b9c3461932
- G38.x was not printing correctly in the $G g-code state reports. Now fixed. - When investigating the above issue, it was noticed that G38.x wouldn’t show at all, but instead a G0 would be printed. This was unlike the v0.9j master build. It turned out volatile variables do not like to be defined inside a C struct. These are undefined on how to be handled. Once pulled out, all weird issues went away. - Also changed two ‘sizeof()’ statements in the mc_probe() and probe_state_monitor() functions to be more robust later on. - Updated the commit logs to individual files for each minor release. Forgot to update the generating script to account for this.
872 lines
24 KiB
Plaintext
872 lines
24 KiB
Plaintext
----------------
|
||
Date: 2015-08-14
|
||
Author: Sonny Jeon
|
||
Subject: Individual control pin invert compile-option.
|
||
|
||
- Control pins may be individually inverted through a
|
||
CONTROL_INVERT_MASK macro. This mask is define in the cpu_map.h file.
|
||
|
||
|
||
----------------
|
||
Date: 2015-07-17
|
||
Author: Sonny Jeon
|
||
Subject: Version bump to v0.9j
|
||
|
||
- Version bump requested by OEMs to easily determine whether the
|
||
firmware supports the new EEPROM reset feature. Other than that, no
|
||
significant changes.
|
||
|
||
|
||
----------------
|
||
Date: 2015-06-25
|
||
Author: Sonny Jeon
|
||
Subject: Restore parameters minor bug fix.
|
||
|
||
- `$RST=#` was not wiping the G30 positions from EEPROM. Minor but now
|
||
fixed.
|
||
|
||
|
||
----------------
|
||
Date: 2015-06-20
|
||
Author: Sonny Jeon
|
||
Subject: New EEPROM restore functions.
|
||
|
||
- Tweaked the previous EEPROM restore implementation and added new
|
||
functionality.
|
||
|
||
- `$RST=$` restores the `$$` grbl settings back to firmware defaults,
|
||
which are set when compiled.
|
||
|
||
- `$RST=#` restores the `$#` parameters in EEPROM. At times it’s useful
|
||
to clear these and start over, rather than manually writing each entry.
|
||
|
||
-`$RST=*` wipe all of the data in EEPROM that Grbl uses and restores
|
||
them to defaults. This includes `$$` settings, `$#` parameters, `$N`
|
||
startup lines, and `$i` build info string.
|
||
|
||
NOTE: This doesn’t write zeros throughout the EEPROM. It only writes
|
||
where Grbl looks for data. For a complete wipe, please use the Arduino
|
||
IDE’s EEPROM clear example.
|
||
|
||
- Refactored the restore and wipe functions in settings.c to
|
||
accommodate the new commands.
|
||
|
||
|
||
----------------
|
||
Date: 2015-06-18
|
||
Author: Sonny Jeon
|
||
Subject: Updated README
|
||
|
||
|
||
----------------
|
||
Date: 2015-06-18
|
||
Author: Sonny Jeon
|
||
Subject: Added restore settings defaults command.
|
||
|
||
- New restore setting defaults command. Only wipes ‘$$’ setting in
|
||
EEPROM and reloads them based on the defaults used when Grbl was
|
||
compiled. Used with a `$RST` command
|
||
|
||
NOTE: `$RST` is intentionally not listed in the Grbl ‘$’ help message.
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-29
|
||
Author: Sonny Jeon
|
||
Subject: Added G61 exact path support.
|
||
|
||
- G61 exact path is the Grbl default path control mode, so it’s now
|
||
added as a supported g-code.
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-27
|
||
Author: Sonny Jeon
|
||
Subject: Another git case-sensitive folder fix.
|
||
|
||
- I’m now officially annoyed.
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-27
|
||
Author: Sonny Jeon
|
||
Subject: Added X-Carve defaults.
|
||
|
||
- Added X-Carve 500mm and 1000mm default files.
|
||
|
||
- Tweaked all default files. Removed obsolete AUTO_START and updated
|
||
some JUNCTION_DEVIATION defaults after testing showed these needed to
|
||
be reduced slightly.
