490d3f1220
- [config] Permanently removed classic GUI interface support. This unintentionally created a problem where some users/GUI devs used this compatibility mode and did not update to the new interface. So, there were two interfaces in use, rather than just one like it was intended. This removal should help everyone by forcing all GUIs to update and updated GUI not having to support yet another interface. - Fixed typo with line number support in jog mode.
624 lines
23 KiB
C
624 lines
23 KiB
C
/*
|
|
report.c - reporting and messaging methods
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2012-2016 Sungeun K. Jeon for Gnea Research LLC
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/*
|
|
This file functions as the primary feedback interface for Grbl. Any outgoing data, such
|
|
as the protocol status messages, feedback messages, and status reports, are stored here.
|
|
For the most part, these functions primarily are called from protocol.c methods. If a
|
|
different style feedback is desired (i.e. JSON), then a user can change these following
|
|
methods to accomodate their needs.
|
|
*/
|
|
|
|
#include "grbl.h"
|
|
|
|
|
|
// Internal report utilities to reduce flash with repetitive tasks turned into functions.
|
|
void report_util_setting_prefix(uint8_t n) { serial_write('$'); print_uint8_base10(n); serial_write('='); }
|
|
static void report_util_line_feed() { printPgmString(PSTR("\r\n")); }
|
|
static void report_util_feedback_line_feed() { serial_write(']'); report_util_line_feed(); }
|
|
static void report_util_gcode_modes_G() { printPgmString(PSTR(" G")); }
|
|
static void report_util_gcode_modes_M() { printPgmString(PSTR(" M")); }
|
|
// static void report_util_comment_line_feed() { serial_write(')'); report_util_line_feed(); }
|
|
static void report_util_axis_values(float *axis_value) {
|
|
uint8_t idx;
|
|
for (idx=0; idx<N_AXIS; idx++) {
|
|
printFloat_CoordValue(axis_value[idx]);
|
|
if (idx < (N_AXIS-1)) { serial_write(','); }
|
|
}
|
|
}
|
|
|
|
/*
|
|
static void report_util_setting_string(uint8_t n) {
|
|
serial_write(' ');
|
|
serial_write('(');
|
|
switch(n) {
|
|
case 0: printPgmString(PSTR("stp pulse")); break;
|
|
case 1: printPgmString(PSTR("idl delay")); break;
|
|
case 2: printPgmString(PSTR("stp inv")); break;
|
|
case 3: printPgmString(PSTR("dir inv")); break;
|
|
case 4: printPgmString(PSTR("stp en inv")); break;
|
|
case 5: printPgmString(PSTR("lim inv")); break;
|
|
case 6: printPgmString(PSTR("prb inv")); break;
|
|
case 10: printPgmString(PSTR("rpt")); break;
|
|
case 11: printPgmString(PSTR("jnc dev")); break;
|
|
case 12: printPgmString(PSTR("arc tol")); break;
|
|
case 13: printPgmString(PSTR("rpt inch")); break;
|
|
case 20: printPgmString(PSTR("sft lim")); break;
|
|
case 21: printPgmString(PSTR("hrd lim")); break;
|
|
case 22: printPgmString(PSTR("hm cyc")); break;
|
|
case 23: printPgmString(PSTR("hm dir inv")); break;
|
|
case 24: printPgmString(PSTR("hm feed")); break;
|
|
case 25: printPgmString(PSTR("hm seek")); break;
|
|
case 26: printPgmString(PSTR("hm delay")); break;
|
|
case 27: printPgmString(PSTR("hm pulloff")); break;
|
|
case 30: printPgmString(PSTR("rpm max")); break;
|
|
case 31: printPgmString(PSTR("rpm min")); break;
|
|
case 32: printPgmString(PSTR("laser")); break;
|
|
default:
|
|
n -= AXIS_SETTINGS_START_VAL;
|
|
uint8_t idx = 0;
|
|
while (n >= AXIS_SETTINGS_INCREMENT) {
|
|
n -= AXIS_SETTINGS_INCREMENT;
|
|
idx++;
|
|
}
|
|
serial_write(n+'x');
|
|
switch (idx) {
|
|
case 0: printPgmString(PSTR(":stp/mm")); break;
|
|
case 1: printPgmString(PSTR(":mm/min")); break;
|
|
case 2: printPgmString(PSTR(":mm/s^2")); break;
|
|
case 3: printPgmString(PSTR(":mm max")); break;
|
|
}
|
|
break;
|
|
}
|
|
report_util_comment_line_feed();
|
|
}
|
|
*/
|
|
|
|
static void report_util_uint8_setting(uint8_t n, int val) {
|
|
report_util_setting_prefix(n);
|
|
print_uint8_base10(val);
|
|
report_util_line_feed(); // report_util_setting_string(n);
|
|
}
|
|
static void report_util_float_setting(uint8_t n, float val, uint8_t n_decimal) {
|
|
report_util_setting_prefix(n);
|
|
printFloat(val,n_decimal);
|
|
report_util_line_feed(); // report_util_setting_string(n);
|
|
}
|
|
|
|
|
|
// Handles the primary confirmation protocol response for streaming interfaces and human-feedback.
