grbl-LPC-CoreXY/doc/log/commit_log_v1.1.txt

----------------
Date: 2016-10-12
Author: Sonny Jeon
Subject: Spindle speed bug fix.

- Spindle speed updating wasn’t working in the g-code parser due to
some borked up logic on my part. Fixed it and should be operating as
intended for both normal and laser spindle modes.

- Elaborated a little more on the new sleep mode in the documentation.


----------------
Date: 2016-10-11
Author: Sonny Jeon
Subject: v1.1c: New sleep mode. Laser mode and other bug fixes.

- New $SLP sleep mode that will disable spindle, coolant, and stepper
enable pins. Allows users to disable their steppers without having to
alter their settings. A reset is required to exit and re-initializes in
alarm state.

- Laser mode wasn’t updating the spindle PWM correctly (effected
spindle speed overrides) and not checking for modal states either.
Fixed both issues.

- While in laser mode, parking motions are ignored, since the power off
delay with the retract motion would burn the material. It will just
turn off and not move. A restore immediately powers up and resumes. No
delays.

- Changing rpm max and min settings did not update the spindle PWM
calculations. Now fixed.

- Increased default planner buffer from 16 to 17 block. It seems to be
stable, but need to monitor this carefully.

- Removed software debounce routine for limit pins. Obsolete.

- Fixed a couple parking motion bugs. One related to restoring
incorrectly and the other the parking rate wasn’t compatible with the
planner structs.

- Fixed a bug caused by refactoring the critical alarms in a recent
push. Soft limits weren’t invoking a critical alarm.

- Updated the documentation with the new sleep feature and added some
more details to the change summary.


----------------
Date: 2016-09-28
Author: Sonny Jeon
Subject: New jog cancel real-time command. Parser typo fix from last push.

- Added a new jog cancel real-time command. Rather than depending on a
feed hold to cancel a jogging motion, this realtime command can be used
instead. The main advantage is if a feed hold is used, you can
accidentally hold the machine right when Grbl returns to IDLE after
completing a jog. And the GUI doesn’t have to worry about tracking this
either.

- Fixed a typo in the g-code parser edits from the last push. Was
causing the G10 set coordinate system command to not work correctly.

- Updated the documentation with the jog cancel command.


----------------
Date: 2016-09-27
Author: Sonny Jeon
Subject: Refactored g-code parser. Saved 60bytes flash and some ram. Edited Readme.

- Freed up another 60 bytes of flash and 12-24 bytes of stack RAM by
using the pre-allocated IJK arc offset vector that is guaranteed to be
not in use. Only G10 and G28/30 require fetching from EEPROM and
retaining extra data. Both commands use axis words, which rules out
G2/3 arcs using IJK offsets existing in same block. Not ideal, but
every byte helps.

- Edited README.


----------------
Date: 2016-09-27
Author: Sonny Jeon
Subject: Update README and clarifications in jogging document.


----------------
Date: 2016-09-26
Author: Sonny Jeon
Subject: v1.1b: Tweaked Bf reports, jogging doc, saved another 160 bytes, minor bug fixes

- Increment to v1.1b due to status report tweak.

- Tweaked the buffer state status reports to show bytes and blocks
available, rather than in use. This does not require knowing the buffer
sizes beforehand. It’s implicit.

- Also, since buffer states are not used by most devs (after
inquiries), it is no longer enabled by default and a status mask option
was added for this.

- Fixed some typos and updated for the report tweak in the
documentation.

- Wrote a joystick implementation concept in the jogging markdown
document. Outlines how to get a low-latency feel to a joystick (and
other input devices).

- Removed XON/XOFF support. It’s not used by anyone because of its
inherent problems. Remains in older versions for reference.

- Added a compile option on how to handle the probe position during a
check mode.

- Fixed a jogging bug. If G93 is the modal state before a jogging
motion, the feed rate did not get calculated correctly. Fixed the issue.

- Refactored some code to save another 160+ bytes. Included an improved
float vector comparison macro and reducing a few large and repetitive
function calls.

