spool is stuck. After troubleshooting, click the 'Retry' button.",
+    "0703_8007": "Failed to extrude the filament. Please check if the extruder clogged. After troubleshooting, click the 'Retry' button.",
+    "0703_8010": "The AMS assist motor is overloaded. This could be due to entangled filament or a stuck spool.",
+    "0703_8011": "AMS filament ran out. Please insert a new filament into the same AMS slot.",
+    "0703_8012": "Failed to get AMS mapping table; please click 'Retry' to continue.",
+    "0703_8013": "Timeout purging old filament: Please check if the filament is stuck or the extruder is clogged. After troubleshooting, click the 'Retry' button.",
+    "07FF_4001": "Filament is still loaded from the AMS after it has been disabled. Please unload the filament, load from the spool holder, and restart printing.",
+    "07FF_8001": "Failed to cut the filament. Please check the cutter. After troubleshooting, click the 'Retry' button.",
+    "07FF_8002": "The cutter is stuck. Please pull out the cutter handle and click the 'Retry' button.",
+    "07FF_8003": "Please pull out the filament on the spool holder. If this message persists, please check to see if there is filament broken in the extruder. (Connect PTFE tube if you are about to use AMS)",
+    "07FF_8004": "Failed to pull back the filament from the toolhead to AMS. Please check whether the filament or the spool is stuck. After troubleshooting, click the 'retry' button.",
+    "07FF_8005": "Failed to feed the filament outside the AMS. Please clip the end of the filament flat and check to see if the spool is stuck. After troubleshooting, click the 'Retry' button.",
+    "07FF_8006": "Please feed filament into the PTFE tube until it can not be pushed any farther.",
+    "07FF_8007": "Please observe the nozzle. If the filament has been extruded, click 'Done'; if it is not, please push the filament forward slightly and then click 'Retry'.",
+    "07FF_8010": "The AMS assist motor is overloaded. This could be due to entangled filament or a stuck spool.",
+    "07FF_8011": "External filament has run out, please load a new filament.",
+    "07FF_8012": "Failed to get AMS mapping table; please click 'Retry' to continue.",
+    "07FF_8013": "Timeout purging old filament: Please check if the filament is stuck or the extruder is clogged. After troubleshooting, click the 'Retry' button.",
+    "07FF_C003": "Please pull out the filament on the spool holder. If this message persists, please check to see if there is filament broken in the extruder or PTFE Tube. (Connect PTFE tube if you are about to use AMS)",
+    "07FF_C006": "Please feed filament into the PTFE tube until it can not be pushed any farther.",
+    "07FF_C008": "Please pull out the filament on the spool holder. If this message persists, please check to see if there is filament broken in the extruder. (Connect PTFE tube if you are about to use AMS)",
+    "07FF_C009": "Please feed filament into the PTFE tube until it can not be pushed any farther.",
+    "07FF_C00A": "Please observe the nozzle. If the filament has been extruded, click 'Done'; if it is not, please push the filament forward slightly and then click 'Retry'.",
+    "0C00_402A": "",
+    "0C00_8001": "First layer defects were detected. If the defects are acceptable, click 'Resume' button to resume the print job.",
+    "0C00_8002": "Spaghetti failure was detected.",
+    "0C00_8005": "Purged filament has piled up in the waste chute, which may cause a tool head collision.",
+    "0C00_8009": "Build plate localization marker was not found.",
+    "0C00_800A": "The detected build plate is not the same as in G-code.",
+    "0C00_C003": "Possible defects were detected in the first layer.",
+    "0C00_C004": "Possible spaghetti failure was detected.",
+    "0C00_C006": "Purged filament may have piled up in the waste chute.",
+    "1000_C001": "High bed temperature may lead to filament clogging in the nozzle. You may open the chamber door.",
+    "1000_C002": "Printing CF material with stainless steel may cause nozzle damage.",
+    "1000_C003": "Enabling traditional timelapse might lead to defects. Please enable it as needed?",
+    "1001_C001": "Timelapse is not supported because Spiral vase is enabled in slicing presets.",
+    "1001_C002": "Timelapse is not supported because Print sequence is set to 'By object'.",
+    "1200_4001": "Filament is still loaded from the AMS when it has been disabled. Please unload AMS filament, load from spool holder, and restart print job.",
+    "1200_8001": "Cutting the filament failed. Please check to see if the cutter is stuck. Refer to the Assistant for solutions.",
+    "1200_8002": "The cutter is stuck. Please pull out the cutter handle and click the 'Retry' button.",
+    "1200_8003": "Failed to pull out the filament from the extruder. Please check whether the extruder is clogged or whether the filament is broken inside the extruder. After troubleshooting, click the 'Retry' button.",
