ManuelW/grbl-LPC-CoreXY
1
0
Fork 0
Code Issues Pull Requests Releases 1 Wiki Activity
76ab1b6a42
grbl-LPC-CoreXY/gcode.c
Sonny Jeon 76ab1b6a42 G38.2 probe feature rough draft installed. Working but needs testing. 
- G38.2 straight probe now supported. Rough draft. May be tweaked more
as testing ramps up.

- G38.2 requires at least one axis word. Multiple axis words work too.
When commanded, the probe cycle will move at the last ‘F’ feed rate
specified in a straight line.

- During a probe cycle: If the probe pin goes low (normal high), Grbl
will record that immediate position and engage a feed hold. Meaning
that the CNC machine will move a little past the probe switch point, so
keep federates low to stop sooner. Once stopped, Grbl will issue a move
to go back to the recorded probe trigger point.

- During a probe cycle: If the probe switch does not engage by the time
the machine has traveled to its target coordinates, Grbl will issue an
ALARM and the user will be forced to reset Grbl. (Currently G38.3 probe
without error isn’t supported, but would be easy to implement later.)

- After a successful probe, Grbl will send a feedback message
containing the recorded probe coordinates in the machine coordinate
system. This is as the g-code standard on probe parameters specifies.

- The recorded probe parameters are retained in Grbl memory and can be
viewed with the ‘$#’ print parameters command. Upon a power-cycle, not
a soft-reset, Grbl will re-zero these values.

- Moved ‘$#’ command to require IDLE or ALARM mode, because it accesses
EEPROM to fetch the coordinate system offsets.

- Updated the Grbl version to v0.9d.

- The probe cycle is subject to change upon testing or user-feedback.
2014-02-28 22:03:26 -07:00

665 lines
29 KiB
C
Raw Blame History

/*
gcode.c - rs274/ngc parser.
Part of Grbl
Copyright (c) 2011-2014 Sungeun K. Jeon
Copyright (c) 2009-2011 Simen Svale Skogsrud
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
/* This code is inspired by the Arduino GCode Interpreter by Mike Ellery and the NIST RS274/NGC Interpreter
by Kramer, Proctor and Messina. */
#include "system.h"
#include "settings.h"
#include "protocol.h"
#include "gcode.h"
#include "motion_control.h"
#include "spindle_control.h"
#include "coolant_control.h"
#include "report.h"
// Declare gc extern struct
parser_state_t gc;
#define FAIL(status) gc.status_code = status;
static uint8_t next_statement(char *letter, float *float_ptr, char *line, uint8_t *char_counter);
static void gc_convert_arc_radius_mode(float *target) __attribute__((noinline));
static void select_plane(uint8_t axis_0, uint8_t axis_1, uint8_t axis_2)
{
gc.plane_axis_0 = axis_0;
gc.plane_axis_1 = axis_1;
gc.plane_axis_2 = axis_2;
}
void gc_init()
{
memset(&gc, 0, sizeof(gc));
gc.feed_rate = settings.default_feed_rate;
select_plane(X_AXIS, Y_AXIS, Z_AXIS);
gc.absolute_mode = true;
// Load default G54 coordinate system.
if (!(settings_read_coord_data(gc.coord_select,gc.coord_system))) {
report_status_message(STATUS_SETTING_READ_FAIL);
}
}
// Sets g-code parser position in mm. Input in steps. Called by the system abort and hard
// limit pull-off routines.
void gc_sync_position(int32_t x, int32_t y, int32_t z)
{
uint8_t i;
for (i=0; i<N_AXIS; i++) {
gc.position[i] = sys.position[i]/settings.steps_per_mm[i];
}
}
static float to_millimeters(float value)
{
return(gc.inches_mode ? (value * MM_PER_INCH) : value);
}
// Executes one line of 0-terminated G-Code. The line is assumed to contain only uppercase
// characters and signed floating point values (no whitespace). Comments and block delete
// characters have been removed. In this function, all units and positions are converted and
// exported to grbl's internal functions in terms of (mm, mm/min) and absolute machine
// coordinates, respectively.
uint8_t gc_execute_line(char *line)
{
uint8_t char_counter = 0;
char letter;
float value;
int int_value;
uint16_t modal_group_words = 0; // Bitflag variable to track and check modal group words in block
uint8_t axis_words = 0; // Bitflag to track which XYZ(ABC) parameters exist in block
float inverse_feed_rate = -1; // negative inverse_feed_rate means no inverse_feed_rate specified
uint8_t absolute_override = false; // true(1) = absolute motion for this block only {G53}
uint8_t non_modal_action = NON_MODAL_NONE; // Tracks the actions of modal group 0 (non-modal)
float target[N_AXIS];
clear_vector(target); // XYZ(ABC) axes parameters.