|
|
// For every incoming line, this method responds with an 'ok' for a successful command or an
|
|
// 'error:' to indicate some error event with the line or some critical system error during
|
|
// operation. Errors events can originate from the g-code parser, settings module, or asynchronously
|
|
// from a critical error, such as a triggered hard limit. Interface should always monitor for these
|
|
// responses.
|
|
// NOTE: In REPORT_GUI_MODE, all error codes are greater than zero.
|
|
void report_status_message(uint8_t status_code)
|
|
{
|
|
switch(status_code) {
|
|
case STATUS_OK: // STATUS_OK
|
|
printPgmString(PSTR("ok\r\n")); break;
|
|
default:
|
|
printPgmString(PSTR("error:"));
|
|
print_uint8_base10(status_code);
|
|
report_util_line_feed();
|
|
}
|
|
}
|
|
|
|
// Prints alarm messages.
|
|
void report_alarm_message(int8_t alarm_code)
|
|
{
|
|
printPgmString(PSTR("ALARM:"));
|
|
print_uint8_base10(alarm_code);
|
|
report_util_line_feed();
|
|
delay_ms(500); // Force delay to ensure message clears serial write buffer.
|
|
}
|
|
|
|
// Prints feedback messages. This serves as a centralized method to provide additional
|
|
// user feedback for things that are not of the status/alarm message protocol. These are
|
|
// messages such as setup warnings, switch toggling, and how to exit alarms.
|
|
// NOTE: For interfaces, messages are always placed within brackets. And if silent mode
|
|
// is installed, the message number codes are less than zero.
|
|
void report_feedback_message(uint8_t message_code)
|
|
{
|
|
printPgmString(PSTR("[MSG:"));
|
|
switch(message_code) {
|
|
case MESSAGE_CRITICAL_EVENT:
|
|
printPgmString(PSTR("Reset to continue")); break;
|
|
case MESSAGE_ALARM_LOCK:
|
|
printPgmString(PSTR("'$H'|'$X' to unlock")); break;
|
|
case MESSAGE_ALARM_UNLOCK:
|
|
printPgmString(PSTR("Caution: Unlocked")); break;
|
|
case MESSAGE_ENABLED:
|
|
printPgmString(PSTR("Enabled")); break;
|
|
case MESSAGE_DISABLED:
|
|
printPgmString(PSTR("Disabled")); break;
|
|
case MESSAGE_SAFETY_DOOR_AJAR:
|
|
printPgmString(PSTR("Check Door")); break;
|
|
case MESSAGE_CHECK_LIMITS:
|
|
printPgmString(PSTR("Check Limits")); break;
|
|
case MESSAGE_PROGRAM_END:
|
|
printPgmString(PSTR("Pgm End")); break;
|
|
case MESSAGE_RESTORE_DEFAULTS:
|
|
printPgmString(PSTR("Restoring defaults")); break;
|
|
case MESSAGE_SPINDLE_RESTORE:
|
|
printPgmString(PSTR("Restoring spindle")); break;
|
|
case MESSAGE_SLEEP_MODE:
|
|
printPgmString(PSTR("Sleeping")); break;
|
|
}
|
|
report_util_feedback_line_feed();
|
|
}
|
|
|
|
|
|
// Welcome message
|
|
void report_init_message()
|
|
{
|
|
printPgmString(PSTR("\r\nGrbl " GRBL_VERSION " ['$' for help]\r\n"));
|
|
}
|
|
|
|
// Grbl help message
|
|
void report_grbl_help() {
|
|
printPgmString(PSTR("[HLP:$$ $# $G $I $N $x=val $Nx=line $J=line $SLP $C $X $H ~ ! ? ctrl-x]\r\n"));
|
|
}
|
|
|
|
|
|
// Grbl global settings print out.