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-27
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #710 from buserror/fix-directory-case-sensitivity
|
||
|
||
Rename Grbl to grbl
|
||
|
||
----------------
|
||
Date: 2015-05-27
|
||
Author: Michel Pollet
|
||
Subject: Rename Grbl to grbl
|
||
|
||
Otherwise compilation fails on linux, or other case sensitive systems
|
||
|
||
Signed-off-by: Michel Pollet <buserror@gmail.com>
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-26
|
||
Author: Sonny Jeon
|
||
Subject: Updated README
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-26
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #706 from grbl/edge
|
||
|
||
Merge edge branch.
|
||
|
||
----------------
|
||
Date: 2015-05-23
|
||
Author: Sonny Jeon
|
||
Subject: CoreXY planner bug fix.
|
||
|
||
- CoreXY motions were moving to the negative value of the intended
|
||
target. Now fixed.
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-23
|
||
Author: Sonny Jeon
|
||
Subject: Moved cpu_map.
|
||
|
||
- Moved cpu_map files to a cpu_map directory, like the defaults file
|
||
organization.
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-23
|
||
Author: Sonny Jeon
|
||
Subject: Homing and limit updates. Minor bug fixes.
|
||
|
||
- Updated new homing cycle to error out when a pull-off motion detects
|
||
the limit is still active.
|
||
|
||
- Created a limits_get_state() function to centralize it. It reports
|
||
state as a bit-wise booleans according to axis numbering.
|
||
|
||
- Updated the print uint8 functions. Generalized it to allow both base2
|
||
and base10 printouts, while allowing base2 prints with N_AXIS digits
|
||
for limit state status reports. Doing this saved about 100bytes of
|
||
flash as well.
|
||
|
||
- Applied CoreXY status reporting bug fix by @phd0. Thanks!
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-22
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #702 from ashelly/default-split
|
||
|
||
Moving defaults to individual files in subdirectory
|
||
|
||
----------------
|
||
Date: 2015-05-22
|
||
Author: ashelly
|
||
Subject: Moving defaults to individual files in subdirectory
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-22
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #700 from ashelly/header-split
|
||
|
||
Header split
|
||
|
||
----------------
|
||
Date: 2015-05-22
|
||
Author: ashelly
|
||
Subject: Fixing up comment blocks in headers
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-22
|
||
Author: ashelly
|
||
Subject: Splitting Cpu map into separate files.
|
||
|
||
Makes comparison, addition of new ones easier
|
||
|
||
|
||
----------------
|
||
Date: 2015-05-17
|
||
Author: Sonny Jeon
|
||
Subject: Critical M0/2/30 fix. Homing updates.
|
||
|
||
- Critical fix for M0 program pause. Due to its recent change, it would
|
||
cause Grbl to suspend but wouldn’t notify the user of why Grbl was not
|
||
doing anything. The state would show IDLE and a cycle start would
|
||
resume it. Grbl now enters a HOLD state to better indicate the state
|
||
change.
|
||
|
||
- Critical fix for M2 and M30 program end. As with M0, the state
|
||
previously would show IDLE while suspended. Grbl now does not suspend
|
||
upon program end and leaves job control to the GUI. Grbl simply reports
|
||
a `[Pgm End]` as a feedback message and resets certain g-code modes.
|
||
|
||
- M2/30 g-code reseting fix. Previously Grbl would soft-reset after an
|
||
M2/30, but this was not complaint to the (linuxcnc) g-code standard. It
|
||
simply resets [G1,G17,G90,G94,G40,G54,M5,M9,M48] and keeps all other
|
||
modes the same.
|
||
|
||
- M0/M2/M30 check-mode fix. It now does not suspend the machine during
|
||
check-mode.
|
||
|
||
- Minor bug fix related to commands similar to G90.1, but not G90.1,
|
||
not reporting an unsupported command.
|
||
|
||
- Homing cycle refactoring. To help reduce the chance of users
|
||
misunderstanding their limit switch wiring, Grbl only moves a short
|
||
distance for the locate cycles only. In addition, the homing cycle
|
||
pulls-off the limit switch by the pull-off distance to re-engage and
|
||
locate home. This should improve its accuracy.
|
||
|
||
- HOMING_FORCE_ORIGIN now sets the origin to the pull-off location,
|
||
rather than where the limit switch was triggered.
|
||
|
||
- Updated default junction deviation to 0.01mm. Recent tests showed
|
||
that this improves Grbl’s cornering behavior a bit.
|
||
|
||
- Added the ShapeOko3 defaults.
|
||
|
||
- Added new feedback message `[Pgm End]` for M2/30 notification.
|
||
|
||
- Limit pin reporting is now a $10 status report option. Requested by
|
||
OEMs to help simplify support troubleshooting.
