ManuelW/grbl-LPC-CoreXY
1
0
Fork 0
Code Issues Pull Requests Releases 1 Wiki Activity
0721e573ef
grbl-LPC-CoreXY/grbl/spindle_control.c

224 lines
7.9 KiB
C
Raw Blame History

/*
spindle_control.c - spindle control methods
Part of Grbl
Copyright (c) 2012-2016 Sungeun K. Jeon for Gnea Research LLC
Copyright (c) 2009-2011 Simen Svale Skogsrud
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
#include "grbl.h"
#include "pwm_driver.h"
#ifdef VARIABLE_SPINDLE
static float pwm_gradient; // Precalulated value to speed up rpm to PWM conversions.
float spindle_pwm_period;
float spindle_pwm_off_value;
float spindle_pwm_min_value;
float spindle_pwm_max_value;
#endif
void spindle_init()
{
#ifdef VARIABLE_SPINDLE
spindle_pwm_period = (SystemCoreClock / settings.spindle_pwm_freq);
spindle_pwm_off_value = (spindle_pwm_period * settings.spindle_pwm_off_value / 100);
spindle_pwm_min_value = (spindle_pwm_period * settings.spindle_pwm_min_value / 100);
spindle_pwm_max_value = (spindle_pwm_period * settings.spindle_pwm_max_value / 100);
pwm_init(&SPINDLE_PWM_CHANNEL, SPINDLE_PWM_USE_PRIMARY_PIN, SPINDLE_PWM_USE_SECONDARY_PIN, spindle_pwm_period, 0);
pwm_enable(&SPINDLE_PWM_CHANNEL);
// Configure variable spindle PWM and enable pin, if requried. On the Uno, PWM and enable are
// combined unless configured otherwise.
#ifdef USE_SPINDLE_DIR_AS_ENABLE_PIN
SPINDLE_ENABLE_DDR |= (1<<SPINDLE_ENABLE_BIT); // Configure as output pin.
#else
SPINDLE_DIRECTION_DDR |= (1<<SPINDLE_DIRECTION_BIT); // Configure as output pin.
#endif
pwm_gradient = (spindle_pwm_max_value-spindle_pwm_min_value)/(settings.rpm_max-settings.rpm_min);
#else
// Configure no variable spindle and only enable pin.
SPINDLE_ENABLE_DDR |= (1<<SPINDLE_ENABLE_BIT); // Configure as output pin.
SPINDLE_DIRECTION_DDR |= (1<<SPINDLE_DIRECTION_BIT); // Configure as output pin.
#endif
spindle_stop();
}
uint8_t spindle_get_state()
{
#ifdef VARIABLE_SPINDLE
#ifdef USE_SPINDLE_DIR_AS_ENABLE_PIN
// No spindle direction output pin.
#ifdef INVERT_SPINDLE_ENABLE_PIN
if (bit_isfalse(SPINDLE_ENABLE_PORT,(1<<SPINDLE_ENABLE_BIT))) { return(SPINDLE_STATE_CW); }
#else
if (bit_istrue(SPINDLE_ENABLE_PORT,(1<<SPINDLE_ENABLE_BIT))) { return(SPINDLE_STATE_CW); }
#endif
#else
if (SPINDLE_TCCRA_REGISTER & (1<<SPINDLE_COMB_BIT)) { // Check if PWM is enabled.
if (SPINDLE_DIRECTION_PORT & (1<<SPINDLE_DIRECTION_BIT)) { return(SPINDLE_STATE_CCW); }
else { return(SPINDLE_STATE_CW); }
}
#endif
#else
#ifdef INVERT_SPINDLE_ENABLE_PIN
if (bit_isfalse(SPINDLE_ENABLE_PORT,(1<<SPINDLE_ENABLE_BIT))) {
#else
if (bit_istrue(SPINDLE_ENABLE_PORT,(1<<SPINDLE_ENABLE_BIT))) {
#endif
if (SPINDLE_DIRECTION_PORT & (1<<SPINDLE_DIRECTION_BIT)) { return(SPINDLE_STATE_CCW); }
else { return(SPINDLE_STATE_CW); }
}
#endif
return(SPINDLE_STATE_DISABLE);
}
// Disables the spindle and sets PWM output to zero when PWM variable spindle speed is enabled.
// Called by various main program and ISR routines. Keep routine small, fast, and efficient.
