b753c542c7
- Increment to v1.1e due to new laser features. - After several discussions with some prominent laser people, a few tweaks to the new laser mode has been installed. - LASER: M3 behaves in a constant power mode. - LASER: M4 behaves in a dynamic power mode, where the laser power is automatically adjusted based on how fast Grbl is moving relative to the programmed feed rate. This is the same as the CONSTANT_POWER_PER_RATE config.h option in the last version. NOTE: When not in motion in M4, Grbl automatically turns off the laser. Again, it only operates while moving! - LASER: Only G1, G2, and G3 motion modes will turn on the laser. So, this means that G0, G80 motion modes will always keep the laser disabled. No matter if M3/M4 are active! - LASER: A spindle stop override is automatically invoked when a laser is put in a feed hold. This behavior may be disabled by a config.h option. - Lots of little tweaks to the g-code parser to help streamline it a bit. It should no effect how it operates. Generally just added a parser flag to track and execute certain scenarios a little more clearly. - Jog motions now allow line numbers to be passed to it and will be displayed in the status reports. - Fixed a CoreXY homing bug. - Fixed an issue when $13 is changed, WCO isn’t sent immediately. - Altered how spindle PWM is set in the stepper ISR. Updated on a step segment basis now. May need to change this back if there are any oddities from doing this. - Updated some documentation. Clarified why M0 no longer showing up in $G and why a `1.` floating point values are shown with no decimals, like so `1`.
1014 lines
51 KiB
C
1014 lines
51 KiB
C
/*
|
|
stepper.c - stepper motor driver: executes motion plans using stepper motors
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2011-2016 Sungeun K. Jeon for Gnea Research LLC
|
|
Copyright (c) 2009-2011 Simen Svale Skogsrud
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include "grbl.h"
|
|
|
|
|
|
// Some useful constants.
|
|
#define DT_SEGMENT (1.0/(ACCELERATION_TICKS_PER_SECOND*60.0)) // min/segment
|
|
#define REQ_MM_INCREMENT_SCALAR 1.25
|
|
#define RAMP_ACCEL 0
|
|
#define RAMP_CRUISE 1
|
|
#define RAMP_DECEL 2
|
|
#define RAMP_DECEL_OVERRIDE 3
|
|
|
|
#define PREP_FLAG_RECALCULATE bit(0)
|
|
#define PREP_FLAG_HOLD_PARTIAL_BLOCK bit(1)
|
|
#define PREP_FLAG_PARKING bit(2)
|
|
#define PREP_FLAG_DECEL_OVERRIDE bit(3)
|
|
|
|
// Define Adaptive Multi-Axis Step-Smoothing(AMASS) levels and cutoff frequencies. The highest level
|
|
// frequency bin starts at 0Hz and ends at its cutoff frequency. The next lower level frequency bin
|
|
// starts at the next higher cutoff frequency, and so on. The cutoff frequencies for each level must
|
|
// be considered carefully against how much it over-drives the stepper ISR, the accuracy of the 16-bit
|
|
// timer, and the CPU overhead. Level 0 (no AMASS, normal operation) frequency bin starts at the
|
|
// Level 1 cutoff frequency and up to as fast as the CPU allows (over 30kHz in limited testing).
|
|
// NOTE: AMASS cutoff frequency multiplied by ISR overdrive factor must not exceed maximum step frequency.
|
|
// NOTE: Current settings are set to overdrive the ISR to no more than 16kHz, balancing CPU overhead
|
|
// and timer accuracy. Do not alter these settings unless you know what you are doing.
|
|
#define MAX_AMASS_LEVEL 3
|
|
// AMASS_LEVEL0: Normal operation. No AMASS. No upper cutoff frequency. Starts at LEVEL1 cutoff frequency.
|
|
#define AMASS_LEVEL1 (F_CPU/8000) // Over-drives ISR (x2). Defined as F_CPU/(Cutoff frequency in Hz)
|
|
#define AMASS_LEVEL2 (F_CPU/4000) // Over-drives ISR (x4)
|
|
#define AMASS_LEVEL3 (F_CPU/2000) // Over-drives ISR (x8)
|
|
|
|
|
|
// Stores the planner block Bresenham algorithm execution data for the segments in the segment
|
|
// buffer. Normally, this buffer is partially in-use, but, for the worst case scenario, it will
|
|
// never exceed the number of accessible stepper buffer segments (SEGMENT_BUFFER_SIZE-1).
|
|
// NOTE: This data is copied from the prepped planner blocks so that the planner blocks may be
|
|
// discarded when entirely consumed and completed by the segment buffer. Also, AMASS alters this
|
|
// data for its own use.
|
|
typedef struct {
|
|
uint32_t steps[N_AXIS];
|
|
uint32_t step_event_count;
|
|
uint8_t direction_bits;
|
|
#ifdef VARIABLE_SPINDLE
|
|
uint8_t is_pwm_rate_adjusted; // Tracks motions that require constant laser power/rate
|
|
#endif
|
|
} st_block_t;
|
|
static st_block_t st_block_buffer[SEGMENT_BUFFER_SIZE-1];
|
|
|
|
// Primary stepper segment ring buffer. Contains small, short line segments for the stepper
|
|
// algorithm to execute, which are "checked-out" incrementally from the first block in the
|
|
// planner buffer. Once "checked-out", the steps in the segments buffer cannot be modified by
|
|
// the planner, where the remaining planner block steps still can.
|
|
typedef struct {
|
|
uint16_t n_step; // Number of step events to be executed for this segment
|
|
uint16_t cycles_per_tick; // Step distance traveled per ISR tick, aka step rate.
|
|
uint8_t st_block_index; // Stepper block data index. Uses this information to execute this segment.
|
|
#ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
|
|
uint8_t amass_level; // Indicates AMASS level for the ISR to execute this segment
|
|
#else
|
|
uint8_t prescaler; // Without AMASS, a prescaler is required to adjust for slow timing.
|
|
#endif
|
|
#ifdef VARIABLE_SPINDLE
|
|
uint8_t spindle_pwm;
|
|
#endif
|
|
} segment_t;
|
|
static segment_t segment_buffer[SEGMENT_BUFFER_SIZE];
|
|
|
|
// Stepper ISR data struct. Contains the running data for the main stepper ISR.
|
|
typedef struct {
|
|
// Used by the bresenham line algorithm
|
|
uint32_t counter_x, // Counter variables for the bresenham line tracer
|
|
counter_y,
|
|
counter_z;
|
|
#ifdef STEP_PULSE_DELAY
|
|
uint8_t step_bits; // Stores out_bits output to complete the step pulse delay
|
|
#endif
|
|
|
|
uint8_t execute_step; // Flags step execution for each interrupt.
|
|
uint8_t step_pulse_time; // Step pulse reset time after step rise
|
|
uint8_t step_outbits; // The next stepping-bits to be output
|
|
uint8_t dir_outbits;
|
|
#ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
|
|
uint32_t steps[N_AXIS];
|
|
#endif
|
|
|
|
uint16_t step_count; // Steps remaining in line segment motion
|
|
uint8_t exec_block_index; // Tracks the current st_block index. Change indicates new block.
|
|
st_block_t *exec_block; // Pointer to the block data for the segment being executed
|
|
segment_t *exec_segment; // Pointer to the segment being executed
|
|
} stepper_t;
|
|
static stepper_t st;
|
|
|
|
// Step segment ring buffer indices
|
|
static volatile uint8_t segment_buffer_tail;
|
|
static uint8_t segment_buffer_head;
|
|
static uint8_t segment_next_head;
|
|
|
|
// Step and direction port invert masks.