#ifdef USE_LINE_NUMBERS
int32_t line_number = 0;
#endif
gc.arc_radius = 0;
clear_vector(gc.arc_offset); // IJK Arc offsets are incremental. Value of zero indicates no change.
gc.status_code = STATUS_OK;
/* Pass 1: Commands and set all modes. Check for modal group violations.
NOTE: Modal group numbers are defined in Table 4 of NIST RS274-NGC v3, pg.20 */
uint8_t group_number = MODAL_GROUP_NONE;
while(next_statement(&letter, &value, line, &char_counter)) {
int_value = trunc(value);
switch(letter) {
case 'G':
// Set modal group values
switch(int_value) {
case 4: case 10: case 28: case 30: case 53: case 92: group_number = MODAL_GROUP_0; break;
case 0: case 1: case 2: case 3: case 38: case 80: group_number = MODAL_GROUP_1; break;
case 17: case 18: case 19: group_number = MODAL_GROUP_2; break;
case 90: case 91: group_number = MODAL_GROUP_3; break;
case 93: case 94: group_number = MODAL_GROUP_5; break;
case 20: case 21: group_number = MODAL_GROUP_6; break;
case 54: case 55: case 56: case 57: case 58: case 59: group_number = MODAL_GROUP_12; break;
}
// Set 'G' commands
switch(int_value) {
case 0: gc.motion_mode = MOTION_MODE_SEEK; break;
case 1: gc.motion_mode = MOTION_MODE_LINEAR; break;
case 2: gc.motion_mode = MOTION_MODE_CW_ARC; break;
case 3: gc.motion_mode = MOTION_MODE_CCW_ARC; break;
case 4: non_modal_action = NON_MODAL_DWELL; break;
case 10: non_modal_action = NON_MODAL_SET_COORDINATE_DATA; break;
case 17: select_plane(X_AXIS, Y_AXIS, Z_AXIS); break;
case 18: select_plane(Z_AXIS, X_AXIS, Y_AXIS); break;
case 19: select_plane(Y_AXIS, Z_AXIS, X_AXIS); break;
case 20: gc.inches_mode = true; break;
case 21: gc.inches_mode = false; break;
case 28: case 30:
int_value = trunc(10*value); // Multiply by 10 to pick up Gxx.1
switch(int_value) {
case 280: non_modal_action = NON_MODAL_GO_HOME_0; break;
case 281: non_modal_action = NON_MODAL_SET_HOME_0; break;
case 300: non_modal_action = NON_MODAL_GO_HOME_1; break;
case 301: non_modal_action = NON_MODAL_SET_HOME_1; break;
default: FAIL(STATUS_UNSUPPORTED_STATEMENT);
}
break;
case 38:
int_value = trunc(10*value); // Multiply by 10 to pick up Gxx.1
switch(int_value) {
case 382: gc.motion_mode = MOTION_MODE_PROBE; break;
// case 383: gc.motion_mode = MOTION_MODE_PROBE_NO_ERROR; break; // Not supported.
// case 384: // Not supported.
// case 385: // Not supported.
default: FAIL(STATUS_UNSUPPORTED_STATEMENT);
}
break;
case 53: absolute_override = true; break;
case 54: case 55: case 56: case 57: case 58: case 59:
gc.coord_select = int_value-54;
break;
case 80: gc.motion_mode = MOTION_MODE_CANCEL; break;
case 90: gc.absolute_mode = true; break;
case 91: gc.absolute_mode = false; break;
case 92:
int_value = trunc(10*value); // Multiply by 10 to pick up G92.1
switch(int_value) {
case 920: non_modal_action = NON_MODAL_SET_COORDINATE_OFFSET; break;
case 921: non_modal_action = NON_MODAL_RESET_COORDINATE_OFFSET; break;
default: FAIL(STATUS_UNSUPPORTED_STATEMENT);
}
break;
case 93: gc.inverse_feed_rate_mode = true; break;
case 94: gc.inverse_feed_rate_mode = false; break;
default: FAIL(STATUS_UNSUPPORTED_STATEMENT);
}
break;
case 'M':
// Set modal group values
switch(int_value) {
case 0: case 1: case 2: case 30: group_number = MODAL_GROUP_4; break;
case 3: case 4: case 5: group_number = MODAL_GROUP_7; break;
case 7: case 8: case 9: group_number = MODAL_GROUP_8; break;
}
// Set 'M' commands
switch(int_value) {
case 0: gc.program_flow = PROGRAM_FLOW_PAUSED; break; // Program pause
case 1: break; // Optional stop not supported. Ignore.
