248 lines
7.3 KiB
C
248 lines
7.3 KiB
C
/*
|
|
stepper.c - stepper motor interface
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2009 Simen Svale Skogsrud
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/* The timer calculations of this module informed by the 'RepRap cartesian firmware' by Zack Smith
|
|
and Philipp Tiefenbacher. The circle buffer implementation gleaned from the wiring_serial library
|
|
by David A. Mellis */
|
|
|
|
#include "stepper.h"
|
|
#include "config.h"
|
|
#include "nuts_bolts.h"
|
|
#include <avr/interrupt.h>
|
|
|
|
#include "wiring_serial.h"
|
|
|
|
#define TICKS_PER_MICROSECOND (F_CPU/1000000)
|
|
#define STEP_BUFFER_SIZE 100
|
|
|
|
volatile uint8_t step_buffer[STEP_BUFFER_SIZE]; // A buffer for step instructions
|
|
volatile int step_buffer_head = 0;
|
|
volatile int step_buffer_tail = 0;
|
|
|
|
uint8_t stepper_mode = STEPPER_MODE_STOPPED;
|
|
uint8_t echo_steps = true;
|
|
|
|
// This timer interrupt is executed at the pace set with set_pace. It pops one instruction from
|
|
// the step_buffer, executes it. Then it starts timer2 in order to reset the motor port after
|
|
// five microseconds.
|
|
SIGNAL(SIG_OUTPUT_COMPARE1A)
|
|
{
|
|
if (step_buffer_head != step_buffer_tail) {
|
|
// Set the direction pins a nanosecond or two before you step the steppers
|
|
STEPPING_PORT = (STEPPING_PORT & ~DIRECTION_MASK) | (step_buffer[step_buffer_tail] & DIRECTION_MASK);
|
|
// Then pulse the stepping pins
|
|
STEPPING_PORT = (STEPPING_PORT & ~STEP_MASK) | step_buffer[step_buffer_tail];
|
|
// Reset and start timer 2 which will reset the motor port after 5 microsecond
|
|
TCNT2 = 0; // reset counter
|
|
OCR2A = 5*TICKS_PER_MICROSECOND; // set the time
|
|
TIMSK2 |= (1<<OCIE2A); // enable interrupt
|
|
// move the step buffer tail to the next instruction
|
|
step_buffer_tail = (step_buffer_tail + 1) % STEP_BUFFER_SIZE;
|
|
}
|
|
}
|
|
|
|
// This interrupt is set up by SIG_OUTPUT_COMPARE1A when it sets the motor port bits. It resets
|
|
// the motor port after a short period (5us) completing one step cycle.
|
|
SIGNAL(SIG_OUTPUT_COMPARE2A)
|
|
{
|
|
STEPPING_PORT = STEPPING_PORT & ~STEP_MASK; // reset stepping pins (leave the direction pins)
|
|
TIMSK2 &= ~(1<<OCIE2A); // disable this timer interrupt until next time
|
|
}
|
|
|
|
// Initialize and start the stepper motor subsystem
|
|
void st_init()
|
|
{
|
|
// Configure directions of interface pins
|
|
STEPPING_DDR |= STEPPING_MASK;
|
|
LIMIT_DDR &= ~(LIMIT_MASK);
|
|
STEPPERS_ENABLE_DDR |= 1<<STEPPERS_ENABLE_BIT;
|
|
|
|
// waveform generation = 0100 = CTC
|
|
TCCR1B &= ~(1<<WGM13);
|
|
TCCR1B |= (1<<WGM12);
|
|
TCCR1A &= ~(1<<WGM11);
|
|
TCCR1A &= ~(1<<WGM10);
|
|
|
|
// output mode = 00 (disconnected)
|
|
TCCR1A &= ~(3<<COM1A0);
|
|
TCCR1A &= ~(3<<COM1B0);
|
|
|
|
// Configure Timer 2
|
|
TCCR2A = 0; // Normal operation
|
|
TCCR2B = 1<<CS20; // Full speed, no prescaler
|
|
TIMSK2 = 0; // All interrupts disabled
|
|
|
|
sei();
|
|
|
|
// start off with a slow pace
|
|
st_set_pace(20000);
|
|
st_start();
|
|
}
|
|
|
|
void st_buffer_step(uint8_t motor_port_bits)
|
|
{
|
|
if (echo_steps) {
|
|
printByte('!'+motor_port_bits);
|
|
// printIntegerInBase(motor_port_bits,2);printByte('\r');printByte('\n');
|
|
}
|
|
|
|
int i = (step_buffer_head + 1) % STEP_BUFFER_SIZE;
|
|
|
|
// If the buffer is full: good! That means we are well ahead of the robot.
|
|
// Nap until there is room for more steps.