+    "1200_8004": "Failed to pull back the filament from the toolhead. Please check whether the filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1200_8005": "Failed to feed the filament. Please load the filament, then click the 'Retry' button.",
+    "1200_8006": "Unable to feed filament into the extruder. This could be due to entangled filament or a stuck spool. If not, please check if the AMS PTFE tube is connected.",
+    "1200_8007": "Failed to extrude the filament. This might be caused by clogged extruder or stuck filament. Refer to the Assistant for solutions.",
+    "1200_8010": "Filament or spool may be stuck.",
+    "1200_8011": "AMS filament ran out. Please insert a new filament into the same AMS slot.",
+    "1200_8012": "Failed to get AMS mapping table. Please click the 'Retry' button to continue.",
+    "1200_8013": "Timeout while purging old filament. Please check if the filament is stuck or the extruder clogged. After troubleshooting, click the 'Retry' button.",
+    "1200_8014": "The filament location in the toolhead was not found. Refer to the Assistant for solutions.",
+    "1200_8015": "Failed to pull out the filament from the toolhead. Please check if the filament is stuck, or the filament is broken inside the extruder or PTFE tube.",
+    "1200_8016": "The extruder is not extruding normally. Refer to the Assistant for troubleshooting. There may be defects in this layer, you may resume if the defects are acceptable.",
+    "1201_4001": "Filament is still loaded from the AMS when it has been disabled. Please unload AMS filament, load from spool holder, and restart print job.",
+    "1201_8001": "Failed to cut the filament. Please check the cutter. After troubleshooting, click the 'Retry' button.",
+    "1201_8002": "The cutter is stuck. Please pull out the cutter handle and click the 'Retry' button.",
+    "1201_8003": "Failed to pull out the filament from the extruder. Please check whether the extruder is clogged or whether the filament is broken inside the extruder. After troubleshooting, click the 'Retry' button.",
+    "1201_8004": "Failed to pull back the filament from the toolhead. Please check whether the filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1201_8005": "Failed to feed the filament. Please load the filament and then click the 'Retry' button.",
+    "1201_8006": "Failed to feed the filament into the toolhead. Please check whether the filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1201_8007": "Failed to extrude the filament. The extruder may be clogged or the filament may be stuck; please refer to HMS. After troubleshooting, click 'Retry' button.",
+    "1201_8010": "Please check if the spool or filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1201_8011": "AMS filament has run out. Please insert a new filament into the same AMS slot.",
+    "1201_8012": "Failed to get AMS mapping table; please click the 'Retry' button to continue.",
+    "1201_8013": "Timeout while purging old filament. Please check if the filament is stuck or the extruder clogged. After troubleshooting, click the 'Retry' button.",
+    "1201_8014": "Failed to check the filament location in the tool head; please refer to the HMS. After troubleshooting, click the 'Retry' button.",
+    "1201_8015": "Failed to pull back the filament from the toolhead. Please check if the filament is stuck or the filament is broken inside the extruder. After troubleshooting, click the 'Retry' button.",
+    "1201_8016": "The extruder is not extruding normally; please refer to the HMS. After trouble shooting. If the defects are acceptable, please click 'Retry' button.",
+    "1202_4001": "Filament is still loaded from the AMS when it has been disabled. Please unload AMS filament, load from spool holder, and restart print job.",
+    "1202_8001": "Failed to cut the filament. Please check the cutter. After troubleshooting, click the 'Retry' button.",
+    "1202_8002": "The cutter is stuck. Please pull out the cutter handle and click the 'Retry' button.",
+    "1202_8003": "Failed to pull out the filament from the extruder. Please check whether the extruder is clogged or whether the filament is broken inside the extruder. After troubleshooting, click the 'Retry' button.",
+    "1202_8004": "Failed to pull back the filament from the toolhead. Please check whether the filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1202_8005": "Failed to feed the filament. Please load the filament, then click the 'Retry' button.",
+    "1202_8006": "Failed to feed the filament into the toolhead. Please check whether the filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1202_8007": "Failed to extrude the filament. The extruder may be clogged or the filament may be stuck; please refer to HMS. After troubleshooting, click 'Retry' button.",