case 2: case 30: gc.program_flow = PROGRAM_FLOW_COMPLETED; break; // Program end and reset
case 3: gc.spindle_direction = SPINDLE_ENABLE_CW; break;
case 4: gc.spindle_direction = SPINDLE_ENABLE_CCW; break;
case 5: gc.spindle_direction = SPINDLE_DISABLE; break;
#ifdef ENABLE_M7
case 7: gc.coolant_mode = COOLANT_MIST_ENABLE; break;
#endif
case 8: gc.coolant_mode = COOLANT_FLOOD_ENABLE; break;
case 9: gc.coolant_mode = COOLANT_DISABLE; break;
default: FAIL(STATUS_UNSUPPORTED_STATEMENT);
}
break;
}
// Check for modal group multiple command violations in the current block
if (group_number) {
if ( bit_istrue(modal_group_words,bit(group_number)) ) {
FAIL(STATUS_MODAL_GROUP_VIOLATION);
} else {
bit_true(modal_group_words,bit(group_number));
}
group_number = MODAL_GROUP_NONE; // Reset for next command.
}
}
// If there were any errors parsing this line, we will return right away with the bad news
if (gc.status_code) { return(gc.status_code); }
/* Pass 2: Parameters. All units converted according to current block commands. Position
parameters are converted and flagged to indicate a change. These can have multiple connotations
for different commands. Each will be converted to their proper value upon execution.
NOTE: Grbl unconventionally pre-converts these parameter values based on the block G and M
commands. This is set out of the order of execution defined by NIST only for code efficiency/size
purposes, but should not affect proper g-code execution. */
float p = 0;
uint8_t l = 0;
char_counter = 0;
while(next_statement(&letter, &value, line, &char_counter)) {
switch(letter) {
case 'G': case 'M': break; // Ignore command statements and line numbers
case 'F':
if (value <= 0) { FAIL(STATUS_INVALID_STATEMENT); } // Must be greater than zero
if (gc.inverse_feed_rate_mode) {
inverse_feed_rate = to_millimeters(value); // seconds per motion for this motion only
} else {
gc.feed_rate = to_millimeters(value); // millimeters per minute
}
break;
case 'I': case 'J': case 'K': gc.arc_offset[letter-'I'] = to_millimeters(value); break;
case 'L': l = trunc(value); break;
case 'N':
#ifdef USE_LINE_NUMBERS
line_number = trunc(value);
#endif
break;
case 'P': p = value; break;
case 'R': gc.arc_radius = to_millimeters(value); break;
case 'S':
if (value < 0) { FAIL(STATUS_INVALID_STATEMENT); } // Cannot be negative
gc.spindle_speed = value;
break;
case 'T':
if (value < 0) { FAIL(STATUS_INVALID_STATEMENT); } // Cannot be negative
gc.tool = trunc(value);
break;
case 'X': target[X_AXIS] = to_millimeters(value); bit_true(axis_words,bit(X_AXIS)); break;
case 'Y': target[Y_AXIS] = to_millimeters(value); bit_true(axis_words,bit(Y_AXIS)); break;
case 'Z': target[Z_AXIS] = to_millimeters(value); bit_true(axis_words,bit(Z_AXIS)); break;
default: FAIL(STATUS_UNSUPPORTED_STATEMENT);
}
}
// If there were any errors parsing this line, we will return right away with the bad news
if (gc.status_code) { return(gc.status_code); }
// Initialize axis index
uint8_t idx;
/* Execute Commands: Perform by order of execution defined in NIST RS274-NGC.v3, Table 8, pg.41. */
// ([F]: Set feed rate.)
if (sys.state != STATE_CHECK_MODE) {
// ([M6]: Tool change should be executed here.)