- Fixed a probing bug (existing in v0.9 too) where the target positions
were not set correct and error handling was improper.


----------------
Date: 2016-09-25
Author: Sonny Jeon
Subject: Addressed much larger flash size with avr-gcc v4.9.2. Refactored reports to save 160KB.

- The newest Arduino IDE 1.6.12 has recently updated to avr-gcc v4.9.2.
Unfortunately, it produces a compiled size almost 0.7KB to 1KB larger
than prior versions! This can easily cause the base build to exceed the
Arduino Duemilanove/Nano flash limit of 30.5KB. The Arduino Uno seems
to be ok still with its 31.5KB flash limit.

- Makefile `-flto` compile flag added to cut down on the horrible flash
size when using the new avr-gcc. (Edit Makefile and remove comment on
COMPILE definition). This brings it in-line with what the IDE produces.

- Functionalized repetitive tasks in report.c to try to reduce overall
flash size. Successfully cut down about 160bytes.

- Removed printFloat_SettingValue() and printFloat_RPMValue()
functions. These aren’t required and can be replaced with a direct call
to printFloat() because they don’t require a unit conversion check.


----------------
Date: 2016-09-24
Author: Sonny Jeon
Subject: Serial RX count bug fix. Settings codes CSV. More documentation.

- Reverted back the serial RX count function to how it was. The
variable type was unsigned and cause an integer underflow whenever the
calculation produced a negative number. The old way was the correct way.

- Lots of minor edits to the code CSVs and markdown documents.

- Expanded on explaining feedback messages and startup line execution
feedback.

- Created a new settings codes CSV to help GUIs import the values and
meanings.


----------------
Date: 2016-09-22
Author: Sonny Jeon
Subject: Increment to v1.1a, minor compile bug fix, tweaked communication protocol, more docs.

- Incremented to v1.1a, rather than keep 1.0e. This is because there
are existing v1.0 installations. Don’t want to confuse people further.

- Certain version of the Arduino IDE did not like the `inline` in the
function header. Removed from spindle_control files to fix the problem.

- Tweaked the communication protocol slightly. Added message type
indicators for all `[]`bracketed feedback messages. It’s been
problematic for GUI dev to try to determine the context of a message
and how it should be handled. These indictors should help tremendously
to remove context all together.

- Also altered how `$N` startup lines are presented when executed. They
now start with an open chevron ‘>’ followed by the line and an ‘:ok’ to
indicate it executed. The ‘ok’ is on the same line intentionally so it
doesn’t mess up a streaming protocol counter.

- Managed to save a 100+KB from refactoring parts of report.c. (Thanks
Vasilis!) Freed up room to alter the protocol a little.

- Wrote a markdown document on interface messaging to make it clear how
it’s intended to work. See interface.md in /doc/markdown

- Started to pull in some Wiki pages from the old grbl site and
beginning to update them for v1.1.

- Created new commit log for v1.1.


----------------
Date: 2016-09-22
Author: Sonny Jeon
Subject: Merge pull request #1 from winder/dev

Add locale to code CSVs.

----------------
Date: 2016-09-22
Author: winder
Subject: Add locale to code CSVs.


----------------
Date: 2016-09-21
Author: chamnit
Subject: Grbl v1.0e huge beta release. Overrides and new reporting.

