Initial line number reporting

gcode.c

@@ -106,6 +106,7 @@ uint8_t gc_execute_line(char *line)
   float target[N_AXIS];
   clear_vector(target); // XYZ(ABC) axes parameters.
 
+  uint32_t line_number = 0;
   gc.arc_radius = 0;
   clear_vector(gc.arc_offset); // IJK Arc offsets are incremental. Value of zero indicates no change.
 
@@ -220,7 +221,7 @@ uint8_t gc_execute_line(char *line)
   char_counter = 0;
   while(next_statement(&letter, &value, line, &char_counter)) {
     switch(letter) {
-      case 'G': case 'M': case 'N': break; // Ignore command statements and line numbers
+      case 'G': case 'M': break; // Ignore command statements and line numbers
       case 'F': 
         if (value <= 0) { FAIL(STATUS_INVALID_STATEMENT); } // Must be greater than zero
         if (gc.inverse_feed_rate_mode) {
@@ -231,6 +232,7 @@ uint8_t gc_execute_line(char *line)
         break;
       case 'I': case 'J': case 'K': gc.arc_offset[letter-'I'] = to_millimeters(value); break;
       case 'L': l = trunc(value); break;
+      case 'N': line_number = trunc(value); break;
       case 'P': p = value; break;                    
       case 'R': gc.arc_radius = to_millimeters(value); break;
       case 'S': 
@@ -330,7 +332,7 @@ uint8_t gc_execute_line(char *line)
             target[idx] = gc.position[idx];
           }
         }
-        mc_line(target, -1.0, false);
+        mc_line(target, -1.0, false, line_number);
       }
       // Retreive G28/30 go-home position data (in machine coordinates) from EEPROM
       float coord_data[N_AXIS];
@@ -339,7 +341,7 @@ uint8_t gc_execute_line(char *line)
       } else {
         if (!settings_read_coord_data(SETTING_INDEX_G30,coord_data)) { return(STATUS_SETTING_READ_FAIL); }
       }
-      mc_line(coord_data, -1.0, false); 
+      mc_line(coord_data, -1.0, false, line_number); 
       memcpy(gc.position, coord_data, sizeof(coord_data)); // gc.position[] = coord_data[];
       axis_words = 0; // Axis words used. Lock out from motion modes by clearing flags.
       break;
@@ -410,7 +412,7 @@ uint8_t gc_execute_line(char *line)
         break;
       case MOTION_MODE_SEEK:
         if (!axis_words) { FAIL(STATUS_INVALID_STATEMENT);} 
-        else { mc_line(target, -1.0, false); }
+        else { mc_line(target, -1.0, false, line_number); }
         break;
       case MOTION_MODE_LINEAR:
         // TODO: Inverse time requires F-word with each statement. Need to do a check. Also need
@@ -418,7 +420,7 @@ uint8_t gc_execute_line(char *line)
         // and after an inverse time move and then check for non-zero feed rate each time. This
         // should be efficient and effective.
         if (!axis_words) { FAIL(STATUS_INVALID_STATEMENT);} 
-        else { mc_line(target, (gc.inverse_feed_rate_mode) ? inverse_feed_rate : gc.feed_rate, gc.inverse_feed_rate_mode); }
+        else { mc_line(target, (gc.inverse_feed_rate_mode) ? inverse_feed_rate : gc.feed_rate, gc.inverse_feed_rate_mode, line_number); }
         break;
       case MOTION_MODE_CW_ARC: case MOTION_MODE_CCW_ARC:
         // Check if at least one of the axes of the selected plane has been specified. If in center 
@@ -442,7 +444,7 @@ uint8_t gc_execute_line(char *line)
           // Trace the arc
           mc_arc(gc.position, target, gc.arc_offset, gc.plane_axis_0, gc.plane_axis_1, gc.plane_axis_2,
             (gc.inverse_feed_rate_mode) ? inverse_feed_rate : gc.feed_rate, gc.inverse_feed_rate_mode,
-            gc.arc_radius, isclockwise);
+            gc.arc_radius, isclockwise, line_number);
         }            
         break;
     }

limits.c

@@ -157,7 +157,7 @@ void limits_go_home(uint8_t cycle_mask, bool approach, float homing_rate)
   
