/*
  stepper_plan.h - buffers movement commands and manages the acceleration profile plan
  Part of Grbl

  Copyright (c) 2009-2011 Simen Svale Skogsrud

  Grbl is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  Grbl is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with Grbl.  If not, see <http://www.gnu.org/licenses/>.
*/

// This module is to be considered a sub-module of stepper.c. Please don't include 
// this file from any other module.

#ifndef stepper_plan_h
#define stepper_plan_h
                 
#include <inttypes.h>

// Pick a suitable block-buffer size
#define BLOCK_BUFFER_SIZE 20   // Atmega 328 has one full kilobyte of extra RAM!

// This struct is used when buffering the setup for each linear movement "nominal" values are as specified in 
// the source g-code and may never actually be reached if acceleration management is active.
typedef struct {
  // Fields used by the bresenham algorithm for tracing the line
  uint32_t steps_x, steps_y, steps_z; // Step count along each axis
  uint8_t  direction_bits;            // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
  int32_t  step_event_count;          // The number of step events required to complete this block
  uint32_t nominal_rate;              // The nominal step rate for this block in step_events/minute
  
  // Fields used by the motion planner to manage acceleration
  double speed_x, speed_y, speed_z;   // Nominal mm/minute for each axis
  double nominal_speed;               // The nominal speed for this block in mm/min  
  double millimeters;                 // The total travel of this block in mm
  double entry_factor;                // The factor representing the change in speed at the start of this trapezoid.
                                      // (The end of the curren speed trapezoid is defined by the entry_factor of the
                                      // next block)
  
  // Settings for the trapezoid generator
  uint32_t initial_rate;              // The jerk-adjusted step rate at start of block  
  int32_t rate_delta;                 // The steps/minute to add or subtract when changing speed (must be positive)
  uint32_t accelerate_until;          // The index of the step event on which to stop acceleration
  uint32_t decelerate_after;          // The index of the step event on which to start decelerating
  
  // Debug fields, PLEASE REMOVE
  uint32_t exit_rate;
} block_t;
      
extern block_t block_buffer[BLOCK_BUFFER_SIZE]; // A ring buffer for motion instructions
extern volatile int block_buffer_head;           // Index of the next block to be pushed
extern volatile int block_buffer_tail;           // Index of the block to process now
extern int32_t position[3];

// Initialize the motion plan subsystem      
void plan_init();

// Do not call directly unless you are writing a motor driver. In current iteration this is called by 
// st_buffer_line which also wakes up the stepper subsystem.
// Add a new linear movement to the buffer. steps_x, _y and _z is the signed, relative motion in 
// steps. Microseconds specify how many microseconds the move should take to perform. To aid acceleration
// calculation the caller must also provide the physical length of the line in millimeters.
void plan_buffer_line(double x, double y, double z, double feed_rate, int invert_feed_rate);

// Enables acceleration-management for upcoming blocks
void plan_set_acceleration_manager_enabled(int enabled);
// Is acceleration-management currently enabled?
int plan_is_acceleration_manager_enabled();

#endif