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-29
|
||
Author: Sonny Jeon
|
||
Subject: Fix for limit pin reporting compile-option
|
||
|
||
- The limit pin reporting wasn’t working correctly due to calling the
|
||
wrong similarly-named function. Verified to be working now.
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-29
|
||
Author: Sonny Jeon
|
||
Subject: Commit history, logo license, full-arc fix.
|
||
|
||
- Commit history added to repo, as an easier way for people to see view
|
||
the changes over time.
|
||
|
||
- Grbl logo copyright license added. All rights reserved with regards
|
||
to the Grbl logo.
|
||
|
||
- G2/3 full circles would sometime not execute. The problem was due to
|
||
numerical round-off of a trig calculation. Added a machine epsilon
|
||
define to help detect and correct for this problem. Tested and should
|
||
not effect general operation of arcs.
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-27
|
||
Author: Sungeun Jeon
|
||
Subject: Compile-option for inverting spindle enable.
|
||
|
||
- Installed a compile-option for inverting the spindle enable pin for
|
||
certain electronics boards users have reported needing this.
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-27
|
||
Author: Sungeun Jeon
|
||
Subject: New compile options and inverse time bug fix.
|
||
|
||
- Apparently inverse time motion were not working for quite some time.
|
||
Goes to show how many people actually use it. The calculation was bad
|
||
and is now fixed in this update. It should now work correctly.
|
||
|
||
- `;` comment type is now supported. This is standard on LinuxCNC and
|
||
common on 3d printers. It was previously not supported due to not
|
||
existing in the NIST standard, which is out-dated.
|
||
|
||
- New compile-option to ECHO the line received. This should help users
|
||
experiencing very weird problems and help diagnose if there is
|
||
something amiss in the communication to Grbl.
|
||
|
||
- New compile-option to use the spindle direction pin D13 as a spindle
|
||
enable pin with PWM spindle speed on D11. This feature has been
|
||
requested often from the laser cutter community. Since spindle
|
||
direction isn’t really of much use, it seemed like good good trade.
|
||
Note that M4 spindle enable counter-clock-wise support is removed for
|
||
obvious reasons, while M3 and M5 still work.
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-27
|
||
Author: Sonny Jeon
|
||
Subject: Update README.md
|
||
|
||
----------------
|
||
Date: 2015-03-26
|
||
Author: Sonny Jeon
|
||
Subject: Update README.md
|
||
|
||
----------------
|
||
Date: 2015-03-16
|
||
Author: Sonny Jeon
|
||
Subject: Update README.md
|
||
|
||
----------------
|
||
Date: 2015-03-15
|
||
Author: Sungeun Jeon
|
||
Subject: Updated README
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-15
|
||
Author: Sonny Jeon
|
||
Subject: Create README.md
|
||
|
||
----------------
|
||
Date: 2015-03-15
|
||
Author: Sungeun Jeon
|
||
Subject: Merge branch 'edge'
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-15
|
||
Author: Sungeun Jeon
|
||
Subject: Updated README.
|
||
|
||
- Also altered the G38.X reporting to save some bytes.
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-14
|
||
Author: Sungeun Jeon
|
||
Subject: Cleaned-up limit pin reporting and comments.
|
||
|
||
- Cleaned up the limit pin state reporting option to display only the
|
||
state per axis, rather than the whole port. It’s organized by an XYZ
|
||
order, 0(low)-1(high), and generally looks like `Lim:001`.
|
||
|
||
- Separated the control pin state reporting from limit state reporting
|
||
as a new compile option. This stayed the same in terms of showing the
|
||
entire port in binary, since it’s not anticipated that this will be
|
||
used much, if at all.
|
||
|
||
- Updated some of the gcode source comments regarding supported g-codes.
