cb916a996a
- Some laser controllers were reported to need a very high PWM frequency. Added a line to enable this in cpu_map.h, if needed. - Cleaned up some of the parking code. Mostly just editing the comments. - Moved the accessory state resetting after the initial parking retract. Should ensure the accessory state is properly handled upon an aborted parking restore. Not certain if this was a problem before though. Just to be sure.
163 lines
7.1 KiB
C
163 lines
7.1 KiB
C
/*
|
|
cpu_map.h - CPU and pin mapping configuration file
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2012-2016 Sungeun K. Jeon for Gnea Research LLC
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/* The cpu_map.h files serve as a central pin mapping selection file for different
|
|
processor types or alternative pin layouts. This version of Grbl officially supports
|
|
only the Arduino Mega328p. */
|
|
|
|
|
|
#ifndef cpu_map_h
|
|
#define cpu_map_h
|
|
|
|
|
|
#ifdef CPU_MAP_ATMEGA328P // (Arduino Uno) Officially supported by Grbl.
|
|
|
|
// Define serial port pins and interrupt vectors.
|
|
#define SERIAL_RX USART_RX_vect
|
|
#define SERIAL_UDRE USART_UDRE_vect
|
|
|
|
// Define step pulse output pins. NOTE: All step bit pins must be on the same port.
|
|
#define STEP_DDR DDRD
|
|
#define STEP_PORT PORTD
|
|
#define X_STEP_BIT 2 // Uno Digital Pin 2
|
|
#define Y_STEP_BIT 3 // Uno Digital Pin 3
|
|
#define Z_STEP_BIT 4 // Uno Digital Pin 4
|
|
#define STEP_MASK ((1<<X_STEP_BIT)|(1<<Y_STEP_BIT)|(1<<Z_STEP_BIT)) // All step bits
|
|
|
|
// Define step direction output pins. NOTE: All direction pins must be on the same port.
|
|
#define DIRECTION_DDR DDRD
|
|
#define DIRECTION_PORT PORTD
|
|
#define X_DIRECTION_BIT 5 // Uno Digital Pin 5
|
|
#define Y_DIRECTION_BIT 6 // Uno Digital Pin 6
|
|
#define Z_DIRECTION_BIT 7 // Uno Digital Pin 7
|
|
#define DIRECTION_MASK ((1<<X_DIRECTION_BIT)|(1<<Y_DIRECTION_BIT)|(1<<Z_DIRECTION_BIT)) // All direction bits
|
|
|
|
// Define stepper driver enable/disable output pin.
|
|
#define STEPPERS_DISABLE_DDR DDRB
|
|
#define STEPPERS_DISABLE_PORT PORTB
|
|
#define STEPPERS_DISABLE_BIT 0 // Uno Digital Pin 8
|
|
#define STEPPERS_DISABLE_MASK (1<<STEPPERS_DISABLE_BIT)
|
|
|
|
// Define homing/hard limit switch input pins and limit interrupt vectors.
|
|
// NOTE: All limit bit pins must be on the same port, but not on a port with other input pins (CONTROL).
|
|
#define LIMIT_DDR DDRB
|
|
#define LIMIT_PIN PINB
|
|
#define LIMIT_PORT PORTB
|
|
#define X_LIMIT_BIT 1 // Uno Digital Pin 9
|
|
#define Y_LIMIT_BIT 2 // Uno Digital Pin 10
|
|
#ifdef VARIABLE_SPINDLE // Z Limit pin and spindle enabled swapped to access hardware PWM on Pin 11.
|
|
#define Z_LIMIT_BIT 4 // Uno Digital Pin 12
|
|
#else
|
|
#define Z_LIMIT_BIT 3 // Uno Digital Pin 11
|
|
#endif
|
|
#define LIMIT_MASK ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)) // All limit bits
|
|
#define LIMIT_INT PCIE0 // Pin change interrupt enable pin
|
|
#define LIMIT_INT_vect PCINT0_vect
|
|
#define LIMIT_PCMSK PCMSK0 // Pin change interrupt register
|
|
|
|
// Define spindle enable and spindle direction output pins.
|
|
#define SPINDLE_ENABLE_DDR DDRB
|
|
#define SPINDLE_ENABLE_PORT PORTB
|
|
// Z Limit pin and spindle PWM/enable pin swapped to access hardware PWM on Pin 11.
|
|
#ifdef VARIABLE_SPINDLE
|
|
#ifdef USE_SPINDLE_DIR_AS_ENABLE_PIN
|
|
// If enabled, spindle direction pin now used as spindle enable, while PWM remains on D11.
|
|
#define SPINDLE_ENABLE_BIT 5 // Uno Digital Pin 13 (NOTE: D13 can't be pulled-high input due to LED.)
|
|
#else
|
|
#define SPINDLE_ENABLE_BIT 3 // Uno Digital Pin 11
|
|
#endif
|
|
#else
|
|
#define SPINDLE_ENABLE_BIT 4 // Uno Digital Pin 12
|
|
#endif
|
|
#ifndef USE_SPINDLE_DIR_AS_ENABLE_PIN
|
|
#define SPINDLE_DIRECTION_DDR DDRB
|
|
#define SPINDLE_DIRECTION_PORT PORTB
|
|
#define SPINDLE_DIRECTION_BIT 5 // Uno Digital Pin 13 (NOTE: D13 can't be pulled-high input due to LED.)
