5eee10845b
- New pin state realtime reporting feature. Instead of `Lim:000` for limit state reports, the new feature shows `Pin:000|0|0000`, or something similar. The `|` delimited fields indicate xyz limits, probe, and control pin states, where 0 is always not triggered, and 1 is triggered. Invert masks ARE accounted for. Each field may be enabled or disabled via the `$10` status report setting. The probe and control pin flags are bits 5 and 6, respectively. - Remove the now deprecated `REPORT_CONTROL_PIN_STATE` option in config.h - The old limit pin reports `Lim:000` may be re-enabled by commenting out `REPORT_ALL_PIN_STATES` in config.h. - Incremented the version letter (v1.0c) to indicate the change in reporting style. - Replaced all bit_true_atomic and bit_false_atomic macros with function calls. This saved a couple hundred bytes of flash.
531 lines
23 KiB
C
531 lines
23 KiB
C
/*
|
|
report.c - reporting and messaging methods
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2012-2015 Sungeun K. Jeon
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/*
|
|
This file functions as the primary feedback interface for Grbl. Any outgoing data, such
|
|
as the protocol status messages, feedback messages, and status reports, are stored here.
|
|
For the most part, these functions primarily are called from protocol.c methods. If a
|
|
different style feedback is desired (i.e. JSON), then a user can change these following
|
|
methods to accomodate their needs.
|
|
*/
|
|
|
|
#include "grbl.h"
|
|
|
|
|
|
// Handles the primary confirmation protocol response for streaming interfaces and human-feedback.
|
|
// For every incoming line, this method responds with an 'ok' for a successful command or an
|
|
// 'error:' to indicate some error event with the line or some critical system error during
|
|
// operation. Errors events can originate from the g-code parser, settings module, or asynchronously
|
|
// from a critical error, such as a triggered hard limit. Interface should always monitor for these
|
|
// responses.
|
|
// NOTE: In silent mode, all error codes are greater than zero.
|
|
// TODO: Install silent mode to return only numeric values, primarily for GUIs.
|
|
void report_status_message(uint8_t status_code)
|
|
{
|
|
if (status_code == 0) { // STATUS_OK
|
|
printPgmString(PSTR("ok\r\n"));
|
|
} else {
|
|
printPgmString(PSTR("error: "));
|
|
#ifdef REPORT_GUI_MODE
|
|
print_uint8_base10(status_code);
|
|
#else
|
|
switch(status_code) {
|
|
case STATUS_EXPECTED_COMMAND_LETTER:
|
|
printPgmString(PSTR("Expected command letter")); break;
|
|
case STATUS_BAD_NUMBER_FORMAT:
|
|
printPgmString(PSTR("Bad number format")); break;
|
|
case STATUS_INVALID_STATEMENT:
|
|
printPgmString(PSTR("Invalid statement")); break;
|
|
case STATUS_NEGATIVE_VALUE:
|
|
printPgmString(PSTR("Value < 0")); break;
|
|
case STATUS_SETTING_DISABLED:
|
|
printPgmString(PSTR("Setting disabled")); break;
|
|
case STATUS_SETTING_STEP_PULSE_MIN:
|
|
printPgmString(PSTR("Value < 3 usec")); break;
|
|
case STATUS_SETTING_READ_FAIL:
|
|
printPgmString(PSTR("EEPROM read fail. Using defaults")); break;
|
|
case STATUS_IDLE_ERROR:
|
|
printPgmString(PSTR("Not idle")); break;
|
|
case STATUS_ALARM_LOCK:
|
|
printPgmString(PSTR("Alarm lock")); break;
|
|
case STATUS_SOFT_LIMIT_ERROR:
|
|
printPgmString(PSTR("Homing not enabled")); break;
|
|
case STATUS_OVERFLOW:
|
|
printPgmString(PSTR("Line overflow")); break;
|
|
#ifdef MAX_STEP_RATE_HZ
|
|
case STATUS_MAX_STEP_RATE_EXCEEDED:
|
|
printPgmString(PSTR("Step rate > 30kHz")); break;
|
|
#endif
|
|
case STATUS_CHECK_DOOR:
|
|
printPgmString(PSTR("Check Door")); break;
|
|
// Common g-code parser errors.
