369 lines
16 KiB
C
369 lines
16 KiB
C
/*
|
|
limits.c - code pertaining to limit-switches and performing the homing cycle
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2012-2016 Sungeun K. Jeon for Gnea Research LLC
|
|
Copyright (c) 2009-2011 Simen Svale Skogsrud
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include "grbl.h"
|
|
|
|
|
|
// Homing axis search distance multiplier. Computed by this value times the cycle travel.
|
|
#ifndef HOMING_AXIS_SEARCH_SCALAR
|
|
#define HOMING_AXIS_SEARCH_SCALAR 1.5 // Must be > 1 to ensure limit switch will be engaged.
|
|
#endif
|
|
#ifndef HOMING_AXIS_LOCATE_SCALAR
|
|
#define HOMING_AXIS_LOCATE_SCALAR 5.0 // Must be > 1 to ensure limit switch is cleared.
|
|
#endif
|
|
|
|
void limits_init()
|
|
{
|
|
LIMIT_DDR &= ~(LIMIT_MASK); // Set as input pins
|
|
|
|
#ifdef DISABLE_LIMIT_PIN_PULL_UP
|
|
LIMIT_PORT &= ~(LIMIT_MASK); // Normal low operation. Requires external pull-down.
|
|
#else
|
|
LIMIT_PORT |= (LIMIT_MASK); // Enable internal pull-up resistors. Normal high operation.
|
|
#endif
|
|
|
|
if (bit_istrue(settings.flags,BITFLAG_HARD_LIMIT_ENABLE)) {
|
|
//LIMIT_PCMSK |= LIMIT_MASK; // Enable specific pins of the Pin Change Interrupt
|
|
//PCICR |= (1 << LIMIT_INT); // Enable Pin Change Interrupt
|
|
} else {
|
|
limits_disable();
|
|
}
|
|
|
|
#ifdef ENABLE_SOFTWARE_DEBOUNCE
|
|
MCUSR &= ~(1<<WDRF);
|
|
WDTCSR |= (1<<WDCE) | (1<<WDE);
|
|
WDTCSR = (1<<WDP0); // Set time-out at ~32msec.
|
|
#endif
|
|
}
|
|
|
|
|
|
// Disables hard limits.
|
|
void limits_disable()
|
|
{
|
|
//LIMIT_PCMSK &= ~LIMIT_MASK; // Disable specific pins of the Pin Change Interrupt
|
|
//PCICR &= ~(1 << LIMIT_INT); // Disable Pin Change Interrupt
|
|
}
|
|
|
|
|
|
// Returns limit state as a bit-wise uint8 variable. Each bit indicates an axis limit, where
|
|
// triggered is 1 and not triggered is 0. Invert mask is applied. Axes are defined by their
|
|
// number in bit position, i.e. Z_AXIS is (1<<2) or bit 2, and Y_AXIS is (1<<1) or bit 1.
|
|
uint8_t limits_get_state()
|
|
{
|
|
uint8_t limit_state = 0;
|
|
uint32_t pin = (LIMIT_PIN & LIMIT_MASK);
|
|
#ifdef INVERT_LIMIT_PIN_MASK
|
|
pin ^= INVERT_LIMIT_PIN_MASK;
|
|
#endif
|
|
if (bit_isfalse(settings.flags,BITFLAG_INVERT_LIMIT_PINS)) { pin ^= LIMIT_MASK; }
|
|
if (pin) {
|
|
uint8_t idx;
|
|
for (idx=0; idx<N_AXIS; idx++) {
|
|
if (pin & get_limit_pin_mask(idx)) { limit_state |= (1 << idx); }
|
|
}
|
|
}
|
|
return(limit_state);
|
|
}
|
|
|
|
|
|
// This is the Limit Pin Change Interrupt, which handles the hard limit feature. A bouncing
|
|
// limit switch can cause a lot of problems, like false readings and multiple interrupt calls.
