- Variable spindle speed output as a configuration option. Thanks
@EliteEng! When enabled, the Z-limit (D11) and spindle enable(D12) pins
switch to allow access to the hardware PWM output on pin D11.
Otherwise, everything should work as it does.
- Removed option for inverting the spindle and coolant enable pins.
This is a safety hazard, especially for the spindle. When Grbl
initializes, all pins are momentarily low until it finishes booting. If
an invert is enabled, this means the spindles can be energized briefly
during this time. If users need signal inversion, it’s recommended to
just wire in an inversion circuit instead.
- Cleared out references to spindle variable output in terms of step
signal. This isn’t complete and requires more deliberation before
installing.
- Cleared up and cleaned up some code and config comments.
- Homing travel calculations fixed. It was computing the min travel
rather than max.
- Auto-start disable and pausing after spindle or dwell commands.
Related to plan_synchronize() function call. Now fixed, but still need
to work on the system state.
- Pushed a fix to make this branch more Arduino IDE compatible. Removed
extern call in nuts_bolts.c
- Updated the stepper configuration option of enabling or disabling the
new Adaptive Multi-Axis Step Smoothing Algorithm. Now works either way.
- Updated some copyright info.
(All v0.8 features installed. Still likely buggy, but now thourough
testing will need to start to squash them all. As soon as we're done,
this will be pushed to master and v0.9 development will be started.
Please report ANY issues to us so we can get this rolled out ASAP.)
- User startup script! A user can now save one (up to 5 as compile-time
option) block of g-code in EEPROM memory. This will be run everytime
Grbl resets. Mainly to be used as a way to set your preferences, like
G21, G54, etc.
- New dry run and check g-code switches. Dry run moves ALL motions at
rapids rate ignoring spindle, coolant, and dwell commands. For rapid
physical proofing of your code. The check g-code switch ignores all
motion and provides the user a way to check if there are any errors in
their program that Grbl may not like.
- Program restart! (sort of). Program restart is typically an advanced
feature that allows users to restart a program mid-stream. The check
g-code switch can perform this feature by enabling the switch at the
start of the program, and disabling it at the desired point with some
minimal changes.
- New system state variable. This state variable tracks all of the
different state processes that Grbl performs, i.e. cycle start, feed
hold, homing, etc. This is mainly for making managing of these task
easier and more clear.
- Position lost state variable. Only when homing is enabled, Grbl will
refuse to move until homing is completed and position is known. This is
mainly for safety. Otherwise, it will let users fend for themselves.
- Moved the default settings defines into config.h. The plan is to
eventually create a set of config.h's for particular as-built machines
to help users from doing it themselves.
- Moved around misc defines into .h files. And lots of other little
things.
NOTE: Another incremental update. Likely buggy, still a ways to go
before everything is installed, such as startup blocks.
- Changed the '$' command to print help. '$$' now prints Grbl settings.
The help now instructs the user of runtime commands, switch toggling,
homing, etc. Jogging will be added to these in v0.9.
- Added switches: block delete, opt stop, and single block mode.
- Now can print the g-code parser state and persistent parameters
(coord sys) to view what Grbl has internally.
- Made the gc struct in the g-code parser global to be able to print
the states. Also moved coordinate system tracking from sys to gc struct.
- Changed up the welcome flag and updated version to v0.8c.
- Removed spindle speed from gcode parser. Not used.
- Added coolant control! Flood control (M8) functions on analog pin 0.
Mist control (M7) is compile-time optional and is on analog pin 1. (Use
only if you have multiple coolants on your system). Based on work by
@openpnp.
- Fixed some variable assignments in spindle control.
- G54 work coordinate system support. Up to 6 work coordinate systems
(G54-G59) available as a compile-time option.
- G10 command added to set work coordinate offsets from machine
position.
- G92/G92.1 position offsets and cancellation support. Properly follows
NIST standard rules with other systems.
- G53 absolute override now works correctly with new coordinate systems.
- Revamped g-code parser with robust error checking. Providing user
feedback with bad commands. Follows NIST standards.
- Planner module slightly changed to only expected position movements
in terms of machine coordinates only. This was to simplify coordinate
system handling, which is done solely by the g-code parser.
- Upon grbl system abort, machine position and work positions are
retained, while G92 offsets are reset per NIST standards.
- Compiler compatibility update for _delay_us().
- Updated README.
- ALPHA status. - Multitasking ability with run-time command executions
for real-time control and feedback. - Decelerating feed hold and resume
during operation. - System abort/reset, which immediately kills all
movement and re-initializes grbl. - Re-structured grbl to easily allow
for new features: Status reporting, jogging, backlash compensation. (To
be completed in the following releases.) - Resized TX/RX serial buffers
(32/128 bytes) - Increased planner buffer size to 20 blocks. - Updated
documentation.
