Merge pull request #193 from bungao/soft_limts

integrating soft limits

limits.c

@@ -73,6 +73,7 @@ ISR(LIMIT_INT_vect)
   if (sys.state != STATE_ALARM) { 
     if (bit_isfalse(sys.execute,EXEC_ALARM)) {
       mc_reset(); // Initiate system kill.
+      report_alarm_message(ALARM_HARD_LIMIT);
       sys.execute |= EXEC_CRIT_EVENT; // Indicate hard limit critical event
     }
   }

motion_control.c

@@ -35,6 +35,7 @@
 #include "planner.h"
 #include "limits.h"
 #include "protocol.h"
+#include "report.h"
 
 // Execute linear motion in absolute millimeter coordinates. Feed rate given in millimeters/second
 // unless invert_feed_rate is true. Then the feed_rate means that the motion should be completed in
@@ -49,9 +50,21 @@
 // backlash segment(s).
 void mc_line(float x, float y, float z, float feed_rate, uint8_t invert_feed_rate)
 {
-  // TODO: Perform soft limit check here. Just check if the target x,y,z values are outside the 
+  // TO TEST: Perform soft limit check here. Just check if the target x,y,z values are outside the 
   // work envelope. Should be straightforward and efficient. By placing it here, rather than in 
   // the g-code parser, it directly picks up motions from everywhere in Grbl.
+  if (bit_istrue(settings.flags,BITFLAG_SOFT_LIMIT_ENABLE)) {
+    if(  (x> settings.mm_soft_limit[X_AXIS])||(y>settings.mm_soft_limit[Y_AXIS])||(z>settings.mm_soft_limit[Z_AXIS])) {
+            if (sys.state != STATE_ALARM) { 
+                if (bit_isfalse(sys.execute,EXEC_ALARM)) {
+                    mc_reset(); // Initiate system kill.
+                    report_alarm_message(ALARM_SOFT_LIMIT);
+                    sys.state = STATE_ALARM;
+                    sys.execute |= EXEC_CRIT_EVENT; // Indicate hard limit critical event 
+                }
+            }
+        }
+  }
 
   // If in check gcode mode, prevent motion by blocking planner.
   if (sys.state == STATE_CHECK_MODE) { return; }

protocol.c

@@ -105,9 +105,7 @@ void protocol_execute_runtime()
     if (rt_exec & (EXEC_ALARM | EXEC_CRIT_EVENT)) {      
       sys.state = STATE_ALARM; // Set system alarm state
       
-      // Critical event. Only hard limit qualifies. Update this as new critical events surface.
       if (rt_exec & EXEC_CRIT_EVENT) { 
-        report_alarm_message(ALARM_HARD_LIMIT); 
         report_feedback_message(MESSAGE_CRITICAL_EVENT);
         bit_false(sys.execute,EXEC_RESET); // Disable any existing reset
         do { 

report.c

@@ -88,6 +88,8 @@ void report_alarm_message(int8_t alarm_code)
     printPgmString(PSTR("Hard limit")); break;
     case ALARM_ABORT_CYCLE: 
     printPgmString(PSTR("Abort during cycle")); break;
+    case ALARM_SOFT_LIMIT: 
+    printPgmString(PSTR("Soft Limit")); break;
   }
   printPgmString(PSTR(". MPos?\r\n"));
   delay_ms(500); // Force delay to ensure message clears serial write buffer.
@@ -172,7 +174,11 @@ void report_grbl_settings() {
   printPgmString(PSTR(" (homing feed, mm/min)\r\n$23=")); printFloat(settings.homing_seek_rate);
   printPgmString(PSTR(" (homing seek, mm/min)\r\n$24=")); printInteger(settings.homing_debounce_delay);
   printPgmString(PSTR(" (homing debounce, msec)\r\n$25=")); printFloat(settings.homing_pulloff);
-  printPgmString(PSTR(" (homing pull-off, mm)\r\n")); 
+  printPgmString(PSTR(" (homing pull-off, mm)\r\n$26=")); printFloat(settings.mm_soft_limit[X_AXIS]);
+  printPgmString(PSTR(" (x, max travel)\r\n$27=")); printFloat(settings.mm_soft_limit[Y_AXIS]);
+  printPgmString(PSTR(" (y, max travel)\r\n$28=")); printFloat(settings.mm_soft_limit[Z_AXIS]);
+  printPgmString(PSTR(" (z, max travel)\r\n$29=")); printInteger(bit_istrue(settings.flags,BITFLAG_SOFT_LIMIT_ENABLE));
+  printPgmString(PSTR(" (soft limits enabled, bool)\r\n"));  
 }
 
 

report.h

@@ -39,6 +39,7 @@
 // Define Grbl alarm codes. Less than zero to distinguish alarm error from status error.
 #define ALARM_HARD_LIMIT -1
 #define ALARM_ABORT_CYCLE -2
+#define ALARM_SOFT_LIMIT -3
 
 // Define Grbl feedback message codes.
 #define MESSAGE_CRITICAL_EVENT 1

settings.c

@@ -200,6 +200,13 @@ uint8_t settings_store_global_setting(int parameter, float value) {
     case 23: settings.homing_seek_rate = value; break;
     case 24: settings.homing_debounce_delay = round(value); break;
     case 25: settings.homing_pulloff = value; break;
+    case 26: case 27: case 28:
+    if (value <= 0.0) { return(STATUS_SETTING_VALUE_NEG); } 
+      settings.mm_soft_limit[parameter-26] = value; break;
+    case 29:
+    if (value) { settings.flags |= BITFLAG_SOFT_LIMIT_ENABLE; }
+      else { settings.flags &= ~BITFLAG_SOFT_LIMIT_ENABLE; }
+      break;
     default: 
       return(STATUS_INVALID_STATEMENT);
   }

settings.h

@@ -37,6 +37,7 @@
 #define BITFLAG_INVERT_ST_ENABLE   bit(2)
 #define BITFLAG_HARD_LIMIT_ENABLE  bit(3)
 #define BITFLAG_HOMING_ENABLE      bit(4)
+#define BITFLAG_SOFT_LIMIT_ENABLE  bit(5)
 
 // Define EEPROM memory address location values for Grbl settings and parameters
 // NOTE: The Atmega328p has 1KB EEPROM. The upper half is reserved for parameters and
@@ -74,7 +75,7 @@ typedef struct {
   uint8_t stepper_idle_lock_time; // If max value 255, steppers do not disable.
   uint8_t decimal_places;
   float max_velocity[N_AXIS];
-//  float mm_soft_limit[N_AXIS];
+  float mm_soft_limit[N_AXIS];
 //  uint8_t status_report_mask; // Mask to indicate desired report data.
 } settings_t;
 extern settings_t settings;