|
|
case STATUS_GCODE_MODAL_GROUP_VIOLATION:
|
|
printPgmString(PSTR("Modal group violation")); break;
|
|
case STATUS_GCODE_UNSUPPORTED_COMMAND:
|
|
printPgmString(PSTR("Unsupported command")); break;
|
|
case STATUS_GCODE_UNDEFINED_FEED_RATE:
|
|
printPgmString(PSTR("Undefined feed rate")); break;
|
|
default:
|
|
// Remaining g-code parser errors with error codes
|
|
printPgmString(PSTR("Invalid gcode ID:"));
|
|
print_uint8_base10(status_code); // Print error code for user reference
|
|
}
|
|
#endif
|
|
printPgmString(PSTR("\r\n"));
|
|
}
|
|
}
|
|
|
|
// Prints alarm messages.
|
|
void report_alarm_message(int8_t alarm_code)
|
|
{
|
|
printPgmString(PSTR("ALARM: "));
|
|
#ifdef REPORT_GUI_MODE
|
|
print_uint8_base10(alarm_code);
|
|
#else
|
|
switch (alarm_code) {
|
|
case ALARM_HARD_LIMIT_ERROR:
|
|
printPgmString(PSTR("Hard limit")); break;
|
|
case ALARM_SOFT_LIMIT_ERROR:
|
|
printPgmString(PSTR("Soft limit")); break;
|
|
case ALARM_ABORT_CYCLE:
|
|
printPgmString(PSTR("Abort during cycle")); break;
|
|
case ALARM_PROBE_FAIL:
|
|
printPgmString(PSTR("Probe fail")); break;
|
|
case ALARM_HOMING_FAIL:
|
|
printPgmString(PSTR("Homing fail")); break;
|
|
}
|
|
#endif
|
|
printPgmString(PSTR("\r\n"));
|
|
delay_ms(500); // Force delay to ensure message clears serial write buffer.
|
|
}
|
|
|
|
// Prints feedback messages. This serves as a centralized method to provide additional
|
|
// user feedback for things that are not of the status/alarm message protocol. These are
|
|
// messages such as setup warnings, switch toggling, and how to exit alarms.
|
|
// NOTE: For interfaces, messages are always placed within brackets. And if silent mode
|
|
// is installed, the message number codes are less than zero.
|
|
// TODO: Install silence feedback messages option in settings
|
|
void report_feedback_message(uint8_t message_code)
|
|
{
|
|
printPgmString(PSTR("["));
|
|
switch(message_code) {
|
|
case MESSAGE_CRITICAL_EVENT:
|
|
printPgmString(PSTR("Reset to continue")); break;
|
|
case MESSAGE_ALARM_LOCK:
|
|
printPgmString(PSTR("'$H'|'$X' to unlock")); break;
|
|
case MESSAGE_ALARM_UNLOCK:
|
|
printPgmString(PSTR("Caution: Unlocked")); break;
|
|
case MESSAGE_ENABLED:
|
|
printPgmString(PSTR("Enabled")); break;
|
|
case MESSAGE_DISABLED:
|
|
printPgmString(PSTR("Disabled")); break;
|
|
case MESSAGE_SAFETY_DOOR_AJAR:
|
|
printPgmString(PSTR("Check Door")); break;
|
|
case MESSAGE_PROGRAM_END:
|
|
printPgmString(PSTR("Pgm End")); break;
|
|
case MESSAGE_RESTORE_DEFAULTS:
|
|
printPgmString(PSTR("Restoring defaults")); break;
|
|
}
|
|
printPgmString(PSTR("]\r\n"));
|
|
}
|
|
|
|
|
|
// Welcome message
|
|
void report_init_message()
|
|
{
|
|
printPgmString(PSTR("\r\nGrbl " GRBL_VERSION " ['$' for help]\r\n"));
|
|
}
|
|
|
|
// Grbl help message
|
|
void report_grbl_help() {
|
|
#ifndef REPORT_GUI_MODE
|
|
printPgmString(PSTR("$$ (view Grbl settings)\r\n"
|
|
"$# (view # parameters)\r\n"
|
|
"$G (view parser state)\r\n"
|
|
"$I (view build info)\r\n"
|
|
"$N (view startup blocks)\r\n"
|
|
"$x=value (save Grbl setting)\r\n"
|
|
"$Nx=line (save startup block)\r\n"
|
|
"$C (check gcode mode)\r\n"
|
|
"$X (kill alarm lock)\r\n"
|
|
"$H (run homing cycle)\r\n"
|
|
"~ (cycle start)\r\n"
|
|
"! (feed hold)\r\n"
|
|
"? (current status)\r\n"
|
|
"ctrl-x (reset Grbl)\r\n"));
|
|
#endif
|
|
}
|
|
|
|
|
|
// Grbl global settings print out.