+    "1202_8010": "Please check if the spool or filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1202_8011": "AMS filament has run out. Please insert a new filament into the same AMS slot.",
+    "1202_8012": "Failed to get AMS mapping table; please click the 'Retry' button to continue.",
+    "1202_8013": "Timeout while purging old filament. Please check if the filament is stuck or the extruder clogged. After troubleshooting, click the 'Retry' button.",
+    "1202_8014": "Failed to check the filament location in the tool head; please refer to the HMS. After troubleshooting, click the 'Retry' button.",
+    "1202_8015": "Failed to pull back the filament from the toolhead. Please check if the filament is stuck or is broken inside the extruder. After troubleshooting, click the 'Retry' button.",
+    "1202_8016": "The extruder is not extruding normally; please refer to the HMS. After trouble shooting. If the defects are acceptable, please click 'Retry' button.",
+    "1203_4001": "Filament is still loaded from the AMS when it has been disabled. Please unload AMS filament, load from spool holder, and restart print job.",
+    "1203_8001": "Failed to cut the filament. Please check the cutter. After troubleshooting, click the 'Retry' button.",
+    "1203_8002": "The cutter is stuck. Please pull out the cutter handle and click the 'Retry' button.",
+    "1203_8003": "Failed to pull out the filament from the extruder. Please check whether the extruder is clogged or whether the filament is broken inside the extruder. After troubleshooting, click the 'Retry' button.",
+    "1203_8004": "Failed to pull back the filament from the toolhead. Please check whether the filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1203_8005": "Failed to feed the filament. Please load the filament, then click the 'Retry' button.",
+    "1203_8006": "Failed to feed the filament into the toolhead. Please check whether the filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1203_8007": "Failed to extrude the filament. The extruder may be clogged or the filament may be stuck; please refer to HMS. After troubleshooting, click 'Retry' button.",
+    "1203_8010": "Please check if the spool or filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "1203_8011": "AMS filament has run out. Please insert a new filament into the same AMS slot.",
+    "1203_8012": "Failed to get AMS mapping table; please click the 'Retry' button to continue.",
+    "1203_8013": "Timeout while purging old filament. Please check if the filament is stuck or the extruder clogged. After troubleshooting, click the 'Retry' button.",
+    "1203_8014": "Failed to check the filament location in the tool head; please refer to the HMS. After troubleshooting, click the 'Retry' button.",
+    "1203_8015": "Failed to pull back the filament from the toolhead. Please check if the filament is stuck or is broken inside the extruder. After troubleshooting, click the 'Retry' button.",
+    "1203_8016": "The extruder is not extruding normally; please refer to the HMS. After trouble shooting. If the defects are acceptable, please click 'Retry' button.",
+    "12FF_4001": "Filament is still loaded from the AMS when it has been disabled. Please unload AMS filament, load from spool holder, and restart print job.",
+    "12FF_8001": "Failed to cut the filament. Please check the cutter. After troubleshooting, click the 'Retry' button.",
+    "12FF_8002": "The cutter is stuck. Please pull out the cutter handle and click the 'Retry' button.",
+    "12FF_8003": "Please pull out the filament on the spool holder. If this message persists, please check to see if there is filament broken in the extruder or PTFE Tube. (Connect PTFE tube if you are about to use AMS)",
+    "12FF_8004": "Failed to pull back the filament from the toolhead. Please check whether the filament is stuck. After troubleshooting, click the 'Retry' button.",
+    "12FF_8005": "Failed to feed the filament. Please load the filament, then click the 'Retry' button.",
+    "12FF_8006": "Please feed filament into the PTFE tube until it can not be pushed any farther.",
+    "12FF_8007": "Check nozzle. Click 'Done' if filament was extruded, otherwise push filament forward slightly and click 'Retry.'",
+    "12FF_8010": "Please check if the filament or the spool is stuck.",
+    "12FF_8011": "AMS filament has run out. Please insert a new filament into the same AMS slot.",
+    "12FF_8012": "Failed to get AMS mapping table; please click the 'Retry' button to continue.",
+    "12FF_8013": "Timeout while purging old filament. Please check if the filament is stuck or the extruder clogged. After troubleshooting, click the 'Retry' button.",
+    "12FF_C003": "Please pull out the filament on the spool holder. If this message persists, please check to see if there is filament broken in the extruder or PTFE Tube. (Connect PTFE tube if you are about to use AMS)",
+    "12FF_C006": "Please feed filament into the PTFE tube until it can not be pushed any farther.",
+}

