- Maximum velocity for each axis is now configurable in settings. All
rapids/seek move at these maximums. All feed rates(including rapids)
may be limited and scaled down so that no axis does not exceed their
limits.
- Moved around auto-cycle start. May change later, but mainly to ensure
the planner buffer is completely full before cycle starting a streaming
program. Otherwise it should auto-start when there is a break in the
serial stream.
- Reverted old block->max_entry_speed_sqr calculations. Feedrate
overrides not close to ready at all.
- Fixed intermittent slow trailing steps for some triangle velocity
profile moves. The acceleration tick counter updating was corrected to
be exact for that particular transition. Should be ok for normal
trapezoidal profiles.
- Fixed the Timer0 disable after a step pulse falling edge. Thanks
@blinkenlight!
- Added Grbl state (Idle, Running, Queued, Hold, etc) to the real-time
status reporting feature as feedback to the user of what Grbl is doing.
Updated the help message to reflect this change.
- Removed switches (dry run, block delete, single block mode). To keep
Grbl simple and not muddled up from things that can easily be taken
care of by an external interface, these were removed.
- Check g-code mode was retained, but the command was moved to '$C'
from '$S0'.
- Fixed a minor issue where the seek rates would not immediately be
used and only would after a reset. Should update live now.
- A full circle IJ offset CCW arc would not do anything. Fixed bug via
a simple if-then statement.
- Radius mode tweaks to check for negative value in sqrt() rather than
isnan() it. Error report updated to indicate what actually happened.
- Removed the dry run switch. It was getting overly complicated for
what it needed to do. In practice, single block mode and feed rate
overrides (coming in next release) does a much better job with dry runs
than 'dry run'.
- Trimmed all of Grbl's messages from help, status, feedback to
settings. Saved 0.6KB+ of flash space that could be used for v0.9
features.
- Removed some settings inits when set. Will depend on user to power
cycle to get some of these to reload.
- Fixed a bug with settings version not re-writing old settings, when
it should. Thanks Alden!
- To make managing the code easier and to help ensure a user starts
with a fresh reset, the functionality of check g-code and dry run has
been changed to automatically perform a soft reset when toggled off.
Position will not be lost, unless there is a cycle active. Feed hold
before toggling off it needed.
This is mainly a safety issue. If a user dry runs a program and kills
it mid-program, and then restarts it thinking to run it as normal, the
g-code modes that we're set may not be what they expect, and very bad
things can happen.
- NOTE: Grbl is at 83.5% of flash capacity. Not a lot of room left, but
I think we can squeeze in some more!
- Added a purge buffer (and lock) command. This is an advanced option
to clear any queued blocks in the buffer in the event of system
position being lost or homed. These queued blocks will likely not move
correctly if not purged. In typical use, the purging command releases
the homing axes lock in case a user need to move the axes off their
hard limit switches, but position is not guaranteed. Homing is advised
immediately after.
- Created a system-wide sync current position function. Cleans up some
of the repetitive tasks in various places in the code that do the same
thing.
- Removed the clear all switches command '$S'. Not really needed and
helped clean up a sync call.
- Other minor tweaks. Readme updated slightly..
(All v0.8 features installed. Still likely buggy, but now thourough
testing will need to start to squash them all. As soon as we're done,
this will be pushed to master and v0.9 development will be started.
Please report ANY issues to us so we can get this rolled out ASAP.)
- User startup script! A user can now save one (up to 5 as compile-time
option) block of g-code in EEPROM memory. This will be run everytime
Grbl resets. Mainly to be used as a way to set your preferences, like
G21, G54, etc.
- New dry run and check g-code switches. Dry run moves ALL motions at
rapids rate ignoring spindle, coolant, and dwell commands. For rapid
physical proofing of your code. The check g-code switch ignores all
motion and provides the user a way to check if there are any errors in
their program that Grbl may not like.
- Program restart! (sort of). Program restart is typically an advanced
feature that allows users to restart a program mid-stream. The check
g-code switch can perform this feature by enabling the switch at the
start of the program, and disabling it at the desired point with some
minimal changes.
- New system state variable. This state variable tracks all of the
different state processes that Grbl performs, i.e. cycle start, feed
hold, homing, etc. This is mainly for making managing of these task
easier and more clear.
- Position lost state variable. Only when homing is enabled, Grbl will
refuse to move until homing is completed and position is known. This is
mainly for safety. Otherwise, it will let users fend for themselves.
- Moved the default settings defines into config.h. The plan is to
eventually create a set of config.h's for particular as-built machines
to help users from doing it themselves.
- Moved around misc defines into .h files. And lots of other little
things.
NOTE: Another incremental update. Likely buggy, still a ways to go
before everything is installed, such as startup blocks.
- Changed the '$' command to print help. '$$' now prints Grbl settings.
The help now instructs the user of runtime commands, switch toggling,
homing, etc. Jogging will be added to these in v0.9.
- Added switches: block delete, opt stop, and single block mode.
- Now can print the g-code parser state and persistent parameters
(coord sys) to view what Grbl has internally.
- Made the gc struct in the g-code parser global to be able to print
the states. Also moved coordinate system tracking from sys to gc struct.
- Changed up the welcome flag and updated version to v0.8c.
- Removed spindle speed from gcode parser. Not used.
- Added acceleration to the homing routine.
- Homing now accounts for different step rates when moving multiple
axes without exceeding acceleration limits.
- Homing now updates all internal positioning variables to machine zero
after completion.
- "Poor-man's" debounce delay added.
- Updated the delay_us() function to perform faster and more accurate
microsecond delays. Previously, the single increments would add
noticeable time drift for larger delays.
- Fix a bug in the stepper.c prescalar calculations that was changed in
the last commit.
- Other minor fixes.
- G54 work coordinate system support. Up to 6 work coordinate systems
(G54-G59) available as a compile-time option.
- G10 command added to set work coordinate offsets from machine
position.
- G92/G92.1 position offsets and cancellation support. Properly follows
NIST standard rules with other systems.
- G53 absolute override now works correctly with new coordinate systems.
- Revamped g-code parser with robust error checking. Providing user
feedback with bad commands. Follows NIST standards.
- Planner module slightly changed to only expected position movements
in terms of machine coordinates only. This was to simplify coordinate
system handling, which is done solely by the g-code parser.
- Upon grbl system abort, machine position and work positions are
retained, while G92 offsets are reset per NIST standards.
- Compiler compatibility update for _delay_us().
- Updated README.
- Program stop support (M0,M1*,M2,M30*). *Optional stop to be done.
*Pallet shuttle not supported.
- Work position is set equal to machine position upon reset, as
according to NIST RS274-NGC guidelines. G92 is disabled.
- Renamed mc_set_current_position() to mc_set_coordinate_offset().
- Fixed bug in plan_synchronize(). Would exit right before last step is
finished and caused issues with program stops. Now fixed.
- Spindle now stops upon a run-time abort command.
- Updated readme and misc upkeeping.