|
|
// NOTE: The numbering scheme here must correlate to storing in settings.c
|
|
void report_grbl_settings() {
|
|
// Print Grbl settings.
|
|
#ifdef REPORT_GUI_MODE
|
|
printPgmString(PSTR("$0=")); print_uint8_base10(settings.pulse_microseconds);
|
|
printPgmString(PSTR("\r\n$1=")); print_uint8_base10(settings.stepper_idle_lock_time);
|
|
printPgmString(PSTR("\r\n$2=")); print_uint8_base10(settings.step_invert_mask);
|
|
printPgmString(PSTR("\r\n$3=")); print_uint8_base10(settings.dir_invert_mask);
|
|
printPgmString(PSTR("\r\n$4=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_INVERT_ST_ENABLE));
|
|
printPgmString(PSTR("\r\n$5=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_INVERT_LIMIT_PINS));
|
|
printPgmString(PSTR("\r\n$6=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_INVERT_PROBE_PIN));
|
|
printPgmString(PSTR("\r\n$10=")); print_uint8_base10(settings.status_report_mask);
|
|
printPgmString(PSTR("\r\n$11=")); printFloat_SettingValue(settings.junction_deviation);
|
|
printPgmString(PSTR("\r\n$12=")); printFloat_SettingValue(settings.arc_tolerance);
|
|
printPgmString(PSTR("\r\n$13=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_REPORT_INCHES));
|
|
printPgmString(PSTR("\r\n$20=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_SOFT_LIMIT_ENABLE));
|
|
printPgmString(PSTR("\r\n$21=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_HARD_LIMIT_ENABLE));
|
|
printPgmString(PSTR("\r\n$22=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_HOMING_ENABLE));
|
|
printPgmString(PSTR("\r\n$23=")); print_uint8_base10(settings.homing_dir_mask);
|
|
printPgmString(PSTR("\r\n$24=")); printFloat_SettingValue(settings.homing_feed_rate);
|
|
printPgmString(PSTR("\r\n$25=")); printFloat_SettingValue(settings.homing_seek_rate);
|
|
printPgmString(PSTR("\r\n$26=")); print_uint8_base10(settings.homing_debounce_delay);
|
|
printPgmString(PSTR("\r\n$27=")); printFloat_SettingValue(settings.homing_pulloff);
|
|
printPgmString(PSTR("\r\n$30=")); printFloat_RPMValue(settings.rpm_max);
|
|
printPgmString(PSTR("\r\n$31=")); printFloat_RPMValue(settings.rpm_min);
|
|
printPgmString(PSTR("\r\n"));
|
|
#else
|
|
printPgmString(PSTR("$0=")); print_uint8_base10(settings.pulse_microseconds);
|
|
printPgmString(PSTR(" (step pulse, usec)\r\n$1=")); print_uint8_base10(settings.stepper_idle_lock_time);
|
|
printPgmString(PSTR(" (step idle delay, msec)\r\n$2=")); print_uint8_base10(settings.step_invert_mask);
|
|
printPgmString(PSTR(" (step port invert mask:")); print_uint8_base2(settings.step_invert_mask);
|
|
printPgmString(PSTR(")\r\n$3=")); print_uint8_base10(settings.dir_invert_mask);
|
|
printPgmString(PSTR(" (dir port invert mask:")); print_uint8_base2(settings.dir_invert_mask);
|
|
printPgmString(PSTR(")\r\n$4=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_INVERT_ST_ENABLE));
|
|
printPgmString(PSTR(" (step enable invert, bool)\r\n$5=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_INVERT_LIMIT_PINS));
|
|
printPgmString(PSTR(" (limit pins invert, bool)\r\n$6=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_INVERT_PROBE_PIN));
|
|
printPgmString(PSTR(" (probe pin invert, bool)\r\n$10=")); print_uint8_base10(settings.status_report_mask);
|
|
printPgmString(PSTR(" (status report mask:")); print_uint8_base2(settings.status_report_mask);
