- New pin state realtime reporting feature. Instead of `Lim:000` for
limit state reports, the new feature shows `Pin:000|0|0000`, or
something similar. The `|` delimited fields indicate xyz limits, probe,
and control pin states, where 0 is always not triggered, and 1 is
triggered. Invert masks ARE accounted for.
Each field may be enabled or disabled via the `$10` status report
setting. The probe and control pin flags are bits 5 and 6, respectively.
- Remove the now deprecated `REPORT_CONTROL_PIN_STATE` option in
config.h
- The old limit pin reports `Lim:000` may be re-enabled by commenting
out `REPORT_ALL_PIN_STATES` in config.h.
- Incremented the version letter (v1.0c) to indicate the change in
reporting style.
- Replaced all bit_true_atomic and bit_false_atomic macros with
function calls. This saved a couple hundred bytes of flash.
- G38.x was not printing correctly in the $G g-code state reports. Now
fixed.
- When investigating the above issue, it was noticed that G38.x
wouldn’t show at all, but instead a G0 would be printed. This was
unlike the v0.9j master build. It turned out volatile variables do not
like to be defined inside a C struct. These are undefined on how to be
handled. Once pulled out, all weird issues went away.
- Also changed two ‘sizeof()’ statements in the mc_probe() and
probe_state_monitor() functions to be more robust later on.
- Updated the commit logs to individual files for each minor release.
Forgot to update the generating script to account for this.
- G38.x was not printing correctly in the $G g-code state reports. Now
fixed.
- Potential bug regarding volatile variables inside a struct. It has
never been a problem in v0.9, but ran into this during v1.0
development. Just to be safe, the fixes are applied here.
- Updated pre-built firmwares with these two bug fixes.
- G28 and G30’s behavior has been updated from the old NIST g-code
standard to LinuxCNC’s. Previously when an intermediate motion was
programmed, the NIST standard would move all axes to the final G28/30
stored coordinates. LinuxCNC states it only moves the axes specified in
the command.
For example, suppose G28’s stored position is (x,y,z) = (1,2,3) for
simplicity, and we want to do an automated z-axis tool retraction and
then park at the x,y location. `G28 G91 Z5` will first move the Z axis
5mm(or inches) up, then move Z to position 3 in machine coordinates.
Next, the command `G28 G91 X0 Y0` would skip the intermediate move
since distance is zero, but then move only the x and y axes to machine
coordinates 1 and 2, respectively. The z-axis wouldn’t move in this
case, since it wasn’t specified.
This change is intended to make Grbl more LinuxCNC compatible while
making commands, like the shown tool retraction, much easier to
implement.
- Version bump requested by OEMs to easily determine whether the
firmware supports the new EEPROM reset feature. Other than that, no
significant changes.
- Tweaked the previous EEPROM restore implementation and added new
functionality.
- `$RST=$` restores the `$$` grbl settings back to firmware defaults,
which are set when compiled.
- `$RST=#` restores the `$#` parameters in EEPROM. At times it’s useful
to clear these and start over, rather than manually writing each entry.
-`$RST=*` wipe all of the data in EEPROM that Grbl uses and restores
them to defaults. This includes `$$` settings, `$#` parameters, `$N`
startup lines, and `$i` build info string.
NOTE: This doesn’t write zeros throughout the EEPROM. It only writes
where Grbl looks for data. For a complete wipe, please use the Arduino
IDE’s EEPROM clear example.
- Refactored the restore and wipe functions in settings.c to
accommodate the new commands.
- New restore setting defaults command. Only wipes ‘$$’ setting in
EEPROM and reloads them based on the defaults used when Grbl was
compiled. Used with a `$RST` command
NOTE: `$RST` is intentionally not listed in the Grbl ‘$’ help message.
- Updated new homing cycle to error out when a pull-off motion detects
the limit is still active.
- Created a limits_get_state() function to centralize it. It reports
state as a bit-wise booleans according to axis numbering.
- Updated the print uint8 functions. Generalized it to allow both base2
and base10 printouts, while allowing base2 prints with N_AXIS digits
for limit state status reports. Doing this saved about 100bytes of
flash as well.
- Applied CoreXY status reporting bug fix by @phd0. Thanks!
- Critical fix for M0 program pause. Due to its recent change, it would
cause Grbl to suspend but wouldn’t notify the user of why Grbl was not
doing anything. The state would show IDLE and a cycle start would
resume it. Grbl now enters a HOLD state to better indicate the state
change.
- Critical fix for M2 and M30 program end. As with M0, the state
previously would show IDLE while suspended. Grbl now does not suspend
upon program end and leaves job control to the GUI. Grbl simply reports
a `[Pgm End]` as a feedback message and resets certain g-code modes.
- M2/30 g-code reseting fix. Previously Grbl would soft-reset after an
M2/30, but this was not complaint to the (linuxcnc) g-code standard. It
simply resets [G1,G17,G90,G94,G40,G54,M5,M9,M48] and keeps all other
modes the same.
- M0/M2/M30 check-mode fix. It now does not suspend the machine during
check-mode.
- Minor bug fix related to commands similar to G90.1, but not G90.1,
not reporting an unsupported command.
- Homing cycle refactoring. To help reduce the chance of users
misunderstanding their limit switch wiring, Grbl only moves a short
distance for the locate cycles only. In addition, the homing cycle
pulls-off the limit switch by the pull-off distance to re-engage and
locate home. This should improve its accuracy.
- HOMING_FORCE_ORIGIN now sets the origin to the pull-off location,
rather than where the limit switch was triggered.
- Updated default junction deviation to 0.01mm. Recent tests showed
that this improves Grbl’s cornering behavior a bit.
- Added the ShapeOko3 defaults.
- Added new feedback message `[Pgm End]` for M2/30 notification.
- Limit pin reporting is now a $10 status report option. Requested by
OEMs to help simplify support troubleshooting.
- Commit history added to repo, as an easier way for people to see view
the changes over time.
- Grbl logo copyright license added. All rights reserved with regards
to the Grbl logo.
- G2/3 full circles would sometime not execute. The problem was due to
numerical round-off of a trig calculation. Added a machine epsilon
define to help detect and correct for this problem. Tested and should
not effect general operation of arcs.