|
|
static uint8_t step_port_invert_mask;
|
|
static uint8_t dir_port_invert_mask;
|
|
|
|
// Used to avoid ISR nesting of the "Stepper Driver Interrupt". Should never occur though.
|
|
static volatile uint8_t busy;
|
|
|
|
// Pointers for the step segment being prepped from the planner buffer. Accessed only by the
|
|
// main program. Pointers may be planning segments or planner blocks ahead of what being executed.
|
|
static plan_block_t *pl_block; // Pointer to the planner block being prepped
|
|
static st_block_t *st_prep_block; // Pointer to the stepper block data being prepped
|
|
|
|
// Segment preparation data struct. Contains all the necessary information to compute new segments
|
|
// based on the current executing planner block.
|
|
typedef struct {
|
|
uint8_t st_block_index; // Index of stepper common data block being prepped
|
|
uint8_t recalculate_flag;
|
|
|
|
float dt_remainder;
|
|
float steps_remaining;
|
|
float step_per_mm;
|
|
float req_mm_increment;
|
|
|
|
#ifdef PARKING_ENABLE
|
|
uint8_t last_st_block_index;
|
|
float last_steps_remaining;
|
|
float last_step_per_mm;
|
|
float last_dt_remainder;
|
|
#endif
|
|
|
|
uint8_t ramp_type; // Current segment ramp state
|
|
float mm_complete; // End of velocity profile from end of current planner block in (mm).
|
|
// NOTE: This value must coincide with a step(no mantissa) when converted.
|
|
float current_speed; // Current speed at the end of the segment buffer (mm/min)
|
|
float maximum_speed; // Maximum speed of executing block. Not always nominal speed. (mm/min)
|
|
float exit_speed; // Exit speed of executing block (mm/min)
|
|
float accelerate_until; // Acceleration ramp end measured from end of block (mm)
|
|
float decelerate_after; // Deceleration ramp start measured from end of block (mm)
|
|
|
|
#ifdef VARIABLE_SPINDLE
|
|
float inv_rate; // Used by PWM laser mode to speed up segment calculations.
|
|
uint8_t current_spindle_pwm;
|
|
#endif
|
|
} st_prep_t;
|
|
static st_prep_t prep;
|
|
|
|
|
|
/* BLOCK VELOCITY PROFILE DEFINITION
|
|
__________________________
|
|
/| |\ _________________ ^
|
|
/ | | \ /| |\ |
|
|
/ | | \ / | | \ s
|
|
/ | | | | | \ p
|
|
/ | | | | | \ e
|
|
+-----+------------------------+---+--+---------------+----+ e
|
|
| BLOCK 1 ^ BLOCK 2 | d
|
|
|
|
|
time -----> EXAMPLE: Block 2 entry speed is at max junction velocity
|
|
|
|
The planner block buffer is planned assuming constant acceleration velocity profiles and are
|
|
continuously joined at block junctions as shown above. However, the planner only actively computes
|
|
the block entry speeds for an optimal velocity plan, but does not compute the block internal
|
|
velocity profiles. These velocity profiles are computed ad-hoc as they are executed by the
|
|
stepper algorithm and consists of only 7 possible types of profiles: cruise-only, cruise-
|
|
deceleration, acceleration-cruise, acceleration-only, deceleration-only, full-trapezoid, and
|
|
triangle(no cruise).
|
|
|
|
maximum_speed (< nominal_speed) -> +
|
|
+--------+ <- maximum_speed (= nominal_speed) /|\
|
|
/ \ / | \
|
|
current_speed -> + \ / | + <- exit_speed
|
|
| + <- exit_speed / | |
|
|
+-------------+ current_speed -> +----+--+
|
|
time --> ^ ^ ^ ^
|
|
| | | |
|
|
decelerate_after(in mm) decelerate_after(in mm)
|
|
^ ^ ^ ^
|
|
| | | |
|
|
accelerate_until(in mm) accelerate_until(in mm)
|
|
|
|
The step segment buffer computes the executing block velocity profile and tracks the critical
|
|
parameters for the stepper algorithm to accurately trace the profile. These critical parameters
|
|
are shown and defined in the above illustration.
|
|
*/
|
|
|
|
|
|
// Stepper state initialization. Cycle should only start if the st.cycle_start flag is
|
|
// enabled. Startup init and limits call this function but shouldn't start the cycle.
|
|
void st_wake_up()
|
|
{
|
|
// Enable stepper drivers.
|
|
if (bit_istrue(settings.flags,BITFLAG_INVERT_ST_ENABLE)) { STEPPERS_DISABLE_PORT |= (1<<STEPPERS_DISABLE_BIT); }
|
|
else { STEPPERS_DISABLE_PORT &= ~(1<<STEPPERS_DISABLE_BIT); }
|
|
|
|
// Initialize stepper output bits to ensure first ISR call does not step.
|
|
st.step_outbits = step_port_invert_mask;
|
|
|
|
// Initialize step pulse timing from settings. Here to ensure updating after re-writing.
|
|
#ifdef STEP_PULSE_DELAY
|
|
// Set total step pulse time after direction pin set. Ad hoc computation from oscilloscope.
|
|
st.step_pulse_time = -(((settings.pulse_microseconds+STEP_PULSE_DELAY-2)*TICKS_PER_MICROSECOND) >> 3);
|
|
// Set delay between direction pin write and step command.
|
|
OCR0A = -(((settings.pulse_microseconds)*TICKS_PER_MICROSECOND) >> 3);
|
|
#else // Normal operation
|
|
// Set step pulse time. Ad hoc computation from oscilloscope. Uses two's complement.
|
|
st.step_pulse_time = -(((settings.pulse_microseconds-2)*TICKS_PER_MICROSECOND) >> 3);
|
|
#endif
|
|
|
|
// Enable Stepper Driver Interrupt
|
|
TIMSK1 |= (1<<OCIE1A);
|
|
}
|
|
|
|
|
|
// Stepper shutdown
|
|
void st_go_idle()
|
|
{
|
|
// Disable Stepper Driver Interrupt. Allow Stepper Port Reset Interrupt to finish, if active.
|
|
TIMSK1 &= ~(1<<OCIE1A); // Disable Timer1 interrupt
|
|
TCCR1B = (TCCR1B & ~((1<<CS12) | (1<<CS11))) | (1<<CS10); // Reset clock to no prescaling.
|
|
busy = false;
|
|
|
|
// Set stepper driver idle state, disabled or enabled, depending on settings and circumstances.
|
|
bool pin_state = false; // Keep enabled.
|
|
if (((settings.stepper_idle_lock_time != 0xff) || sys_rt_exec_alarm || sys.state == STATE_SLEEP) && sys.state != STATE_HOMING) {
|
|
// Force stepper dwell to lock axes for a defined amount of time to ensure the axes come to a complete
|
|
// stop and not drift from residual inertial forces at the end of the last movement.
|
|
delay_ms(settings.stepper_idle_lock_time);
|
|
pin_state = true; // Override. Disable steppers.
|
|
}
|
|
if (bit_istrue(settings.flags,BITFLAG_INVERT_ST_ENABLE)) { pin_state = !pin_state; } // Apply pin invert.
|
|
if (pin_state) { STEPPERS_DISABLE_PORT |= (1<<STEPPERS_DISABLE_BIT); }
|
|
else { STEPPERS_DISABLE_PORT &= ~(1<<STEPPERS_DISABLE_BIT); }
|
|
}
|
|
|
|
|
|
/* "The Stepper Driver Interrupt" - This timer interrupt is the workhorse of Grbl. Grbl employs
|
|
the venerable Bresenham line algorithm to manage and exactly synchronize multi-axis moves.