|
|
printPgmString(PSTR(")\r\n$11=")); printFloat_SettingValue(settings.junction_deviation);
|
|
printPgmString(PSTR(" (junction deviation, mm)\r\n$12=")); printFloat_SettingValue(settings.arc_tolerance);
|
|
printPgmString(PSTR(" (arc tolerance, mm)\r\n$13=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_REPORT_INCHES));
|
|
printPgmString(PSTR(" (report inches, bool)\r\n$20=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_SOFT_LIMIT_ENABLE));
|
|
printPgmString(PSTR(" (soft limits, bool)\r\n$21=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_HARD_LIMIT_ENABLE));
|
|
printPgmString(PSTR(" (hard limits, bool)\r\n$22=")); print_uint8_base10(bit_istrue(settings.flags,BITFLAG_HOMING_ENABLE));
|
|
printPgmString(PSTR(" (homing cycle, bool)\r\n$23=")); print_uint8_base10(settings.homing_dir_mask);
|
|
printPgmString(PSTR(" (homing dir invert mask:")); print_uint8_base2(settings.homing_dir_mask);
|
|
printPgmString(PSTR(")\r\n$24=")); printFloat_SettingValue(settings.homing_feed_rate);
|
|
printPgmString(PSTR(" (homing feed, mm/min)\r\n$25=")); printFloat_SettingValue(settings.homing_seek_rate);
|
|
printPgmString(PSTR(" (homing seek, mm/min)\r\n$26=")); print_uint8_base10(settings.homing_debounce_delay);
|
|
printPgmString(PSTR(" (homing debounce, msec)\r\n$27=")); printFloat_SettingValue(settings.homing_pulloff);
|
|
printPgmString(PSTR(" (homing pull-off, mm)\r\n$30=")); printFloat_RPMValue(settings.rpm_max);
|
|
printPgmString(PSTR(" (rpm max)\r\n$31=")); printFloat_RPMValue(settings.rpm_min);
|
|
printPgmString(PSTR(" (rpm min)\r\n"));
|
|
#endif
|
|
|
|
// Print axis settings
|
|
uint8_t idx, set_idx;
|
|
uint8_t val = AXIS_SETTINGS_START_VAL;
|
|
for (set_idx=0; set_idx<AXIS_N_SETTINGS; set_idx++) {
|
|
for (idx=0; idx<N_AXIS; idx++) {
|
|
printPgmString(PSTR("$"));
|
|
print_uint8_base10(val+idx);
|
|
printPgmString(PSTR("="));
|
|
switch (set_idx) {
|
|
case 0: printFloat_SettingValue(settings.steps_per_mm[idx]); break;
|
|
case 1: printFloat_SettingValue(settings.max_rate[idx]); break;
|
|
case 2: printFloat_SettingValue(settings.acceleration[idx]/(60*60)); break;
|
|
case 3: printFloat_SettingValue(-settings.max_travel[idx]); break;
|
|
}
|
|
#ifdef REPORT_GUI_MODE
|
|
printPgmString(PSTR("\r\n"));
|
|
#else
|
|
printPgmString(PSTR(" ("));
|
|
switch (idx) {
|
|
case X_AXIS: printPgmString(PSTR("x")); break;
|
|
case Y_AXIS: printPgmString(PSTR("y")); break;
|
|
case Z_AXIS: printPgmString(PSTR("z")); break;
|
|
}
|
|
switch (set_idx) {
|
|
case 0: printPgmString(PSTR(", step/mm")); break;
|
|
case 1: printPgmString(PSTR(" max rate, mm/min")); break;
|
|
case 2: printPgmString(PSTR(" accel, mm/sec^2")); break;
|
|
case 3: printPgmString(PSTR(" max travel, mm")); break;
|
|
}
|
|
printPgmString(PSTR(")\r\n"));
|
|
#endif
|
|
}
|
|
val += AXIS_SETTINGS_INCREMENT;
|
|
}
|
|
}
|
|
|
|
|
|
// Prints current probe parameters. Upon a probe command, these parameters are updated upon a
|
|
// successful probe or upon a failed probe with the G38.3 without errors command (if supported).
|
|
// These values are retained until Grbl is power-cycled, whereby they will be re-zeroed.
|
|
void report_probe_parameters()
|
|
{
|
|
uint8_t i;
|
|
float print_position[N_AXIS];
|
|
|
|
// Report in terms of machine position.
