144 lines
5.4 KiB
C
144 lines
5.4 KiB
C
/*
|
|
settings.h - eeprom configuration handling
|
|
Part of Grbl v0.9
|
|
|
|
Copyright (c) 2012-2014 Sungeun K. Jeon
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
/*
|
|
This file is based on work from Grbl v0.8, distributed under the
|
|
terms of the MIT-license. See COPYING for more details.
|
|
Copyright (c) 2009-2011 Simen Svale Skogsrud
|
|
Copyright (c) 2011-2012 Sungeun K. Jeon
|
|
*/
|
|
|
|
#ifndef settings_h
|
|
#define settings_h
|
|
|
|
|
|
#define GRBL_VERSION "0.9g"
|
|
#define GRBL_VERSION_BUILD "20140822"
|
|
|
|
// Version of the EEPROM data. Will be used to migrate existing data from older versions of Grbl
|
|
// when firmware is upgraded. Always stored in byte 0 of eeprom
|
|
#define SETTINGS_VERSION 9 // NOTE: Check settings_reset() when moving to next version.
|
|
|
|
// Define bit flag masks for the boolean settings in settings.flag.
|
|
#define BITFLAG_REPORT_INCHES bit(0)
|
|
#define BITFLAG_AUTO_START bit(1)
|
|
#define BITFLAG_INVERT_ST_ENABLE bit(2)
|
|
#define BITFLAG_HARD_LIMIT_ENABLE bit(3)
|
|
#define BITFLAG_HOMING_ENABLE bit(4)
|
|
#define BITFLAG_SOFT_LIMIT_ENABLE bit(5)
|
|
#define BITFLAG_INVERT_LIMIT_PINS bit(6)
|
|
#define BITFLAG_INVERT_PROBE_PIN bit(7)
|
|
|
|
// Define status reporting boolean enable bit flags in settings.status_report_mask
|
|
#define BITFLAG_RT_STATUS_MACHINE_POSITION bit(0)
|
|
#define BITFLAG_RT_STATUS_WORK_POSITION bit(1)
|
|
#define BITFLAG_RT_STATUS_PLANNER_BUFFER bit(2)
|
|
#define BITFLAG_RT_STATUS_SERIAL_RX bit(3)
|
|
|
|
// Define EEPROM memory address location values for Grbl settings and parameters
|
|
// NOTE: The Atmega328p has 1KB EEPROM. The upper half is reserved for parameters and
|
|
// the startup script. The lower half contains the global settings and space for future
|
|
// developments.
|
|
#define EEPROM_ADDR_GLOBAL 1U
|
|
#define EEPROM_ADDR_PARAMETERS 512U
|
|
#define EEPROM_ADDR_STARTUP_BLOCK 768U
|
|
#define EEPROM_ADDR_BUILD_INFO 942U
|
|
|
|
// Define EEPROM address indexing for coordinate parameters
|
|
#define N_COORDINATE_SYSTEM 6 // Number of supported work coordinate systems (from index 1)
|
|
#define SETTING_INDEX_NCOORD N_COORDINATE_SYSTEM+1 // Total number of system stored (from index 0)
|
|
// NOTE: Work coordinate indices are (0=G54, 1=G55, ... , 6=G59)
|
|
#define SETTING_INDEX_G28 N_COORDINATE_SYSTEM // Home position 1
|
|
#define SETTING_INDEX_G30 N_COORDINATE_SYSTEM+1 // Home position 2
|
|
// #define SETTING_INDEX_G92 N_COORDINATE_SYSTEM+2 // Coordinate offset (G92.2,G92.3 not supported)
|
|
|
|
// Define Grbl axis settings numbering scheme. Starts at START_VAL, every INCREMENT, over N_SETTINGS.
|
|
#define AXIS_N_SETTINGS 4
|
|
#define AXIS_SETTINGS_START_VAL 100 // NOTE: Reserving settings values >= 100 for axis settings. Up to 255.
|
|
#define AXIS_SETTINGS_INCREMENT 10 // Must be greater than the number of axis settings
|
|
|
|
// Global persistent settings (Stored from byte EEPROM_ADDR_GLOBAL onwards)
|
|
typedef struct {
|
|
// Axis settings
|
|
float steps_per_mm[N_AXIS];
|
|
float max_rate[N_AXIS];
|
|
float acceleration[N_AXIS];
|
|
float max_travel[N_AXIS];
|
|
|
|
// Remaining Grbl settings
|
|
uint8_t pulse_microseconds;
|
|
uint8_t step_invert_mask;
|
|
uint8_t dir_invert_mask;
|
|
uint8_t stepper_idle_lock_time; // If max value 255, steppers do not disable.
|
|
uint8_t status_report_mask; // Mask to indicate desired report data.
|
|
float junction_deviation;
|
|
float arc_tolerance;
|
|
|
|
uint8_t flags; // Contains default boolean settings
|
|
|
|
uint8_t homing_dir_mask;
|
|
float homing_feed_rate;
|
|
float homing_seek_rate;
|
|
uint16_t homing_debounce_delay;
|
|
float homing_pulloff;
|
|
} settings_t;
|
|
extern settings_t settings;
|
|
|
|
// Initialize the configuration subsystem (load settings from EEPROM)
|
|
void settings_init();
|
|
|
|
// Helper functions to clear and restore EEPROM defaults
|
|
void settings_restore_global_settings();
|
|
void settings_clear_parameters();
|
|
void settings_clear_startup_line();
|
|
void settings_clear_build_info();
|
|
|
|
// A helper method to set new settings from command line
|
|
uint8_t settings_store_global_setting(uint8_t parameter, float value);
|
|
|
|
// Stores the protocol line variable as a startup line in EEPROM
|
|
void settings_store_startup_line(uint8_t n, char *line);
|
|
|
|
// Reads an EEPROM startup line to the protocol line variable
|
|
uint8_t settings_read_startup_line(uint8_t n, char *line);
|
|
|
|
// Stores build info user-defined string
|
|
void settings_store_build_info(char *line);
|
|
|
|
// Reads build info user-defined string
|
|
uint8_t settings_read_build_info(char *line);
|
|
|
|
// Writes selected coordinate data to EEPROM
|
|
void settings_write_coord_data(uint8_t coord_select, float *coord_data);
|
|
|
|
// Reads selected coordinate data from EEPROM
|
|
uint8_t settings_read_coord_data(uint8_t coord_select, float *coord_data);
|
|
|
|
// Returns the step pin mask according to Grbl's internal axis numbering
|
|
uint8_t get_step_pin_mask(uint8_t i);
|
|
|
|
// Returns the direction pin mask according to Grbl's internal axis numbering
|
|
uint8_t get_direction_pin_mask(uint8_t i);
|
|
|
|
// Returns the limit pin mask according to Grbl's internal axis numbering
|
|
uint8_t get_limit_pin_mask(uint8_t i);
|
|
|
|
|
|
#endif
|