// [M3,M4,M5]: Update spindle state
if (bit_istrue(modal_group_words,bit(MODAL_GROUP_7))) {
spindle_run(gc.spindle_direction, gc.spindle_speed);
}
// [*M7,M8,M9]: Update coolant state
if (bit_istrue(modal_group_words,bit(MODAL_GROUP_8))) {
coolant_run(gc.coolant_mode);
}
}
// [G54,G55,...,G59]: Coordinate system selection
if ( bit_istrue(modal_group_words,bit(MODAL_GROUP_12)) ) { // Check if called in block
float coord_data[N_AXIS];
if (!(settings_read_coord_data(gc.coord_select,coord_data))) { return(STATUS_SETTING_READ_FAIL); }
memcpy(gc.coord_system,coord_data,sizeof(coord_data));
}
// [G4,G10,G28,G30,G92,G92.1]: Perform dwell, set coordinate system data, homing, or set axis offsets.
// NOTE: These commands are in the same modal group, hence are mutually exclusive. G53 is in this
// modal group and do not effect these actions.
switch (non_modal_action) {
case NON_MODAL_DWELL:
if (p < 0) { // Time cannot be negative.
FAIL(STATUS_INVALID_STATEMENT);
} else {
// Ignore dwell in check gcode modes
if (sys.state != STATE_CHECK_MODE) { mc_dwell(p); }
}
break;
case NON_MODAL_SET_COORDINATE_DATA:
int_value = trunc(p); // Convert p value to int.
if ((l != 2 && l != 20) || (int_value < 0 || int_value > N_COORDINATE_SYSTEM)) { // L2 and L20. P1=G54, P2=G55, ...
FAIL(STATUS_UNSUPPORTED_STATEMENT);
} else if (!axis_words && l==2) { // No axis words.
FAIL(STATUS_INVALID_STATEMENT);
} else {
if (int_value > 0) { int_value--; } // Adjust P1-P6 index to EEPROM coordinate data indexing.
else { int_value = gc.coord_select; } // Index P0 as the active coordinate system
float coord_data[N_AXIS];
if (!settings_read_coord_data(int_value,coord_data)) { return(STATUS_SETTING_READ_FAIL); }
// Update axes defined only in block. Always in machine coordinates. Can change non-active system.
for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used.
if (bit_istrue(axis_words,bit(idx)) ) {
if (l == 20) {
coord_data[idx] = gc.position[idx]-target[idx]; // L20: Update axis current position to target
} else {
coord_data[idx] = target[idx]; // L2: Update coordinate system axis
}
}
}
settings_write_coord_data(int_value,coord_data);
// Update system coordinate system if currently active.
if (gc.coord_select == int_value) { memcpy(gc.coord_system,coord_data,sizeof(coord_data)); }
}
axis_words = 0; // Axis words used. Lock out from motion modes by clearing flags.
break;
case NON_MODAL_GO_HOME_0: case NON_MODAL_GO_HOME_1:
// Move to intermediate position before going home. Obeys current coordinate system and offsets
// and absolute and incremental modes.
if (axis_words) {
// Apply absolute mode coordinate offsets or incremental mode offsets.
for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used.
if ( bit_istrue(axis_words,bit(idx)) ) {
if (gc.absolute_mode) {
target[idx] += gc.coord_system[idx] + gc.coord_offset[idx];
} else {
target[idx] += gc.position[idx];
}
} else {
target[idx] = gc.position[idx];
}
}
#ifdef USE_LINE_NUMBERS
mc_line(target, -1.0, false, line_number);
#else
mc_line(target, -1.0, false);
#endif
}
// Retreive G28/30 go-home position data (in machine coordinates) from EEPROM
float coord_data[N_AXIS];
if (non_modal_action == NON_MODAL_GO_HOME_0) {
if (!settings_read_coord_data(SETTING_INDEX_G28,coord_data)) { return(STATUS_SETTING_READ_FAIL); }
} else {
if (!settings_read_coord_data(SETTING_INDEX_G30,coord_data)) { return(STATUS_SETTING_READ_FAIL); }
}
#ifdef USE_LINE_NUMBERS
mc_line(coord_data, -1.0, false, line_number);
#else
mc_line(coord_data, -1.0, false);
#endif
memcpy(gc.position, coord_data, sizeof(coord_data)); // gc.position[] = coord_data[];
axis_words = 0; // Axis words used. Lock out from motion modes by clearing flags.