octoprint_bambu_printer/printer/pybambu/filaments.json

@@ -15,6 +15,7 @@
     "GFB01": "Bambu ASA",
     "GFB02": "Bambu ASA-Aero",
     "GFB50": "Bambu ABS-GF",
+    "GFB51": "Bambu ASA-CF",
     "GFB60": "PolyLite ABS",
     "GFB61": "PolyLite ASA",
     "GFB98": "Generic ASA",
@@ -26,6 +27,7 @@
     "GFG02": "Bambu PETG HF",
     "GFG50": "Bambu PETG-CF",
     "GFG60": "PolyLite PETG",
+    "GFG96": "Generic PETG HF",
     "GFG97": "Generic PCTG",
     "GFG98": "Generic PETG-CF",
     "GFG99": "Generic PETG",
@@ -34,6 +36,13 @@
     "GFL03": "eSUN PLA+",
     "GFL04": "Overture PLA",
     "GFL05": "Overture Matte PLA",
+    "GFL06": "Fiberon PETG-ESD",
+    "GFL50": "Fiberon PA6-CF",
+    "GFL51": "Fiberon PA6-GF",
+    "GFL52": "Fiberon PA12-CF",
+    "GFL53": "Fiberon PA612-CF",
+    "GFL54": "Fiberon PET-CF",
+    "GFL55": "Fiberon PETG-rCF",
     "GFL95": "Generic PLA High Speed",
     "GFL96": "Generic PLA Silk",
     "GFL98": "Generic PLA-CF",
@@ -41,6 +50,7 @@
     "GFN03": "Bambu PA-CF",
     "GFN04": "Bambu PAHT-CF",
     "GFN05": "Bambu PA6-CF",
+    "GFN06": "Bambu PPA-CF",
     "GFN08": "Bambu PA6-GF",
     "GFN96": "Generic PPA-GF",
     "GFN97": "Generic PPA-CF",
@@ -64,9 +74,12 @@
     "GFS98": "Generic HIPS",
     "GFS99": "Generic PVA",
     "GFT01": "Bambu PET-CF",
+    "GFT02": "Bambu PPS-CF",
     "GFT97": "Generic PPS",
     "GFT98": "Generic PPS-CF",
     "GFU00": "Bambu TPU 95A HF",
     "GFU01": "Bambu TPU 95A",
+    "GFU02": "Bambu TPU for AMS",
+    "GFU98": "Generic TPU for AMS",
     "GFU99": "Generic TPU"
-}
+}

octoprint_bambu_printer/printer/pybambu/models.py

@@ -22,6 +22,7 @@ from .utils import (
     get_generic_AMS_HMS_error_code,
     get_HMS_severity,
     get_HMS_module,
+    set_temperature_to_gcode,
 )
 from .const import (
     LOGGER,
@@ -32,6 +33,7 @@ from .const import (
     SPEED_PROFILE,
     GCODE_STATE_OPTIONS,
     PRINT_TYPE_OPTIONS,
+    TempEnum,
 )
 from .commands import (
     CHAMBER_LIGHT_ON,
@@ -42,7 +44,7 @@ from .commands import (
 class Device:
     def __init__(self, client):
         self._client = client
-        self.temperature = Temperature()
+        self.temperature = Temperature(client = client)
         self.lights = Lights(client = client)
         self.info = Info(client = client)
         self.print_job = PrintJob(client = client)
@@ -53,7 +55,7 @@ class Device:
         self.external_spool = ExternalSpool(client = client)
         self.hms = HMSList(client = client)
         self.print_error = PrintErrorList(client = client)
-        self.camera = Camera()
+        self.camera = Camera(client = client)
         self.home_flag = HomeFlag(client=client)
         self.push_all_data = None
         self.get_version_data = None
@@ -77,8 +79,7 @@ class Device:
         send_event = send_event | self.camera.print_update(data = data)
         send_event = send_event | self.home_flag.print_update(data = data)
 
-        if send_event and self._client.callback is not None:
-            self._client.callback("event_printer_data_update")
+        self._client.callback("event_printer_data_update")
 
         if data.get("msg", 0) == 0:
             self.push_all_data = data
@@ -90,6 +91,16 @@ class Device:
         if data.get("command") == "get_version":
             self.get_version_data = data
 