|
|
Unlike the popular DDA algorithm, the Bresenham algorithm is not susceptible to numerical
|
|
round-off errors and only requires fast integer counters, meaning low computational overhead
|
|
and maximizing the Arduino's capabilities. However, the downside of the Bresenham algorithm
|
|
is, for certain multi-axis motions, the non-dominant axes may suffer from un-smooth step
|
|
pulse trains, or aliasing, which can lead to strange audible noises or shaking. This is
|
|
particularly noticeable or may cause motion issues at low step frequencies (0-5kHz), but
|
|
is usually not a physical problem at higher frequencies, although audible.
|
|
To improve Bresenham multi-axis performance, Grbl uses what we call an Adaptive Multi-Axis
|
|
Step Smoothing (AMASS) algorithm, which does what the name implies. At lower step frequencies,
|
|
AMASS artificially increases the Bresenham resolution without effecting the algorithm's
|
|
innate exactness. AMASS adapts its resolution levels automatically depending on the step
|
|
frequency to be executed, meaning that for even lower step frequencies the step smoothing
|
|
level increases. Algorithmically, AMASS is acheived by a simple bit-shifting of the Bresenham
|
|
step count for each AMASS level. For example, for a Level 1 step smoothing, we bit shift
|
|
the Bresenham step event count, effectively multiplying it by 2, while the axis step counts
|
|
remain the same, and then double the stepper ISR frequency. In effect, we are allowing the
|
|
non-dominant Bresenham axes step in the intermediate ISR tick, while the dominant axis is
|
|
stepping every two ISR ticks, rather than every ISR tick in the traditional sense. At AMASS
|
|
Level 2, we simply bit-shift again, so the non-dominant Bresenham axes can step within any
|
|
of the four ISR ticks, the dominant axis steps every four ISR ticks, and quadruple the
|
|
stepper ISR frequency. And so on. This, in effect, virtually eliminates multi-axis aliasing
|
|
issues with the Bresenham algorithm and does not significantly alter Grbl's performance, but
|
|
in fact, more efficiently utilizes unused CPU cycles overall throughout all configurations.
|
|
AMASS retains the Bresenham algorithm exactness by requiring that it always executes a full
|
|
Bresenham step, regardless of AMASS Level. Meaning that for an AMASS Level 2, all four
|
|
intermediate steps must be completed such that baseline Bresenham (Level 0) count is always
|
|
retained. Similarly, AMASS Level 3 means all eight intermediate steps must be executed.
|
|
Although the AMASS Levels are in reality arbitrary, where the baseline Bresenham counts can
|
|
be multiplied by any integer value, multiplication by powers of two are simply used to ease
|
|
CPU overhead with bitshift integer operations.
|
|
This interrupt is simple and dumb by design. All the computational heavy-lifting, as in
|
|
determining accelerations, is performed elsewhere. This interrupt pops pre-computed segments,
|
|
defined as constant velocity over n number of steps, from the step segment buffer and then
|
|
executes them by pulsing the stepper pins appropriately via the Bresenham algorithm. This
|
|
ISR is supported by The Stepper Port Reset Interrupt which it uses to reset the stepper port
|
|
after each pulse. The bresenham line tracer algorithm controls all stepper outputs
|
|
simultaneously with these two interrupts.
|
|
|
|
NOTE: This interrupt must be as efficient as possible and complete before the next ISR tick,
|
|
which for Grbl must be less than 33.3usec (@30kHz ISR rate). Oscilloscope measured time in
|
|
ISR is 5usec typical and 25usec maximum, well below requirement.
|
|
NOTE: This ISR expects at least one step to be executed per segment.
|
|
*/
|
|
// TODO: Replace direct updating of the int32 position counters in the ISR somehow. Perhaps use smaller
|
|
// int8 variables and update position counters only when a segment completes. This can get complicated
|
|
// with probing and homing cycles that require true real-time positions.
|
|
ISR(TIMER1_COMPA_vect)
|
|
{
|
|
if (busy) { return; } // The busy-flag is used to avoid reentering this interrupt
|
|
|
|
// Set the direction pins a couple of nanoseconds before we step the steppers
|
|
DIRECTION_PORT = (DIRECTION_PORT & ~DIRECTION_MASK) | (st.dir_outbits & DIRECTION_MASK);
|
|
|
|
// Then pulse the stepping pins
|
|
#ifdef STEP_PULSE_DELAY
|
|
st.step_bits = (STEP_PORT & ~STEP_MASK) | st.step_outbits; // Store out_bits to prevent overwriting.
|
|
#else // Normal operation
|
|
STEP_PORT = (STEP_PORT & ~STEP_MASK) | st.step_outbits;
|
|
#endif
|
|
|
|
// Enable step pulse reset timer so that The Stepper Port Reset Interrupt can reset the signal after
|
|
// exactly settings.pulse_microseconds microseconds, independent of the main Timer1 prescaler.
|
|
TCNT0 = st.step_pulse_time; // Reload Timer0 counter
|
|
TCCR0B = (1<<CS01); // Begin Timer0. Full speed, 1/8 prescaler
|
|
|
|
busy = true;
|
|
sei(); // Re-enable interrupts to allow Stepper Port Reset Interrupt to fire on-time.
|
|
// NOTE: The remaining code in this ISR will finish before returning to main program.
|
|
|
|
// If there is no step segment, attempt to pop one from the stepper buffer
|
|
if (st.exec_segment == NULL) {
|
|
// Anything in the buffer? If so, load and initialize next step segment.
|
|
if (segment_buffer_head != segment_buffer_tail) {
|
|
// Initialize new step segment and load number of steps to execute
|
|
st.exec_segment = &segment_buffer[segment_buffer_tail];
|
|
|
|
#ifndef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
|
|
// With AMASS is disabled, set timer prescaler for segments with slow step frequencies (< 250Hz).
|
|
TCCR1B = (TCCR1B & ~(0x07<<CS10)) | (st.exec_segment->prescaler<<CS10);
|
|
#endif
|
|
|
|
// Initialize step segment timing per step and load number of steps to execute.
|
|
OCR1A = st.exec_segment->cycles_per_tick;
|
|
st.step_count = st.exec_segment->n_step; // NOTE: Can sometimes be zero when moving slow.
|
|
// If the new segment starts a new planner block, initialize stepper variables and counters.
|
|
// NOTE: When the segment data index changes, this indicates a new planner block.
|
|
if ( st.exec_block_index != st.exec_segment->st_block_index ) {
|
|
st.exec_block_index = st.exec_segment->st_block_index;
|
|
st.exec_block = &st_block_buffer[st.exec_block_index];
|
|
|
|
// Initialize Bresenham line and distance counters
|
|
st.counter_x = st.counter_y = st.counter_z = (st.exec_block->step_event_count >> 1);
|
|
}
|
|
st.dir_outbits = st.exec_block->direction_bits ^ dir_port_invert_mask;
|
|
|
|
#ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
|
|
// With AMASS enabled, adjust Bresenham axis increment counters according to AMASS level.
|
|
st.steps[X_AXIS] = st.exec_block->steps[X_AXIS] >> st.exec_segment->amass_level;
|
|
st.steps[Y_AXIS] = st.exec_block->steps[Y_AXIS] >> st.exec_segment->amass_level;
|
|
st.steps[Z_AXIS] = st.exec_block->steps[Z_AXIS] >> st.exec_segment->amass_level;
|
|
#endif
|
|
|
|
#ifdef VARIABLE_SPINDLE
|
|
// Set real-time spindle output as segment is loaded, just prior to the first step.
|
|
spindle_set_speed(st.exec_segment->spindle_pwm);
|
|
#endif
|
|
|
|
} else {
|
|
// Segment buffer empty. Shutdown.
