7a175bd2db
- **NON-FUNCTIONAL** - Contains an old draft of separating the stepper driver direct access to the planner buffer. This is designed to keep the stepper and planner modules independent and prevent overwriting or other complications. In this way, feedrate override should be able to be installed as well. - A number of planner optimizations are installed too. - Not sure where the bugs are. Either in the new planner optimizations, new stepper module updates, or in both. Or it just could be that the Arduino AVR is choking with the new things it has to do.
115 lines
4.4 KiB
C
115 lines
4.4 KiB
C
/*
|
|
main.c - An embedded CNC Controller with rs274/ngc (g-code) support
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2009-2011 Simen Svale Skogsrud
|
|
Copyright (c) 2011-2013 Sungeun K. Jeon
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/* A big thanks to Alden Hart of Synthetos, supplier of grblshield and TinyG, who has
|
|
been integral throughout the development of the higher level details of Grbl, as well
|
|
as being a consistent sounding board for the future of accessible and free CNC. */
|
|
|
|
#include <avr/interrupt.h>
|
|
#include <avr/pgmspace.h>
|
|
#include "config.h"
|
|
#include "planner.h"
|
|
#include "nuts_bolts.h"
|
|
#include "stepper.h"
|
|
#include "spindle_control.h"
|
|
#include "coolant_control.h"
|
|
#include "motion_control.h"
|
|
#include "gcode.h"
|
|
#include "protocol.h"
|
|
#include "limits.h"
|
|
#include "report.h"
|
|
#include "settings.h"
|
|
#include "serial.h"
|
|
|
|
// Declare system global variable structure
|
|
system_t sys;
|
|
|
|
int main(void)
|
|
{
|
|
// Initialize system
|
|
serial_init(); // Setup serial baud rate and interrupts
|
|
settings_init(); // Load grbl settings from EEPROM
|
|
st_init(); // Setup stepper pins and interrupt timers
|
|
sei(); // Enable interrupts
|
|
|
|
memset(&sys, 0, sizeof(sys)); // Clear all system variables
|
|
sys.abort = true; // Set abort to complete initialization
|
|
sys.state = STATE_INIT; // Set alarm state to indicate unknown initial position
|
|
|
|
for(;;) {
|
|
|
|
// Execute system reset upon a system abort, where the main program will return to this loop.
|
|
// Once here, it is safe to re-initialize the system. At startup, the system will automatically
|
|
// reset to finish the initialization process.
|
|
if (sys.abort) {
|
|
// Reset system.
|
|
serial_reset_read_buffer(); // Clear serial read buffer
|
|
plan_init(); // Clear block buffer and planner variables
|
|
gc_init(); // Set g-code parser to default state
|
|
protocol_init(); // Clear incoming line data and execute startup lines
|
|
spindle_init();
|
|
coolant_init();
|
|
limits_init();
|
|
st_reset(); // Clear stepper subsystem variables.
|
|
|
|
// Sync cleared gcode and planner positions to current system position, which is only
|
|
// cleared upon startup, not a reset/abort.
|
|
plan_sync_position();
|
|
gc_sync_position();
|
|
|
|
// Reset system variables.
|
|
sys.abort = false;
|
|
sys.execute = 0;
|
|
if (bit_istrue(settings.flags,BITFLAG_AUTO_START)) { sys.auto_start = true; }
|
|
|
|
// Check for power-up and set system alarm if homing is enabled to force homing cycle
|
|
// by setting Grbl's alarm state. Alarm locks out all g-code commands, including the
|
|
// startup scripts, but allows access to settings and internal commands. Only a homing
|
|
// cycle '$H' or kill alarm locks '$X' will disable the alarm.
|
|
// NOTE: The startup script will run after successful completion of the homing cycle, but
|
|
// not after disabling the alarm locks. Prevents motion startup blocks from crashing into
|
|
// things uncontrollably. Very bad.
|
|
#ifdef HOMING_INIT_LOCK
|
|
if (sys.state == STATE_INIT && bit_istrue(settings.flags,BITFLAG_HOMING_ENABLE)) { sys.state = STATE_ALARM; }
|
|
#endif
|
|
|
|
// Check for and report alarm state after a reset, error, or an initial power up.
|
|
if (sys.state == STATE_ALARM) {
|
|
report_feedback_message(MESSAGE_ALARM_LOCK);
|
|
} else {
|
|
// All systems go. Set system to ready and execute startup script.
|
|
sys.state = STATE_IDLE;
|
|
protocol_execute_startup();
|
|
}
|
|
}
|
|
|
|
protocol_execute_runtime();
|
|
|
|
// When the serial protocol returns, there are no more characters in the serial read buffer to
|
|
// be processed and executed. This indicates that individual commands are being issued or
|
|
// streaming is finished. In either case, auto-cycle start, if enabled, any queued moves.
|
|
mc_auto_cycle_start();
|
|
protocol_process(); // ... process the serial protocol
|
|
|
|
}
|
|
return 0; /* never reached */
|
|
}
|