|
|
// If a switch is triggered at all, something bad has happened and treat it as such, regardless
|
|
// if a limit switch is being disengaged. It's impossible to reliably tell the state of a
|
|
// bouncing pin because the Arduino microcontroller does not retain any state information when
|
|
// detecting a pin change. If we poll the pins in the ISR, you can miss the correct reading if the
|
|
// switch is bouncing.
|
|
// NOTE: Do not attach an e-stop to the limit pins, because this interrupt is disabled during
|
|
// homing cycles and will not respond correctly. Upon user request or need, there may be a
|
|
// special pinout for an e-stop, but it is generally recommended to just directly connect
|
|
// your e-stop switch to the Arduino reset pin, since it is the most correct way to do this.
|
|
#ifndef ENABLE_SOFTWARE_DEBOUNCE
|
|
ISR(LIMIT_INT_vect) // DEFAULT: Limit pin change interrupt process.
|
|
{
|
|
// Ignore limit switches if already in an alarm state or in-process of executing an alarm.
|
|
// When in the alarm state, Grbl should have been reset or will force a reset, so any pending
|
|
// moves in the planner and serial buffers are all cleared and newly sent blocks will be
|
|
// locked out until a homing cycle or a kill lock command. Allows the user to disable the hard
|
|
// limit setting if their limits are constantly triggering after a reset and move their axes.
|
|
if (sys.state != STATE_ALARM) {
|
|
if (!(sys_rt_exec_alarm)) {
|
|
#ifdef HARD_LIMIT_FORCE_STATE_CHECK
|
|
// Check limit pin state.
|
|
if (limits_get_state()) {
|
|
mc_reset(); // Initiate system kill.
|
|
system_set_exec_alarm(EXEC_ALARM_HARD_LIMIT); // Indicate hard limit critical event
|
|
}
|
|
#else
|
|
mc_reset(); // Initiate system kill.
|
|
system_set_exec_alarm(EXEC_ALARM_HARD_LIMIT); // Indicate hard limit critical event
|
|
#endif
|
|
}
|
|
}
|
|
}
|
|
#else // OPTIONAL: Software debounce limit pin routine.
|
|
// Upon limit pin change, enable watchdog timer to create a short delay.
|
|
ISR(LIMIT_INT_vect) { if (!(WDTCSR & (1<<WDIE))) { WDTCSR |= (1<<WDIE); } }
|
|
ISR(WDT_vect) // Watchdog timer ISR
|
|
{
|
|
WDTCSR &= ~(1<<WDIE); // Disable watchdog timer.
|
|
if (sys.state != STATE_ALARM) { // Ignore if already in alarm state.
|
|
if (!(sys_rt_exec_alarm)) {
|
|
// Check limit pin state.
|
|
if (limits_get_state()) {
|
|
mc_reset(); // Initiate system kill.
|
|
system_set_exec_alarm(EXEC_ALARM_HARD_LIMIT); // Indicate hard limit critical event
|
|
}
|
|
}
|
|
}
|
|
}
|
|
#endif
|
|
|
|
// Homes the specified cycle axes, sets the machine position, and performs a pull-off motion after
|
|
// completing. Homing is a special motion case, which involves rapid uncontrolled stops to locate
|
|
// the trigger point of the limit switches. The rapid stops are handled by a system level axis lock
|
|
// mask, which prevents the stepper algorithm from executing step pulses. Homing motions typically
|
|
// circumvent the processes for executing motions in normal operation.
|
|
// NOTE: Only the abort realtime command can interrupt this process.
|
|
// TODO: Move limit pin-specific calls to a general function for portability.
|
|
void limits_go_home(uint8_t cycle_mask)
|
|
{
|
|
if (sys.abort) { return; } // Block if system reset has been issued.
|
|
|
|
// Initialize plan data struct for homing motion. Spindle and coolant are disabled.