+    def _supports_temperature_set(self):
+        # When talking to the Bambu cloud mqtt, setting the temperatures is allowed.
+        if self.info.mqtt_mode == "bambu_cloud":
+            return True
+        # X1* have not yet blocked setting the temperatures when in nybrid connection mode.
+        if self.info.device_type == "X1" or self.info.device_type == "X1C" or self.info.device_type == "X1E":
+            return True
+        # What's left is P1 and A1 printers that we are connecting by local mqtt. These are supported only in pure Lan Mode.
+        return not self._client.bambu_cloud.bambu_connected
+
     def supports_feature(self, feature):
         if feature == Features.AUX_FAN:
             return self.info.device_type != "A1" and self.info.device_type != "A1MINI"
@@ -126,9 +137,11 @@ class Device:
         elif feature == Features.AMS_FILAMENT_REMAINING:
             # Technically this is not the AMS Lite but that's currently tied to only these printer types.
             return self.info.device_type != "A1" and self.info.device_type != "A1MINI"
+        elif feature == Features.SET_TEMPERATURE:
+            return self._supports_temperature_set()
 
         return False
-
+    
     def get_active_tray(self):
         if self.supports_feature(Features.AMS):
             if self.ams.tray_now == 255:
@@ -179,21 +192,19 @@ class Lights:
         self.work_light = \
             search(data.get("lights_report", []), lambda x: x.get('node', "") == "work_light",
                    {"mode": self.work_light}).get("mode")
-
+        
         return (old_data != f"{self.__dict__}")
 
     def TurnChamberLightOn(self):
         self.chamber_light = "on"
         self.chamber_light_override = "on"
-        if self._client.callback is not None:
-            self._client.callback("event_light_update")
+        self._client.callback("event_light_update")
         self._client.publish(CHAMBER_LIGHT_ON)
 
     def TurnChamberLightOff(self):
         self.chamber_light = "off"
         self.chamber_light_override = "off"
-        if self._client.callback is not None:
-            self._client.callback("event_light_update")
+        self._client.callback("event_light_update")
         self._client.publish(CHAMBER_LIGHT_OFF)
 
 
@@ -205,7 +216,8 @@ class Camera:
     rtsp_url: str
     timelapse: str
 
-    def __init__(self):
+    def __init__(self, client):
+        self._client = client
         self.recording = ''
         self.resolution = ''
         self.rtsp_url = None
@@ -227,8 +239,11 @@ class Camera:
         self.timelapse = data.get("ipcam", {}).get("timelapse", self.timelapse)
         self.recording = data.get("ipcam", {}).get("ipcam_record", self.recording)
         self.resolution = data.get("ipcam", {}).get("resolution", self.resolution)
-        self.rtsp_url = data.get("ipcam", {}).get("rtsp_url", self.rtsp_url)
-
+        if self._client._enable_camera:
+            self.rtsp_url = data.get("ipcam", {}).get("rtsp_url", self.rtsp_url)
+        else:
+            self.rtsp_url = None
+        
         return (old_data != f"{self.__dict__}")
 
 @dataclass
@@ -240,7 +255,8 @@ class Temperature:
     nozzle_temp: int
     target_nozzle_temp: int
 
-    def __init__(self):
+    def __init__(self, client):
+        self._client = client
         self.bed_temp = 0
         self.target_bed_temp = 0
         self.chamber_temp = 0
@@ -255,9 +271,23 @@ class Temperature:
         self.chamber_temp = round(data.get("chamber_temper", self.chamber_temp))
         self.nozzle_temp = round(data.get("nozzle_temper", self.nozzle_temp))
         self.target_nozzle_temp = round(data.get("nozzle_target_temper", self.target_nozzle_temp))
-
+        
         return (old_data != f"{self.__dict__}")
 
+    def set_target_temp(self, temp: TempEnum, temperature: int):
+        command = set_temperature_to_gcode(temp, temperature)
+
+        # if type == TempEnum.HEATBED:
+        #     self.bed_temp = temperature
+        # elif type == TempEnum.NOZZLE:
+        #     self.nozzle_temp = temperature
+
+        LOGGER.debug(command)
+        self._client.publish(command)
+
+        self._client.callback("event_printer_data_update")
+
+
 @dataclass
 class Fans:
     """Return all fan related info"""
@@ -316,7 +346,7 @@ class Fans:
                 self._cooling_fan_speed_override_time = None
         self._heatbreak_fan_speed = data.get("heatbreak_fan_speed", self._heatbreak_fan_speed)
         self._heatbreak_fan_speed_percentage = fan_percentage(self._heatbreak_fan_speed)
-
+        
         return (old_data != f"{self.__dict__}")
 
     def set_fan_speed(self, fan: FansEnum, percentage: int):
@@ -337,8 +367,7 @@ class Fans:
         LOGGER.debug(command)
         self._client.publish(command)
 
