/*
  system.c - Handles system level commands and real-time processes
  Part of Grbl

  Copyright (c) 2014 Sungeun K. Jeon  

  Grbl is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  Grbl is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with Grbl.  If not, see <http://www.gnu.org/licenses/>.
*/

#include "system.h"
#include "settings.h"
#include "gcode.h"
#include "motion_control.h"
#include "report.h"
#include "print.h"


void system_init() 
{
  PINOUT_DDR &= ~(PINOUT_MASK); // Configure as input pins
  PINOUT_PORT |= PINOUT_MASK;   // Enable internal pull-up resistors. Normal high operation.
  PINOUT_PCMSK |= PINOUT_MASK;  // Enable specific pins of the Pin Change Interrupt
  PCICR |= (1 << PINOUT_INT);   // Enable Pin Change Interrupt
}


// Pin change interrupt for pin-out commands, i.e. cycle start, feed hold, and reset. Sets
// only the runtime command execute variable to have the main program execute these when 
// its ready. This works exactly like the character-based runtime commands when picked off
// directly from the incoming serial data stream.
ISR(PINOUT_INT_vect) 
{
  // Enter only if any pinout pin is actively low.
  if ((PINOUT_PIN & PINOUT_MASK) ^ PINOUT_MASK) { 
    if (bit_isfalse(PINOUT_PIN,bit(PIN_RESET))) {
      mc_reset();
    } else if (bit_isfalse(PINOUT_PIN,bit(PIN_FEED_HOLD))) {
      sys.execute |= EXEC_FEED_HOLD; 
    } else if (bit_isfalse(PINOUT_PIN,bit(PIN_CYCLE_START))) {
      sys.execute |= EXEC_CYCLE_START;
    } 
  }
}


// Executes user startup script, if stored.
void system_execute_startup(char *line) 
{
  uint8_t n;
  for (n=0; n < N_STARTUP_LINE; n++) {
    if (!(settings_read_startup_line(n, line))) {
      report_status_message(STATUS_SETTING_READ_FAIL);
    } else {
      if (line[0] != 0) {
        printString(line); // Echo startup line to indicate execution.
        report_status_message(gc_execute_line(line));
      }
    } 
  }  
}