|
|
// NOTE: The numbering scheme here must correlate to storing in settings.c
|
|
void report_grbl_settings() {
|
|
// Print Grbl settings.
|
|
report_util_uint8_setting(0,settings.pulse_microseconds);
|
|
report_util_uint8_setting(1,settings.stepper_idle_lock_time);
|
|
report_util_uint8_setting(2,settings.step_invert_mask);
|
|
report_util_uint8_setting(3,settings.dir_invert_mask);
|
|
report_util_uint8_setting(4,bit_istrue(settings.flags,BITFLAG_INVERT_ST_ENABLE));
|
|
report_util_uint8_setting(5,bit_istrue(settings.flags,BITFLAG_INVERT_LIMIT_PINS));
|
|
report_util_uint8_setting(6,bit_istrue(settings.flags,BITFLAG_INVERT_PROBE_PIN));
|
|
report_util_uint8_setting(10,settings.status_report_mask);
|
|
report_util_float_setting(11,settings.junction_deviation,N_DECIMAL_SETTINGVALUE);
|
|
report_util_float_setting(12,settings.arc_tolerance,N_DECIMAL_SETTINGVALUE);
|
|
report_util_uint8_setting(13,bit_istrue(settings.flags,BITFLAG_REPORT_INCHES));
|
|
report_util_uint8_setting(20,bit_istrue(settings.flags,BITFLAG_SOFT_LIMIT_ENABLE));
|
|
report_util_uint8_setting(21,bit_istrue(settings.flags,BITFLAG_HARD_LIMIT_ENABLE));
|
|
report_util_uint8_setting(22,bit_istrue(settings.flags,BITFLAG_HOMING_ENABLE));
|
|
report_util_uint8_setting(23,settings.homing_dir_mask);
|
|
report_util_float_setting(24,settings.homing_feed_rate,N_DECIMAL_SETTINGVALUE);
|
|
report_util_float_setting(25,settings.homing_seek_rate,N_DECIMAL_SETTINGVALUE);
|
|
report_util_uint8_setting(26,settings.homing_debounce_delay);
|
|
report_util_float_setting(27,settings.homing_pulloff,N_DECIMAL_SETTINGVALUE);
|
|
report_util_float_setting(30,settings.rpm_max,N_DECIMAL_RPMVALUE);
|
|
report_util_float_setting(31,settings.rpm_min,N_DECIMAL_RPMVALUE);
|
|
#ifdef VARIABLE_SPINDLE
|
|
report_util_uint8_setting(32,bit_istrue(settings.flags,BITFLAG_LASER_MODE));
|
|
#else
|
|
report_util_uint8_setting(32,0);
|
|
#endif
|
|
// Print axis settings
|
|
uint8_t idx, set_idx;
|
|
uint8_t val = AXIS_SETTINGS_START_VAL;
|
|
for (set_idx=0; set_idx<AXIS_N_SETTINGS; set_idx++) {
|
|
for (idx=0; idx<N_AXIS; idx++) {
|
|
switch (set_idx) {
|
|
case 0: report_util_float_setting(val+idx,settings.steps_per_mm[idx],N_DECIMAL_SETTINGVALUE); break;
|
|
case 1: report_util_float_setting(val+idx,settings.max_rate[idx],N_DECIMAL_SETTINGVALUE); break;
|
|
case 2: report_util_float_setting(val+idx,settings.acceleration[idx]/(60*60),N_DECIMAL_SETTINGVALUE); break;
|
|
case 3: report_util_float_setting(val+idx,-settings.max_travel[idx],N_DECIMAL_SETTINGVALUE); break;
|
|
}
|
|
}
|
|
val += AXIS_SETTINGS_INCREMENT;
|
|
}
|
|
}
|
|
|
|
|
|
// Prints current probe parameters. Upon a probe command, these parameters are updated upon a
|
|
// successful probe or upon a failed probe with the G38.3 without errors command (if supported).