|
|
st_go_idle();
|
|
// Ensure pwm is set properly upon completion of rate-controlled motion.
|
|
if (st.exec_block->is_pwm_rate_adjusted) { spindle_set_speed(SPINDLE_PWM_OFF_VALUE); }
|
|
system_set_exec_state_flag(EXEC_CYCLE_STOP); // Flag main program for cycle end
|
|
return; // Nothing to do but exit.
|
|
}
|
|
}
|
|
|
|
|
|
// Check probing state.
|
|
if (sys_probe_state == PROBE_ACTIVE) { probe_state_monitor(); }
|
|
|
|
// Reset step out bits.
|
|
st.step_outbits = 0;
|
|
|
|
// Execute step displacement profile by Bresenham line algorithm
|
|
#ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
|
|
st.counter_x += st.steps[X_AXIS];
|
|
#else
|
|
st.counter_x += st.exec_block->steps[X_AXIS];
|
|
#endif
|
|
if (st.counter_x > st.exec_block->step_event_count) {
|
|
st.step_outbits |= (1<<X_STEP_BIT);
|
|
st.counter_x -= st.exec_block->step_event_count;
|
|
if (st.exec_block->direction_bits & (1<<X_DIRECTION_BIT)) { sys_position[X_AXIS]--; }
|
|
else { sys_position[X_AXIS]++; }
|
|
}
|
|
#ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
|
|
st.counter_y += st.steps[Y_AXIS];
|
|
#else
|
|
st.counter_y += st.exec_block->steps[Y_AXIS];
|
|
#endif
|
|
if (st.counter_y > st.exec_block->step_event_count) {
|
|
st.step_outbits |= (1<<Y_STEP_BIT);
|
|
st.counter_y -= st.exec_block->step_event_count;
|
|
if (st.exec_block->direction_bits & (1<<Y_DIRECTION_BIT)) { sys_position[Y_AXIS]--; }
|
|
else { sys_position[Y_AXIS]++; }
|
|
}
|
|
#ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
|
|
st.counter_z += st.steps[Z_AXIS];
|
|
#else
|
|
st.counter_z += st.exec_block->steps[Z_AXIS];
|
|
#endif
|
|
if (st.counter_z > st.exec_block->step_event_count) {
|
|
st.step_outbits |= (1<<Z_STEP_BIT);
|
|
st.counter_z -= st.exec_block->step_event_count;
|
|
if (st.exec_block->direction_bits & (1<<Z_DIRECTION_BIT)) { sys_position[Z_AXIS]--; }
|
|
else { sys_position[Z_AXIS]++; }
|
|
}
|
|
|
|
// During a homing cycle, lock out and prevent desired axes from moving.
|
|
if (sys.state == STATE_HOMING) { st.step_outbits &= sys.homing_axis_lock; }
|
|
|
|
st.step_count--; // Decrement step events count
|
|
if (st.step_count == 0) {
|
|
// Segment is complete. Discard current segment and advance segment indexing.
|
|
st.exec_segment = NULL;
|
|
if ( ++segment_buffer_tail == SEGMENT_BUFFER_SIZE) { segment_buffer_tail = 0; }
|
|
}
|
|
|
|
st.step_outbits ^= step_port_invert_mask; // Apply step port invert mask
|
|
busy = false;
|
|
}
|
|
|
|
|
|
/* The Stepper Port Reset Interrupt: Timer0 OVF interrupt handles the falling edge of the step
|
|
pulse. This should always trigger before the next Timer1 COMPA interrupt and independently
|
|
finish, if Timer1 is disabled after completing a move.
|
|
NOTE: Interrupt collisions between the serial and stepper interrupts can cause delays by
|
|
a few microseconds, if they execute right before one another. Not a big deal, but can
|
|
cause issues at high step rates if another high frequency asynchronous interrupt is
|
|
added to Grbl.
|
|
*/
|
|
// This interrupt is enabled by ISR_TIMER1_COMPAREA when it sets the motor port bits to execute
|
|
// a step. This ISR resets the motor port after a short period (settings.pulse_microseconds)
|
|
// completing one step cycle.
|
|
ISR(TIMER0_OVF_vect)
|
|
{
|
|
// Reset stepping pins (leave the direction pins)
|
|
STEP_PORT = (STEP_PORT & ~STEP_MASK) | (step_port_invert_mask & STEP_MASK);
|
|
TCCR0B = 0; // Disable Timer0 to prevent re-entering this interrupt when it's not needed.
|
|
}
|
|
#ifdef STEP_PULSE_DELAY
|
|
// This interrupt is used only when STEP_PULSE_DELAY is enabled. Here, the step pulse is
|
|
// initiated after the STEP_PULSE_DELAY time period has elapsed. The ISR TIMER2_OVF interrupt
|
|
// will then trigger after the appropriate settings.pulse_microseconds, as in normal operation.
|
|
// The new timing between direction, step pulse, and step complete events are setup in the
|
|
// st_wake_up() routine.
|
|
ISR(TIMER0_COMPA_vect)
|
|
{
|
|
STEP_PORT = st.step_bits; // Begin step pulse.
|
|
}
|
|
#endif
|
|
|
|
|
|
// Generates the step and direction port invert masks used in the Stepper Interrupt Driver.
|
|
void st_generate_step_dir_invert_masks()
|
|
{
|
|
uint8_t idx;
|
|
step_port_invert_mask = 0;
|
|
dir_port_invert_mask = 0;
|
|
for (idx=0; idx<N_AXIS; idx++) {
|
|
if (bit_istrue(settings.step_invert_mask,bit(idx))) { step_port_invert_mask |= get_step_pin_mask(idx); }
|
|
if (bit_istrue(settings.dir_invert_mask,bit(idx))) { dir_port_invert_mask |= get_direction_pin_mask(idx); }
|
|
}
|
|
}
|
|
|
|
|
|
// Reset and clear stepper subsystem variables
|
|
void st_reset()
|
|
{
|
|
// Initialize stepper driver idle state.
|
|
st_go_idle();
|
|
|
|
// Initialize stepper algorithm variables.
|
|
memset(&prep, 0, sizeof(st_prep_t));
|
|
memset(&st, 0, sizeof(stepper_t));
|
|
st.exec_segment = NULL;
|
|
pl_block = NULL; // Planner block pointer used by segment buffer
|
|
segment_buffer_tail = 0;
|
|
segment_buffer_head = 0; // empty = tail
|
|
segment_next_head = 1;
|
|
busy = false;
|
|
|
|
st_generate_step_dir_invert_masks();
|
|
st.dir_outbits = dir_port_invert_mask; // Initialize direction bits to default.
|
|
|
|
// Initialize step and direction port pins.
|
|
STEP_PORT = (STEP_PORT & ~STEP_MASK) | step_port_invert_mask;
|
|
DIRECTION_PORT = (DIRECTION_PORT & ~DIRECTION_MASK) | dir_port_invert_mask;
|
|
}
|
|
|
|
|
|
// Initialize and start the stepper motor subsystem
|
|
void stepper_init()
|
|
{
|
|
// Configure step and direction interface pins
|
|
STEP_DDR |= STEP_MASK;
|
|
STEPPERS_DISABLE_DDR |= 1<<STEPPERS_DISABLE_BIT;
|
|
DIRECTION_DDR |= DIRECTION_MASK;
|
|
|
|
// Configure Timer 1: Stepper Driver Interrupt
|
|
TCCR1B &= ~(1<<WGM13); // waveform generation = 0100 = CTC
|
|
TCCR1B |= (1<<WGM12);
|
|
TCCR1A &= ~((1<<WGM11) | (1<<WGM10));
|
|
TCCR1A &= ~((1<<COM1A1) | (1<<COM1A0) | (1<<COM1B1) | (1<<COM1B0)); // Disconnect OC1 output
|
|
// TCCR1B = (TCCR1B & ~((1<<CS12) | (1<<CS11))) | (1<<CS10); // Set in st_go_idle().