- Feature: Realtime feed, rapid, and spindle speed overrides. These
alter the running machine state within tens of milliseconds!
    - Feed override: 100%, +/-10%, +/-1% commands with values 1-200% of
programmed feed
    - Rapid override: 100%, 50%, 25% rapid rate commands
    - Spindle speed override: 100%, +/-10%, +/-1% commands with values
50-200% of programmed speed
    - Override values have configurable limits and increments in
config.h.
- Feature: Realtime toggle overrides for spindle stop, flood coolant,
and optionally mist coolant
    - Spindle stop: Enables and disables spindle during a feed hold.
Automatically restores last spindles state.
    - Flood and mist coolant: Immediately toggles coolant state until
next toggle or g-code coolant command.
- Feature: Jogging mode! Incremental and absolute modes supported.
    - Grbl accepts jogging-specific commands like $J=X100F50. An axis
word and feed rate are required. G20/21 and G90/G91 commands are
accepted.
    - Jog motions can be canceled at any time by a feed hold `!`
command. The buffer is automatically flushed. (No resetting required).
    - Jog motions do not alter the g-code parser state so GUIs don’t
have to track what they changed and correct it.
- Feature: Laser mode setting. Allows Grbl to execute continuous
motions with spindle speed and state changes.
- Feature: Significantly improved status reports. Overhauled to cram in
more meaningful data and still make it smaller on average.
    - All available data is now sent by default, but does not appear if
it doesn’t change or is not active.
    - Machine position(MPos) or work position(WPos) is reported but not
both at the same time. Instead, the work coordinate offsets (WCO)are
sent intermittently whenever it changes or refreshes after 10-30 status
reports. Position vectors are easily computed by WPos  = MPos - WCO.
    - All data has changed in some way. Details of changes are in the
markdown documents and wiki.
- Feature: 16 new realtime commands to control overrides. All in
extended-ASCII character space.
    - While they are not easily typeable and requires a GUI, they can’t
be accidentally triggered by some latent character in the g-code
program and have tons of room for expansion.
- Feature: New substates for HOLD and SAFETY DOOR. A `:x` is appended
to the state, where `x` is an integer and indicates a substate.
    - For example, each integer of a door state describes in what phase
the machine is in during parking. Substates are detailed in the
documentation.
- Feature: With the alarm codes, homing and probe alarms have been
expanded with more codes to provide more exact feedback on what caused
the alarm.
- Feature: New hard limit check upon power-up or reset. If detected, a
feedback message to check the limit switches sent immediately after the
welcome message.
    - May be disabled in config.h.

- OEM feature: Enable/disable `$RST=` individual commands based on
desired behavior in config.h.
- OEM feature: Configurable EEPROM wipe to prevent certain data from
being deleted during firmware upgrade to a new settings version or
`RST=*` command.
- OEM feature: Enable/disable the `$I=` build info write string with
external EEPROM write example sketch.
    - This prevents a user from altering the build info string in
EEPROM. This requires the vendor to write the string to EEPROM via
external means. An Arduino example sketch is provided to accomplish
this. This would be useful for contain product data that is
retrievable.