|
|
plan_line_data_t plan_data;
|
|
plan_line_data_t *pl_data = &plan_data;
|
|
memset(pl_data,0,sizeof(plan_line_data_t));
|
|
pl_data->condition = (PL_COND_FLAG_SYSTEM_MOTION|PL_COND_FLAG_NO_FEED_OVERRIDE);
|
|
#ifdef USE_LINE_NUMBERS
|
|
pl_data->line_number = HOMING_CYCLE_LINE_NUMBER;
|
|
#endif
|
|
|
|
// Initialize variables used for homing computations.
|
|
uint8_t n_cycle = (2*N_HOMING_LOCATE_CYCLE+1);
|
|
uint32_t step_pin[N_AXIS];
|
|
float target[N_AXIS];
|
|
float max_travel = 0.0;
|
|
uint8_t idx;
|
|
for (idx=0; idx<N_AXIS; idx++) {
|
|
// Initialize step pin masks
|
|
step_pin[idx] = get_step_pin_mask(idx);
|
|
#ifdef COREXY
|
|
if ((idx==A_MOTOR)||(idx==B_MOTOR)) { step_pin[idx] = (get_step_pin_mask(X_AXIS)|get_step_pin_mask(Y_AXIS)); }
|
|
#endif
|
|
|
|
if (bit_istrue(cycle_mask,bit(idx))) {
|
|
// Set target based on max_travel setting. Ensure homing switches engaged with search scalar.
|
|
// NOTE: settings.max_travel[] is stored as a negative value.
|
|
max_travel = max(max_travel,(-HOMING_AXIS_SEARCH_SCALAR)*settings.max_travel[idx]);
|
|
}
|
|
}
|
|
|
|
// Set search mode with approach at seek rate to quickly engage the specified cycle_mask limit switches.
|
|
bool approach = true;
|
|
float homing_rate = settings.homing_seek_rate;
|
|
|
|
uint32_t limit_state, axislock, n_active_axis;
|
|
do {
|
|
|
|
system_convert_array_steps_to_mpos(target,sys_position);
|
|
|
|
// Initialize and declare variables needed for homing routine.
|
|
axislock = 0;
|
|
n_active_axis = 0;
|
|
for (idx=0; idx<N_AXIS; idx++) {
|
|
// Set target location for active axes and setup computation for homing rate.
|
|
if (bit_istrue(cycle_mask,bit(idx))) {
|
|
n_active_axis++;
|
|
#ifdef COREXY
|
|
if (idx == X_AXIS) {
|
|
int32_t axis_position = system_convert_corexy_to_y_axis_steps(sys_position);
|
|
sys_position[A_MOTOR] = axis_position;
|
|
sys_position[B_MOTOR] = -axis_position;
|
|
} else if (idx == Y_AXIS) {
|
|
int32_t axis_position = system_convert_corexy_to_x_axis_steps(sys_position);
|
|
sys_position[A_MOTOR] = sys_position[B_MOTOR] = axis_position;
|
|
} else {
|
|
sys_position[Z_AXIS] = 0;
|
|
}
|
|
#else
|
|
sys_position[idx] = 0;
|
|
#endif
|
|
// Set target direction based on cycle mask and homing cycle approach state.
|
|
// NOTE: This happens to compile smaller than any other implementation tried.
|
|
if (bit_istrue(settings.homing_dir_mask,bit(idx))) {
|
|
if (approach) { target[idx] = -max_travel; }
|
|
else { target[idx] = max_travel; }
|
|
} else {
|
|
if (approach) { target[idx] = max_travel; }
|
|
else { target[idx] = -max_travel; }
|
|
}
|
|
// Apply axislock to the step port pins active in this cycle.
|
|
axislock |= step_pin[idx];
|
|
}
|
|
|
|
}
|
|
homing_rate *= sqrt(n_active_axis); // [sqrt(N_AXIS)] Adjust so individual axes all move at homing rate.
|
|
sys.homing_axis_lock = axislock;
|
|
|
|
// Perform homing cycle. Planner buffer should be empty, as required to initiate the homing cycle.
|
|
pl_data->feed_rate = homing_rate; // Set current homing rate.
