grbl-LPC-CoreXY/limits.c

/*
  limits.c - code pertaining to limit-switches and performing the homing cycle
  Part of Grbl

  The MIT License (MIT)

  GRBL(tm) - Embedded CNC g-code interpreter and motion-controller
  Copyright (c) 2009-2011 Simen Svale Skogsrud
  Copyright (c) 2012 Sungeun K. Jeon

  Permission is hereby granted, free of charge, to any person obtaining a copy
  of this software and associated documentation files (the "Software"), to deal
  in the Software without restriction, including without limitation the rights
  to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
  copies of the Software, and to permit persons to whom the Software is
  furnished to do so, subject to the following conditions:

  The above copyright notice and this permission notice shall be included in
  all copies or substantial portions of the Software.

  THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
  IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
  FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
  AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
  LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
  OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
  THE SOFTWARE.
*/  
#include <util/delay.h>
#include <avr/io.h>
#include <avr/interrupt.h>
#include "stepper.h"
#include "settings.h"
#include "nuts_bolts.h"
#include "config.h"
#include "spindle_control.h"
#include "motion_control.h"
#include "planner.h"
#include "protocol.h"
#include "limits.h"
#include "report.h"

#define MICROSECONDS_PER_ACCELERATION_TICK  (1000000/ACCELERATION_TICKS_PER_SECOND)

void limits_init() 
{
  LIMIT_DDR &= ~(LIMIT_MASK); // Set as input pins
  #ifndef LIMIT_SWITCHES_ACTIVE_HIGH
    LIMIT_PORT |= (LIMIT_MASK); // Enable internal pull-up resistors. Normal high operation.
  #else // LIMIT_SWITCHES_ACTIVE_HIGH
    LIMIT_PORT &= ~(LIMIT_MASK); // Normal low operation. Requires external pull-down.
  #endif // !LIMIT_SWITCHES_ACTIVE_HIGH
  if (bit_istrue(settings.flags,BITFLAG_HARD_LIMIT_ENABLE)) {
    LIMIT_PCMSK |= LIMIT_MASK; // Enable specific pins of the Pin Change Interrupt
    PCICR |= (1 << LIMIT_INT); // Enable Pin Change Interrupt
  } else {
    LIMIT_PCMSK &= ~LIMIT_MASK; // Disable
    PCICR &= ~(1 << LIMIT_INT); 
  }
}

// This is the Limit Pin Change Interrupt, which handles the hard limit feature. A bouncing 
// limit switch can cause a lot of problems, like false readings and multiple interrupt calls.
// If a switch is triggered at all, something bad has happened and treat it as such, regardless
// if a limit switch is being disengaged. It's impossible to reliably tell the state of a 
// bouncing pin without a debouncing method.
// NOTE: Do not attach an e-stop to the limit pins, because this interrupt is disabled during
// homing cycles and will not respond correctly. Upon user request or need, there may be a
// special pinout for an e-stop, but it is generally recommended to just directly connect
// your e-stop switch to the Arduino reset pin, since it is the most correct way to do this.
ISR(LIMIT_INT_vect) 
{
  // TODO: This interrupt may be used to manage the homing cycle directly with the main stepper
  // interrupt without adding too much to it. All it would need is some way to stop one axis 
  // when its limit is triggered and continue the others. This may reduce some of the code, but
  // would make Grbl a little harder to read and understand down road. Holding off on this until
  // we move on to new hardware or flash space becomes an issue. If it ain't broke, don't fix it.

  // Ignore limit switches if already in an alarm state or in-process of executing an alarm.
  // When in the alarm state, Grbl should have been reset or will force a reset, so any pending 
  // moves in the planner and serial buffers are all cleared and newly sent blocks will be 
  // locked out until a homing cycle or a kill lock command. Allows the user to disable the hard
  // limit setting if their limits are constantly triggering after a reset and move their axes.
  if (sys.state != STATE_ALARM) { 
    if (bit_isfalse(sys.execute,EXEC_ALARM)) {
      mc_reset(); // Initiate system kill.
      sys.execute |= EXEC_CRIT_EVENT; // Indicate hard limit critical event
    }
  }
}