-        if self._client.callback is not None:
-            self._client.callback("event_printer_data_update")
+        self._client.callback("event_printer_data_update")
 
     def get_fan_speed(self, fan: FansEnum) -> int:
         if fan == FansEnum.PART_COOLING:
@@ -483,8 +512,7 @@ class PrintJob:
         currently_idle = self.gcode_state == "IDLE" or self.gcode_state == "FAILED" or self.gcode_state == "FINISH"
 
         if previously_idle and not currently_idle:
-            if self._client.callback is not None:
-               self._client.callback("event_print_started")
+            self._client.callback("event_print_started")
 
             # Generate the start_time for P1P/S when printer moves from idle to another state. Original attempt with remaining time
             # becoming non-zero didn't work as it never bounced to zero in at least the scenario where a print was canceled.
@@ -508,20 +536,17 @@ class PrintJob:
         isCanceledPrint = False
         if data.get("print_error") == 50348044 and self.print_error == 0:
             isCanceledPrint = True
-            if self._client.callback is not None:
-               self._client.callback("event_print_canceled")
+            self._client.callback("event_print_canceled")
         self.print_error = data.get("print_error", self.print_error)
 
         # Handle print failed
         if previous_gcode_state != "unknown" and previous_gcode_state != "FAILED" and self.gcode_state == "FAILED":
             if not isCanceledPrint:
-                if self._client.callback is not None:
-                   self._client.callback("event_print_failed")
+                self._client.callback("event_print_failed")
 
         # Handle print finish
         if previous_gcode_state != "unknown" and previous_gcode_state != "FINISH" and self.gcode_state == "FINISH":
-            if self._client.callback is not None:
-               self._client.callback("event_print_finished")
+            self._client.callback("event_print_finished")
 
         if currently_idle and not previously_idle and previous_gcode_state != "unknown":
             if self.start_time != None:
@@ -666,7 +691,7 @@ class Info:
         self.sw_ver = "unknown"
         self.online = False
         self.new_version_state = 0
-        self.mqtt_mode = "local" if self._client.local_mqtt else "bambu_cloud"
+        self.mqtt_mode = "local" if self._client._local_mqtt else "bambu_cloud"
         self.nozzle_diameter = 0
         self.nozzle_type = "unknown"
         self.usage_hours = client._usage_hours
@@ -674,8 +699,7 @@ class Info:
     def set_online(self, online):
         if self.online != online:
             self.online = online
-            if self._client.callback is not None:
-                self._client.callback("event_printer_data_update")
+            self._client.callback("event_printer_data_update")
 
     def info_update(self, data):
 
@@ -704,8 +728,7 @@ class Info:
         LOGGER.debug(f"Device is {self.device_type}")
         self.hw_ver = get_hw_version(modules, self.hw_ver)
         self.sw_ver = get_sw_version(modules, self.sw_ver)
-        if self._client.callback is not None:
-            self._client.callback("event_printer_info_update")
+        self._client.callback("event_printer_info_update")
 
     def print_update(self, data) -> bool:
         old_data = f"{self.__dict__}"
@@ -866,7 +889,7 @@ class AMSList:
                 index = int(name[4])
             elif name.startswith("ams_f1/"):
                 index = int(name[7])
-
+            
             if index != -1:
                 # Sometimes we get incomplete version data. We have to skip if that occurs since the serial number is
                 # required as part of the home assistant device identity.
@@ -891,8 +914,7 @@ class AMSList:
         data_changed = data_changed or (old_data != f"{self.__dict__}")
 
         if data_changed:
-            if self._client.callback is not None:
-                self._client.callback("event_ams_info_update")
+            self._client.callback("event_ams_info_update")
 
     def print_update(self, data) -> bool:
         old_data = f"{self.__dict__}"
@@ -1041,7 +1063,7 @@ class AMSTray:
             self.tag_uid = data.get('tag_uid', self.tag_uid)
             self.tray_uuid = data.get('tray_uuid', self.tray_uuid)
             self.k = data.get('k', self.k)
-
+        
         return (old_data != f"{self.__dict__}")
 
 
@@ -1110,7 +1132,7 @@ class Speed:
         self._id = int(data.get("spd_lvl", self._id))
         self.name = get_speed_name(self._id)
         self.modifier = int(data.get("spd_mag", self.modifier))
-
+        
         return (old_data != f"{self.__dict__}")
 
     def SetSpeed(self, option: str):
@@ -1121,8 +1143,7 @@ class Speed:
                 command = SPEED_PROFILE_TEMPLATE
                 command['print']['param'] = f"{id}"
                 self._client.publish(command)
-                if self._client.callback is not None:
-                    self._client.callback("event_speed_update")
+                self._client.callback("event_speed_update")
 