|
|
plan_buffer_line(target, pl_data); // Bypass mc_line(). Directly plan homing motion.
|
|
|
|
sys.step_control = STEP_CONTROL_EXECUTE_SYS_MOTION; // Set to execute homing motion and clear existing flags.
|
|
st_prep_buffer(); // Prep and fill segment buffer from newly planned block.
|
|
st_wake_up(); // Initiate motion
|
|
do {
|
|
if (approach) {
|
|
// Check limit state. Lock out cycle axes when they change.
|
|
limit_state = limits_get_state();
|
|
for (idx=0; idx<N_AXIS; idx++) {
|
|
if (axislock & step_pin[idx]) {
|
|
if (limit_state & (1 << idx)) {
|
|
#ifdef COREXY
|
|
if (idx==Z_AXIS) { axislock &= ~(step_pin[Z_AXIS]); }
|
|
else { axislock &= ~(step_pin[A_MOTOR]|step_pin[B_MOTOR]); }
|
|
#else
|
|
axislock &= ~(step_pin[idx]);
|
|
#endif
|
|
}
|
|
}
|
|
}
|
|
sys.homing_axis_lock = axislock;
|
|
}
|
|
|
|
st_prep_buffer(); // Check and prep segment buffer. NOTE: Should take no longer than 200us.
|
|
|
|
// Exit routines: No time to run protocol_execute_realtime() in this loop.
|
|
if (sys_rt_exec_state & (EXEC_SAFETY_DOOR | EXEC_RESET | EXEC_CYCLE_STOP)) {
|
|
uint8_t rt_exec = sys_rt_exec_state;
|
|
// Homing failure condition: Reset issued during cycle.
|
|
if (rt_exec & EXEC_RESET) { system_set_exec_alarm(EXEC_ALARM_HOMING_FAIL_RESET); }
|
|
// Homing failure condition: Safety door was opened.
|
|
if (rt_exec & EXEC_SAFETY_DOOR) { system_set_exec_alarm(EXEC_ALARM_HOMING_FAIL_DOOR); }
|
|
// Homing failure condition: Limit switch still engaged after pull-off motion
|
|
if (!approach && (limits_get_state() & cycle_mask)) { system_set_exec_alarm(EXEC_ALARM_HOMING_FAIL_PULLOFF); }
|
|
// Homing failure condition: Limit switch not found during approach.
|
|
if (approach && (rt_exec & EXEC_CYCLE_STOP)) { system_set_exec_alarm(EXEC_ALARM_HOMING_FAIL_APPROACH); }
|
|
if (sys_rt_exec_alarm) {
|
|
mc_reset(); // Stop motors, if they are running.
|
|
protocol_execute_realtime();
|
|
return;
|
|
} else {
|
|
// Pull-off motion complete. Disable CYCLE_STOP from executing.
|
|
system_clear_exec_state_flag(EXEC_CYCLE_STOP);
|
|
break;
|
|
}
|
|
}
|
|
|
|
} while (STEP_MASK & axislock);
|
|
|
|
st_reset(); // Immediately force kill steppers and reset step segment buffer.
|
|
delay_ms(settings.homing_debounce_delay); // Delay to allow transient dynamics to dissipate.
|
|
|
|
// Reverse direction and reset homing rate for locate cycle(s).
|
|
approach = !approach;
|
|
|
|
// After first cycle, homing enters locating phase. Shorten search to pull-off distance.
|
|
if (approach) {
|
|
max_travel = settings.homing_pulloff*HOMING_AXIS_LOCATE_SCALAR;
|
|
homing_rate = settings.homing_feed_rate;
|
|
} else {
|
|
max_travel = settings.homing_pulloff;
|
|
homing_rate = settings.homing_seek_rate;
|
|
}
|
|
|
|
} while (n_cycle-- > 0);
|
|
|
|
// The active cycle axes should now be homed and machine limits have been located. By
|
|
// default, Grbl defines machine space as all negative, as do most CNCs. Since limit switches
|
|
// can be on either side of an axes, check and set axes machine zero appropriately. Also,
|
|
// set up pull-off maneuver from axes limit switches that have been homed. This provides
|
|
// some initial clearance off the switches and should also help prevent them from falsely
|
|
// triggering when hard limits are enabled or when more than one axes shares a limit pin.