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-07
|
||
Author: Sonny Jeon
|
||
Subject: Another homing cycle fix.
|
||
|
||
- The homing cycle should be working again. Reverted it back to how it
|
||
was about a month ago before I started to fiddle with it. Turns out
|
||
that my past self knew what he was doing.
|
||
|
||
|
||
----------------
|
||
Date: 2015-03-04
|
||
Author: Sonny Jeon
|
||
Subject: Arduino IDE compatibility and minor homing fixes
|
||
|
||
- Added an include in the right spot, if a user tries to compile and
|
||
upload Grbl through the Arduino IDE with the old way.
|
||
|
||
- Fixed a minor bug with homing max travel calculations. It was causing
|
||
simultaneous axes homing to move slow than it did before.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-25
|
||
Author: Sonny Jeon
|
||
Subject: G91.1 support. Fixed a config.h option.
|
||
|
||
- G91.1 support added. This g-code sets the arc IJK distance mode to
|
||
incremental, which is the default already. This simply helps reduce
|
||
parsing errors with certain CAM programs that output this command.
|
||
|
||
- Max step rate checks weren’t being compiled in if the option was
|
||
enabled. Fixed now.
|
||
|
||
- Alarm codes were not displaying correctly when GUI reporting mode was
|
||
enabled. Due to unsigned int problem. Changed codes to positive values
|
||
since they aren’t shared with other codes.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-23
|
||
Author: Sonny Jeon
|
||
Subject: Fixed config.h to Grbl release defaults.
|
||
|
||
- REPORT_GUI_MODE was accidentally enabled, when it shouldn’t have.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-23
|
||
Author: Sonny Jeon
|
||
Subject: New configuration options.
|
||
|
||
- New configuration option at compile-time:
|
||
- Force alarm upon power-up or hard reset. When homing is enabled,
|
||
this is already the default behavior. This simply forces this all of
|
||
the time.
|
||
- GUI reporting mode. Removes most human-readable strings that GUIs
|
||
don’t need. This saves nearly 2KB in flash space that can be used for
|
||
other features.
|
||
- Hard limit force state check: In the hard limit pin change ISR, Grbl
|
||
by default sets the hard limit alarm upon any pin change to guarantee
|
||
the alarm is set. If this option is set, it’ll check the state within
|
||
the ISR, but can’t guarantee the pin will be read correctly if the
|
||
switch is bouncing. This option makes hard limit behavior a little less
|
||
annoying if you have a good buffered switch circuit that removes
|
||
bouncing and electronic noise.
|
||
|
||
- Software debounce bug fix. It was reading the pin incorrectly for the
|
||
setting.
|
||
|
||
- Re-factored some of the ‘$’ settings code.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-15
|
||
Author: Sonny Jeon
|
||
Subject: Improved homing limit search handling.
|
||
|
||
- Instead of a single overall max travel for a search distance for the
|
||
homing limit switches. The homing cycle now applies the max travel of
|
||
each axis to the search target. Generally makes more sense this way and
|
||
saved more than a 100bytes of flash too.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-15
|
||
Author: Sonny Jeon
|
||
Subject: Homing alarm upon no switch. Licensing update.
|
||
|
||
- Homing cycle failure reports alarm feedback when the homing cycle is
|
||
exited via a reset, interrupted by a safety door switch, or does not
|
||
find the limit switch.
|
||
|
||
- Homing cycle bug fix when not finding the limit switch. It would just
|
||
idle before, but now will exit with an alarm.
|
||
|
||
- Licensing update. Corrected licensing according to lawyer
|
||
recommendations. Removed references to other Grbl versions.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #593 from poelstra/fix_makefile_deps
|
||
|
||
Fix generating header dependencies, merge with 'normal' compile, force r...
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Sonny Jeon
|
||
Subject: Updated README with new logo sized for github.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Sonny Jeon
|
||
Subject: Update README.md
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Sonny Jeon
|
||
Subject: Doc re-org. New Grbl Logos!
