/*
  spindle_control.c - spindle control methods
  Part of Grbl

  Copyright (c) 2012-2015 Sungeun K. Jeon
  Copyright (c) 2009-2011 Simen Svale Skogsrud

  Grbl is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  Grbl is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with Grbl.  If not, see <http://www.gnu.org/licenses/>.
*/

#include "grbl.h"


void spindle_init()
{    
  // On the Uno, spindle enable and PWM are shared. Other CPUs have seperate enable pin.
  #ifdef VARIABLE_SPINDLE
    SPINDLE_PWM_DDR |= (1<<SPINDLE_PWM_BIT); // Configure as PWM output pin.
    #ifndef CPU_MAP_ATMEGA328P 
      SPINDLE_ENABLE_DDR |= (1<<SPINDLE_ENABLE_BIT); // Configure as output pin.
    #endif     
  #else
    SPINDLE_ENABLE_DDR |= (1<<SPINDLE_ENABLE_BIT); // Configure as output pin.
  #endif
  SPINDLE_DIRECTION_DDR |= (1<<SPINDLE_DIRECTION_BIT); // Configure as output pin.
  spindle_stop();
}


void spindle_stop()
{
  // On the Uno, spindle enable and PWM are shared. Other CPUs have seperate enable pin.
  #ifdef VARIABLE_SPINDLE
    TCCRA_REGISTER &= ~(1<<COMB_BIT); // Disable PWM. Output voltage is zero.
    #ifndef CPU_MAP_ATMEGA328P 
      SPINDLE_ENABLE_PORT &= ~(1<<SPINDLE_ENABLE_BIT); // Set pin to low.
    #endif
  #else
    SPINDLE_ENABLE_PORT &= ~(1<<SPINDLE_ENABLE_BIT); // Set pin to low.
  #endif  
}


void spindle_set_state(uint8_t state, float rpm)
{
  // Halt or set spindle direction and rpm. 
  if (state == SPINDLE_DISABLE) {

    spindle_stop();

  } else {

    if (state == SPINDLE_ENABLE_CW) {
      SPINDLE_DIRECTION_PORT &= ~(1<<SPINDLE_DIRECTION_BIT);
    } else {
      SPINDLE_DIRECTION_PORT |= (1<<SPINDLE_DIRECTION_BIT);
    }

    #ifdef VARIABLE_SPINDLE
      // TODO: Install the optional capability for frequency-based output for servos.
      #ifdef CPU_MAP_ATMEGA2560
      	TCCRA_REGISTER = (1<<COMB_BIT) | (1<<WAVE1_REGISTER) | (1<<WAVE0_REGISTER);
        TCCRB_REGISTER = (TCCRB_REGISTER & 0b11111000) | 0x02 | (1<<WAVE2_REGISTER) | (1<<WAVE3_REGISTER); // set to 1/8 Prescaler
        OCR4A = 0xFFFF; // set the top 16bit value
        uint16_t current_pwm;
      #else
        TCCRA_REGISTER = (1<<COMB_BIT) | (1<<WAVE1_REGISTER) | (1<<WAVE0_REGISTER);
        TCCRB_REGISTER = (TCCRB_REGISTER & 0b11111000) | 0x02; // set to 1/8 Prescaler
        uint8_t current_pwm;
      #endif

      #define SPINDLE_RPM_RANGE (SPINDLE_MAX_RPM-SPINDLE_MIN_RPM)
      if ( rpm < SPINDLE_MIN_RPM ) { rpm = 0; } 
      else { 
        rpm -= SPINDLE_MIN_RPM; 
        if ( rpm > SPINDLE_RPM_RANGE ) { rpm = SPINDLE_RPM_RANGE; } // Prevent integer overflow
      }
      current_pwm = floor( rpm*(PWM_MAX_VALUE/SPINDLE_RPM_RANGE) + 0.5);
      #ifdef MINIMUM_SPINDLE_PWM
        if (current_pwm < MINIMUM_SPINDLE_PWM) { current_pwm = MINIMUM_SPINDLE_PWM; }
      #endif
      OCR_REGISTER = current_pwm; // Set PWM pin output
    
      #ifdef CPU_MAP_ATMEGA2560 // On the Uno, spindle enable and PWM are shared.
        SPINDLE_ENABLE_PORT |= (1<<SPINDLE_ENABLE_BIT);
      #endif
    #else   
      SPINDLE_ENABLE_PORT |= (1<<SPINDLE_ENABLE_BIT);
    #endif

  }
}


void spindle_run(uint8_t state, float rpm)
{
  if (sys.state == STATE_CHECK_MODE) { return; }
  protocol_buffer_synchronize(); // Empty planner buffer to ensure spindle is set when programmed.  
  spindle_set_state(state, rpm);
}