5eee10845b
- New pin state realtime reporting feature. Instead of `Lim:000` for limit state reports, the new feature shows `Pin:000|0|0000`, or something similar. The `|` delimited fields indicate xyz limits, probe, and control pin states, where 0 is always not triggered, and 1 is triggered. Invert masks ARE accounted for. Each field may be enabled or disabled via the `$10` status report setting. The probe and control pin flags are bits 5 and 6, respectively. - Remove the now deprecated `REPORT_CONTROL_PIN_STATE` option in config.h - The old limit pin reports `Lim:000` may be re-enabled by commenting out `REPORT_ALL_PIN_STATES` in config.h. - Incremented the version letter (v1.0c) to indicate the change in reporting style. - Replaced all bit_true_atomic and bit_false_atomic macros with function calls. This saved a couple hundred bytes of flash.
69 lines
2.4 KiB
C
69 lines
2.4 KiB
C
/*
|
|
probe.c - code pertaining to probing methods
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2014-2015 Sungeun K. Jeon
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include "grbl.h"
|
|
|
|
|
|
// Inverts the probe pin state depending on user settings and probing cycle mode.
|
|
uint8_t probe_invert_mask;
|
|
|
|
|
|
// Probe pin initialization routine.
|
|
void probe_init()
|
|
{
|
|
PROBE_DDR &= ~(PROBE_MASK); // Configure as input pins
|
|
#ifdef DISABLE_PROBE_PIN_PULL_UP
|
|
PROBE_PORT &= ~(PROBE_MASK); // Normal low operation. Requires external pull-down.
|
|
#else
|
|
PROBE_PORT |= PROBE_MASK; // Enable internal pull-up resistors. Normal high operation.
|
|
#endif
|
|
probe_configure_invert_mask(false); // Initialize invert mask. Re-updated during use.
|
|
}
|
|
|
|
|
|
// Called by probe_init() and the mc_probe() routines. Sets up the probe pin invert mask to
|
|
// appropriately set the pin logic according to setting for normal-high/normal-low operation
|
|
// and the probing cycle modes for toward-workpiece/away-from-workpiece.
|
|
void probe_configure_invert_mask(uint8_t is_probe_away)
|
|
{
|
|
probe_invert_mask = 0; // Initialize as zero.
|
|
if (bit_isfalse(settings.flags,BITFLAG_INVERT_PROBE_PIN)) { probe_invert_mask ^= PROBE_MASK; }
|
|
if (is_probe_away) { probe_invert_mask ^= PROBE_MASK; }
|
|
}
|
|
|
|
|
|
// Returns the probe pin state. Triggered = true. Called by gcode parser and probe state monitor.
|
|
uint8_t probe_get_state() { return((PROBE_PIN & PROBE_MASK) ^ probe_invert_mask); }
|
|
|
|
|
|
// Monitors probe pin state and records the system position when detected. Called by the
|
|
// stepper ISR per ISR tick.
|
|
// NOTE: This function must be extremely efficient as to not bog down the stepper ISR.
|
|
void probe_state_monitor()
|
|
{
|
|
if (sys_probe_state == PROBE_ACTIVE) {
|
|
if (probe_get_state()) {
|
|
sys_probe_state = PROBE_OFF;
|
|
memcpy(sys.probe_position, sys.position, sizeof(sys.position));
|
|
bit_true(sys_rt_exec_state, EXEC_MOTION_CANCEL);
|
|
}
|
|
}
|
|
}
|