|
|
printPgmString(PSTR("[PRB:"));
|
|
for (i=0; i< N_AXIS; i++) {
|
|
print_position[i] = system_convert_axis_steps_to_mpos(sys.probe_position,i);
|
|
printFloat_CoordValue(print_position[i]);
|
|
if (i < (N_AXIS-1)) { printPgmString(PSTR(",")); }
|
|
}
|
|
printPgmString(PSTR(":"));
|
|
print_uint8_base10(sys.probe_succeeded);
|
|
printPgmString(PSTR("]\r\n"));
|
|
}
|
|
|
|
|
|
// Prints Grbl NGC parameters (coordinate offsets, probing)
|
|
void report_ngc_parameters()
|
|
{
|
|
float coord_data[N_AXIS];
|
|
uint8_t coord_select, i;
|
|
for (coord_select = 0; coord_select <= SETTING_INDEX_NCOORD; coord_select++) {
|
|
if (!(settings_read_coord_data(coord_select,coord_data))) {
|
|
report_status_message(STATUS_SETTING_READ_FAIL);
|
|
return;
|
|
}
|
|
printPgmString(PSTR("[G"));
|
|
switch (coord_select) {
|
|
case 6: printPgmString(PSTR("28")); break;
|
|
case 7: printPgmString(PSTR("30")); break;
|
|
default: print_uint8_base10(coord_select+54); break; // G54-G59
|
|
}
|
|
printPgmString(PSTR(":"));
|
|
for (i=0; i<N_AXIS; i++) {
|
|
printFloat_CoordValue(coord_data[i]);
|
|
if (i < (N_AXIS-1)) { printPgmString(PSTR(",")); }
|
|
else { printPgmString(PSTR("]\r\n")); }
|
|
}
|
|
}
|
|
printPgmString(PSTR("[G92:")); // Print G92,G92.1 which are not persistent in memory
|
|
for (i=0; i<N_AXIS; i++) {
|
|
printFloat_CoordValue(gc_state.coord_offset[i]);
|
|
if (i < (N_AXIS-1)) { printPgmString(PSTR(",")); }
|
|
else { printPgmString(PSTR("]\r\n")); }
|
|
}
|
|
printPgmString(PSTR("[TLO:")); // Print tool length offset value
|
|
printFloat_CoordValue(gc_state.tool_length_offset);
|
|
printPgmString(PSTR("]\r\n"));
|
|
report_probe_parameters(); // Print probe parameters. Not persistent in memory.
|
|
}
|
|
|
|
|
|
// Print current gcode parser mode state
|
|
void report_gcode_modes()
|
|
{
|
|
printPgmString(PSTR("["));
|
|
|
|
switch (gc_state.modal.motion) {
|
|
case MOTION_MODE_SEEK : printPgmString(PSTR("G0")); break;
|
|
case MOTION_MODE_LINEAR : printPgmString(PSTR("G1")); break;
|
|
case MOTION_MODE_CW_ARC : printPgmString(PSTR("G2")); break;
|
|
case MOTION_MODE_CCW_ARC : printPgmString(PSTR("G3")); break;
|
|
case MOTION_MODE_NONE : printPgmString(PSTR("G80")); break;
|
|
default:
|
|
printPgmString(PSTR("G38."));
|
|
print_uint8_base10(gc_state.modal.motion - (MOTION_MODE_PROBE_TOWARD-2));
|
|
}
|
|
|
|
printPgmString(PSTR(" G"));
|
|
print_uint8_base10(gc_state.modal.coord_select+54);
|
|
|
|
switch (gc_state.modal.plane_select) {
|
|
case PLANE_SELECT_XY : printPgmString(PSTR(" G17")); break;
|
|
case PLANE_SELECT_ZX : printPgmString(PSTR(" G18")); break;
|
|
case PLANE_SELECT_YZ : printPgmString(PSTR(" G19")); break;
|
|
}
|
|
|
|
if (gc_state.modal.units == UNITS_MODE_MM) { printPgmString(PSTR(" G21")); }
|
|
else { printPgmString(PSTR(" G20")); }
|
|
|
|
if (gc_state.modal.distance == DISTANCE_MODE_ABSOLUTE) { printPgmString(PSTR(" G90")); }
|
|
else { printPgmString(PSTR(" G91")); }
|
|
|
|
if (gc_state.modal.feed_rate == FEED_RATE_MODE_INVERSE_TIME) { printPgmString(PSTR(" G93")); }
|
|
else { printPgmString(PSTR(" G94")); }
|
|
|
|
switch (gc_state.modal.program_flow) {
|
|
