97 lines
3.1 KiB
C
97 lines
3.1 KiB
C
/*
|
|
spindle_control.c - spindle control methods
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2012-2014 Sungeun K. Jeon
|
|
Copyright (c) 2009-2011 Simen Svale Skogsrud
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include "system.h"
|
|
#include "spindle_control.h"
|
|
#include "protocol.h"
|
|
#include "gcode.h"
|
|
|
|
|
|
void spindle_init()
|
|
{
|
|
// On the Uno, spindle enable and PWM are shared. Other CPUs have seperate enable pin.
|
|
#ifdef VARIABLE_SPINDLE
|
|
SPINDLE_PWM_DDR |= (1<<SPINDLE_PWM_BIT); // Configure as PWM output pin.
|
|
#ifndef CPU_MAP_ATMEGA328P
|
|
SPINDLE_ENABLE_DDR |= (1<<SPINDLE_ENABLE_BIT); // Configure as output pin.
|
|
#endif
|
|
#else
|
|
SPINDLE_ENABLE_DDR |= (1<<SPINDLE_ENABLE_BIT); // Configure as output pin.
|
|
#endif
|
|
SPINDLE_DIRECTION_DDR |= (1<<SPINDLE_DIRECTION_BIT); // Configure as output pin.
|
|
spindle_stop();
|
|
}
|
|
|
|
|
|
void spindle_stop()
|
|
{
|
|
// On the Uno, spindle enable and PWM are shared. Other CPUs have seperate enable pin.
|
|
#ifdef VARIABLE_SPINDLE
|
|
TCCRA_REGISTER &= ~(1<<COMB_BIT); // Disable PWM. Output voltage is zero.
|
|
#ifndef CPU_MAP_ATMEGA328P
|
|
SPINDLE_ENABLE_PORT &= ~(1<<SPINDLE_ENABLE_BIT); // Set pin to low.
|
|
#endif
|
|
#else
|
|
SPINDLE_ENABLE_PORT &= ~(1<<SPINDLE_ENABLE_BIT); // Set pin to low.
|
|
#endif
|
|
}
|
|
|
|
|
|
void spindle_run(uint8_t direction, float rpm)
|
|
{
|
|
if (sys.state == STATE_CHECK_MODE) { return; }
|
|
|
|
// Empty planner buffer to ensure spindle is set when programmed.
|
|
protocol_auto_cycle_start(); //temp fix for M3 lockup
|
|
protocol_buffer_synchronize();
|
|
|
|
// Halt or set spindle direction and rpm.
|
|
if (direction == SPINDLE_DISABLE) {
|
|
|
|
spindle_stop();
|
|
|
|
} else {
|
|
|
|
if (direction == SPINDLE_ENABLE_CW) {
|
|
SPINDLE_DIRECTION_PORT &= ~(1<<SPINDLE_DIRECTION_BIT);
|
|
} else {
|
|
SPINDLE_DIRECTION_PORT |= (1<<SPINDLE_DIRECTION_BIT);
|
|
}
|
|
|
|
#ifdef VARIABLE_SPINDLE
|
|
#define SPINDLE_RPM_RANGE (SPINDLE_MAX_RPM-SPINDLE_MIN_RPM)
|
|
TCCRA_REGISTER = (1<<COMB_BIT) | (1<<WAVE1_REGISTER) | (1<<WAVE0_REGISTER);
|
|
TCCRB_REGISTER = (TCCRB_REGISTER & 0b11111000) | 0x02; // set to 1/8 Prescaler
|
|
rpm -= SPINDLE_MIN_RPM;
|
|
if ( rpm > SPINDLE_RPM_RANGE ) { rpm = SPINDLE_RPM_RANGE; } // Prevent uint8 overflow
|
|
uint8_t current_pwm = floor( rpm*(255.0/SPINDLE_RPM_RANGE) + 0.5);
|
|
OCR_REGISTER = current_pwm;
|
|
|
|
#ifndef CPU_MAP_ATMEGA328P // On the Uno, spindle enable and PWM are shared.
|
|
SPINDLE_ENABLE_PORT |= (1<<SPINDLE_ENABLE_BIT);
|
|
#endif
|
|
#else
|
|
SPINDLE_ENABLE_PORT |= (1<<SPINDLE_ENABLE_BIT);
|
|
#endif
|
|
|
|
}
|
|
}
|