// Directs and executes one line of formatted input from protocol_process. While mostly
// incoming streaming g-code blocks, this also executes Grbl internal commands, such as 
// settings, initiating the homing cycle, and toggling switch states. This differs from
// the runtime command module by being susceptible to when Grbl is ready to execute the 
// next line during a cycle, so for switches like block delete, the switch only effects
// the lines that are processed afterward, not necessarily real-time during a cycle, 
// since there are motions already stored in the buffer. However, this 'lag' should not
// be an issue, since these commands are not typically used during a cycle.
uint8_t system_execute_line(char *line) 
{   
  uint8_t char_counter = 1; 
  uint8_t helper_var = 0; // Helper variable
  float parameter, value;
  switch( line[char_counter] ) {
    case 0 : report_grbl_help(); break;
    case 'G' : // Prints gcode parser state
      if ( line[++char_counter] != 0 ) { return(STATUS_UNSUPPORTED_STATEMENT); }
      else { report_gcode_modes(); }
      break;   
    case 'C' : // Set check g-code mode [IDLE/CHECK]
      if ( line[++char_counter] != 0 ) { return(STATUS_UNSUPPORTED_STATEMENT); }
      // Perform reset when toggling off. Check g-code mode should only work if Grbl
      // is idle and ready, regardless of alarm locks. This is mainly to keep things
      // simple and consistent.
      if ( sys.state == STATE_CHECK_MODE ) { 
        mc_reset(); 
        report_feedback_message(MESSAGE_DISABLED);
      } else {
        if (sys.state) { return(STATUS_IDLE_ERROR); } // Requires no alarm mode.
        sys.state = STATE_CHECK_MODE;
        report_feedback_message(MESSAGE_ENABLED);
      }
      break; 
    case 'X' : // Disable alarm lock [ALARM]
      if ( line[++char_counter] != 0 ) { return(STATUS_UNSUPPORTED_STATEMENT); }
      if (sys.state == STATE_ALARM) { 
        report_feedback_message(MESSAGE_ALARM_UNLOCK);
        sys.state = STATE_IDLE;
        // Don't run startup script. Prevents stored moves in startup from causing accidents.
      } // Otherwise, no effect.
      break;               
//  case 'J' : break;  // Jogging methods
    // TODO: Here jogging can be placed for execution as a seperate subprogram. It does not need to be 
    // susceptible to other runtime commands except for e-stop. The jogging function is intended to
    // be a basic toggle on/off with controlled acceleration and deceleration to prevent skipped 
    // steps. The user would supply the desired feedrate, axis to move, and direction. Toggle on would
    // start motion and toggle off would initiate a deceleration to stop. One could 'feather' the
    // motion by repeatedly toggling to slow the motion to the desired location. Location data would 
    // need to be updated real-time and supplied to the user through status queries.
    //   More controlled exact motions can be taken care of by inputting G0 or G1 commands, which are 
    // handled by the planner. It would be possible for the jog subprogram to insert blocks into the
    // block buffer without having the planner plan them. It would need to manage de/ac-celerations 
    // on its own carefully. This approach could be effective and possibly size/memory efficient.        
    default : 
      // Block any system command that requires the state as IDLE/ALARM. (i.e. EEPROM, homing)
      if ( !(sys.state == STATE_IDLE || sys.state == STATE_ALARM) ) { return(STATUS_IDLE_ERROR); }
      switch( line[char_counter] ) {
        case '$' : // Prints Grbl settings [IDLE/ALARM]
          if ( line[++char_counter] != 0 ) { return(STATUS_UNSUPPORTED_STATEMENT); }
          else { report_grbl_settings(); }
          break;
        case '#' : // Print Grbl NGC parameters
          if ( line[++char_counter] != 0 ) { return(STATUS_UNSUPPORTED_STATEMENT); }
          else { report_ngc_parameters(); }
          break;          
        case 'H' : // Perform homing cycle [IDLE/ALARM]
          if (bit_istrue(settings.flags,BITFLAG_HOMING_ENABLE)) { 
            // Only perform homing if Grbl is idle or lost.
            mc_homing_cycle(); 
            if (!sys.abort) { system_execute_startup(line); } // Execute startup scripts after successful homing.
          } else { return(STATUS_SETTING_DISABLED); }
          break;
        case 'I' : // Print or store build info. [IDLE/ALARM]
          if ( line[++char_counter] == 0 ) { 
            if (!(settings_read_build_info(line))) {
              report_status_message(STATUS_SETTING_READ_FAIL);
            } else {
              report_build_info(line);
            }
          } else { // Store startup line [IDLE/ALARM]
            if(line[char_counter++] != '=') { return(STATUS_UNSUPPORTED_STATEMENT); }
            helper_var = char_counter; // Set helper variable as counter to start of user info line.
            do {
              line[char_counter-helper_var] = line[char_counter];
            } while (line[char_counter++] != 0);
            settings_store_build_info(line);
          }
          break;                 
        case 'N' : // Startup lines. [IDLE/ALARM]
          if ( line[++char_counter] == 0 ) { // Print startup lines
            for (helper_var=0; helper_var < N_STARTUP_LINE; helper_var++) {
              if (!(settings_read_startup_line(helper_var, line))) {
                report_status_message(STATUS_SETTING_READ_FAIL);
              } else {
                report_startup_line(helper_var,line);
              }
            }
            break;
          } else { // Store startup line [IDLE Only] Prevents motion during ALARM.
            if (sys.state != STATE_IDLE) { return(STATUS_IDLE_ERROR); } // Store only when idle.
            helper_var = true;  // Set helper_var to flag storing method. 
            // No break. Continues into default: to read remaining command characters.
          }
        default :  // Storing setting methods [IDLE/ALARM]
          if(!read_float(line, &char_counter, &parameter)) { return(STATUS_BAD_NUMBER_FORMAT); }
          if(line[char_counter++] != '=') { return(STATUS_UNSUPPORTED_STATEMENT); }
          if (helper_var) { // Store startup line
            // Prepare sending gcode block to gcode parser by shifting all characters
            helper_var = char_counter; // Set helper variable as counter to start of gcode block
            do {
              line[char_counter-helper_var] = line[char_counter];
            } while (line[char_counter++] != 0);
            // Execute gcode block to ensure block is valid.
            helper_var = gc_execute_line(line); // Set helper_var to returned status code.
            if (helper_var) { return(helper_var); }
            else { 
              helper_var = trunc(parameter); // Set helper_var to int value of parameter
              settings_store_startup_line(helper_var,line);
            }
          } else { // Store global setting.
            if(!read_float(line, &char_counter, &value)) { return(STATUS_BAD_NUMBER_FORMAT); }
            if(line[char_counter] != 0) { return(STATUS_UNSUPPORTED_STATEMENT); }
            return(settings_store_global_setting(parameter, value));
          }
      }    
  }
  return(STATUS_OK); // If '$' command makes it to here, then everything's ok.
}