|
|
// TIMSK1 &= ~(1<<OCIE1A); // Set in st_go_idle().
|
|
|
|
// Configure Timer 0: Stepper Port Reset Interrupt
|
|
TIMSK0 &= ~((1<<OCIE0B) | (1<<OCIE0A) | (1<<TOIE0)); // Disconnect OC0 outputs and OVF interrupt.
|
|
TCCR0A = 0; // Normal operation
|
|
TCCR0B = 0; // Disable Timer0 until needed
|
|
TIMSK0 |= (1<<TOIE0); // Enable Timer0 overflow interrupt
|
|
#ifdef STEP_PULSE_DELAY
|
|
TIMSK0 |= (1<<OCIE0A); // Enable Timer0 Compare Match A interrupt
|
|
#endif
|
|
}
|
|
|
|
|
|
// Called by planner_recalculate() when the executing block is updated by the new plan.
|
|
void st_update_plan_block_parameters()
|
|
{
|
|
if (pl_block != NULL) { // Ignore if at start of a new block.
|
|
prep.recalculate_flag |= PREP_FLAG_RECALCULATE;
|
|
pl_block->entry_speed_sqr = prep.current_speed*prep.current_speed; // Update entry speed.
|
|
pl_block = NULL; // Flag st_prep_segment() to load and check active velocity profile.
|
|
}
|
|
}
|
|
|
|
|
|
// Increments the step segment buffer block data ring buffer.
|
|
static uint8_t st_next_block_index(uint8_t block_index)
|
|
{
|
|
block_index++;
|
|
if ( block_index == (SEGMENT_BUFFER_SIZE-1) ) { return(0); }
|
|
return(block_index);
|
|
}
|
|
|
|
|
|
#ifdef PARKING_ENABLE
|
|
// Changes the run state of the step segment buffer to execute the special parking motion.
|
|
void st_parking_setup_buffer()
|
|
{
|
|
// Store step execution data of partially completed block, if necessary.
|
|
if (prep.recalculate_flag & PREP_FLAG_HOLD_PARTIAL_BLOCK) {
|
|
prep.last_st_block_index = prep.st_block_index;
|
|
prep.last_steps_remaining = prep.steps_remaining;
|
|
prep.last_dt_remainder = prep.dt_remainder;
|
|
prep.last_step_per_mm = prep.step_per_mm;
|
|
}
|
|
// Set flags to execute a parking motion
|
|
prep.recalculate_flag |= PREP_FLAG_PARKING;
|
|
prep.recalculate_flag &= ~(PREP_FLAG_RECALCULATE);
|
|
pl_block = NULL; // Always reset parking motion to reload new block.
|
|
}
|
|
|
|
|
|
// Restores the step segment buffer to the normal run state after a parking motion.
|
|
void st_parking_restore_buffer()
|
|
{
|
|
// Restore step execution data and flags of partially completed block, if necessary.
|
|
if (prep.recalculate_flag & PREP_FLAG_HOLD_PARTIAL_BLOCK) {
|
|
st_prep_block = &st_block_buffer[prep.last_st_block_index];
|
|
prep.st_block_index = prep.last_st_block_index;
|
|
prep.steps_remaining = prep.last_steps_remaining;
|
|
prep.dt_remainder = prep.last_dt_remainder;
|
|
prep.step_per_mm = prep.last_step_per_mm;
|
|
prep.recalculate_flag = (PREP_FLAG_HOLD_PARTIAL_BLOCK | PREP_FLAG_RECALCULATE);
|
|
prep.req_mm_increment = REQ_MM_INCREMENT_SCALAR/prep.step_per_mm; // Recompute this value.
|
|
} else {
|
|
prep.recalculate_flag = false;
|
|
}
|
|
pl_block = NULL; // Set to reload next block.
|
|
}
|
|
#endif
|
|
|
|
|
|
/* Prepares step segment buffer. Continuously called from main program.
|
|
|
|
The segment buffer is an intermediary buffer interface between the execution of steps
|
|
by the stepper algorithm and the velocity profiles generated by the planner. The stepper
|
|
algorithm only executes steps within the segment buffer and is filled by the main program
|
|
when steps are "checked-out" from the first block in the planner buffer. This keeps the
|
|
step execution and planning optimization processes atomic and protected from each other.
|
|
The number of steps "checked-out" from the planner buffer and the number of segments in
|
|
the segment buffer is sized and computed such that no operation in the main program takes
|
|
longer than the time it takes the stepper algorithm to empty it before refilling it.
|
|
Currently, the segment buffer conservatively holds roughly up to 40-50 msec of steps.
|
|
NOTE: Computation units are in steps, millimeters, and minutes.
|
|
*/
|
|
void st_prep_buffer()
|
|
{
|
|
// Block step prep buffer, while in a suspend state and there is no suspend motion to execute.
|
|
if (bit_istrue(sys.step_control,STEP_CONTROL_END_MOTION)) { return; }
|
|
|
|
while (segment_buffer_tail != segment_next_head) { // Check if we need to fill the buffer.
|
|
|
|
// Determine if we need to load a new planner block or if the block needs to be recomputed.
|
|
if (pl_block == NULL) {
|
|
|
|
// Query planner for a queued block
|
|
if (sys.step_control & STEP_CONTROL_EXECUTE_SYS_MOTION) { pl_block = plan_get_system_motion_block(); }
|
|
else { pl_block = plan_get_current_block(); }
|
|
if (pl_block == NULL) { return; } // No planner blocks. Exit.
|
|
|
|
// Check if we need to only recompute the velocity profile or load a new block.
|
|
if (prep.recalculate_flag & PREP_FLAG_RECALCULATE) {
|
|
|
|
#ifdef PARKING_ENABLE
|
|
if (prep.recalculate_flag & PREP_FLAG_PARKING) { prep.recalculate_flag &= ~(PREP_FLAG_RECALCULATE); }
|
|
else { prep.recalculate_flag = false; }
|
|
#else
|
|
prep.recalculate_flag = false;
|
|
#endif
|
|
|
|
} else {
|
|
|
|
// Load the Bresenham stepping data for the block.
|
|
prep.st_block_index = st_next_block_index(prep.st_block_index);
|
|
|
|
// Prepare and copy Bresenham algorithm segment data from the new planner block, so that
|
|
// when the segment buffer completes the planner block, it may be discarded when the
|
|
// segment buffer finishes the prepped block, but the stepper ISR is still executing it.
|
|
st_prep_block = &st_block_buffer[prep.st_block_index];
|
|
st_prep_block->direction_bits = pl_block->direction_bits;
|
|
uint8_t idx;
|
|
#ifndef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
|
|
for (idx=0; idx<N_AXIS; idx++) { st_prep_block->steps[idx] = pl_block->steps[idx]; }
|
|
st_prep_block->step_event_count = pl_block->step_event_count;
|
|
#else
|
|
// With AMASS enabled, simply bit-shift multiply all Bresenham data by the max AMASS
|
|
// level, such that we never divide beyond the original data anywhere in the algorithm.
|
|
// If the original data is divided, we can lose a step from integer roundoff.
|
|
for (idx=0; idx<N_AXIS; idx++) { st_prep_block->steps[idx] = pl_block->steps[idx] << MAX_AMASS_LEVEL; }
|
|
st_prep_block->step_event_count = pl_block->step_event_count << MAX_AMASS_LEVEL;
|
|
#endif
|
|
|
|
// Initialize segment buffer data for generating the segments.