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #591 from EliteEng/edge
|
||
|
||
Safety Door Update for Mega2560
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #592 from poelstra/fix_softlimit
|
||
|
||
Fix EXEC_ALARM_* flags: soft limit would lead to hard limit error.
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #594 from poelstra/fix_sim_build
|
||
|
||
Fix function signature of print_uint32_base10(), necessary for compiling simulator.
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Martin Poelstra
|
||
Subject: Fix function signature of print_uint32_base10(), necessary for compiling simulator.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Martin Poelstra
|
||
Subject: Fix generating header dependencies, merge with 'normal' compile, force recompile when files are removed.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Martin Poelstra
|
||
Subject: Fix EXEC_ALARM_* flags: soft limit would lead to hard limit error.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-13
|
||
Author: Rob Brown
|
||
Subject: Safety Door Update for Mega2560
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-11
|
||
Author: Sonny Jeon
|
||
Subject: Overhauled state machine. New safety door feature.
|
||
|
||
- Overhauled the state machine and cleaned up its overall operation.
|
||
This involved creating a new ‘suspend’ state for what all external
|
||
commands, except real-time commands, are ignored. All hold type states
|
||
enter this suspend state.
|
||
|
||
- Removed ‘auto cycle start’ setting from Grbl. This was not used by
|
||
users in its intended way and is somewhat redundant, as GUI manage the
|
||
cycle start by streaming. It also muddled up how Grbl should interpret
|
||
how and when to execute a g-code block. Removing it made everything
|
||
much much simpler.
|
||
|
||
- Fixed a program pause bug when used with other buffer_sync commands.
|
||
|
||
- New safety door feature for OEMs. Immediately forces a feed hold and
|
||
then de-energizes the machine. Resuming is blocked until the door is
|
||
closed. When it is, it re-energizes the system and then resumes on the
|
||
normal toolpath.
|
||
|
||
- Safety door input pin is optional and uses the feed hold pin on A1.
|
||
Enabled by config.h define.
|
||
|
||
- Spindle and coolant re-energizing upon a safety door resume has a
|
||
programmable delay time to allow for complete spin up to rpm and
|
||
turning on the coolant before resuming motion.
|
||
|
||
- Safety door-style feed holds can be used instead of regular feed hold
|
||
(doesn’t de-energize the machine) with a ‘@‘ character. If the safety
|
||
door input pin is not enabled, the system can be resumed at any time.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-10
|
||
Author: Sonny Jeon
|
||
Subject: Git fix for empty directory. Makefile updated.
|
||
|
||
- ‘build’ directory was not being synced by git because it was empty.
|
||
Added a .gitignore file in the ‘build’ directory to force git to sync
|
||
it but keep it empty.
|
||
|
||
- Updated the Makefile to not erase the .gitignore.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-10
|
||
Author: Sonny Jeon
|
||
Subject: File re-organization. New Makefile.
|
||
|
||
- Re-organized source code files into a ‘grbl’ directory to lessen one
|
||
step in compiling Grbl through the Arduino IDE.
|
||
|
||
- Added an ‘examples’ directory with an upload .INO sketch to further
|
||
simplify compiling and uploading Grbl via the Arduino IDE.
|
||
|
||
- Updated the Makefile with regard to the source code no longer being
|
||
in the root directory. All files generated by compiling is placed in a
|
||
separate ‘build’ directory to keep things tidy. The makefile should
|
||
operate in the same way as it did before.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-10
|
||
Author: Sonny Jeon
|
||
Subject: Bug fix for certain motions. Re-org of includes.
|
||
|
||
- Critical bug fix for diagonal motions that continue on the same
|
||
direction or return in the exact opposite direction. This issue could
|
||
cause Grbl to crash intermittently due to a numerical round-off error.
|
||
Grbl versions prior to v0.9g shouldn’t have this issue.
|
||
|
||
- Reorganized all of the includes used by Grbl. Centralized it into a
|
||
single “grbl.h” include. This will help simplify the compiling and
|
||
uploading process through the Arduino IDE.
|
||
|
||
- Added an example .INO file for users to simply open and run when
|
||
compiling and uploading through the IDE. More to come later.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-06
|
||
Author: Sonny Jeon
|
||
Subject: Limit/control pin state reporting option
|
||
|
||
- As a setup feature, users can compile-in input pin status reporting.