 
 @dataclass
@@ -1162,7 +1183,7 @@ class HMSList:
         self._count = 0
         self._errors = {}
         self._errors["Count"] = 0
-
+        
     def print_update(self, data) -> bool:
         # Example payload:
         # "hms": [
@@ -1187,7 +1208,8 @@ class HMSList:
                 attr = int(hms['attr'])
                 code = int(hms['code'])
                 hms_notif = HMSNotification(attr=attr, code=code)
-                errors[f"{index}-Error"] = f"HMS_{hms_notif.hms_code}: {get_HMS_error_text(hms_notif.hms_code)}"
+                errors[f"{index}-Code"] = f"HMS_{hms_notif.hms_code}"
+                errors[f"{index}-Error"] = get_HMS_error_text(hms_notif.hms_code)
                 errors[f"{index}-Wiki"] = hms_notif.wiki_url
                 errors[f"{index}-Severity"] = hms_notif.severity
                 #LOGGER.debug(f"HMS error for '{hms_notif.module}' and severity '{hms_notif.severity}': HMS_{hms_notif.hms_code}")
@@ -1198,17 +1220,16 @@ class HMSList:
                 self._errors = errors
                 if self._count != 0:
                     LOGGER.warning(f"HMS ERRORS: {errors}")
-                if self._client.callback is not None:
-                    self._client.callback("event_hms_errors")
+                self._client.callback("event_printer_error")
                 return True
-
+        
         return False
-
+    
     @property
     def errors(self) -> dict:
         #LOGGER.debug(f"PROPERTYCALL: get_hms_errors")
         return self._errors
-
+    
     @property
     def error_count(self) -> int:
         return self._count
@@ -1217,16 +1238,14 @@ class HMSList:
 class PrintErrorList:
     """Return all print_error related info"""
     _error: dict
-    _count: int
 
     def __init__(self, client):
         self._error = None
-        self._count = 0
         self._client = client
-
+        
     def print_update(self, data) -> bool:
         # Example payload:
-        # "print_error": 117473286
+        # "print_error": 117473286 
         # So this is 07008006 which we make more human readable to 0700-8006
         # https://e.bambulab.com/query.php?lang=en
         # 'Unable to feed filament into the extruder. This could be due to entangled filament or a stuck spool. If not, please check if the AMS PTFE tube is connected.'
@@ -1238,22 +1257,21 @@ class PrintErrorList:
                 hex_conversion = f'0{int(print_error_code):x}'
                 print_error_code_hex = hex_conversion[slice(0,4,1)] + "_" + hex_conversion[slice(4,8,1)]
                 errors = {}
-                errors[f"Code"] = f"{print_error_code_hex.upper()}"
-                errors[f"Error"] = f"{print_error_code_hex.upper()}: {get_print_error_text(print_error_code)}"
+                errors[f"code"] = print_error_code_hex.upper()
+                errors[f"error"] = get_print_error_text(print_error_code)
                 # LOGGER.warning(f"PRINT ERRORS: {errors}") # This will emit a message to home assistant log every 1 second if enabled
 
             if self._error != errors:
                 self._error = errors
-                if self._client.callback is not None:
-                    self._client.callback("event_print_error")
+                self._client.callback("event_print_error")
 
         # We send the error event directly so always return False for the general data event.
         return False
-
+    
     @property
     def error(self) -> dict:
         return self._error
-
+    
     @property
     def on(self) -> int:
         return self._error is not None
@@ -1296,13 +1314,23 @@ class ChamberImage:
     def __init__(self, client):
         self._client = client
         self._bytes = bytearray()
+        self._image_last_updated = datetime.now()
 
     def set_jpeg(self, bytes):
         self._bytes = bytes
+        self._image_last_updated = datetime.now()
+        self._client.callback("event_printer_chamber_image_update")
 
     def get_jpeg(self) -> bytearray:
         return self._bytes.copy()
-
+    
+    def get_last_update_time(self) -> datetime:
+        return self._image_last_updated
+    
+    @property
+    def available(self):
+        return self._client._enable_camera 
+    
 @dataclass
 class CoverImage:
     """Returns the cover image from the Bambu API"""
@@ -1311,13 +1339,12 @@ class CoverImage:
         self._client = client
         self._bytes = bytearray()
         self._image_last_updated = datetime.now()
-        if self._client.callback is not None:
-            self._client.callback("event_printer_cover_image_update")
+        self._client.callback("event_printer_cover_image_update")
 
     def set_jpeg(self, bytes):
         self._bytes = bytes
         self._image_last_updated = datetime.now()
-
+    
     def get_jpeg(self) -> bytearray:
         return self._bytes
 