|
|
// These values are retained until Grbl is power-cycled, whereby they will be re-zeroed.
|
|
void report_probe_parameters()
|
|
{
|
|
// Report in terms of machine position.
|
|
printPgmString(PSTR("[PRB:"));
|
|
float print_position[N_AXIS];
|
|
system_convert_array_steps_to_mpos(print_position,sys_probe_position);
|
|
report_util_axis_values(print_position);
|
|
serial_write(':');
|
|
print_uint8_base10(sys.probe_succeeded);
|
|
report_util_feedback_line_feed();
|
|
}
|
|
|
|
|
|
// Prints Grbl NGC parameters (coordinate offsets, probing)
|
|
void report_ngc_parameters()
|
|
{
|
|
float coord_data[N_AXIS];
|
|
uint8_t coord_select;
|
|
for (coord_select = 0; coord_select <= SETTING_INDEX_NCOORD; coord_select++) {
|
|
if (!(settings_read_coord_data(coord_select,coord_data))) {
|
|
report_status_message(STATUS_SETTING_READ_FAIL);
|
|
return;
|
|
}
|
|
printPgmString(PSTR("[G"));
|
|
switch (coord_select) {
|
|
case 6: printPgmString(PSTR("28")); break;
|
|
case 7: printPgmString(PSTR("30")); break;
|
|
default: print_uint8_base10(coord_select+54); break; // G54-G59
|
|
}
|
|
serial_write(':');
|
|
report_util_axis_values(coord_data);
|
|
report_util_feedback_line_feed();
|
|
}
|
|
printPgmString(PSTR("[G92:")); // Print G92,G92.1 which are not persistent in memory
|
|
report_util_axis_values(gc_state.coord_offset);
|
|
report_util_feedback_line_feed();
|
|
printPgmString(PSTR("[TLO:")); // Print tool length offset value
|
|
printFloat_CoordValue(gc_state.tool_length_offset);
|
|
report_util_feedback_line_feed();
|
|
report_probe_parameters(); // Print probe parameters. Not persistent in memory.
|
|
}
|
|
|
|
|
|
// Print current gcode parser mode state
|
|
void report_gcode_modes()
|
|
{
|
|
printPgmString(PSTR("[GC:G"));
|
|
if (gc_state.modal.motion >= MOTION_MODE_PROBE_TOWARD) {
|
|
printPgmString(PSTR("38."));
|
|
print_uint8_base10(gc_state.modal.motion - (MOTION_MODE_PROBE_TOWARD-2));
|
|
} else {
|
|
print_uint8_base10(gc_state.modal.motion);
|
|
}
|
|
|
|
report_util_gcode_modes_G();
|
|
print_uint8_base10(gc_state.modal.coord_select+54);
|
|
|
|
report_util_gcode_modes_G();
|
|
print_uint8_base10(gc_state.modal.plane_select+17);
|
|
|
|
report_util_gcode_modes_G();
|
|
print_uint8_base10(21-gc_state.modal.units);
|
|
|
|
report_util_gcode_modes_G();
|
|
print_uint8_base10(gc_state.modal.distance+90);
|
|
|
|
report_util_gcode_modes_G();
|
|
print_uint8_base10(94-gc_state.modal.feed_rate);
|
|
|
|
if (gc_state.modal.program_flow) {
|
|
report_util_gcode_modes_M();
|
|
switch (gc_state.modal.program_flow) {
|
|
case PROGRAM_FLOW_PAUSED : serial_write('0'); break;
|
|
// case PROGRAM_FLOW_OPTIONAL_STOP : serial_write('1'); break; // M1 is ignored and not supported.