|
||
Doesn’t do anything special, just prints the binary for the port. 0’s
|
||
and 1’s indicate low and high signals on the pins. It’s a bit cryptic
|
||
right now, but it’s just a start.
|
||
|
||
- Added a max step rate check when writing step/mm and max rate
|
||
settings. Should help avoid people misdiagnosing problems associated
|
||
with going over the 30kHz step rate limit. Right now not enabled. Takes
|
||
up over 100k of flash. Need that room for other things right now.
|
||
|
||
|
||
----------------
|
||
Date: 2015-02-04
|
||
Author: Sonny Jeon
|
||
Subject: Rare planner bug fix and added simulator defaults.
|
||
|
||
- Planner bug when moving along a diagonal back and forth on the same
|
||
path. Rare for the fact that most CAM programs don’t program this type
|
||
of motion, neither does jogging. Fixed in this update.
|
||
|
||
- Added grbl_sim defaults for testing purposes.
|
||
|
||
|
||
----------------
|
||
Date: 2015-01-17
|
||
Author: Sonny Jeon
|
||
Subject: Fully configurable pins for NO or NC switches.
|
||
|
||
- All pins, which include limits, control command, and probe pins, can
|
||
now all be configured to trigger as active-low or active-high and
|
||
whether the pin has its internal pull-up resistor enabled. This should
|
||
allow for just about all types of NO and NC switch configurations.
|
||
|
||
- The probe pin invert setting hasn’t been added to the Grbl settings,
|
||
like the others, and will have to wait until v1.0. But for now, it’s
|
||
available as a compile-time option in config.h.
|
||
|
||
- Fixed a variable spindle bug.
|
||
|
||
|
||
----------------
|
||
Date: 2015-01-14
|
||
Author: Sonny Jeon
|
||
Subject: Lot of refactoring for the future. CoreXY support.
|
||
|
||
- Rudimentary CoreXY kinematics support. Didn’t test, but homing and
|
||
feed holds should work. See config.h. Please report successes and
|
||
issues as we find bugs.
|
||
|
||
- G40 (disable cutter comp) is now “supported”. Meaning that Grbl will
|
||
no longer issue an error when typically sent in g-code program header.
|
||
|
||
- Refactored coolant and spindle state setting into separate functions
|
||
for future features.
|
||
|
||
- Configuration option for fixing homing behavior when there are two
|
||
limit switches on the same axis sharing an input pin.
|
||
|
||
- Created a new “grbl.h” that will eventually be used as the main
|
||
include file for Grbl. Also will help simply uploading through the
|
||
Arduino IDE
|
||
|
||
- Separated out the alarms execution flags from the realtime (used be
|
||
called runtime) execution flag variable. Now reports exactly what
|
||
caused the alarm. Expandable for new alarms later on.
|
||
|
||
- Refactored the homing cycle to support CoreXY.
|
||
|
||
- Applied @EliteEng updates to Mega2560 support. Some pins were
|
||
reconfigured.
|
||
|
||
- Created a central step to position and vice versa function. Needed
|
||
for non-traditional cartesian machines. Should make it easier later.
|
||
|
||
- Removed the new CPU map for the Uno. No longer going to used. There
|
||
will be only one configuration to keep things uniform.
|
||
|
||
|
||
----------------
|
||
Date: 2014-11-05
|
||
Author: Sonny Jeon
|
||
Subject: Update README.md
|
||
|
||
----------------
|
||
Date: 2014-10-29
|
||
Author: Sonny Jeon
|
||
Subject: Update README.md
|
||
|
||
----------------
|
||
Date: 2014-10-28
|
||
Author: Sonny Jeon
|
||
Subject: Update README.md
|
||
|
||
----------------
|
||
Date: 2014-10-28
|
||
Author: Sonny Jeon
|
||
Subject: Update README.md
|
||
|
||
----------------
|
||
Date: 2014-10-01
|
||
Author: Sonny Jeon
|
||
Subject: Updated variable spindle and new probing. Minor bug fixes.