// Called by spindle_init(), spindle_set_speed(), spindle_set_state(), and mc_reset().
void spindle_stop()
{
#ifdef VARIABLE_SPINDLE
pwm_set_width(&SPINDLE_PWM_CHANNEL, 0);
#ifdef USE_SPINDLE_DIR_AS_ENABLE_PIN
#ifdef INVERT_SPINDLE_ENABLE_PIN
SPINDLE_ENABLE_PORT |= (1<<SPINDLE_ENABLE_BIT); // Set pin to high
#else
SPINDLE_ENABLE_PORT &= ~(1<<SPINDLE_ENABLE_BIT); // Set pin to low
#endif
#endif
#else
#ifdef INVERT_SPINDLE_ENABLE_PIN
SPINDLE_ENABLE_PORT |= (1<<SPINDLE_ENABLE_BIT); // Set pin to high
#else
SPINDLE_ENABLE_PORT &= ~(1<<SPINDLE_ENABLE_BIT); // Set pin to low
#endif
#endif
}
#ifdef VARIABLE_SPINDLE
// Sets spindle speed PWM output and enable pin, if configured. Called by spindle_set_state()
// and stepper ISR. Keep routine small and efficient.
void spindle_set_speed(uint32_t pwm_value)
{
pwm_set_width(&SPINDLE_PWM_CHANNEL, pwm_value);
}
// Called by spindle_set_state() and step segment generator. Keep routine small and efficient.
uint32_t spindle_compute_pwm_value(float rpm)
{
uint32_t pwm_value;
rpm *= (0.010*sys.spindle_speed_ovr); // Scale by spindle speed override value.
if (rpm <= 0) {
sys.spindle_speed = 0;
pwm_value = spindle_pwm_off_value;
}
else if (rpm <= settings.rpm_min) {
sys.spindle_speed = settings.rpm_min;
pwm_value = spindle_pwm_min_value;
}
else if (rpm >= settings.rpm_max) {
sys.spindle_speed = settings.rpm_max;
pwm_value = spindle_pwm_max_value - 1;
}
else {
sys.spindle_speed = rpm;
pwm_value = floor((rpm - settings.rpm_min) * pwm_gradient) + spindle_pwm_min_value;
if(pwm_value >= spindle_pwm_max_value)
pwm_value = spindle_pwm_max_value - 1;
}
return(pwm_value);
}
#endif
// Immediately sets spindle running state with direction and spindle rpm via PWM, if enabled.
// Called by g-code parser spindle_sync(), parking retract and restore, g-code program end,
// sleep, and spindle stop override.
#ifdef VARIABLE_SPINDLE
void spindle_set_state(uint8_t state, float rpm)
#else
void _spindle_set_state(uint8_t state)
#endif
{
if (sys.abort) { return; } // Block during abort.
if (state == SPINDLE_DISABLE) { // Halt or set spindle direction and rpm.
#ifdef VARIABLE_SPINDLE
sys.spindle_speed = 0.0;
#endif
spindle_stop();
} else {
#ifndef USE_SPINDLE_DIR_AS_ENABLE_PIN
if (state == SPINDLE_ENABLE_CW) {
SPINDLE_DIRECTION_PORT &= ~(1<<SPINDLE_DIRECTION_BIT);
} else {
SPINDLE_DIRECTION_PORT |= (1<<SPINDLE_DIRECTION_BIT);
}
#endif
#ifdef VARIABLE_SPINDLE
// NOTE: Assumes all calls to this function is when Grbl is not moving or must remain off.
if (settings.flags & BITFLAG_LASER_MODE) {
if (state == SPINDLE_ENABLE_CCW) { rpm = 0.0; } // TODO: May need to be rpm_min*(100/MAX_SPINDLE_SPEED_OVERRIDE);
}
spindle_set_speed(spindle_compute_pwm_value(rpm));
#endif
#if (defined(USE_SPINDLE_DIR_AS_ENABLE_PIN) && \
!defined(SPINDLE_ENABLE_OFF_WITH_ZERO_SPEED)) || !defined(VARIABLE_SPINDLE)
// NOTE: Without variable spindle, the enable bit should just turn on or off, regardless
// if the spindle speed value is zero, as its ignored anyhow.
#ifdef INVERT_SPINDLE_ENABLE_PIN
SPINDLE_ENABLE_PORT &= ~(1<<SPINDLE_ENABLE_BIT);
#else
SPINDLE_ENABLE_PORT |= (1<<SPINDLE_ENABLE_BIT);
#endif
#endif
}
sys.report_ovr_counter = 0; // Set to report change immediately
}
// G-code parser entry-point for setting spindle state. Forces a planner buffer sync and bails
// if an abort or check-mode is active.
#ifdef VARIABLE_SPINDLE
void spindle_sync(uint8_t state, float rpm)
{
if (sys.state == STATE_CHECK_MODE) { return; }
protocol_buffer_synchronize(); // Empty planner buffer to ensure spindle is set when programmed.
spindle_set_state(state,rpm);
}
#else
void _spindle_sync(uint8_t state)
{
if (sys.state == STATE_CHECK_MODE) { return; }
protocol_buffer_synchronize(); // Empty planner buffer to ensure spindle is set when programmed.
_spindle_set_state(state);
}
#endif
Reference in New Issue View Git Blame Copy Permalink