|
|
case PROGRAM_FLOW_COMPLETED_M2 :
|
|
case PROGRAM_FLOW_COMPLETED_M30 :
|
|
print_uint8_base10(gc_state.modal.program_flow);
|
|
break;
|
|
}
|
|
}
|
|
|
|
report_util_gcode_modes_M();
|
|
switch (gc_state.modal.spindle) {
|
|
case SPINDLE_ENABLE_CW : serial_write('3'); break;
|
|
case SPINDLE_ENABLE_CCW : serial_write('4'); break;
|
|
case SPINDLE_DISABLE : serial_write('5'); break;
|
|
}
|
|
|
|
report_util_gcode_modes_M();
|
|
#ifdef ENABLE_M7
|
|
if (gc_state.modal.coolant) { // Note: Multiple coolant states may be active at the same time.
|
|
if (gc_state.modal.coolant & PL_COND_FLAG_COOLANT_MIST) { serial_write('7'); }
|
|
if (gc_state.modal.coolant & PL_COND_FLAG_COOLANT_FLOOD) { serial_write('8'); }
|
|
} else { serial_write('9'); }
|
|
#else
|
|
if (gc_state.modal.coolant) { serial_write('8'); }
|
|
else { serial_write('9'); }
|
|
#endif
|
|
|
|
printPgmString(PSTR(" T"));
|
|
print_uint8_base10(gc_state.tool);
|
|
|
|
printPgmString(PSTR(" F"));
|
|
printFloat_RateValue(gc_state.feed_rate);
|
|
|
|
#ifdef VARIABLE_SPINDLE
|
|
printPgmString(PSTR(" S"));
|
|
printFloat(gc_state.spindle_speed,N_DECIMAL_RPMVALUE);
|
|
#endif
|
|
|
|
report_util_feedback_line_feed();
|
|
}
|
|
|
|
// Prints specified startup line
|
|
void report_startup_line(uint8_t n, char *line)
|
|
{
|
|
printPgmString(PSTR("$N"));
|
|
print_uint8_base10(n);
|
|
serial_write('=');
|
|
printString(line);
|
|
report_util_line_feed();
|
|
}
|
|
|
|
void report_execute_startup_message(char *line, uint8_t status_code)
|
|
{
|
|
serial_write('>');
|
|
printString(line);
|
|
serial_write(':');
|
|
report_status_message(status_code);
|
|
}
|
|
|
|
// Prints build info line
|
|
void report_build_info(char *line)
|
|
{
|
|
printPgmString(PSTR("[VER:" GRBL_VERSION "." GRBL_VERSION_BUILD ":"));
|
|
printString(line);
|
|
report_util_feedback_line_feed();
|
|
printPgmString(PSTR("[OPT:")); // Generate compile-time build option list
|
|
#ifdef VARIABLE_SPINDLE
|
|
serial_write('V');
|
|
#endif
|
|
#ifdef USE_LINE_NUMBERS
|
|
serial_write('N');
|
|
#endif
|
|
#ifdef ENABLE_M7
|
|
serial_write('M');
|
|
#endif
|
|
#ifdef COREXY
|
|
serial_write('C');
|
|
#endif
|
|
#ifdef PARKING_ENABLE
|
|
serial_write('P');
|
|
#endif
|
|
#ifdef HOMING_FORCE_SET_ORIGIN
|
|
serial_write('Z');
|
|
#endif
|
|
#ifdef HOMING_SINGLE_AXIS_COMMANDS
|
|
serial_write('H');
|
|
#endif
|
|
#ifdef LIMITS_TWO_SWITCHES_ON_AXES
|
|
serial_write('L');
|
|
#endif
|
|
#ifdef ALLOW_FEED_OVERRIDE_DURING_PROBE_CYCLES
|
|
serial_write('A');
|
|
#endif
|
|
#ifdef USE_CLASSIC_GRBL_INTERFACE
|
|
serial_write('R');
|
|
#endif
|
|
#ifndef ENABLE_RESTORE_EEPROM_WIPE_ALL // NOTE: Shown when disabled.