|
|
prep.steps_remaining = (float)pl_block->step_event_count;
|
|
prep.step_per_mm = prep.steps_remaining/pl_block->millimeters;
|
|
prep.req_mm_increment = REQ_MM_INCREMENT_SCALAR/prep.step_per_mm;
|
|
prep.dt_remainder = 0.0; // Reset for new segment block
|
|
|
|
if ((sys.step_control & STEP_CONTROL_EXECUTE_HOLD) || (prep.recalculate_flag & PREP_FLAG_DECEL_OVERRIDE)) {
|
|
// New block loaded mid-hold. Override planner block entry speed to enforce deceleration.
|
|
prep.current_speed = prep.exit_speed;
|
|
pl_block->entry_speed_sqr = prep.exit_speed*prep.exit_speed;
|
|
prep.recalculate_flag &= ~(PREP_FLAG_DECEL_OVERRIDE);
|
|
} else {
|
|
prep.current_speed = sqrt(pl_block->entry_speed_sqr);
|
|
}
|
|
|
|
// Setup laser mode variables. PWM rate adjusted motions will always complete a motion with the
|
|
// spindle off.
|
|
st_prep_block->is_pwm_rate_adjusted = false;
|
|
if (settings.flags & BITFLAG_LASER_MODE) {
|
|
if (pl_block->condition & PL_COND_FLAG_SPINDLE_CCW) {
|
|
// Pre-compute inverse programmed rate to speed up PWM updating per step segment.
|
|
prep.inv_rate = 1.0/pl_block->programmed_rate;
|
|
st_prep_block->is_pwm_rate_adjusted = true;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* ---------------------------------------------------------------------------------
|
|
Compute the velocity profile of a new planner block based on its entry and exit
|
|
speeds, or recompute the profile of a partially-completed planner block if the
|
|
planner has updated it. For a commanded forced-deceleration, such as from a feed
|
|
hold, override the planner velocities and decelerate to the target exit speed.
|
|
*/
|
|
prep.mm_complete = 0.0; // Default velocity profile complete at 0.0mm from end of block.
|
|
float inv_2_accel = 0.5/pl_block->acceleration;
|
|
if (sys.step_control & STEP_CONTROL_EXECUTE_HOLD) { // [Forced Deceleration to Zero Velocity]
|
|
// Compute velocity profile parameters for a feed hold in-progress. This profile overrides
|
|
// the planner block profile, enforcing a deceleration to zero speed.
|
|
prep.ramp_type = RAMP_DECEL;
|
|
// Compute decelerate distance relative to end of block.
|
|
float decel_dist = pl_block->millimeters - inv_2_accel*pl_block->entry_speed_sqr;
|
|
if (decel_dist < 0.0) {
|
|
// Deceleration through entire planner block. End of feed hold is not in this block.
|
|
prep.exit_speed = sqrt(pl_block->entry_speed_sqr-2*pl_block->acceleration*pl_block->millimeters);
|
|
} else {
|
|
prep.mm_complete = decel_dist; // End of feed hold.
|
|
prep.exit_speed = 0.0;
|
|
}
|
|
} else { // [Normal Operation]
|
|
// Compute or recompute velocity profile parameters of the prepped planner block.
|
|
prep.ramp_type = RAMP_ACCEL; // Initialize as acceleration ramp.
|
|
prep.accelerate_until = pl_block->millimeters;
|
|
|
|
float exit_speed_sqr;
|
|
float nominal_speed;
|
|
if (sys.step_control & STEP_CONTROL_EXECUTE_SYS_MOTION) {
|
|
prep.exit_speed = exit_speed_sqr = 0.0; // Enforce stop at end of system motion.
|
|
} else {
|
|
exit_speed_sqr = plan_get_exec_block_exit_speed_sqr();
|
|
prep.exit_speed = sqrt(exit_speed_sqr);
|
|
}
|
|
|
|
nominal_speed = plan_compute_profile_nominal_speed(pl_block);
|
|
float nominal_speed_sqr = nominal_speed*nominal_speed;
|
|
float intersect_distance =
|
|
0.5*(pl_block->millimeters+inv_2_accel*(pl_block->entry_speed_sqr-exit_speed_sqr));
|
|
|
|
if (pl_block->entry_speed_sqr > nominal_speed_sqr) { // Only occurs during override reductions.
|
|
prep.accelerate_until = pl_block->millimeters - inv_2_accel*(pl_block->entry_speed_sqr-nominal_speed_sqr);
|
|
if (prep.accelerate_until <= 0.0) { // Deceleration-only.
|
|
prep.ramp_type = RAMP_DECEL;
|
|
// prep.decelerate_after = pl_block->millimeters;
|
|
// prep.maximum_speed = prep.current_speed;
|
|
|
|
// Compute override block exit speed since it doesn't match the planner exit speed.
|
|
prep.exit_speed = sqrt(pl_block->entry_speed_sqr - 2*pl_block->acceleration*pl_block->millimeters);
|
|
prep.recalculate_flag |= PREP_FLAG_DECEL_OVERRIDE; // Flag to load next block as deceleration override.
|
|
|
|
// TODO: Determine correct handling of parameters in deceleration-only.
|
|
// Can be tricky since entry speed will be current speed, as in feed holds.
|
|
// Also, look into near-zero speed handling issues with this.
|
|
|
|
} else {
|
|
// Decelerate to cruise or cruise-decelerate types. Guaranteed to intersect updated plan.
|
|
prep.decelerate_after = inv_2_accel*(nominal_speed_sqr-exit_speed_sqr);
|
|
prep.maximum_speed = nominal_speed;
|
|
prep.ramp_type = RAMP_DECEL_OVERRIDE;
|
|
}
|
|
} else if (intersect_distance > 0.0) {
|
|
if (intersect_distance < pl_block->millimeters) { // Either trapezoid or triangle types
|
|
// NOTE: For acceleration-cruise and cruise-only types, following calculation will be 0.0.
|
|
prep.decelerate_after = inv_2_accel*(nominal_speed_sqr-exit_speed_sqr);
|
|
if (prep.decelerate_after < intersect_distance) { // Trapezoid type
|
|
prep.maximum_speed = nominal_speed;
|
|
if (pl_block->entry_speed_sqr == nominal_speed_sqr) {
|
|
// Cruise-deceleration or cruise-only type.
|
|
prep.ramp_type = RAMP_CRUISE;
|
|
} else {
|
|
// Full-trapezoid or acceleration-cruise types
|
|
prep.accelerate_until -= inv_2_accel*(nominal_speed_sqr-pl_block->entry_speed_sqr);
|
|
}
|
|
} else { // Triangle type
|
|
prep.accelerate_until = intersect_distance;
|
|
prep.decelerate_after = intersect_distance;
|
|
prep.maximum_speed = sqrt(2.0*pl_block->acceleration*intersect_distance+exit_speed_sqr);
|
|
}
|
|
} else { // Deceleration-only type
|
|
prep.ramp_type = RAMP_DECEL;
|
|
// prep.decelerate_after = pl_block->millimeters;
|
|
// prep.maximum_speed = prep.current_speed;
|
|
}
|
|
} else { // Acceleration-only type
|
|
prep.accelerate_until = 0.0;
|
|
// prep.decelerate_after = 0.0;
|
|
prep.maximum_speed = prep.exit_speed;
|
|
}
|
|
}
|
|
|
|
#ifdef VARIABLE_SPINDLE
|
|
bit_true(sys.step_control, STEP_CONTROL_UPDATE_SPINDLE_PWM); // Force update whenever updating block.
|
|
#endif
|
|
}
|
|
|
|
// Initialize new segment
|
|
segment_t *prep_segment = &segment_buffer[segment_buffer_head];
|
|
|
|
// Set new segment to point to the current segment data block.