break;
case NON_MODAL_SET_HOME_0: case NON_MODAL_SET_HOME_1:
if (non_modal_action == NON_MODAL_SET_HOME_0) {
settings_write_coord_data(SETTING_INDEX_G28,gc.position);
} else {
settings_write_coord_data(SETTING_INDEX_G30,gc.position);
}
break;
case NON_MODAL_SET_COORDINATE_OFFSET:
if (!axis_words) { // No axis words
FAIL(STATUS_INVALID_STATEMENT);
} else {
// Update axes defined only in block. Offsets current system to defined value. Does not update when
// active coordinate system is selected, but is still active unless G92.1 disables it.
for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used.
if (bit_istrue(axis_words,bit(idx)) ) {
gc.coord_offset[idx] = gc.position[idx]-gc.coord_system[idx]-target[idx];
}
}
}
axis_words = 0; // Axis words used. Lock out from motion modes by clearing flags.
break;
case NON_MODAL_RESET_COORDINATE_OFFSET:
clear_vector(gc.coord_offset); // Disable G92 offsets by zeroing offset vector.
break;
}
// [G0,G1,G2,G3,G80]: Perform motion modes.
// NOTE: Commands G10,G28,G30,G92 lock out and prevent axis words from use in motion modes.
// Enter motion modes only if there are axis words or a motion mode command word in the block.
if ( bit_istrue(modal_group_words,bit(MODAL_GROUP_1)) || axis_words ) {
// G1,G2,G3 require F word in inverse time mode.
if ( gc.inverse_feed_rate_mode ) {
if (inverse_feed_rate < 0 && gc.motion_mode != MOTION_MODE_CANCEL) {
FAIL(STATUS_INVALID_STATEMENT);
}
}
// Absolute override G53 only valid with G0 and G1 active.
if ( absolute_override && !(gc.motion_mode == MOTION_MODE_SEEK || gc.motion_mode == MOTION_MODE_LINEAR)) {
FAIL(STATUS_INVALID_STATEMENT);
}
// Report any errors.
if (gc.status_code) { return(gc.status_code); }
// Convert all target position data to machine coordinates for executing motion. Apply
// absolute mode coordinate offsets or incremental mode offsets.
// NOTE: Tool offsets may be appended to these conversions when/if this feature is added.
for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used to save flash space.
if ( bit_istrue(axis_words,bit(idx)) ) {
if (!absolute_override) { // Do not update target in absolute override mode
if (gc.absolute_mode) {
target[idx] += gc.coord_system[idx] + gc.coord_offset[idx]; // Absolute mode
} else {
target[idx] += gc.position[idx]; // Incremental mode
}
}
} else {
target[idx] = gc.position[idx]; // No axis word in block. Keep same axis position.
}
}
switch (gc.motion_mode) {
case MOTION_MODE_CANCEL:
if (axis_words) { FAIL(STATUS_INVALID_STATEMENT); } // No axis words allowed while active.
break;
case MOTION_MODE_SEEK:
if (!axis_words) { FAIL(STATUS_INVALID_STATEMENT);}
else {
#ifdef USE_LINE_NUMBERS
mc_line(target, -1.0, false, line_number);
#else
mc_line(target, -1.0, false);
#endif
}
break;
case MOTION_MODE_LINEAR:
// TODO: Inverse time requires F-word with each statement. Need to do a check. Also need
// to check for initial F-word upon startup. Maybe just set to zero upon initialization
// and after an inverse time move and then check for non-zero feed rate each time. This
// should be efficient and effective.
if (!axis_words) { FAIL(STATUS_INVALID_STATEMENT);}
else {
#ifdef USE_LINE_NUMBERS
mc_line(target, (gc.inverse_feed_rate_mode) ? inverse_feed_rate : gc.feed_rate, gc.inverse_feed_rate_mode, line_number);
#else
mc_line(target, (gc.inverse_feed_rate_mode) ? inverse_feed_rate : gc.feed_rate, gc.inverse_feed_rate_mode);
#endif
}
break;
case MOTION_MODE_CW_ARC: case MOTION_MODE_CCW_ARC:
// Check if at least one of the axes of the selected plane has been specified. If in center
// format arc mode, also check for at least one of the IJK axes of the selected plane was sent.
