d85238cc9b
- The homing sequence is now a compile-time option, where a user can choose which axes(s) move in sequence during the search phase. Up to 3 sequences. Works with the locating phase and the pull-off maneuver. - New defaults.h file to store user generated default settings for different machines. Mainly to be used as a central repo, but each set may be select to be compiled in as a config.h define.
235 lines
14 KiB
C
Executable File
235 lines
14 KiB
C
Executable File
/*
|
|
config.h - compile time configuration
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2009-2011 Simen Svale Skogsrud
|
|
Copyright (c) 2011-2012 Sungeun K. Jeon
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#ifndef config_h
|
|
#define config_h
|
|
|
|
// IMPORTANT: Any changes here requires a full re-compiling of the source code to propagate them.
|
|
|
|
// Default settings. Used when resetting EEPROM. Change to desired name in defaults.h
|
|
#define DEFAULTS_GENERIC
|
|
|
|
// Serial baud rate
|
|
#define BAUD_RATE 9600
|
|
|
|
// Define pin-assignments
|
|
// NOTE: All step bit and direction pins must be on the same port.
|
|
#define STEPPING_DDR DDRD
|
|
#define STEPPING_PORT PORTD
|
|
#define X_STEP_BIT 2 // Uno Digital Pin 2
|
|
#define Y_STEP_BIT 3 // Uno Digital Pin 3
|
|
#define Z_STEP_BIT 4 // Uno Digital Pin 4
|
|
#define X_DIRECTION_BIT 5 // Uno Digital Pin 5
|
|
#define Y_DIRECTION_BIT 6 // Uno Digital Pin 6
|
|
#define Z_DIRECTION_BIT 7 // Uno Digital Pin 7
|
|
#define STEP_MASK ((1<<X_STEP_BIT)|(1<<Y_STEP_BIT)|(1<<Z_STEP_BIT)) // All step bits
|
|
#define DIRECTION_MASK ((1<<X_DIRECTION_BIT)|(1<<Y_DIRECTION_BIT)|(1<<Z_DIRECTION_BIT)) // All direction bits
|
|
#define STEPPING_MASK (STEP_MASK | DIRECTION_MASK) // All stepping-related bits (step/direction)
|
|
|
|
#define STEPPERS_DISABLE_DDR DDRB
|
|
#define STEPPERS_DISABLE_PORT PORTB
|
|
#define STEPPERS_DISABLE_BIT 0 // Uno Digital Pin 8
|
|
#define STEPPERS_DISABLE_MASK (1<<STEPPERS_DISABLE_BIT)
|
|
|
|
// NOTE: All limit bit pins must be on the same port
|
|
#define LIMIT_DDR DDRB
|
|
#define LIMIT_PIN PINB
|
|
#define LIMIT_PORT PORTB
|
|
#define X_LIMIT_BIT 1 // Uno Digital Pin 9
|
|
#define Y_LIMIT_BIT 2 // Uno Digital Pin 10
|
|
#define Z_LIMIT_BIT 3 // Uno Digital Pin 11
|
|
#define LIMIT_INT PCIE0 // Pin change interrupt enable pin
|
|
#define LIMIT_INT_vect PCINT0_vect
|
|
#define LIMIT_PCMSK PCMSK0 // Pin change interrupt register
|
|
#define LIMIT_MASK ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)) // All limit bits
|
|
|
|
#define SPINDLE_ENABLE_DDR DDRB
|
|
#define SPINDLE_ENABLE_PORT PORTB
|
|
#define SPINDLE_ENABLE_BIT 4 // Uno Digital Pin 12
|
|
|
|
#define SPINDLE_DIRECTION_DDR DDRB
|
|
#define SPINDLE_DIRECTION_PORT PORTB
|
|
#define SPINDLE_DIRECTION_BIT 5 // Uno Digital Pin 13 (NOTE: D13 can't be pulled-high input due to LED.)