|
|
prep_segment->st_block_index = prep.st_block_index;
|
|
|
|
/*------------------------------------------------------------------------------------
|
|
Compute the average velocity of this new segment by determining the total distance
|
|
traveled over the segment time DT_SEGMENT. The following code first attempts to create
|
|
a full segment based on the current ramp conditions. If the segment time is incomplete
|
|
when terminating at a ramp state change, the code will continue to loop through the
|
|
progressing ramp states to fill the remaining segment execution time. However, if
|
|
an incomplete segment terminates at the end of the velocity profile, the segment is
|
|
considered completed despite having a truncated execution time less than DT_SEGMENT.
|
|
The velocity profile is always assumed to progress through the ramp sequence:
|
|
acceleration ramp, cruising state, and deceleration ramp. Each ramp's travel distance
|
|
may range from zero to the length of the block. Velocity profiles can end either at
|
|
the end of planner block (typical) or mid-block at the end of a forced deceleration,
|
|
such as from a feed hold.
|
|
*/
|
|
float dt_max = DT_SEGMENT; // Maximum segment time
|
|
float dt = 0.0; // Initialize segment time
|
|
float time_var = dt_max; // Time worker variable
|
|
float mm_var; // mm-Distance worker variable
|
|
float speed_var; // Speed worker variable
|
|
float mm_remaining = pl_block->millimeters; // New segment distance from end of block.
|
|
float minimum_mm = mm_remaining-prep.req_mm_increment; // Guarantee at least one step.
|
|
if (minimum_mm < 0.0) { minimum_mm = 0.0; }
|
|
|
|
do {
|
|
switch (prep.ramp_type) {
|
|
case RAMP_DECEL_OVERRIDE:
|
|
speed_var = pl_block->acceleration*time_var;
|
|
mm_var = time_var*(prep.current_speed - 0.5*speed_var);
|
|
mm_remaining -= mm_var;
|
|
if ((mm_remaining < prep.accelerate_until) || (mm_var <= 0)) {
|
|
// Cruise or cruise-deceleration types only for deceleration override.
|
|
mm_remaining = prep.accelerate_until; // NOTE: 0.0 at EOB
|
|
time_var = 2.0*(pl_block->millimeters-mm_remaining)/(prep.current_speed+prep.maximum_speed);
|
|
prep.ramp_type = RAMP_CRUISE;
|
|
prep.current_speed = prep.maximum_speed;
|
|
} else { // Mid-deceleration override ramp.
|
|
prep.current_speed -= speed_var;
|
|
}
|
|
break;
|
|
case RAMP_ACCEL:
|
|
// NOTE: Acceleration ramp only computes during first do-while loop.
|
|
speed_var = pl_block->acceleration*time_var;
|
|
mm_remaining -= time_var*(prep.current_speed + 0.5*speed_var);
|
|
if (mm_remaining < prep.accelerate_until) { // End of acceleration ramp.
|
|
// Acceleration-cruise, acceleration-deceleration ramp junction, or end of block.
|
|
mm_remaining = prep.accelerate_until; // NOTE: 0.0 at EOB
|
|
time_var = 2.0*(pl_block->millimeters-mm_remaining)/(prep.current_speed+prep.maximum_speed);
|
|
if (mm_remaining == prep.decelerate_after) { prep.ramp_type = RAMP_DECEL; }
|
|
else { prep.ramp_type = RAMP_CRUISE; }
|
|
prep.current_speed = prep.maximum_speed;
|
|
} else { // Acceleration only.
|
|
prep.current_speed += speed_var;
|
|
}
|
|
break;
|
|
case RAMP_CRUISE:
|
|
// NOTE: mm_var used to retain the last mm_remaining for incomplete segment time_var calculations.
|
|
// NOTE: If maximum_speed*time_var value is too low, round-off can cause mm_var to not change. To
|
|
// prevent this, simply enforce a minimum speed threshold in the planner.
|
|
mm_var = mm_remaining - prep.maximum_speed*time_var;
|
|
if (mm_var < prep.decelerate_after) { // End of cruise.
|
|
// Cruise-deceleration junction or end of block.
|
|
time_var = (mm_remaining - prep.decelerate_after)/prep.maximum_speed;
|
|
mm_remaining = prep.decelerate_after; // NOTE: 0.0 at EOB
|
|
prep.ramp_type = RAMP_DECEL;
|
|
} else { // Cruising only.
|
|
mm_remaining = mm_var;
|
|
}
|
|
break;
|
|
default: // case RAMP_DECEL:
|
|
// NOTE: mm_var used as a misc worker variable to prevent errors when near zero speed.
|
|
speed_var = pl_block->acceleration*time_var; // Used as delta speed (mm/min)
|
|
if (prep.current_speed > speed_var) { // Check if at or below zero speed.
|
|
// Compute distance from end of segment to end of block.
|
|
mm_var = mm_remaining - time_var*(prep.current_speed - 0.5*speed_var); // (mm)
|
|
if (mm_var > prep.mm_complete) { // Typical case. In deceleration ramp.
|
|
mm_remaining = mm_var;
|
|
prep.current_speed -= speed_var;
|
|
break; // Segment complete. Exit switch-case statement. Continue do-while loop.
|
|
}
|
|
}
|
|
// Otherwise, at end of block or end of forced-deceleration.
|
|
time_var = 2.0*(mm_remaining-prep.mm_complete)/(prep.current_speed+prep.exit_speed);
|
|
mm_remaining = prep.mm_complete;
|
|
prep.current_speed = prep.exit_speed;
|
|
}
|
|
dt += time_var; // Add computed ramp time to total segment time.
|
|
if (dt < dt_max) { time_var = dt_max - dt; } // **Incomplete** At ramp junction.
|
|
else {
|
|
if (mm_remaining > minimum_mm) { // Check for very slow segments with zero steps.
|
|
// Increase segment time to ensure at least one step in segment. Override and loop
|
|
// through distance calculations until minimum_mm or mm_complete.
|
|
dt_max += DT_SEGMENT;
|
|
time_var = dt_max - dt;
|
|
} else {
|
|
break; // **Complete** Exit loop. Segment execution time maxed.
|
|
}
|
|
}
|
|
} while (mm_remaining > prep.mm_complete); // **Complete** Exit loop. Profile complete.
|
|
|
|
#ifdef VARIABLE_SPINDLE
|
|
/* -----------------------------------------------------------------------------------
|
|
Compute spindle speed PWM output for step segment
|
|
*/
|
|
|
|
if (st_prep_block->is_pwm_rate_adjusted || (sys.step_control & STEP_CONTROL_UPDATE_SPINDLE_PWM)) {
|
|
if (pl_block->condition & (PL_COND_FLAG_SPINDLE_CW | PL_COND_FLAG_SPINDLE_CCW)) {
|
|
float rpm = pl_block->spindle_speed;
|
|
// NOTE: Feed and rapid overrides are independent of PWM value and do not alter laser power/rate.
|
|
if (st_prep_block->is_pwm_rate_adjusted) { rpm *= (prep.current_speed * prep.inv_rate); }
|
|
// If current_speed is zero, then may need to be rpm_min*(100/MAX_SPINDLE_SPEED_OVERRIDE)
|
|
// but this would be instantaneous only and during a motion. May not matter at all.