if ( !( bit_false(axis_words,bit(gc.plane_axis_2)) ) ||
( !gc.arc_radius && !gc.arc_offset[gc.plane_axis_0] && !gc.arc_offset[gc.plane_axis_1] ) ) {
FAIL(STATUS_INVALID_STATEMENT);
} else {
if (gc.arc_radius != 0) { // Arc Radius Mode
// Compute arc radius and offsets
gc_convert_arc_radius_mode(target);
if (gc.status_code) { return(gc.status_code); }
} else { // Arc Center Format Offset Mode
gc.arc_radius = hypot(gc.arc_offset[gc.plane_axis_0], gc.arc_offset[gc.plane_axis_1]); // Compute arc radius for mc_arc
}
// Set clockwise/counter-clockwise sign for mc_arc computations
uint8_t isclockwise = false;
if (gc.motion_mode == MOTION_MODE_CW_ARC) { isclockwise = true; }
// Trace the arc
#ifdef USE_LINE_NUMBERS
mc_arc(gc.position, target, gc.arc_offset, gc.plane_axis_0, gc.plane_axis_1, gc.plane_axis_2,
(gc.inverse_feed_rate_mode) ? inverse_feed_rate : gc.feed_rate, gc.inverse_feed_rate_mode,
gc.arc_radius, isclockwise, line_number);
#else
mc_arc(gc.position, target, gc.arc_offset, gc.plane_axis_0, gc.plane_axis_1, gc.plane_axis_2,
(gc.inverse_feed_rate_mode) ? inverse_feed_rate : gc.feed_rate, gc.inverse_feed_rate_mode,
gc.arc_radius, isclockwise);
#endif
}
break;
case MOTION_MODE_PROBE:
if (!axis_words) { FAIL(STATUS_INVALID_STATEMENT); }
else {
#ifdef USE_LINE_NUMBERS
mc_probe_cycle(target, (gc.inverse_feed_rate_mode) ? inverse_feed_rate : gc.feed_rate, gc.inverse_feed_rate_mode, line_number);
#else
mc_probe_cycle(target, (gc.inverse_feed_rate_mode) ? inverse_feed_rate : gc.feed_rate, gc.inverse_feed_rate_mode);
#endif
}
break;
}
// Report any errors.
if (gc.status_code) { return(gc.status_code); }
// As far as the parser is concerned, the position is now == target. In reality the
// motion control system might still be processing the action and the real tool position
// in any intermediate location.
memcpy(gc.position, target, sizeof(target)); // gc.position[] = target[];
}
// M0,M1,M2,M30: Perform non-running program flow actions. During a program pause, the buffer may
// refill and can only be resumed by the cycle start run-time command.
if (gc.program_flow) {
protocol_buffer_synchronize(); // Finish all remaining buffered motions. Program paused when complete.
sys.auto_start = false; // Disable auto cycle start. Forces pause until cycle start issued.
// If complete, reset to reload defaults (G92.2,G54,G17,G90,G94,M48,G40,M5,M9). Otherwise,
// re-enable program flow after pause complete, where cycle start will resume the program.
if (gc.program_flow == PROGRAM_FLOW_COMPLETED) { mc_reset(); }
else { gc.program_flow = PROGRAM_FLOW_RUNNING; }
}
return(gc.status_code);
}
// Parses the next statement and leaves the counter on the first character following
// the statement. Returns 1 if there was a statements, 0 if end of string was reached
// or there was an error (check state.status_code).
static uint8_t next_statement(char *letter, float *float_ptr, char *line, uint8_t *char_counter)
{
if (line[*char_counter] == 0) {
return(0); // No more statements
}
*letter = line[*char_counter];
if((*letter < 'A') || (*letter > 'Z')) {
FAIL(STATUS_EXPECTED_COMMAND_LETTER);
return(0);
}
(*char_counter)++;
if (!read_float(line, char_counter, float_ptr)) {
FAIL(STATUS_BAD_NUMBER_FORMAT);
return(0);
};
return(1);
}
static void gc_convert_arc_radius_mode(float *target)
{
/* We need to calculate the center of the circle that has the designated radius and passes
through both the current position and the target position. This method calculates the following
set of equations where [x,y] is the vector from current to target position, d == magnitude of
that vector, h == hypotenuse of the triangle formed by the radius of the circle, the distance to
the center of the travel vector. A vector perpendicular to the travel vector [-y,x] is scaled to the
length of h [-y/d*h, x/d*h] and added to the center of the travel vector [x/2,y/2] to form the new point
[i,j] at [x/2-y/d*h, y/2+x/d*h] which will be the center of our arc.