// Moves all specified axes in same specified direction (positive=true, negative=false)
// and at the homing rate. Homing is a special motion case, where there is only an 
// acceleration followed by abrupt asynchronous stops by each axes reaching their limit 
// switch independently. Instead of shoehorning homing cycles into the main stepper 
// algorithm and overcomplicate things, a stripped-down, lite version of the stepper 
// algorithm is written here. This also lets users hack and tune this code freely for
// their own particular needs without affecting the rest of Grbl.
// NOTE: Only the abort runtime command can interrupt this process.
static void homing_cycle(uint8_t cycle_mask, int8_t pos_dir, bool invert_pin, float homing_rate) 
{
  #ifdef LIMIT_SWITCHES_ACTIVE_HIGH
    // When in an active-high switch configuration, invert_pin needs to be adjusted.
    invert_pin = !invert_pin;
  #endif

  // Determine governing axes with finest step resolution per distance for the Bresenham
  // algorithm. This solves the issue when homing multiple axes that have different 
  // resolutions without exceeding system acceleration setting. It doesn't have to be
  // perfect since homing locates machine zero, but should create for a more consistent 
  // and speedy homing routine.
  // NOTE: For each axes enabled, the following calculations assume they physically move 
  // an equal distance over each time step until they hit a limit switch, aka dogleg.
  uint32_t steps[3];
  uint8_t dist = 0;
  clear_vector(steps);
  if (cycle_mask & (1<<X_AXIS)) { 
    dist++;
    steps[X_AXIS] = lround(settings.steps_per_mm[X_AXIS]); 
  }
  if (cycle_mask & (1<<Y_AXIS)) { 
    dist++;
    steps[Y_AXIS] = lround(settings.steps_per_mm[Y_AXIS]); 
  }
  if (cycle_mask & (1<<Z_AXIS)) {
    dist++;
    steps[Z_AXIS] = lround(settings.steps_per_mm[Z_AXIS]);
  }
  uint32_t step_event_count = max(steps[X_AXIS], max(steps[Y_AXIS], steps[Z_AXIS]));  
  
  // To ensure global acceleration is not exceeded, reduce the governing axes nominal rate
  // by adjusting the actual axes distance traveled per step. This is the same procedure
  // used in the main planner to account for distance traveled when moving multiple axes.
  // NOTE: When axis acceleration independence is installed, this will be updated to move
  // all axes at their maximum acceleration and rate.
  float ds = step_event_count/sqrt(dist);

  // Compute the adjusted step rate change with each acceleration tick. (in step/min/acceleration_tick)
  uint32_t delta_rate = ceil( ds*settings.acceleration/(60*ACCELERATION_TICKS_PER_SECOND));
  
  #ifdef HOMING_RATE_ADJUST
    // Adjust homing rate so a multiple axes moves all at the homing rate independently.
    homing_rate *= sqrt(dist); // Eq. only works if axes values are 1 or 0.
  #endif
  
  // Nominal and initial time increment per step. Nominal should always be greater then 3
  // usec, since they are based on the same parameters as the main stepper routine. Initial
  // is based on the MINIMUM_STEPS_PER_MINUTE config. Since homing feed can be very slow,
  // disable acceleration when rates are below MINIMUM_STEPS_PER_MINUTE.
  uint32_t dt_min = lround(1000000*60/(ds*homing_rate)); // Cruising (usec/step)
  uint32_t dt = 1000000*60/MINIMUM_STEPS_PER_MINUTE; // Initial (usec/step)
  if (dt > dt_min) { dt = dt_min; } // Disable acceleration for very slow rates.
      
  // Set default out_bits. 
  uint8_t out_bits0 = settings.invert_mask;
  out_bits0 ^= (settings.homing_dir_mask & DIRECTION_MASK); // Apply homing direction settings
  if (!pos_dir) { out_bits0 ^= DIRECTION_MASK; }   // Invert bits, if negative dir.
  
  // Initialize stepping variables
  int32_t counter_x = -(step_event_count >> 1); // Bresenham counters
  int32_t counter_y = counter_x;
  int32_t counter_z = counter_x;
  uint32_t step_delay = dt-settings.pulse_microseconds;  // Step delay after pulse
  uint32_t step_rate = 0;  // Tracks step rate. Initialized from 0 rate. (in step/min)
  uint32_t trap_counter = MICROSECONDS_PER_ACCELERATION_TICK/2; // Acceleration trapezoid counter
  uint8_t out_bits;
  uint8_t limit_state;
  for(;;) {
  
    // Reset out bits. Both direction and step pins appropriately inverted and set.
    out_bits = out_bits0;
    
    // Get limit pin state.
    limit_state = LIMIT_PIN;
    if (invert_pin) { limit_state ^= LIMIT_MASK; } // If leaving switch, invert to move.
    