   // Perform homing cycle. Planner buffer should be empty, as required to initiate the homing cycle.
   uint8_t limit_state;
-  plan_buffer_line(target, homing_rate, false); // Bypass mc_line(). Directly plan homing motion.
+  plan_buffer_line(target, homing_rate, false, HOMING_CYCLE_LINE_NUMBER); // Bypass mc_line(). Directly plan homing motion.
   st_prep_buffer(); // Prep first segment from newly planned block.
   st_wake_up(); // Initiate motion
   do {

motion_control.c

@@ -39,7 +39,7 @@
 // segments, must pass through this routine before being passed to the planner. The seperation of
 // mc_line and plan_buffer_line is done primarily to place non-planner-type functions from being
 // in the planner and to let backlash compensation or canned cycle integration simple and direct.
-void mc_line(float *target, float feed_rate, uint8_t invert_feed_rate)
+void mc_line(float *target, float feed_rate, uint8_t invert_feed_rate, uint32_t line_number)
 {
   // If enabled, check for soft limit violations. Placed here all line motions are picked up
   // from everywhere in Grbl.
@@ -68,7 +68,7 @@ void mc_line(float *target, float feed_rate, uint8_t invert_feed_rate)
     else { break; }
   } while (1);
 
-  plan_buffer_line(target, feed_rate, invert_feed_rate);
+  plan_buffer_line(target, feed_rate, invert_feed_rate, line_number);
 
   // If idle, indicate to the system there is now a planned block in the buffer ready to cycle 
   // start. Otherwise ignore and continue on.
@@ -84,7 +84,7 @@ void mc_line(float *target, float feed_rate, uint8_t invert_feed_rate)
 // of each segment is configured in settings.arc_tolerance, which is defined to be the maximum normal
 // distance from segment to the circle when the end points both lie on the circle.
 void mc_arc(float *position, float *target, float *offset, uint8_t axis_0, uint8_t axis_1, 
-  uint8_t axis_linear, float feed_rate, uint8_t invert_feed_rate, float radius, uint8_t isclockwise)
+  uint8_t axis_linear, float feed_rate, uint8_t invert_feed_rate, float radius, uint8_t isclockwise, uint32_t line_number)
 {      
   float center_axis0 = position[axis_0] + offset[axis_0];
   float center_axis1 = position[axis_1] + offset[axis_1];
@@ -180,14 +180,14 @@ void mc_arc(float *position, float *target, float *offset, uint8_t axis_0, uint8
       arc_target[axis_0] = center_axis0 + r_axis0;
       arc_target[axis_1] = center_axis1 + r_axis1;
       arc_target[axis_linear] += linear_per_segment;
-      mc_line(arc_target, feed_rate, invert_feed_rate);
+      mc_line(arc_target, feed_rate, invert_feed_rate, line_number);
       
       // Bail mid-circle on system abort. Runtime command check already performed by mc_line.
       if (sys.abort) { return; }
     }
   }
   // Ensure last segment arrives at target location.
-  mc_line(target, feed_rate, invert_feed_rate);
+  mc_line(target, feed_rate, invert_feed_rate, line_number);
 }
 
 
@@ -273,7 +273,7 @@ void mc_homing_cycle()
 
   sys.state = STATE_IDLE; // Set system state to IDLE to complete motion and indicate homed.
 
-  mc_line(pulloff_target, settings.homing_seek_rate, false);
+  mc_line(pulloff_target, settings.homing_seek_rate, false, HOMING_CYCLE_LINE_NUMBER); 
   st_cycle_start(); // Move it. Nothing should be in the buffer except this motion. 
   plan_synchronize(); // Make sure the motion completes.
                       // NOTE: Stepper idle lock resumes normal functionality after cycle.

motion_control.h

@@ -22,18 +22,19 @@
 #ifndef motion_control_h
 #define motion_control_h
 
+#define HOMING_CYCLE_LINE_NUMBER 1000000000
 
 // Execute linear motion in absolute millimeter coordinates. Feed rate given in millimeters/second
 // unless invert_feed_rate is true. Then the feed_rate means that the motion should be completed in
 // (1 minute)/feed_rate time.
-void mc_line(float *target, float feed_rate, uint8_t invert_feed_rate);
+void mc_line(float *target, float feed_rate, uint8_t invert_feed_rate, uint32_t line_number);
 