|
|
serial_write('*');
|
|
#endif
|
|
#ifndef ENABLE_RESTORE_EEPROM_DEFAULT_SETTINGS // NOTE: Shown when disabled.
|
|
serial_write('$');
|
|
#endif
|
|
#ifndef ENABLE_RESTORE_EEPROM_CLEAR_PARAMETERS // NOTE: Shown when disabled.
|
|
serial_write('#');
|
|
#endif
|
|
#ifndef ENABLE_BUILD_INFO_WRITE_COMMAND // NOTE: Shown when disabled.
|
|
serial_write('I');
|
|
#endif
|
|
#ifndef FORCE_BUFFER_SYNC_DURING_EEPROM_WRITE // NOTE: Shown when disabled.
|
|
serial_write('E');
|
|
#endif
|
|
#ifndef FORCE_BUFFER_SYNC_DURING_WCO_CHANGE // NOTE: Shown when disabled.
|
|
serial_write('W');
|
|
#endif
|
|
// NOTE: Compiled values, like override increments/max/min values, may be added at some point later.
|
|
// These will likely have a comma delimiter to separate them.
|
|
|
|
report_util_feedback_line_feed();
|
|
}
|
|
|
|
|
|
// Prints the character string line Grbl has received from the user, which has been pre-parsed,
|
|
// and has been sent into protocol_execute_line() routine to be executed by Grbl.
|
|
void report_echo_line_received(char *line)
|
|
{
|
|
printPgmString(PSTR("[echo: ")); printString(line);
|
|
report_util_feedback_line_feed();
|
|
}
|
|
|
|
|
|
// Prints real-time data. This function grabs a real-time snapshot of the stepper subprogram
|
|
// and the actual location of the CNC machine. Users may change the following function to their
|
|
// specific needs, but the desired real-time data report must be as short as possible. This is
|
|
// requires as it minimizes the computational overhead and allows grbl to keep running smoothly,
|
|
// especially during g-code programs with fast, short line segments and high frequency reports (5-20Hz).
|
|
void report_realtime_status()
|
|
{
|
|
uint8_t idx;
|
|
int32_t current_position[N_AXIS]; // Copy current state of the system position variable
|
|
memcpy(current_position,sys_position,sizeof(sys_position));
|
|
float print_position[N_AXIS];
|
|
system_convert_array_steps_to_mpos(print_position,current_position);
|
|
|
|
// Report current machine state and sub-states
|
|
serial_write('<');
|
|
switch (sys.state) {
|
|
case STATE_IDLE: printPgmString(PSTR("Idle")); break;
|
|
case STATE_CYCLE: printPgmString(PSTR("Run")); break;
|
|
case STATE_HOLD:
|
|
if (!(sys.suspend & SUSPEND_JOG_CANCEL)) {
|
|
printPgmString(PSTR("Hold:"));
|
|
if (sys.suspend & SUSPEND_HOLD_COMPLETE) { serial_write('0'); } // Ready to resume
|
|
else { serial_write('1'); } // Actively holding
|
|
break;
|
|
} // Continues to print jog state during jog cancel.
