- New $SLP sleep mode that will disable spindle, coolant, and stepper
enable pins. Allows users to disable their steppers without having to
alter their settings. A reset is required to exit and re-initializes in
alarm state.
- Laser mode wasn’t updating the spindle PWM correctly (effected
spindle speed overrides) and not checking for modal states either.
Fixed both issues.
- While in laser mode, parking motions are ignored, since the power off
delay with the retract motion would burn the material. It will just
turn off and not move. A restore immediately powers up and resumes. No
delays.
- Changing rpm max and min settings did not update the spindle PWM
calculations. Now fixed.
- Increased default planner buffer from 16 to 17 block. It seems to be
stable, but need to monitor this carefully.
- Removed software debounce routine for limit pins. Obsolete.
- Fixed a couple parking motion bugs. One related to restoring
incorrectly and the other the parking rate wasn’t compatible with the
planner structs.
- Fixed a bug caused by refactoring the critical alarms in a recent
push. Soft limits weren’t invoking a critical alarm.
- Updated the documentation with the new sleep feature and added some
more details to the change summary.
- Added a new jog cancel real-time command. Rather than depending on a
feed hold to cancel a jogging motion, this realtime command can be used
instead. The main advantage is if a feed hold is used, you can
accidentally hold the machine right when Grbl returns to IDLE after
completing a jog. And the GUI doesn’t have to worry about tracking this
either.
- Fixed a typo in the g-code parser edits from the last push. Was
causing the G10 set coordinate system command to not work correctly.
- Updated the documentation with the jog cancel command.
- Freed up another 60 bytes of flash and 12-24 bytes of stack RAM by
using the pre-allocated IJK arc offset vector that is guaranteed to be
not in use. Only G10 and G28/30 require fetching from EEPROM and
retaining extra data. Both commands use axis words, which rules out
G2/3 arcs using IJK offsets existing in same block. Not ideal, but
every byte helps.
- Edited README.
- Increment to v1.1b due to status report tweak.
- Tweaked the buffer state status reports to show bytes and blocks
available, rather than in use. This does not require knowing the buffer
sizes beforehand. It’s implicit.
- Also, since buffer states are not used by most devs (after
inquiries), it is no longer enabled by default and a status mask option
was added for this.
- Fixed some typos and updated for the report tweak in the
documentation.
- Wrote a joystick implementation concept in the jogging markdown
document. Outlines how to get a low-latency feel to a joystick (and
other input devices).
- Removed XON/XOFF support. It’s not used by anyone because of its
inherent problems. Remains in older versions for reference.
- Added a compile option on how to handle the probe position during a
check mode.
- Fixed a jogging bug. If G93 is the modal state before a jogging
motion, the feed rate did not get calculated correctly. Fixed the issue.
- Refactored some code to save another 160+ bytes. Included an improved
float vector comparison macro and reducing a few large and repetitive
function calls.
- Fixed a probing bug (existing in v0.9 too) where the target positions
were not set correct and error handling was improper.
- The newest Arduino IDE 1.6.12 has recently updated to avr-gcc v4.9.2.
Unfortunately, it produces a compiled size almost 0.7KB to 1KB larger
than prior versions! This can easily cause the base build to exceed the
Arduino Duemilanove/Nano flash limit of 30.5KB. The Arduino Uno seems
to be ok still with its 31.5KB flash limit.
- Makefile `-flto` compile flag added to cut down on the horrible flash
size when using the new avr-gcc. (Edit Makefile and remove comment on
COMPILE definition). This brings it in-line with what the IDE produces.
- Functionalized repetitive tasks in report.c to try to reduce overall
flash size. Successfully cut down about 160bytes.
- Removed printFloat_SettingValue() and printFloat_RPMValue()
functions. These aren’t required and can be replaced with a direct call
to printFloat() because they don’t require a unit conversion check.
- Reverted back the serial RX count function to how it was. The
variable type was unsigned and cause an integer underflow whenever the
calculation produced a negative number. The old way was the correct way.
- Lots of minor edits to the code CSVs and markdown documents.
- Expanded on explaining feedback messages and startup line execution
feedback.
- Created a new settings codes CSV to help GUIs import the values and
meanings.
- Incremented to v1.1a, rather than keep 1.0e. This is because there
are existing v1.0 installations. Don’t want to confuse people further.
- Certain version of the Arduino IDE did not like the `inline` in the
function header. Removed from spindle_control files to fix the problem.