|
|
|
|
#define COOLANT_FLOOD_DDR DDRC
|
|
#define COOLANT_FLOOD_PORT PORTC
|
|
#define COOLANT_FLOOD_BIT 3 // Uno Analog Pin 3
|
|
|
|
// NOTE: Uno analog pins 4 and 5 are reserved for an i2c interface, and may be installed at
|
|
// a later date if flash and memory space allows.
|
|
// #define ENABLE_M7 // Mist coolant disabled by default. Uncomment to enable.
|
|
#ifdef ENABLE_M7
|
|
#define COOLANT_MIST_DDR DDRC
|
|
#define COOLANT_MIST_PORT PORTC
|
|
#define COOLANT_MIST_BIT 4 // Uno Analog Pin 4
|
|
#endif
|
|
|
|
// NOTE: All pinouts pins must be on the same port
|
|
#define PINOUT_DDR DDRC
|
|
#define PINOUT_PIN PINC
|
|
#define PINOUT_PORT PORTC
|
|
#define PIN_RESET 0 // Uno Analog Pin 0
|
|
#define PIN_FEED_HOLD 1 // Uno Analog Pin 1
|
|
#define PIN_CYCLE_START 2 // Uno Analog Pin 2
|
|
#define PINOUT_INT PCIE1 // Pin change interrupt enable pin
|
|
#define PINOUT_INT_vect PCINT1_vect
|
|
#define PINOUT_PCMSK PCMSK1 // Pin change interrupt register
|
|
#define PINOUT_MASK ((1<<PIN_RESET)|(1<<PIN_FEED_HOLD)|(1<<PIN_CYCLE_START))
|
|
|
|
// Define runtime command special characters. These characters are 'picked-off' directly from the
|
|
// serial read data stream and are not passed to the grbl line execution parser. Select characters
|
|
// that do not and must not exist in the streamed g-code program. ASCII control characters may be
|
|
// used, if they are available per user setup. Also, extended ASCII codes (>127), which are never in
|
|
// g-code programs, maybe selected for interface programs.
|
|
// NOTE: If changed, manually update help message in report.c.
|
|
#define CMD_STATUS_REPORT '?'
|
|
#define CMD_FEED_HOLD '!'
|
|
#define CMD_CYCLE_START '~'
|
|
#define CMD_RESET 0x18 // ctrl-x
|
|
|
|
// The temporal resolution of the acceleration management subsystem. Higher number give smoother
|
|
// acceleration but may impact performance.
|
|
// NOTE: Increasing this parameter will help any resolution related issues, especially with machines
|
|
// requiring very high accelerations and/or very fast feedrates. In general, this will reduce the
|
|
// error between how the planner plans the motions and how the stepper program actually performs them.
|
|
// However, at some point, the resolution can be high enough, where the errors related to numerical
|
|
// round-off can be great enough to cause problems and/or it's too fast for the Arduino. The correct
|
|
// value for this parameter is machine dependent, so it's advised to set this only as high as needed.
|
|
// Approximate successful values can range from 30L to 100L or more.
|
|
#define ACCELERATION_TICKS_PER_SECOND 50L
|
|
|
|
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
|
|
// of the buffer and all stops. This should not be much greater than zero and should only be changed
|
|
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
|
|
#define MINIMUM_PLANNER_SPEED 0.0 // (mm/min)
|
|
|
|
// Minimum stepper rate. Sets the absolute minimum stepper rate in the stepper program and never runs
|
|
// slower than this value, except when sleeping. This parameter overrides the minimum planner speed.
|
|
// This is primarily used to guarantee that the end of a movement is always reached and not stop to
|
|
// never reach its target. This parameter should always be greater than zero.