case PROGRAM_FLOW_RUNNING : printPgmString(PSTR(" M0")); break;
|
|
case PROGRAM_FLOW_PAUSED : printPgmString(PSTR(" M1")); break;
|
|
case PROGRAM_FLOW_COMPLETED : printPgmString(PSTR(" M2")); break;
|
|
}
|
|
|
|
switch (gc_state.modal.spindle) {
|
|
case SPINDLE_ENABLE_CW : printPgmString(PSTR(" M3")); break;
|
|
case SPINDLE_ENABLE_CCW : printPgmString(PSTR(" M4")); break;
|
|
case SPINDLE_DISABLE : printPgmString(PSTR(" M5")); break;
|
|
}
|
|
|
|
switch (gc_state.modal.coolant) {
|
|
case COOLANT_DISABLE : printPgmString(PSTR(" M9")); break;
|
|
case COOLANT_FLOOD_ENABLE : printPgmString(PSTR(" M8")); break;
|
|
#ifdef ENABLE_M7
|
|
case COOLANT_MIST_ENABLE : printPgmString(PSTR(" M7")); break;
|
|
#endif
|
|
}
|
|
|
|
printPgmString(PSTR(" T"));
|
|
print_uint8_base10(gc_state.tool);
|
|
|
|
printPgmString(PSTR(" F"));
|
|
printFloat_RateValue(gc_state.feed_rate);
|
|
|
|
#ifdef VARIABLE_SPINDLE
|
|
printPgmString(PSTR(" S"));
|
|
printFloat_RPMValue(gc_state.spindle_speed);
|
|
#endif
|
|
|
|
printPgmString(PSTR("]\r\n"));
|
|
}
|
|
|
|
// Prints specified startup line
|
|
void report_startup_line(uint8_t n, char *line)
|
|
{
|
|
printPgmString(PSTR("$N")); print_uint8_base10(n);
|
|
printPgmString(PSTR("=")); printString(line);
|
|
printPgmString(PSTR("\r\n"));
|
|
}
|
|
|
|
|
|
// Prints build info line
|
|
void report_build_info(char *line)
|
|
{
|
|
printPgmString(PSTR("[" GRBL_VERSION "." GRBL_VERSION_BUILD ":"));
|
|
printString(line);
|
|
printPgmString(PSTR("]\r\n"));
|
|
}
|
|
|
|
|
|
// Prints the character string line Grbl has received from the user, which has been pre-parsed,
|
|
// and has been sent into protocol_execute_line() routine to be executed by Grbl.
|
|
void report_echo_line_received(char *line)
|
|
{
|
|
printPgmString(PSTR("[echo: ")); printString(line);
|
|
printPgmString(PSTR("]\r\n"));
|
|
}
|
|
|
|
|
|
// Prints real-time data. This function grabs a real-time snapshot of the stepper subprogram
|
|
// and the actual location of the CNC machine. Users may change the following function to their
|
|
// specific needs, but the desired real-time data report must be as short as possible. This is
|
|
// requires as it minimizes the computational overhead and allows grbl to keep running smoothly,
|
|
// especially during g-code programs with fast, short line segments and high frequency reports (5-20Hz).
|
|
void report_realtime_status()
|
|
{
|
|
// **Under construction** Bare-bones status report. Provides real-time machine position relative to
|
|
// the system power on location (0,0,0) and work coordinate position (G54 and G92 applied). Eventually
|
|
// to be added are distance to go on block, processed block id, and feed rate. Also a settings bitmask
|
|
// for a user to select the desired real-time data.
|
|
uint8_t idx;
|
|
int32_t current_position[N_AXIS]; // Copy current state of the system position variable
|
|
memcpy(current_position,sys.position,sizeof(sys.position));
|
|
float print_position[N_AXIS];
|
|
|
|
// Report current machine state
|
|
switch (sys.state) {
|
|
case STATE_IDLE: printPgmString(PSTR("<Idle")); break;
|
|
case STATE_MOTION_CANCEL: // Report run state.