- Tweaked the communication protocol slightly. Added message type
indicators for all `[]`bracketed feedback messages. It’s been
problematic for GUI dev to try to determine the context of a message
and how it should be handled. These indictors should help tremendously
to remove context all together.
- Also altered how `$N` startup lines are presented when executed. They
now start with an open chevron ‘>’ followed by the line and an ‘:ok’ to
indicate it executed. The ‘ok’ is on the same line intentionally so it
doesn’t mess up a streaming protocol counter.
- Managed to save a 100+KB from refactoring parts of report.c. (Thanks
Vasilis!) Freed up room to alter the protocol a little.
- Wrote a markdown document on interface messaging to make it clear how
it’s intended to work. See interface.md in /doc/markdown
- Started to pull in some Wiki pages from the old grbl site and
beginning to update them for v1.1.
- Created new commit log for v1.1.
- Mega2560 support has been moved to the Grbl-Mega
[project](http://github.com/gnea/grbl-Mega/) to clean up the code and
make future developments easier with increased flash and RAM. All new
developments between the 328p and Mega2560 will be synced when it makes
sense to.
- OEM single file compile configuration option. Before OEMs needed to
alter three files. Provided a way to just alter the config.h file to
contain everything for a particular Grbl build. See config.h for more
details.
- Removed defaults and cpu_map directories and reverted back to
defaults.h and cpu_map.h to contain all definitions. This should help
reduce some headaches and the previous implementation inadvertently
created. Also, it makes the single file config.h possible.
- Moved (and tweaked) the invert control pin mask define and placed
into config.h, rather than in the cpu_map.h file. Makes more sense
there.
- Soft limit errors were stuck in a feed hold without notifying the
user why it was in a hold. When resumed, the soft limit error would
kick in. Issue should be fixed to behave as intended to automatically
hold and issue a soft limit alarm once the machine has come to a stop.
- Soft limit errors were stuck in a feed hold without notifying the
user why it was in a hold. When resumed, the soft limit error would
kick in. Issue should be fixed to behave as intended. To automatically
hold and issue a soft limit alarm once the machine has come to a stop.
- Planner was under-estimating maximum speeds through straight
junctions in certain cases. The calculations have been updated to be
more accurate.
- Strange sizeof() bug in the most recent releases. Manifested as an
alarm upon a power up even when homing was disabled. Fixed by declaring
sizeof() with struct types, rather than variable names, even though
they were validated to give the same value.
- Spindle speed zero should disable the spindle. Now fixed.
- New configuration option for inverting certain limit pins. Handy for
mixed NO and NC switch machines. See config.h for details.
- New pin state realtime reporting feature. Instead of `Lim:000` for
limit state reports, the new feature shows `Pin:000|0|0000`, or
something similar. The `|` delimited fields indicate xyz limits, probe,
and control pin states, where 0 is always not triggered, and 1 is
triggered. Invert masks ARE accounted for.
Each field may be enabled or disabled via the `$10` status report
setting. The probe and control pin flags are bits 5 and 6, respectively.
- Remove the now deprecated `REPORT_CONTROL_PIN_STATE` option in
config.h
- The old limit pin reports `Lim:000` may be re-enabled by commenting
out `REPORT_ALL_PIN_STATES` in config.h.
- Incremented the version letter (v1.0c) to indicate the change in
reporting style.
- Replaced all bit_true_atomic and bit_false_atomic macros with
function calls. This saved a couple hundred bytes of flash.
- G38.x was not printing correctly in the $G g-code state reports. Now
fixed.
- When investigating the above issue, it was noticed that G38.x
wouldn’t show at all, but instead a G0 would be printed. This was
unlike the v0.9j master build. It turned out volatile variables do not
like to be defined inside a C struct. These are undefined on how to be
handled. Once pulled out, all weird issues went away.
- Also changed two ‘sizeof()’ statements in the mc_probe() and
probe_state_monitor() functions to be more robust later on.
- Updated the commit logs to individual files for each minor release.
Forgot to update the generating script to account for this.
- G38.x was not printing correctly in the $G g-code state reports. Now
fixed.
- Potential bug regarding volatile variables inside a struct. It has
never been a problem in v0.9, but ran into this during v1.0
development. Just to be safe, the fixes are applied here.
- Updated pre-built firmwares with these two bug fixes.