|
|
prep.current_spindle_pwm = spindle_compute_pwm_value(rpm);
|
|
} else {
|
|
sys.spindle_speed = 0.0;
|
|
prep.current_spindle_pwm = SPINDLE_PWM_OFF_VALUE;
|
|
}
|
|
bit_false(sys.step_control,STEP_CONTROL_UPDATE_SPINDLE_PWM);
|
|
}
|
|
prep_segment->spindle_pwm = prep.current_spindle_pwm; // Reload segment PWM value
|
|
|
|
#endif
|
|
|
|
/* -----------------------------------------------------------------------------------
|
|
Compute segment step rate, steps to execute, and apply necessary rate corrections.
|
|
NOTE: Steps are computed by direct scalar conversion of the millimeter distance
|
|
remaining in the block, rather than incrementally tallying the steps executed per
|
|
segment. This helps in removing floating point round-off issues of several additions.
|
|
However, since floats have only 7.2 significant digits, long moves with extremely
|
|
high step counts can exceed the precision of floats, which can lead to lost steps.
|
|
Fortunately, this scenario is highly unlikely and unrealistic in CNC machines
|
|
supported by Grbl (i.e. exceeding 10 meters axis travel at 200 step/mm).
|
|
*/
|
|
float step_dist_remaining = prep.step_per_mm*mm_remaining; // Convert mm_remaining to steps
|
|
float n_steps_remaining = ceil(step_dist_remaining); // Round-up current steps remaining
|
|
float last_n_steps_remaining = ceil(prep.steps_remaining); // Round-up last steps remaining
|
|
prep_segment->n_step = last_n_steps_remaining-n_steps_remaining; // Compute number of steps to execute.
|
|
|
|
// Bail if we are at the end of a feed hold and don't have a step to execute.
|
|
if (prep_segment->n_step == 0) {
|
|
if (sys.step_control & STEP_CONTROL_EXECUTE_HOLD) {
|
|
// Less than one step to decelerate to zero speed, but already very close. AMASS
|
|
// requires full steps to execute. So, just bail.
|
|
bit_true(sys.step_control,STEP_CONTROL_END_MOTION);
|
|
#ifdef PARKING_ENABLE
|
|
if (!(prep.recalculate_flag & PREP_FLAG_PARKING)) { prep.recalculate_flag |= PREP_FLAG_HOLD_PARTIAL_BLOCK; }
|
|
#endif
|
|
return; // Segment not generated, but current step data still retained.
|
|
}
|
|
}
|
|
|
|
// Compute segment step rate. Since steps are integers and mm distances traveled are not,
|
|
// the end of every segment can have a partial step of varying magnitudes that are not
|
|
// executed, because the stepper ISR requires whole steps due to the AMASS algorithm. To
|
|
// compensate, we track the time to execute the previous segment's partial step and simply
|
|
// apply it with the partial step distance to the current segment, so that it minutely
|
|
// adjusts the whole segment rate to keep step output exact. These rate adjustments are
|
|
// typically very small and do not adversely effect performance, but ensures that Grbl
|
|
// outputs the exact acceleration and velocity profiles as computed by the planner.
|
|
dt += prep.dt_remainder; // Apply previous segment partial step execute time
|
|
float inv_rate = dt/(last_n_steps_remaining - step_dist_remaining); // Compute adjusted step rate inverse
|
|
|
|
// Compute CPU cycles per step for the prepped segment.
|
|
uint32_t cycles = ceil( (TICKS_PER_MICROSECOND*1000000*60)*inv_rate ); // (cycles/step)
|
|
|
|
#ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
|
|
// Compute step timing and multi-axis smoothing level.
|
|
// NOTE: AMASS overdrives the timer with each level, so only one prescalar is required.
|
|
if (cycles < AMASS_LEVEL1) { prep_segment->amass_level = 0; }
|
|
else {
|
|
if (cycles < AMASS_LEVEL2) { prep_segment->amass_level = 1; }
|
|
else if (cycles < AMASS_LEVEL3) { prep_segment->amass_level = 2; }
|
|
else { prep_segment->amass_level = 3; }
|
|
cycles >>= prep_segment->amass_level;
|
|
prep_segment->n_step <<= prep_segment->amass_level;
|
|
}
|
|
if (cycles < (1UL << 16)) { prep_segment->cycles_per_tick = cycles; } // < 65536 (4.1ms @ 16MHz)
|
|
else { prep_segment->cycles_per_tick = 0xffff; } // Just set the slowest speed possible.
|
|
#else
|
|
// Compute step timing and timer prescalar for normal step generation.
|
|
if (cycles < (1UL << 16)) { // < 65536 (4.1ms @ 16MHz)
|
|
prep_segment->prescaler = 1; // prescaler: 0
|
|
prep_segment->cycles_per_tick = cycles;
|
|
} else if (cycles < (1UL << 19)) { // < 524288 (32.8ms@16MHz)
|
|
prep_segment->prescaler = 2; // prescaler: 8
|
|
prep_segment->cycles_per_tick = cycles >> 3;
|
|
} else {
|
|
prep_segment->prescaler = 3; // prescaler: 64
|
|
if (cycles < (1UL << 22)) { // < 4194304 (262ms@16MHz)
|
|
prep_segment->cycles_per_tick = cycles >> 6;
|
|
} else { // Just set the slowest speed possible. (Around 4 step/sec.)
|
|
prep_segment->cycles_per_tick = 0xffff;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
// Segment complete! Increment segment buffer indices, so stepper ISR can immediately execute it.
|
|
segment_buffer_head = segment_next_head;
|
|
if ( ++segment_next_head == SEGMENT_BUFFER_SIZE ) { segment_next_head = 0; }
|
|
|
|
// Update the appropriate planner and segment data.
|
|
pl_block->millimeters = mm_remaining;
|
|
prep.steps_remaining = n_steps_remaining;
|
|
prep.dt_remainder = (n_steps_remaining - step_dist_remaining)*inv_rate;
|
|
|
|
// Check for exit conditions and flag to load next planner block.
|
|
if (mm_remaining == prep.mm_complete) {
|
|
// End of planner block or forced-termination. No more distance to be executed.
|
|
if (mm_remaining > 0.0) { // At end of forced-termination.
|
|
// Reset prep parameters for resuming and then bail. Allow the stepper ISR to complete
|
|
// the segment queue, where realtime protocol will set new state upon receiving the
|
|
// cycle stop flag from the ISR. Prep_segment is blocked until then.
|
|
bit_true(sys.step_control,STEP_CONTROL_END_MOTION);
|
|
#ifdef PARKING_ENABLE
|
|
if (!(prep.recalculate_flag & PREP_FLAG_PARKING)) { prep.recalculate_flag |= PREP_FLAG_HOLD_PARTIAL_BLOCK; }
|
|
#endif
|
|
return; // Bail!
|
|
} else { // End of planner block
|
|
// The planner block is complete. All steps are set to be executed in the segment buffer.
|
|
if (sys.step_control & STEP_CONTROL_EXECUTE_SYS_MOTION) {
|
|
bit_true(sys.step_control,STEP_CONTROL_END_MOTION);
|
|
return;
|
|
}
|
|
pl_block = NULL; // Set pointer to indicate check and load next planner block.
|
|
plan_discard_current_block();
|
|
}
|
|
}
|
|
|
|
}
|
|
}
|
|
|
|
|
|
// Called by realtime status reporting to fetch the current speed being executed. This value
|
|
// however is not exactly the current speed, but the speed computed in the last step segment
|
|
// in the segment buffer. It will always be behind by up to the number of segment blocks (-1)
|
|
// divided by the ACCELERATION TICKS PER SECOND in seconds.
|
|
float st_get_realtime_rate()
|
|
{
|
|
if (sys.state & (STATE_CYCLE | STATE_HOMING | STATE_HOLD | STATE_JOG | STATE_SAFETY_DOOR)){
|
|
return prep.current_speed;
|
|
}
|
|
return 0.0f;
|
|
}
|