|
|
#define MINIMUM_STEPS_PER_MINUTE 800 // (steps/min) - Integer value only
|
|
|
|
// Time delay increments performed during a dwell. The default value is set at 50ms, which provides
|
|
// a maximum time delay of roughly 55 minutes, more than enough for most any application. Increasing
|
|
// this delay will increase the maximum dwell time linearly, but also reduces the responsiveness of
|
|
// run-time command executions, like status reports, since these are performed between each dwell
|
|
// time step. Also, keep in mind that the Arduino delay timer is not very accurate for long delays.
|
|
#define DWELL_TIME_STEP 50 // Integer (1-255) (milliseconds)
|
|
|
|
// If homing is enabled, homing init lock sets Grbl into an alarm state upon power up. This forces
|
|
// the user to perform the homing cycle (or override the locks) before doing anything else. This is
|
|
// mainly a safety feature to remind the user to home, since position is unknown to Grbl.
|
|
#define HOMING_INIT_LOCK // Comment to disable
|
|
|
|
// The homing cycle seek and feed rates will adjust so all axes independently move at the homing
|
|
// seek and feed rates regardless of how many axes are in motion simultaneously. If disabled, rates
|
|
// are point-to-point rates, as done in normal operation. For example in an XY diagonal motion, the
|
|
// diagonal motion moves at the intended rate, but the individual axes move at 70% speed. This option
|
|
// just moves them all at 100% speed.
|
|
#define HOMING_RATE_ADJUST // Comment to disable
|
|
|
|
// Define the homing cycle search patterns with bitmasks. The homing cycle first performs a search
|
|
// to engage the limit switches. HOMING_SEARCH_CYCLE_x are executed in order starting with suffix 0
|
|
// and searches the enabled axes in the bitmask. This allows for users with non-standard cartesian
|
|
// machines, such as a lathe (x then z), to configure the homing cycle behavior to their needs.
|
|
// Search cycle 0 is required, but cycles 1 and 2 are both optional and may be commented to disable.
|
|
// After the search cycle, homing then performs a series of locating about the limit switches to hone
|
|
// in on machine zero, followed by a pull-off maneuver. HOMING_LOCATE_CYCLE governs these final moves,
|
|
// and this mask must contain all axes in the search.
|
|
// NOTE: Later versions may have this installed in settings.
|
|
#define HOMING_SEARCH_CYCLE_0 (1<<Z_AXIS) // First move Z to clear workspace.
|
|
#define HOMING_SEARCH_CYCLE_1 ((1<<X_AXIS)|(1<<Y_AXIS)) // Then move X,Y at the same time.
|
|
// #define HOMING_SEARCH_CYCLE_2 // Uncomment and add axes mask to enable
|
|
#define HOMING_LOCATE_CYCLE ((1<<X_AXIS)|(1<<Y_AXIS)|(1<<Z_AXIS)) // Must contain ALL search axes
|
|
|
|
// Number of homing cycles performed after when the machine initially jogs to limit switches.
|
|
// This help in preventing overshoot and should improve repeatability. This value should be one or
|
|
// greater.
|
|
#define N_HOMING_LOCATE_CYCLE 2 // Integer (1-128)
|
|
|
|
// Number of blocks Grbl executes upon startup. These blocks are stored in EEPROM, where the size
|
|
// and addresses are defined in settings.h. With the current settings, up to 5 startup blocks may
|
|
// be stored and executed in order. These startup blocks would typically be used to set the g-code
|
|
// parser state depending on user preferences.
|
|
#define N_STARTUP_LINE 2 // Integer (1-5)
|
|
|
|
// ---------------------------------------------------------------------------------------
|
|
// FOR ADVANCED USERS ONLY:
|
|
|
|
// The number of linear motions in the planner buffer to be planned at any give time. The vast
|
|
// majority of RAM that Grbl uses is based on this buffer size. Only increase if there is extra
|
|
// available RAM, like when re-compiling for a Teensy or Sanguino. Or decrease if the Arduino
|
|
// begins to crash due to the lack of available RAM or if the CPU is having trouble keeping
|
|
// up with planning new incoming motions as they are executed.