- G28 and G30’s behavior has been updated from the old NIST g-code
standard to LinuxCNC’s. Previously when an intermediate motion was
programmed, the NIST standard would move all axes to the final G28/30
stored coordinates. LinuxCNC states it only moves the axes specified in
the command.
For example, suppose G28’s stored position is (x,y,z) = (1,2,3) for
simplicity, and we want to do an automated z-axis tool retraction and
then park at the x,y location. `G28 G91 Z5` will first move the Z axis
5mm(or inches) up, then move Z to position 3 in machine coordinates.
Next, the command `G28 G91 X0 Y0` would skip the intermediate move
since distance is zero, but then move only the x and y axes to machine
coordinates 1 and 2, respectively. The z-axis wouldn’t move in this
case, since it wasn’t specified.
This change is intended to make Grbl more LinuxCNC compatible while
making commands, like the shown tool retraction, much easier to
implement.
- Version bump requested by OEMs to easily determine whether the
firmware supports the new EEPROM reset feature. Other than that, no
significant changes.
- Tweaked the previous EEPROM restore implementation and added new
functionality.
- `$RST=$` restores the `$$` grbl settings back to firmware defaults,
which are set when compiled.
- `$RST=#` restores the `$#` parameters in EEPROM. At times it’s useful
to clear these and start over, rather than manually writing each entry.
-`$RST=*` wipe all of the data in EEPROM that Grbl uses and restores
them to defaults. This includes `$$` settings, `$#` parameters, `$N`
startup lines, and `$i` build info string.
NOTE: This doesn’t write zeros throughout the EEPROM. It only writes
where Grbl looks for data. For a complete wipe, please use the Arduino
IDE’s EEPROM clear example.
- Refactored the restore and wipe functions in settings.c to
accommodate the new commands.
- New restore setting defaults command. Only wipes ‘$$’ setting in
EEPROM and reloads them based on the defaults used when Grbl was
compiled. Used with a `$RST` command
NOTE: `$RST` is intentionally not listed in the Grbl ‘$’ help message.
- Updated new homing cycle to error out when a pull-off motion detects
the limit is still active.
- Created a limits_get_state() function to centralize it. It reports
state as a bit-wise booleans according to axis numbering.
- Updated the print uint8 functions. Generalized it to allow both base2
and base10 printouts, while allowing base2 prints with N_AXIS digits
for limit state status reports. Doing this saved about 100bytes of
flash as well.
- Applied CoreXY status reporting bug fix by @phd0. Thanks!
- Critical fix for M0 program pause. Due to its recent change, it would
cause Grbl to suspend but wouldn’t notify the user of why Grbl was not
doing anything. The state would show IDLE and a cycle start would
resume it. Grbl now enters a HOLD state to better indicate the state
change.
- Critical fix for M2 and M30 program end. As with M0, the state
previously would show IDLE while suspended. Grbl now does not suspend
upon program end and leaves job control to the GUI. Grbl simply reports
a `[Pgm End]` as a feedback message and resets certain g-code modes.
- M2/30 g-code reseting fix. Previously Grbl would soft-reset after an
M2/30, but this was not complaint to the (linuxcnc) g-code standard. It
simply resets [G1,G17,G90,G94,G40,G54,M5,M9,M48] and keeps all other
modes the same.
- M0/M2/M30 check-mode fix. It now does not suspend the machine during
check-mode.
- Minor bug fix related to commands similar to G90.1, but not G90.1,
not reporting an unsupported command.
- Homing cycle refactoring. To help reduce the chance of users
misunderstanding their limit switch wiring, Grbl only moves a short
distance for the locate cycles only. In addition, the homing cycle
pulls-off the limit switch by the pull-off distance to re-engage and
locate home. This should improve its accuracy.
- HOMING_FORCE_ORIGIN now sets the origin to the pull-off location,
rather than where the limit switch was triggered.
- Updated default junction deviation to 0.01mm. Recent tests showed
that this improves Grbl’s cornering behavior a bit.
- Added the ShapeOko3 defaults.
- Added new feedback message `[Pgm End]` for M2/30 notification.
- Limit pin reporting is now a $10 status report option. Requested by
OEMs to help simplify support troubleshooting.
- Commit history added to repo, as an easier way for people to see view
the changes over time.
- Grbl logo copyright license added. All rights reserved with regards
to the Grbl logo.
- G2/3 full circles would sometime not execute. The problem was due to
numerical round-off of a trig calculation. Added a machine epsilon
define to help detect and correct for this problem. Tested and should
not effect general operation of arcs.