|
|
int32_t set_axis_position;
|
|
// Set machine positions for homed limit switches. Don't update non-homed axes.
|
|
for (idx=0; idx<N_AXIS; idx++) {
|
|
// NOTE: settings.max_travel[] is stored as a negative value.
|
|
if (cycle_mask & bit(idx)) {
|
|
#ifdef HOMING_FORCE_SET_ORIGIN
|
|
set_axis_position = 0;
|
|
#else
|
|
if ( bit_istrue(settings.homing_dir_mask,bit(idx)) ) {
|
|
#ifdef HOMING_FORCE_POSITIVE_SPACE
|
|
set_axis_position = 0; //lround(settings.homing_pulloff*settings.steps_per_mm[idx]);
|
|
#else
|
|
set_axis_position = lround((settings.max_travel[idx]-settings.homing_pulloff)*settings.steps_per_mm[idx]);
|
|
#endif
|
|
} else {
|
|
#ifdef HOMING_FORCE_POSITIVE_SPACE
|
|
set_axis_position = lround(-settings.max_travel[idx]*settings.steps_per_mm[idx]);
|
|
#else
|
|
set_axis_position = lround(-settings.homing_pulloff*settings.steps_per_mm[idx]);
|
|
#endif
|
|
}
|
|
#endif
|
|
|
|
#ifdef COREXY
|
|
if (idx==X_AXIS) {
|
|
int32_t off_axis_position = system_convert_corexy_to_y_axis_steps(sys_position);
|
|
sys_position[A_MOTOR] = set_axis_position + off_axis_position;
|
|
sys_position[B_MOTOR] = set_axis_position - off_axis_position;
|
|
} else if (idx==Y_AXIS) {
|
|
int32_t off_axis_position = system_convert_corexy_to_x_axis_steps(sys_position);
|
|
sys_position[A_MOTOR] = off_axis_position + set_axis_position;
|
|
sys_position[B_MOTOR] = off_axis_position - set_axis_position;
|
|
} else {
|
|
sys_position[idx] = set_axis_position;
|
|
}
|
|
#else
|
|
sys_position[idx] = set_axis_position;
|
|
#endif
|
|
|
|
}
|
|
}
|
|
sys.step_control = STEP_CONTROL_NORMAL_OP; // Return step control to normal operation.
|
|
}
|
|
|
|
|
|
// Performs a soft limit check. Called from mc_line() only. Assumes the machine has been homed,
|
|
// the workspace volume is in all negative space, and the system is in normal operation.
|
|
// NOTE: Used by jogging to limit travel within soft-limit volume.
|
|
void limits_soft_check(float *target)
|
|
{
|
|
if (system_check_travel_limits(target)) {
|
|
sys.soft_limit = true;
|
|
// Force feed hold if cycle is active. All buffered blocks are guaranteed to be within
|
|
// workspace volume so just come to a controlled stop so position is not lost. When complete
|
|
// enter alarm mode.
|
|
if (sys.state == STATE_CYCLE) {
|
|
system_set_exec_state_flag(EXEC_FEED_HOLD);
|
|
do {
|
|
protocol_execute_realtime();
|
|
if (sys.abort) { return; }
|
|
} while ( sys.state != STATE_IDLE );
|
|
}
|
|
mc_reset(); // Issue system reset and ensure spindle and coolant are shutdown.
|
|
system_set_exec_alarm(EXEC_ALARM_SOFT_LIMIT); // Indicate soft limit critical event
|
|
protocol_execute_realtime(); // Execute to enter critical event loop and system abort
|
|
return;
|
|
}
|
|
}
|