    // Set step pins by Bresenham line algorithm. If limit switch reached, disable and
    // flag for completion.
    if (cycle_mask & (1<<X_AXIS)) {
      counter_x += steps[X_AXIS];
      if (counter_x > 0) {
        if (limit_state & (1<<X_LIMIT_BIT)) { out_bits ^= (1<<X_STEP_BIT); }
        else { cycle_mask &= ~(1<<X_AXIS); }
        counter_x -= step_event_count;
      }
    }
    if (cycle_mask & (1<<Y_AXIS)) {
      counter_y += steps[Y_AXIS];
      if (counter_y > 0) {
        if (limit_state & (1<<Y_LIMIT_BIT)) { out_bits ^= (1<<Y_STEP_BIT); }
        else { cycle_mask &= ~(1<<Y_AXIS); }
        counter_y -= step_event_count;
      }
    }
    if (cycle_mask & (1<<Z_AXIS)) {
      counter_z += steps[Z_AXIS];
      if (counter_z > 0) {
        if (limit_state & (1<<Z_LIMIT_BIT)) { out_bits ^= (1<<Z_STEP_BIT); }
        else { cycle_mask &= ~(1<<Z_AXIS); }
        counter_z -= step_event_count;
      }
    }        
    
    // Check if we are done or for system abort
    if (!(cycle_mask) || (sys.execute & EXEC_RESET)) { return; }
        
    // Perform step.
    STEPPING_PORT = (STEPPING_PORT & ~STEP_MASK) | (out_bits & STEP_MASK);
    delay_us(settings.pulse_microseconds);
    STEPPING_PORT = out_bits0;
    delay_us(step_delay);
    
    // Track and set the next step delay, if required. This routine uses another Bresenham
    // line algorithm to follow the constant acceleration line in the velocity and time 
    // domain. This is a lite version of the same routine used in the main stepper program.
    if (dt > dt_min) { // Unless cruising, check for time update.
      trap_counter += dt; // Track time passed since last update.
      if (trap_counter > MICROSECONDS_PER_ACCELERATION_TICK) {
        trap_counter -= MICROSECONDS_PER_ACCELERATION_TICK;
        step_rate += delta_rate; // Increment velocity
        dt = (1000000*60)/step_rate; // Compute new time increment
        if (dt < dt_min) {dt = dt_min;}  // If target rate reached, cruise.
        step_delay = dt-settings.pulse_microseconds;
      }
    }
  }
}


void limits_go_home() 
{  
  // Enable only the steppers, not the cycle. Cycle should be inactive/complete.
  st_wake_up();
  
  // Search to engage all axes limit switches at faster homing seek rate.
  homing_cycle(HOMING_SEARCH_CYCLE_0, true, false, settings.homing_seek_rate);  // Search cycle 0
  #ifdef HOMING_SEARCH_CYCLE_1
    homing_cycle(HOMING_SEARCH_CYCLE_1, true, false, settings.homing_seek_rate);  // Search cycle 1
  #endif
  #ifdef HOMING_SEARCH_CYCLE_2
    homing_cycle(HOMING_SEARCH_CYCLE_2, true, false, settings.homing_seek_rate);  // Search cycle 2
  #endif
  delay_ms(settings.homing_debounce_delay); // Delay to debounce signal
    
  // Now in proximity of all limits. Carefully leave and approach switches in multiple cycles
  // to precisely hone in on the machine zero location. Moves at slower homing feed rate.
  int8_t n_cycle = N_HOMING_LOCATE_CYCLE;
  while (n_cycle--) {
    // Leave all switches to release them. After cycles complete, this is machine zero.
    homing_cycle(HOMING_LOCATE_CYCLE, false, true, settings.homing_feed_rate);
    delay_ms(settings.homing_debounce_delay);
    
    if (n_cycle > 0) {
      // Re-approach all switches to re-engage them.
      homing_cycle(HOMING_LOCATE_CYCLE, true, false, settings.homing_feed_rate);
      delay_ms(settings.homing_debounce_delay);
    }
  }

  st_go_idle(); // Call main stepper shutdown routine.  
}