|
|
while(step_buffer_tail == i) { sleep_mode(); }
|
|
|
|
step_buffer[step_buffer_head] = motor_port_bits;
|
|
step_buffer_head = i;
|
|
}
|
|
|
|
// Block until all buffered steps are executed
|
|
void st_synchronize()
|
|
{
|
|
if (stepper_mode == STEPPER_MODE_RUNNING) {
|
|
while(step_buffer_tail != step_buffer_head) { sleep_mode(); }
|
|
} else {
|
|
st_flush();
|
|
}
|
|
}
|
|
|
|
// Cancel all pending steps
|
|
void st_flush()
|
|
{
|
|
cli();
|
|
step_buffer_tail = step_buffer_head;
|
|
sei();
|
|
}
|
|
|
|
// Start the stepper subsystem
|
|
void st_start()
|
|
{
|
|
// Enable timer interrupt
|
|
TIMSK1 |= (1<<OCIE1A);
|
|
STEPPERS_ENABLE_PORT |= 1<<STEPPERS_ENABLE_BIT;
|
|
stepper_mode = STEPPER_MODE_RUNNING;
|
|
}
|
|
|
|
// Execute all buffered steps, then stop the stepper subsystem
|
|
inline void st_stop()
|
|
{
|
|
st_synchronize();
|
|
TIMSK1 &= ~(1<<OCIE1A);
|
|
STEPPERS_ENABLE_PORT &= ~(1<<STEPPERS_ENABLE_BIT);
|
|
stepper_mode = STEPPER_MODE_STOPPED;
|
|
}
|
|
|
|
void st_set_pace(uint32_t microseconds)
|
|
{
|
|
printString("pace = ");
|
|
printInteger(microseconds);
|
|
printString("\n\r");
|
|
uint32_t ticks = microseconds*TICKS_PER_MICROSECOND;
|
|
uint16_t ceiling;
|
|
uint16_t prescaler;
|
|
if (ticks <= 0xffffL) {
|
|
ceiling = ticks;
|
|
prescaler = 0; // prescaler: 0
|
|
} else if (ticks <= 0x7ffffL) {
|
|
ceiling = ticks >> 3;
|
|
prescaler = 1; // prescaler: 8
|
|
} else if (ticks <= 0x3fffffL) {
|
|
ceiling = ticks >> 6;
|
|
prescaler = 2; // prescaler: 64
|
|
} else if (ticks <= 0xffffffL) {
|
|
ceiling = (ticks >> 8);
|
|
prescaler = 3; // prescaler: 256
|
|
} else if (ticks <= 0x3ffffffL) {
|
|
ceiling = (ticks >> 10);
|
|
prescaler = 4; // prescaler: 1024
|
|
} else {
|
|
// Okay, that was slower than we actually go. Just set the slowest speed
|
|
ceiling = 0xffff;
|
|
prescaler = 4;
|
|
}
|
|
// Set prescaler
|
|
TCCR1B = (TCCR1B & ~(0x07<<CS10)) | ((prescaler+1)<<CS10);
|
|
// Set ceiling
|
|
OCR1A = ceiling;
|
|
}
|
|
|
|
int check_limit_switches()
|
|
{
|
|
// Dual read as crude debounce
|
|
return((LIMIT_PORT & LIMIT_MASK) | (LIMIT_PORT & LIMIT_MASK));
|
|
}
|
|
|
|
int check_limit_switch(int axis)
|
|
{
|
|
uint8_t mask = 0;
|
|
switch (axis) {
|
|
case X_AXIS: mask = 1<<X_LIMIT_BIT; break;
|
|
case Y_AXIS: mask = 1<<Y_LIMIT_BIT; break;
|
|
case Z_AXIS: mask = 1<<Z_LIMIT_BIT; break;
|
|
}
|
|
return((LIMIT_PORT&mask) || (LIMIT_PORT&mask));
|
|
}
|
|
|
|
// void perform_go_home()
|
|
// {
|
|
// int axis;
|
|
// if(stepper_mode.home.phase == PHASE_HOME_RETURN) {
|
|
// // We are running all axes in reverse until all limit switches are tripped
|
|
// // Check all limit switches:
|
|
// for(axis=X_AXIS; axis <= Z_AXIS; axis++) {
|
|
// stepper_mode.home.away[axis] |= check_limit_switch(axis);
|
|
// }
|
|
// // Step steppers. First retract along Z-axis. Then X and Y.
|
|
// if(stepper_mode.home.away[Z_AXIS]) {
|
|
// step_axis(Z_AXIS);
|
|
// } else {
|
|
// // Check if all axes are home
|
|
// if(!(stepper_mode.home.away[X_AXIS] || stepper_mode.home.away[Y_AXIS])) {
|
|
// // All axes are home, prepare next phase: to nudge the tool carefully out of the limit switches
|
|
// memset(stepper_mode.home.direction, 1, sizeof(stepper_mode.home.direction)); // direction = [1,1,1]
|
|
// set_direction_bits(stepper_mode.home.direction);
|
|
// stepper_mode.home.phase == PHASE_HOME_NUDGE;
|
|
// return;
|
|
// }
|
|
// step_steppers(stepper_mode.home.away);
|
|
// }
|
|
// } else {
|
|
// for(axis=X_AXIS; axis <= Z_AXIS; axis++) {
|
|
// if(check_limit_switch(axis)) {
|
|
// step_axis(axis);
|
|
// return;
|
|
// }
|
|
// }
|
|
// // When this code is reached it means all axes are free of their limit-switches. Complete the cycle and rest:
|
|
// clear_vector(stepper_mode.position); // By definition this is location [0, 0, 0]
|
|
// stepper_mode.mode = MODE_AT_REST;
|
|
// }
|
|
// }
|
|
|
|
void st_go_home()
|
|
{
|
|
// Todo: Perform the homing cycle
|
|
}
|
|
|
|
void st_set_echo(int value)
|
|
{
|
|
echo_steps = value;
|
|
}
|