ManuelW/grbl-LPC-CoreXY
1
0
Fork 0
Code Issues Pull Requests Releases 1 Wiki Activity

v1.1f. Parking override control. Spindle enable pin option.

Browse Source 
[ver] v1.1f update due to tweaks to interface from new parking override
control.

[new] Parking motion override control via new `M56 P0` and `M56 P1`
command, which disables and enables the parking motion, respectively.
Requires ENABLE_PARKING_OVERRIDE_CONTROL and PARKING_ENABLE enabled in
config.h. Primarily for OEMs.

[new] `M56` appears in the $G report when enabled.

[new] Five new build info identification letters. Some were missing and
a couple are new. Updated the CSV and documentation to reflect these
new items.

[new] Spindle enable pin configuration option to alter its behavior
based on how certain lasers work. By default, Grbl treats the enable
pin separately and leaves it on when S is 0. The new option turns the
enable pin on and off with S>0 and S=0. This only is in effect when a
user enables the USE_SPINDLE_DIR_AS_ENABLE_PIN option.

[fix] M4 is now allowed to work when USE_SPINDLE_DIR_AS_ENABLE_PIN is
enabled. Previously this was blocked and was problematic for laser
folks using M4.

[fix] Properly declared system variables as extern. Not sure how that
went unnoticed or why it worked up until now but it has.

[fix] EXTREMELY RARE. When AMASS is intentionally disabled and sent a
motion command that is _one step_ in length, Grbl would not actuate the
step due to numerical round-off. Applied a fix to prevent the round-off
issue.

[fix] Added a compile-time check for AMASS settings to make sure that
the numerical round-off issue doesn’t effect it. This would only happen
if someone set AMASS max levels to zero. It does not effect AMASS with
its current defaults.

[fix] Wrapped the mc_parking_motion() function in an ifdef for porting
purposes.

[fix] Fixed an issue when in inverse time mode and G0’s would require a
F word. This was not correct.

[fix] Added a note in the defaults.h file that MAX_TRAVEL values must
be positive. Some users were setting this negative and it was causing
issues.
This commit is contained in:
chamnit
2017-01-28 17:13:06 -07:00
parent 67ab9280d9
commit e455764079
19 changed files with 259 additions and 102 deletions
Download Patch File Download Diff File Expand all files Collapse all files

17
grbl/config.h
View File

@ -353,12 +353,20 @@
// preserve I/O pins. For certain setups, these may need to be separate pins. This configure option uses
// the spindle direction pin(D13) as a separate spindle enable pin along with spindle speed PWM on pin D11.
// NOTE: This configure option only works with VARIABLE_SPINDLE enabled and a 328p processor (Uno).
// NOTE: With no direction pin, the spindle clockwise M4 g-code command will be removed. M3 and M5 still work.
// NOTE: Without a direction pin, M4 will not have a pin output to indicate a difference with M3.
// NOTE: BEWARE! The Arduino bootloader toggles the D13 pin when it powers up. If you flash Grbl with
// a programmer (you can use a spare Arduino as "Arduino as ISP". Search the web on how to wire this.),
// this D13 LED toggling should go away. We haven't tested this though. Please report how it goes!
// #define USE_SPINDLE_DIR_AS_ENABLE_PIN // Default disabled. Uncomment to enable.
// Alters the behavior of the spindle enable pin with the USE_SPINDLE_DIR_AS_ENABLE_PIN option . By default,
// Grbl will not disable the enable pin if spindle speed is zero and M3/4 is active, but still sets the PWM
// output to zero. This allows the users to know if the spindle is active and use it as an additional control
// input. However, in some use cases, user may want the enable pin to disable with a zero spindle speed and
// re-enable when spindle speed is greater than zero. This option does that.
// NOTE: Requires USE_SPINDLE_DIR_AS_ENABLE_PIN to be enabled.
// #define SPINDLE_ENABLE_OFF_WITH_ZERO_SPEED // Default disabled. Uncomment to enable.
// With this enabled, Grbl sends back an echo of the line it has received, which has been pre-parsed (spaces
// removed, capitalized letters, no comments) and is to be immediately executed by Grbl. Echoes will not be
// sent upon a line buffer overflow, but should for all normal lines sent to Grbl. For example, if a user
@ -563,6 +571,13 @@
#define PARKING_PULLOUT_INCREMENT 5.0 // Spindle pull-out and plunge distance in mm. Incremental distance.
// Must be positive value or equal to zero.
// Enables a special set of M-code commands that enables and disables the parking motion.
// These are controlled by `M56`, `M56 P1`, or `M56 Px` to enable and `M56 P0` to disable.
// The command is modal and will be set after a planner sync. Since it is g-code, it is
// executed in sync with g-code commands. It is not a real-time command.
// NOTE: PARKING_ENABLE is required.
// #define ENABLE_PARKING_OVERRIDE_CONTROL // Default disabled. Uncomment to enable
// This option will automatically disable the laser during a feed hold by invoking a spindle stop
// override immediately after coming to a stop. However, this also means that the laser still may
// be reenabled by disabling the spindle stop override, if needed. This is purely a safety feature