- Tweak: All feedback has been drastically trimmed to free up flash
space for the v1.0 release.
    - The `$` help message is just one string, listing available
commands.
    - The `$$` settings printout no longer includes descriptions. Only
the setting values. (Sorry it’s this or remove overrides!)
    - Grbl `error:` and `ALARM:` responses now only contain codes. No
descriptions. All codes are explained in documentation.
    - Grbl’s old feedback style may be restored via a config.h, but
keep in mind that it will likely not fit into the Arduino’s flash space.
- Tweak: Grbl now forces a buffer sync or stop motion whenever a g-code
command needs to update and write a value to EEPROM or changes the work
coordinate offset.
    - This addresses two old issues in all prior Grbl versions. First,
an EEPROM write requires interrupts to be disabled, including stepper
and serial comm. Steps can be lost and data can be corrupted. Second,
the work position may not be correlated to the actual machine position,
since machine position is derived from the actual current execution
state, while work position is based on the g-code parser offset state.
They are usually not in sync and the parser state is several motions
behind. This forced sync ensures work and machine positions are always
correct.
    - This behavior can be disabled through a config.h option, but it’s
not recommended to do so.
- Tweak: To make status reports standardized, users can no longer
change what is reported via status report mask, except for only
toggling machine or work positions.
    - All other data fields are included in the report and can only be
disabled through the config.h file. It’s not recommended to alter this,
because GUIs will be expecting this data to be present and may not be
compatible.
- Tweak: Homing cycle and parking motion no longer report a negative
line number in a status report. These will now not report a line number
at all.
- Tweak: New `[Restoring spindle]` message when restoring from a
spindle stop override. Provides feedback what Grbl is doing while the
spindle is powering up and a 4.0 second delay is enforced.
- Tweak: Override values are reset to 100% upon M2/30. This behavior
can be disabled in config.h
- Tweak: The planner buffer size has been reduced from 18 to 16 to free
up RAM for tracking and controlling overrides.
- Tweak: TX buffer size has been increased from 64 to 90 bytes to
improve status reporting and overall performance.
- Tweak: Removed the MOTION CANCEL state. It was redundant and didn’t
affect Grbl’s overall operation by doing so.
- Tweak: Grbl’s serial buffer increased by +1 internally, such that 128
bytes means 128, not 127 due to the ring buffer implementation. Long
overdue.
- Tweak: Altered sys.alarm variable to be set by alarm codes, rather
than bit flags. Simplified how it worked overall.
- Tweak: Planner buffer and serial RX buffer usage has been combined in
the status reports.
- Tweak: Pin state reporting has been refactored to report only the
pins “triggered” and nothing when not “triggered”.
- Tweak: Current machine rate or speed is now included in every report.
- Tweak: The work coordinate offset (WCO) and override states only need
to be refreshed intermittently or reported when they change. The
refresh rates may be altered for each in the config.h file with
different idle and busy rates to lessen Grbl’s load during a job.
- Tweak: For temporary compatibility to existing GUIs until they are
updated, an option to revert back to the old style status reports is
available in config.h, but not recommended for long term use.
- Tweak: Removed old limit pin state reporting option from config.h in
lieu of new status report that includes them.
- Tweak: Updated the defaults.h file to include laser mode, altered
status report mask, and fix an issue with a missing invert probe pin
default.

- Refactor: Changed how planner line data is generated and passed to
the planner and onto the step generator. By making it a struct
variable, this saved significant flash space.
- Refactor: Major re-factoring of the planner to incorporate override
values and allow for re-calculations fast enough to immediately take
effect during operation. No small feat.
- Refactor: Re-factored the step segment generator for re-computing new
override states.
- Refactor: Re-factored spindle_control.c to accommodate the spindle
speed overrides and laser mode.
- Refactor: Re-factored parts of the codebase for a new jogging mode.
Still under development though and slated to be part of the official
v1.0 release. Hang tight.
- Refactor: Created functions for computing a unit vector and value
limiting based on axis maximums to free up more flash.
- Refactor: The spindle PWM is now set directly inside of the stepper
ISR as it loads new step segments.
- Refactor: Moved machine travel checks out of soft limits function
into its own since jogging uses this too.
- Refactor: Removed coolant_stop() and combined with
coolant_set_state().
- Refactor: The serial RX ISR forks off extended ASCII values to
quickly assess the new override realtime commands.
- Refactor: Altered some names of the step control flags.
- Refactor: Improved efficiency of the serial RX get buffer count
function.
- Refactor: Saved significant flash by removing and combining print
functions. Namely the uint8 base10 and base2 functions.
- Refactor: Moved the probe state check in the main stepper ISR to
improve its efficiency.
- Refactor: Single character printPgmStrings() went converted to direct
serial_write() commands to save significant flash space.

- Documentation: Detailed Markdown documents on error codes, alarm
codes, messages, new real-time commands, new status reports, and how
jogging works. More to come later and will be posted on the Wiki as
well.
- Documentation: CSV files for quick importing of Grbl error and alarm
codes.

- Bug Fix: Applied v0.9 master fixes to CoreXY homing.
- Bug Fix: The print float function would cause Grbl to crash if a
value was 1e6 or greater. Increased the buffer by 3 bytes to help
prevent this in the future.
- Bug Fix: Build info and startup string EEPROM restoring was not
writing the checksum value.
- Bug Fix: Corrected an issue with safety door restoring the proper
spindle and coolant state. It worked before, but breaks with laser mode
that can continually change spindle state per planner block.
- Bug Fix: Move system position and probe position arrays out of the
system_t struct. Ran into some compiling errors that were hard to track
down as to why. Moving them out fixed it.