|
|
case STATE_JOG: printPgmString(PSTR("Jog")); break;
|
|
case STATE_HOMING: printPgmString(PSTR("Home")); break;
|
|
case STATE_ALARM: printPgmString(PSTR("Alarm")); break;
|
|
case STATE_CHECK_MODE: printPgmString(PSTR("Check")); break;
|
|
case STATE_SAFETY_DOOR:
|
|
printPgmString(PSTR("Door:"));
|
|
if (sys.suspend & SUSPEND_INITIATE_RESTORE) {
|
|
serial_write('3'); // Restoring
|
|
} else {
|
|
if (sys.suspend & SUSPEND_RETRACT_COMPLETE) {
|
|
if (sys.suspend & SUSPEND_SAFETY_DOOR_AJAR) {
|
|
serial_write('1'); // Door ajar
|
|
} else {
|
|
serial_write('0');
|
|
} // Door closed and ready to resume
|
|
} else {
|
|
serial_write('2'); // Retracting
|
|
}
|
|
}
|
|
break;
|
|
case STATE_SLEEP: printPgmString(PSTR("Sleep")); break;
|
|
}
|
|
|
|
float wco[N_AXIS];
|
|
if (bit_isfalse(settings.status_report_mask,BITFLAG_RT_STATUS_POSITION_TYPE) ||
|
|
(sys.report_wco_counter == 0) ) {
|
|
for (idx=0; idx< N_AXIS; idx++) {
|
|
// Apply work coordinate offsets and tool length offset to current position.
|
|
wco[idx] = gc_state.coord_system[idx]+gc_state.coord_offset[idx];
|
|
if (idx == TOOL_LENGTH_OFFSET_AXIS) { wco[idx] += gc_state.tool_length_offset; }
|
|
if (bit_isfalse(settings.status_report_mask,BITFLAG_RT_STATUS_POSITION_TYPE)) {
|
|
print_position[idx] -= wco[idx];
|
|
}
|
|
}
|
|
}
|
|
|
|
// Report machine position
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_POSITION_TYPE)) {
|
|
printPgmString(PSTR("|MPos:"));
|
|
} else {
|
|
printPgmString(PSTR("|WPos:"));
|
|
}
|
|
report_util_axis_values(print_position);
|
|
|
|
// Returns planner and serial read buffer states.
|
|
#ifdef REPORT_FIELD_BUFFER_STATE
|
|
if (bit_istrue(settings.status_report_mask,BITFLAG_RT_STATUS_BUFFER_STATE)) {
|
|
printPgmString(PSTR("|Bf:"));
|
|
print_uint8_base10(plan_get_block_buffer_available());
|
|
serial_write(',');
|
|
print_uint8_base10(serial_get_rx_buffer_available());
|
|
}
|
|
#endif
|
|
|
|
#ifdef USE_LINE_NUMBERS
|
|
#ifdef REPORT_FIELD_LINE_NUMBERS
|
|
// Report current line number
|
|
plan_block_t * cur_block = plan_get_current_block();
|
|
if (cur_block != NULL) {
|
|
uint32_t ln = cur_block->line_number;
|
|
if (ln > 0) {
|
|
printPgmString(PSTR("|Ln:"));
|
|
printInteger(ln);
|
|
}
|
|
}
|
|
#endif
|
|
#endif
|
|
|
|
// Report realtime feed speed
|
|
#ifdef REPORT_FIELD_CURRENT_FEED_SPEED
|
|
#ifdef VARIABLE_SPINDLE
|
|
printPgmString(PSTR("|FS:"));
|
|
printFloat_RateValue(st_get_realtime_rate());
|
|
serial_write(',');
|
|
printFloat(sys.spindle_speed,N_DECIMAL_RPMVALUE);
|
|
#else
|
|
printPgmString(PSTR("|F:"));
|
|
printFloat_RateValue(st_get_realtime_rate());
|
|
#endif
|
|
#endif
|
|
|
|
#ifdef REPORT_FIELD_PIN_STATE
|
|
uint8_t lim_pin_state = limits_get_state();
|
|
uint8_t ctrl_pin_state = system_control_get_state();
|
|
uint8_t prb_pin_state = probe_get_state();
|
|
if (lim_pin_state | ctrl_pin_state | prb_pin_state) {