 // Execute an arc in offset mode format. position == current xyz, target == target xyz, 
 // offset == offset from current xyz, axis_XXX defines circle plane in tool space, axis_linear is
 // the direction of helical travel, radius == circle radius, isclockwise boolean. Used
 // for vector transformation direction.
 void mc_arc(float *position, float *target, float *offset, uint8_t axis_0, uint8_t axis_1,
-  uint8_t axis_linear, float feed_rate, uint8_t invert_feed_rate, float radius, uint8_t isclockwise);
+  uint8_t axis_linear, float feed_rate, uint8_t invert_feed_rate, float radius, uint8_t isclockwise, uint32_t line_number);
   
 // Dwell for a specific number of seconds
 void mc_dwell(float seconds);

planner.c

@@ -272,7 +272,7 @@ void plan_synchronize()
    is used in three ways: as a normal feed rate if invert_feed_rate is false, as inverse time if
    invert_feed_rate is true, or as seek/rapids rate if the feed_rate value is negative (and
    invert_feed_rate always false). */
-void plan_buffer_line(float *target, float feed_rate, uint8_t invert_feed_rate) 
+void plan_buffer_line(float *target, float feed_rate, uint8_t invert_feed_rate, uint32_t line_number) 
 {
   // Prepare and initialize new block
   plan_block_t *block = &block_buffer[block_buffer_head];
@@ -280,6 +280,7 @@ void plan_buffer_line(float *target, float feed_rate, uint8_t invert_feed_rate)
   block->millimeters = 0;
   block->direction_bits = 0;
   block->acceleration = SOME_LARGE_VALUE; // Scaled down to maximum acceleration later
+  block->line_number = line_number;
 
   // Compute and store initial move distance data.
   // TODO: After this for-loop, we don't touch the stepper algorithm data. Might be a good idea

planner.h

@@ -26,7 +26,7 @@
 
 // The number of linear motions that can be in the plan at any give time
 #ifndef BLOCK_BUFFER_SIZE
-  #define BLOCK_BUFFER_SIZE 18
+  #define BLOCK_BUFFER_SIZE 16
 #endif
 
 // This struct stores a linear movement of a g-code block motion with its critical "nominal" values
@@ -47,6 +47,7 @@ typedef struct {
   float acceleration;            // Axis-limit adjusted line acceleration in (mm/min^2)
   float millimeters;             // The remaining distance for this block to be executed in (mm)
   // uint8_t max_override;       // Maximum override value based on axis speed limits
+  uint32_t line_number;
 } plan_block_t;
 
       
@@ -56,7 +57,7 @@ void plan_reset();
 // Add a new linear movement to the buffer. target[N_AXIS] is the signed, absolute target position 
 // in millimeters. Feed rate specifies the speed of the motion. If feed rate is inverted, the feed
 // rate is taken to mean "frequency" and would complete the operation in 1/feed_rate minutes.
-void plan_buffer_line(float *target, float feed_rate, uint8_t invert_feed_rate);
+void plan_buffer_line(float *target, float feed_rate, uint8_t invert_feed_rate, uint32_t line_number);
 
 // Called when the current block is no longer needed. Discards the block and makes the memory
 // availible for new blocks.

report.c

@@ -32,6 +32,7 @@
 #include "settings.h"
 #include "gcode.h"
 #include "coolant_control.h"
+#include "planner.h"
 
 
 // Handles the primary confirmation protocol response for streaming interfaces and human-feedback.
@@ -349,5 +350,16 @@ void report_realtime_status()
     if (i < (N_AXIS-1)) { printPgmString(PSTR(",")); }
   }
 
+  // Report current line number
+  printPgmString(PSTR(","));
+  printPgmString(PSTR("Ln:")); 
+  uint32_t ln=0;
+  plan_block_t * pb = plan_get_current_block();
+  if(pb != NULL) {
+    ln = pb->line_number;
+  } 
+  printInteger(ln);
+
+    
   printPgmString(PSTR(">\r\n"));
 }