@@ -1330,7 +1357,7 @@ class HomeFlag:
     """Contains parsed _values from the homeflag sensor"""
     _value: int
     _sw_ver: str
-    _device_type: str
+    _device_type: str 
 
     def __init__(self, client):
         self._value = 0
@@ -1359,7 +1386,7 @@ class HomeFlag:
     def door_open_available(self) -> bool:
         if not self._client._device.supports_feature(Features.DOOR_SENSOR):
             return False
-
+        
         if (self._device_type in ["X1", "X1C"] and version.parse(self._sw_ver) < version.parse("01.07.00.00")):
             return False
 
@@ -1368,7 +1395,7 @@ class HomeFlag:
     @property
     def x_axis_homed(self) -> bool:
         return (self._value & Home_Flag_Values.X_AXIS) != 0
-
+    
     @property
     def y_axis_homed(self) -> bool:
         return (self._value & Home_Flag_Values.Y_AXIS) != 0
@@ -1404,7 +1431,7 @@ class HomeFlag:
     @property
     def sdcard_normal(self) -> bool:
         return self.sdcard_present and (self._value & Home_Flag_Values.HAS_SDCARD_ABNORMAL) != SdcardState.HAS_SDCARD_ABNORMAL
-
+    
     @property
     def ams_auto_switch_filament(self) -> bool:
         return (self._value & Home_Flag_Values.AMS_AUTO_SWITCH) != 0
@@ -1420,11 +1447,11 @@ class HomeFlag:
     @property
     def supports_motor_noise_calibration(self) -> bool:
         return (self._value & Home_Flag_Values.SUPPORTS_MOTOR_CALIBRATION) != 0
-
+    
     @property
     def p1s_upgrade_supported(self) -> bool:
         return (self._value & Home_Flag_Values.SUPPORTED_PLUS) !=  0
-
+    
     @property
     def p1s_upgrade_installed(self) -> bool:
         return (self._value & Home_Flag_Values.INSTALLED_PLUS) !=  0
@@ -1449,7 +1476,7 @@ class SlicerSettings:
 
     def update(self):
         self.custom_filaments = {}
-        if self._client.bambu_cloud.auth_token != "" and self._client.local_mqtt is False:
+        if self._client.bambu_cloud.auth_token != "":
             LOGGER.debug("Loading slicer settings")
             slicer_settings = self._client.bambu_cloud.get_slicer_settings()
             if slicer_settings is not None:

octoprint_bambu_printer/printer/pybambu/utils.py

@@ -11,8 +11,9 @@ from .const import (
     HMS_SEVERITY_LEVELS,
     HMS_MODULES,
     LOGGER,
+    BAMBU_URL,
     FansEnum,
-    BAMBU_URL
+    TempEnum
 )
 from .commands import SEND_GCODE_TEMPLATE
 
@@ -49,6 +50,18 @@ def fan_percentage_to_gcode(fan: FansEnum, percentage: int):
     return command
 
 
+def set_temperature_to_gcode(temp: TempEnum, temperature: int):
+    """Converts a temperature to the gcode command to set that"""
+    if temp == TempEnum.NOZZLE:
+        tempCommand = "M104"
+    elif temp == TempEnum.HEATBED:
+        tempCommand = "M140"
+
+    command = SEND_GCODE_TEMPLATE
+    command['print']['param'] = f"{tempCommand} S{temperature}\n"
+    return command
+
+
 def to_whole(number):
     if not number:
         return 0

setup.py

@@ -14,7 +14,7 @@ plugin_package = "octoprint_bambu_printer"
 plugin_name = "OctoPrint-BambuPrinter"
 
 # The plugin's version. Can be overwritten within OctoPrint's internal data via __plugin_version__ in the plugin module
-plugin_version = "0.1.8rc11"
+plugin_version = "0.1.8rc13"
 
 # The plugin's description. Can be overwritten within OctoPrint's internal data via __plugin_description__ in the plugin
 # module
@@ -33,7 +33,7 @@ plugin_url = "https://github.com/jneilliii/OctoPrint-BambuPrinter"
 plugin_license = "AGPLv3"
 
 # Any additional requirements besides OctoPrint should be listed here
-plugin_requires = ["paho-mqtt<2", "python-dateutil", "curl_cffi"]
+plugin_requires = ["paho-mqtt<2", "python-dateutil", "cloudscraper"]
 
 ### --------------------------------------------------------------------------------------------------------------------
 ### More advanced options that you usually shouldn't have to touch follow after this point