50fbc6e297
WARNING: There are still some bugs to be worked out. Please use caution if you test this firmware. - Feed holds work much better, but there are still some failure conditions that need to be worked out. This is the being worked on currently and a fix is planned to be pushed next. - Homing cycle refactoring: Slight adjustment of the homing cycle to allow for limit pins to be shared by different axes, as long as the shared limit pins are not homed on the same cycle. Also, removed the LOCATE_CYCLE portion of the homing cycle configuration. It was redundant. - Limit pin sharing: (See above). To clear up one or two limit pins for other IO, limit pins can now be shared. For example, the Z-limit can be shared with either X or Y limit pins, because it’s on a separate homing cycle. Hard limit will still work exactly as before. - Spindle pin output fixed. The pins weren’t getting initialized correctly. - Fixed a cycle issue where streaming was working almost like a single block mode. This was caused by a problem with the spindle_run() and coolant_run() commands and issuing an unintended planner buffer sync. - Refactored the cycle_start, feed_hold, and other runtime routines into the runtime command module, where they should be handled here only. These were redundant. - Moved some function calls around into more appropriate source code modules. - Fixed the reporting of spindle state.
95 lines
3.3 KiB
C
95 lines
3.3 KiB
C
/*
|
|
main.c - An embedded CNC Controller with rs274/ngc (g-code) support
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2011-2014 Sungeun K. Jeon
|
|
Copyright (c) 2009-2011 Simen Svale Skogsrud
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include "system.h"
|
|
#include "serial.h"
|
|
#include "settings.h"
|
|
#include "protocol.h"
|
|
#include "gcode.h"
|
|
#include "planner.h"
|
|
#include "stepper.h"
|
|
#include "spindle_control.h"
|
|
#include "coolant_control.h"
|
|
#include "motion_control.h"
|
|
#include "limits.h"
|
|
#include "report.h"
|
|
|
|
|
|
// Declare system global variable structure
|
|
system_t sys;
|
|
|
|
|
|
int main(void)
|
|
{
|
|
// Initialize system upon power-up.
|
|
serial_init(); // Setup serial baud rate and interrupts
|
|
settings_init(); // Load grbl settings from EEPROM
|
|
stepper_init(); // Configure stepper pins and interrupt timers
|
|
system_init(); // Configure pinout pins and pin-change interrupt
|
|
|
|
memset(&sys, 0, sizeof(sys)); // Clear all system variables
|
|
sys.abort = true; // Set abort to complete initialization
|
|
sei(); // Enable interrupts
|
|
|
|
// Check for power-up and set system alarm if homing is enabled to force homing cycle
|
|
// by setting Grbl's alarm state. Alarm locks out all g-code commands, including the
|
|
// startup scripts, but allows access to settings and internal commands. Only a homing
|
|
// cycle '$H' or kill alarm locks '$X' will disable the alarm.
|
|
// NOTE: The startup script will run after successful completion of the homing cycle, but
|
|
// not after disabling the alarm locks. Prevents motion startup blocks from crashing into
|
|
// things uncontrollably. Very bad.
|
|
#ifdef HOMING_INIT_LOCK
|
|
if (bit_istrue(settings.flags,BITFLAG_HOMING_ENABLE)) { sys.state = STATE_ALARM; }
|
|
#endif
|
|
|
|
// Grbl initialization loop upon power-up or a system abort. For the latter, all processes
|
|
// will return to this loop to be cleanly re-initialized.
|
|
for(;;) {
|
|
|
|
// TODO: Separate configure task that require interrupts to be disabled, especially upon
|
|
// a system abort and ensuring any active interrupts are cleanly reset.
|
|
|
|
// Reset Grbl primary systems.
|
|
serial_reset_read_buffer(); // Clear serial read buffer
|
|
gc_init(); // Set g-code parser to default state
|
|
spindle_init();
|
|
coolant_init();
|
|
limits_init();
|
|
plan_reset(); // Clear block buffer and planner variables
|
|
st_reset(); // Clear stepper subsystem variables.
|
|
|
|
// Sync cleared gcode and planner positions to current system position.
|
|
plan_sync_position();
|
|
gc_sync_position();
|
|
|
|
// Reset system variables.
|
|
sys.abort = false;
|
|
sys.execute = 0;
|
|
if (bit_istrue(settings.flags,BITFLAG_AUTO_START)) { sys.auto_start = true; }
|
|
else { sys.auto_start = false; }
|
|
|
|
// Start Grbl main loop. Processes program inputs and executes them.
|
|
protocol_main_loop();
|
|
|
|
}
|
|
return 0; /* Never reached */
|
|
}
|