|
||
|
||
- Minor bug fix for variable spindle PWM output. Values smaller than
|
||
the minimum RPM for the spindle would overflow the PWM value. Thanks
|
||
Rob!
|
||
|
||
- Created an optional minimum spindle PWM low-mark value as a
|
||
compile-time option. This is for special circumstances when the PWM has
|
||
to be at a certain level to be read by the spindle controller.
|
||
|
||
- Refactored the new probing commands (G38.3, G38.4, G38.5) code to
|
||
work better with the rest of Grbl’s systems.
|
||
|
||
- Refactored mc_probe() and mc_arc() to accept the mode of the command,
|
||
i.e. clockwise vs counter, toward vs away, etc. This is to make these
|
||
functions independent of gcode state variables.
|
||
|
||
- Removed the pull off motion in the probing cycle. This is not an
|
||
official operation and was added for user simplicity, but wrongly did
|
||
so. So bye bye.
|
||
|
||
- Created a configure probe invert mask function to handle the
|
||
different probe pin setting and probing cycle modes with a single mask.
|
||
|
||
- Minor bug fix with reporting motion modes via $G. G38.2 wasn’t
|
||
showing up. It now does, along with the other new probing commands.
|
||
|
||
- Refactored some of the new pin configurations for the future of Grbl.
|
||
|
||
-
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-25
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #491 from tmpvar/G38.2+
|
||
|
||
G38.2+
|
||
|
||
----------------
|
||
Date: 2014-09-22
|
||
Author: Elijah Insua
|
||
Subject: report probe_succeeded with probe status
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-22
|
||
Author: Elijah Insua
|
||
Subject: add probe_finalize to keep things DRY
|
||
|
||
this allows the PRB report to be valid when in "no errors" mode and the probe fails
|
||
|
||
----------------
|
||
Date: 2014-09-22
|
||
Author: Elijah Insua
|
||
Subject: hop over probe pull-off sequence after probe miss
|
||
|
||
and while "no errors" is enabled (G38.3, G38.5)
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-22
|
||
Author: Elijah Insua
|
||
Subject: add/install probe_errors_enabled in mc_probe_cycle
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-22
|
||
Author: Elijah Insua
|
||
Subject: bump mantissa to uint16_t to enable G38.5
|
||
|
||
----------------
|
||
Date: 2014-09-22
|
||
Author: Elijah Insua
|
||
Subject: test only for & PROBE_ACTIVE
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-22
|
||
Author: Elijah Insua
|
||
Subject: cleanup global var and push probe mode into probe_get_state
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-20
|
||
Author: Sonny Jeon
|
||
Subject: Edit hard limit check at start of homing cycle
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-20
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #494 from ashelly/homing-alarm
|
||
|
||
Alarm if limits engaged on homing start.
|
||
|
||
----------------
|
||
Date: 2014-09-20
|
||
Author: Sonny Jeon
|
||
Subject: Merge pull request #493 from alpharesearch/edge
|
||
|
||
If variable spindle is defined print S value via $G command.
|
||
|
||
----------------
|
||
Date: 2014-09-20
|
||
Author: Sonny Jeon
|
||
Subject: Minor settings number overflow bug fix.
|
||
|
||
- The `x` in `$x=val` would overflow when a value larger than 255 was
|
||
entered and passed to Grbl. This resulted with unintended parameters
|
||
being set by the overflow value. To fix, simply check for values larger
|
||
than 255 and error out.
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-17
|
||
Author: ashelly
|
||
Subject: No false alarm if other bits in port are set.
|
||
|
||
----------------
|
||
Date: 2014-09-17
|
||
Author: Markus Schulz
|
||
Subject: If variable spindle is defined print S value via $G command.
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-14
|
||
Author: Elijah Insua
|
||
Subject: utilize MOTION_MODE_PROBE_NO_ERROR
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-14
|
||
Author: Elijah Insua
|
||
Subject: install G38.{3,4,5}
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-14
|
||
Author: Elijah Insua
|
||
Subject: add MOTION_MODE_PROBE_NO_ERROR
|
||
|
||
|
||
----------------
|
||
Date: 2014-09-08
|
||
Author: ashelly
|
||
Subject: Alarm if limits engaged on homing
|
||
|