d^2 == x^2 + y^2
h^2 == r^2 - (d/2)^2
i == x/2 - y/d*h
j == y/2 + x/d*h
O <- [i,j]
- |
r - |
- |
- | h
- |
[0,0] -> C -----------------+--------------- T <- [x,y]
| <------ d/2 ---->|
C - Current position
T - Target position
O - center of circle that pass through both C and T
d - distance from C to T
r - designated radius
h - distance from center of CT to O
Expanding the equations:
d -> sqrt(x^2 + y^2)
h -> sqrt(4 * r^2 - x^2 - y^2)/2
i -> (x - (y * sqrt(4 * r^2 - x^2 - y^2)) / sqrt(x^2 + y^2)) / 2
j -> (y + (x * sqrt(4 * r^2 - x^2 - y^2)) / sqrt(x^2 + y^2)) / 2
Which can be written:
i -> (x - (y * sqrt(4 * r^2 - x^2 - y^2))/sqrt(x^2 + y^2))/2
j -> (y + (x * sqrt(4 * r^2 - x^2 - y^2))/sqrt(x^2 + y^2))/2
Which we for size and speed reasons optimize to:
h_x2_div_d = sqrt(4 * r^2 - x^2 - y^2)/sqrt(x^2 + y^2)
i = (x - (y * h_x2_div_d))/2
j = (y + (x * h_x2_div_d))/2 */
// Calculate the change in position along each selected axis
float x = target[gc.plane_axis_0]-gc.position[gc.plane_axis_0];
float y = target[gc.plane_axis_1]-gc.position[gc.plane_axis_1];
clear_vector(gc.arc_offset);
// First, use h_x2_div_d to compute 4*h^2 to check if it is negative or r is smaller
// than d. If so, the sqrt of a negative number is complex and error out.
float h_x2_div_d = 4 * gc.arc_radius*gc.arc_radius - x*x - y*y;
if (h_x2_div_d < 0) { FAIL(STATUS_ARC_RADIUS_ERROR); return; }
// Finish computing h_x2_div_d.
h_x2_div_d = -sqrt(h_x2_div_d)/hypot(x,y); // == -(h * 2 / d)
// Invert the sign of h_x2_div_d if the circle is counter clockwise (see sketch below)
if (gc.motion_mode == MOTION_MODE_CCW_ARC) { h_x2_div_d = -h_x2_div_d; }
/* The counter clockwise circle lies to the left of the target direction. When offset is positive,
the left hand circle will be generated - when it is negative the right hand circle is generated.
T <-- Target position
^
Clockwise circles with this center | Clockwise circles with this center will have
will have > 180 deg of angular travel | < 180 deg of angular travel, which is a good thing!
\ | /
center of arc when h_x2_div_d is positive -> x <----- | -----> x <- center of arc when h_x2_div_d is negative
|
|
C <-- Current position */
// Negative R is g-code-alese for "I want a circle with more than 180 degrees of travel" (go figure!),
// even though it is advised against ever generating such circles in a single line of g-code. By
// inverting the sign of h_x2_div_d the center of the circles is placed on the opposite side of the line of
// travel and thus we get the unadvisably long arcs as prescribed.
if (gc.arc_radius < 0) {
h_x2_div_d = -h_x2_div_d;
gc.arc_radius = -gc.arc_radius; // Finished with r. Set to positive for mc_arc
}
// Complete the operation by calculating the actual center of the arc
gc.arc_offset[gc.plane_axis_0] = 0.5*(x-(y*h_x2_div_d));
gc.arc_offset[gc.plane_axis_1] = 0.5*(y+(x*h_x2_div_d));
}
/*
Not supported:
- Canned cycles
- Tool radius compensation
- A,B,C-axes
- Evaluation of expressions
- Variables
- Probing
- Override control (TBD)
- Tool changes
- Switches
(*) Indicates optional parameter, enabled through config.h and re-compile
group 0 = {G92.2, G92.3} (Non modal: Cancel and re-enable G92 offsets)
group 1 = {G38.2, G81 - G89} (Motion modes: straight probe, canned cycles)
group 4 = {M1} (Optional stop, ignored)
group 6 = {M6} (Tool change)
group 8 = {*M7} enable mist coolant
group 9 = {M48, M49} enable/disable feed and speed override switches
group 13 = {G61, G61.1, G64} path control mode
*/
Reference in New Issue View Git Blame Copy Permalink