|
|
#endif
|
|
|
|
// Define flood and mist coolant enable output pins.
|
|
#define COOLANT_FLOOD_DDR DDRC
|
|
#define COOLANT_FLOOD_PORT PORTC
|
|
#define COOLANT_FLOOD_BIT 3 // Uno Analog Pin 3
|
|
#define COOLANT_MIST_DDR DDRC
|
|
#define COOLANT_MIST_PORT PORTC
|
|
#define COOLANT_MIST_BIT 4 // Uno Analog Pin 3
|
|
|
|
// Define user-control controls (cycle start, reset, feed hold) input pins.
|
|
// NOTE: All CONTROLs pins must be on the same port and not on a port with other input pins (limits).
|
|
#define CONTROL_DDR DDRC
|
|
#define CONTROL_PIN PINC
|
|
#define CONTROL_PORT PORTC
|
|
#define CONTROL_RESET_BIT 0 // Uno Analog Pin 0
|
|
#define CONTROL_FEED_HOLD_BIT 1 // Uno Analog Pin 1
|
|
#define CONTROL_CYCLE_START_BIT 2 // Uno Analog Pin 2
|
|
#define CONTROL_SAFETY_DOOR_BIT 1 // Uno Analog Pin 1 NOTE: Safety door is shared with feed hold. Enabled by config define.
|
|
#define CONTROL_INT PCIE1 // Pin change interrupt enable pin
|
|
#define CONTROL_INT_vect PCINT1_vect
|
|
#define CONTROL_PCMSK PCMSK1 // Pin change interrupt register
|
|
#define CONTROL_MASK ((1<<CONTROL_RESET_BIT)|(1<<CONTROL_FEED_HOLD_BIT)|(1<<CONTROL_CYCLE_START_BIT)|(1<<CONTROL_SAFETY_DOOR_BIT))
|
|
#define CONTROL_INVERT_MASK CONTROL_MASK // May be re-defined to only invert certain control pins.
|
|
|
|
// Define probe switch input pin.
|
|
#define PROBE_DDR DDRC
|
|
#define PROBE_PIN PINC
|
|
#define PROBE_PORT PORTC
|
|
#define PROBE_BIT 5 // Uno Analog Pin 5
|
|
#define PROBE_MASK (1<<PROBE_BIT)
|
|
|
|
// Variable spindle configuration below. Do not change unless you know what you are doing.
|
|
// NOTE: Only used when variable spindle is enabled.
|
|
#define SPINDLE_PWM_MAX_VALUE 255 // Don't change. 328p fast PWM mode fixes top value as 255.
|
|
#ifdef SPINDLE_MINIMUM_PWM
|
|
#define SPINDLE_PWM_MIN_VALUE SPINDLE_MINIMUM_PWM
|
|
#else
|
|
#define SPINDLE_PWM_MIN_VALUE 1 // Must be greater than zero.
|
|
#endif
|
|
#define SPINDLE_PWM_OFF_VALUE 0
|
|
#define SPINDLE_PWM_RANGE (SPINDLE_PWM_MAX_VALUE-SPINDLE_PWM_MIN_VALUE)
|
|
#define SPINDLE_TCCRA_REGISTER TCCR2A
|
|
#define SPINDLE_TCCRB_REGISTER TCCR2B
|
|
#define SPINDLE_OCR_REGISTER OCR2A
|
|
#define SPINDLE_COMB_BIT COM2A1
|
|
|
|
// Prescaled, 8-bit Fast PWM mode.
|
|
#define SPINDLE_TCCRA_INIT_MASK ((1<<WGM20) | (1<<WGM21)) // Configures fast PWM mode.
|
|
// #define SPINDLE_TCCRB_INIT_MASK (1<<CS20) // Disable prescaler -> 62.5kHz
|
|
// #define SPINDLE_TCCRB_INIT_MASK (1<<CS21) // 1/8 prescaler -> 7.8kHz (Used in v0.9)
|
|
// #define SPINDLE_TCCRB_INIT_MASK ((1<<CS21) | (1<<CS20)) // 1/32 prescaler -> 1.96kHz
|
|
#define SPINDLE_TCCRB_INIT_MASK (1<<CS22) // 1/64 prescaler -> 0.98kHz (J-tech laser)
|
|
|
|
// NOTE: On the 328p, these must be the same as the SPINDLE_ENABLE settings.
|
|
#define SPINDLE_PWM_DDR DDRB
|
|
#define SPINDLE_PWM_PORT PORTB
|
|
#define SPINDLE_PWM_BIT 3 // Uno Digital Pin 11
|
|
|
|
#endif
|
|
|
|
/*
|
|
#ifdef CPU_MAP_CUSTOM_PROC
|
|
// For a custom pin map or different processor, copy and edit one of the available cpu
|
|
// map files and modify it to your needs. Make sure the defined name is also changed in
|
|
// the config.h file.
|
|
#endif
|
|
*/
|
|
|
|
#endif
|