|
|
printPgmString(PSTR("|Pn:"));
|
|
if (prb_pin_state) { serial_write('P'); }
|
|
if (lim_pin_state) {
|
|
if (bit_istrue(lim_pin_state,bit(X_AXIS))) { serial_write('X'); }
|
|
if (bit_istrue(lim_pin_state,bit(Y_AXIS))) { serial_write('Y'); }
|
|
if (bit_istrue(lim_pin_state,bit(Z_AXIS))) { serial_write('Z'); }
|
|
}
|
|
if (ctrl_pin_state) {
|
|
#ifdef ENABLE_SAFETY_DOOR_INPUT_PIN
|
|
if (bit_istrue(ctrl_pin_state,CONTROL_PIN_INDEX_SAFETY_DOOR)) { serial_write('D'); }
|
|
#endif
|
|
if (bit_istrue(ctrl_pin_state,CONTROL_PIN_INDEX_RESET)) { serial_write('R'); }
|
|
if (bit_istrue(ctrl_pin_state,CONTROL_PIN_INDEX_FEED_HOLD)) { serial_write('H'); }
|
|
if (bit_istrue(ctrl_pin_state,CONTROL_PIN_INDEX_CYCLE_START)) { serial_write('S'); }
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#ifdef REPORT_FIELD_WORK_COORD_OFFSET
|
|
if (sys.report_wco_counter > 0) { sys.report_wco_counter--; }
|
|
else {
|
|
if (sys.state & (STATE_HOMING | STATE_CYCLE | STATE_HOLD | STATE_JOG | STATE_SAFETY_DOOR)) {
|
|
sys.report_wco_counter = (REPORT_WCO_REFRESH_BUSY_COUNT-1); // Reset counter for slow refresh
|
|
} else { sys.report_wco_counter = (REPORT_WCO_REFRESH_IDLE_COUNT-1); }
|
|
if (sys.report_ovr_counter == 0) { sys.report_ovr_counter = 1; } // Set override on next report.
|
|
printPgmString(PSTR("|WCO:"));
|
|
report_util_axis_values(wco);
|
|
}
|
|
#endif
|
|
|
|
#ifdef REPORT_FIELD_OVERRIDES
|
|
if (sys.report_ovr_counter > 0) { sys.report_ovr_counter--; }
|
|
else {
|
|
if (sys.state & (STATE_HOMING | STATE_CYCLE | STATE_HOLD | STATE_JOG | STATE_SAFETY_DOOR)) {
|
|
sys.report_ovr_counter = (REPORT_OVR_REFRESH_BUSY_COUNT-1); // Reset counter for slow refresh
|
|
} else { sys.report_ovr_counter = (REPORT_OVR_REFRESH_IDLE_COUNT-1); }
|
|
printPgmString(PSTR("|Ov:"));
|
|
print_uint8_base10(sys.f_override);
|
|
serial_write(',');
|
|
print_uint8_base10(sys.r_override);
|
|
serial_write(',');
|
|
print_uint8_base10(sys.spindle_speed_ovr);
|
|
|
|
uint8_t sp_state = spindle_get_state();
|
|
uint8_t cl_state = coolant_get_state();
|
|
if (sp_state || cl_state) {
|
|
printPgmString(PSTR("|A:"));
|
|
if (sp_state) { // != SPINDLE_STATE_DISABLE
|
|
#ifdef VARIABLE_SPINDLE
|
|
#ifdef USE_SPINDLE_DIR_AS_ENABLE_PIN
|
|
serial_write('S'); // CW
|
|
#else
|
|
if (sp_state == SPINDLE_STATE_CW) { serial_write('S'); } // CW
|
|
else { serial_write('C'); } // CCW
|
|
#endif
|
|
#else
|
|
if (sp_state & SPINDLE_STATE_CW) { serial_write('S'); } // CW
|
|
else { serial_write('C'); } // CCW
|
|
#endif
|
|
}
|
|
if (cl_state & COOLANT_STATE_FLOOD) { serial_write('F'); }
|
|
#ifdef ENABLE_M7
|
|
if (cl_state & COOLANT_STATE_MIST) { serial_write('M'); }
|
|
#endif
|
|
}
|
|
}
|
|
#endif
|
|
|
|
serial_write('>');
|
|
report_util_line_feed();
|
|
}
|
|
|
|
|
|
#ifdef DEBUG
|
|
void report_realtime_debug()
|
|
{
|
|
|
|
}
|
|
#endif
|