e455764079
[ver] v1.1f update due to tweaks to interface from new parking override control. [new] Parking motion override control via new `M56 P0` and `M56 P1` command, which disables and enables the parking motion, respectively. Requires ENABLE_PARKING_OVERRIDE_CONTROL and PARKING_ENABLE enabled in config.h. Primarily for OEMs. [new] `M56` appears in the $G report when enabled. [new] Five new build info identification letters. Some were missing and a couple are new. Updated the CSV and documentation to reflect these new items. [new] Spindle enable pin configuration option to alter its behavior based on how certain lasers work. By default, Grbl treats the enable pin separately and leaves it on when S is 0. The new option turns the enable pin on and off with S>0 and S=0. This only is in effect when a user enables the USE_SPINDLE_DIR_AS_ENABLE_PIN option. [fix] M4 is now allowed to work when USE_SPINDLE_DIR_AS_ENABLE_PIN is enabled. Previously this was blocked and was problematic for laser folks using M4. [fix] Properly declared system variables as extern. Not sure how that went unnoticed or why it worked up until now but it has. [fix] EXTREMELY RARE. When AMASS is intentionally disabled and sent a motion command that is _one step_ in length, Grbl would not actuate the step due to numerical round-off. Applied a fix to prevent the round-off issue. [fix] Added a compile-time check for AMASS settings to make sure that the numerical round-off issue doesn’t effect it. This would only happen if someone set AMASS max levels to zero. It does not effect AMASS with its current defaults. [fix] Wrapped the mc_parking_motion() function in an ifdef for porting purposes. [fix] Fixed an issue when in inverse time mode and G0’s would require a F word. This was not correct. [fix] Added a note in the defaults.h file that MAX_TRAVEL values must be positive. Some users were setting this negative and it was causing issues.
67 lines
2.6 KiB
C
67 lines
2.6 KiB
C
/*
|
|
motion_control.h - high level interface for issuing motion commands
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2011-2016 Sungeun K. Jeon for Gnea Research LLC
|
|
Copyright (c) 2009-2011 Simen Svale Skogsrud
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#ifndef motion_control_h
|
|
#define motion_control_h
|
|
|
|
|
|
// System motion commands must have a line number of zero.
|
|
#define HOMING_CYCLE_LINE_NUMBER 0
|
|
#define PARKING_MOTION_LINE_NUMBER 0
|
|
|
|
#define HOMING_CYCLE_ALL 0 // Must be zero.
|
|
#define HOMING_CYCLE_X bit(X_AXIS)
|
|
#define HOMING_CYCLE_Y bit(Y_AXIS)
|
|
#define HOMING_CYCLE_Z bit(Z_AXIS)
|
|
|
|
|
|
// Execute linear motion in absolute millimeter coordinates. Feed rate given in millimeters/second
|
|
// unless invert_feed_rate is true. Then the feed_rate means that the motion should be completed in
|
|
// (1 minute)/feed_rate time.
|
|
void mc_line(float *target, plan_line_data_t *pl_data);
|
|
|
|
// Execute an arc in offset mode format. position == current xyz, target == target xyz,
|
|
// offset == offset from current xyz, axis_XXX defines circle plane in tool space, axis_linear is
|
|
// the direction of helical travel, radius == circle radius, is_clockwise_arc boolean. Used
|
|
// for vector transformation direction.
|
|
void mc_arc(float *target, plan_line_data_t *pl_data, float *position, float *offset, float radius,
|
|
uint8_t axis_0, uint8_t axis_1, uint8_t axis_linear, uint8_t is_clockwise_arc);
|
|
|
|
// Dwell for a specific number of seconds
|
|
void mc_dwell(float seconds);
|
|
|
|
// Perform homing cycle to locate machine zero. Requires limit switches.
|
|
void mc_homing_cycle(uint8_t cycle_mask);
|
|
|
|
// Perform tool length probe cycle. Requires probe switch.
|
|
uint8_t mc_probe_cycle(float *target, plan_line_data_t *pl_data, uint8_t parser_flags);
|
|
|
|
// Handles updating the override control state.
|
|
void mc_override_ctrl_update(uint8_t override_state);
|
|
|
|
// Plans and executes the single special motion case for parking. Independent of main planner buffer.
|
|
void mc_parking_motion(float *parking_target, plan_line_data_t *pl_data);
|
|
|
|
// Performs system reset. If in motion state, kills all motion and sets system alarm.
|
|
void mc_reset();
|
|
|
|
#endif
|