|
|
// #define BLOCK_BUFFER_SIZE 18 // Uncomment to override default in planner.h.
|
|
|
|
// Line buffer size from the serial input stream to be executed. Also, governs the size of
|
|
// each of the startup blocks, as they are each stored as a string of this size. Make sure
|
|
// to account for the available EEPROM at the defined memory address in settings.h and for
|
|
// the number of desired startup blocks.
|
|
// NOTE: 50 characters is not a problem except for extreme cases, but the line buffer size
|
|
// can be too small and g-code blocks can get truncated. Officially, the g-code standards
|
|
// support up to 256 characters. In future versions, this default will be increased, when
|
|
// we know how much extra memory space we can re-invest into this.
|
|
// #define LINE_BUFFER_SIZE 50 // Uncomment to override default in protocol.h
|
|
|
|
// Serial send and receive buffer size. The receive buffer is often used as another streaming
|
|
// buffer to store incoming blocks to be processed by Grbl when its ready. Most streaming
|
|
// interfaces will character count and track each block send to each block response. So,
|
|
// increase the receive buffer if a deeper receive buffer is needed for streaming and avaiable
|
|
// memory allows. The send buffer primarily handles messages in Grbl. Only increase if large
|
|
// messages are sent and Grbl begins to stall, waiting to send the rest of the message.
|
|
// #define RX_BUFFER_SIZE 128 // Uncomment to override defaults in serial.h
|
|
// #define TX_BUFFER_SIZE 64
|
|
|
|
// Toggles XON/XOFF software flow control for serial communications. Not officially supported
|
|
// due to problems involving the Atmega8U2 USB-to-serial chips on current Arduinos. The firmware
|
|
// on these chips do not support XON/XOFF flow control characters and the intermediate buffer
|
|
// in the chips cause latency and overflow problems with standard terminal programs. However,
|
|
// using specifically-programmed UI's to manage this latency problem has been confirmed to work.
|
|
// As well as, older FTDI FT232RL-based Arduinos(Duemilanove) are known to work with standard
|
|
// terminal programs since their firmware correctly manage these XON/XOFF characters. In any
|
|
// case, please report any successes to grbl administrators!
|
|
// #define ENABLE_XONXOFF // Default disabled. Uncomment to enable.
|
|
|
|
// Creates a delay between the direction pin setting and corresponding step pulse by creating
|
|
// another interrupt (Timer2 compare) to manage it. The main Grbl interrupt (Timer1 compare)
|
|
// sets the direction pins, and does not immediately set the stepper pins, as it would in
|
|
// normal operation. The Timer2 compare fires next to set the stepper pins after the step
|
|
// pulse delay time, and Timer2 overflow will complete the step pulse, except now delayed
|
|
// by the step pulse time plus the step pulse delay. (Thanks langwadt for the idea!)
|
|
// This is an experimental feature that should only be used if your setup requires a longer
|
|
// delay between direction and step pin settings (some opto coupler based drivers), as it may
|
|
// adversely effect Grbl's high-end performance (>10kHz). Please notify Grbl administrators
|
|
// of your successes or difficulties, as we will monitor this and possibly integrate this as a
|
|
// standard feature for future releases. However, we suggest to first try our direction delay
|
|
// hack/solution posted in the Wiki involving inverting the stepper pin mask.
|
|
// NOTE: Uncomment to enable. The recommended delay must be > 3us and the total step pulse
|
|
// time, which includes the Grbl settings pulse microseconds, must not exceed 127us. Reported
|
|
// successful values for certain setups have ranged from 10 to 20us.
|
|
// #define STEP_PULSE_DELAY 10 // Step pulse delay in microseconds. Default disabled.
|
|
|
|
// ---------------------------------------------------------------------------------------
|
|
|
|
// TODO: Install compile-time option to send numeric status codes rather than strings.
|
|
|
|
#endif
|