|
|
case STATE_CYCLE: printPgmString(PSTR("<Run")); break;
|
|
case STATE_HOLD: printPgmString(PSTR("<Hold")); break;
|
|
case STATE_HOMING: printPgmString(PSTR("<Home")); break;
|
|
case STATE_ALARM: printPgmString(PSTR("<Alarm")); break;
|
|
case STATE_CHECK_MODE: printPgmString(PSTR("<Check")); break;
|
|
case STATE_SAFETY_DOOR: printPgmString(PSTR("<Door")); break;
|
|
}
|
|
|
|
// If reporting a position, convert the current step count (current_position) to millimeters.
|
|
if (bit_istrue(settings.status_report_mask,(BITFLAG_RT_STATUS_MACHINE_POSITION | BITFLAG_RT_STATUS_WORK_POSITION))) {
|
|
system_convert_array_steps_to_mpos(print_position,current_position);
|
|
}
|
|
|
|
// Report machine position
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_MACHINE_POSITION)) {
|
|
printPgmString(PSTR(",MPos:"));
|
|
for (idx=0; idx< N_AXIS; idx++) {
|
|
printFloat_CoordValue(print_position[idx]);
|
|
if (idx < (N_AXIS-1)) { printPgmString(PSTR(",")); }
|
|
}
|
|
}
|
|
|
|
// Report work position
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_WORK_POSITION)) {
|
|
printPgmString(PSTR(",WPos:"));
|
|
for (idx=0; idx< N_AXIS; idx++) {
|
|
// Apply work coordinate offsets and tool length offset to current position.
|
|
print_position[idx] -= gc_state.coord_system[idx]+gc_state.coord_offset[idx];
|
|
if (idx == TOOL_LENGTH_OFFSET_AXIS) { print_position[idx] -= gc_state.tool_length_offset; }
|
|
printFloat_CoordValue(print_position[idx]);
|
|
if (idx < (N_AXIS-1)) { printPgmString(PSTR(",")); }
|
|
}
|
|
}
|
|
|
|
// Returns the number of active blocks are in the planner buffer.
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_PLANNER_BUFFER)) {
|
|
printPgmString(PSTR(",Buf:"));
|
|
print_uint8_base10(plan_get_block_buffer_count());
|
|
}
|
|
|
|
// Report serial read buffer status
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_SERIAL_RX)) {
|
|
printPgmString(PSTR(",RX:"));
|
|
print_uint8_base10(serial_get_rx_buffer_count());
|
|
}
|
|
|
|
#ifdef USE_LINE_NUMBERS
|
|
// Report current line number
|
|
printPgmString(PSTR(",Ln:"));
|
|
int32_t ln=0;
|
|
plan_block_t * pb = plan_get_current_block();
|
|
if(pb != NULL) {
|
|
ln = pb->line_number;
|
|
}
|
|
printInteger(ln);
|
|
#endif
|
|
|
|
#ifdef REPORT_REALTIME_RATE
|
|
// Report realtime rate
|
|
printPgmString(PSTR(",F:"));
|
|
printFloat_RateValue(st_get_realtime_rate());
|
|
#endif
|
|
|
|
#ifdef REPORT_ALL_PIN_STATES
|
|
if (bit_istrue(settings.status_report_mask,
|
|
( BITFLAG_RT_STATUS_LIMIT_PINS| BITFLAG_RT_STATUS_PROBE_PIN | BITFLAG_RT_STATUS_CONTROL_PINS ))) {
|
|
printPgmString(PSTR(",Pin:"));
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_LIMIT_PINS)) {
|
|
print_unsigned_int8(limits_get_state(),2,N_AXIS);
|
|
}
|
|
printPgmString(PSTR("|"));
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_PROBE_PIN)) {
|
|
if (probe_get_state()) { printPgmString(PSTR("1")); }
|
|
else { printPgmString(PSTR("0")); }
|
|
}
|
|
printPgmString(PSTR("|"));
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_CONTROL_PINS)) {
|
|
print_unsigned_int8(system_control_get_state(),2,N_CONTROL_PIN);
|
|
}
|
|
}
|
|
#else
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_LIMIT_PINS)) {
|
|
printPgmString(PSTR(",Lim:"));
|
|
print_unsigned_int8(limits_get_state(),2,N_AXIS);
|
|
}
|
|
#endif
|
|
|
|
printPgmString(PSTR(">\r\n"));
|
|
}
|