ManuelW/grbl-LPC-CoreXY
1
0
Fork 0
Code Issues Pull Requests Releases 1 Wiki Activity

Moved homing origin to bottom/left instead of top/right

Browse Source
This commit is contained in:
cprezzi
2017-05-18 23:10:44 +02:00
parent d85bfa8c83
commit 50c13a1868
6 changed files with 47 additions and 84 deletions
Download Patch File Download Diff File Expand all files Collapse all files

37
grbl/config.h
View File

@ -129,6 +129,9 @@
// define to force Grbl to always set the machine origin at the homed location despite switch orientation.
// #define HOMING_FORCE_SET_ORIGIN // Uncomment to enable.
// Uncomment this define to force Grbl to always set the machine origin at bottom left.
#define HOMING_FORCE_POSITIVE_SPACE // Uncomment to enable.
// Number of blocks Grbl executes upon startup. These blocks are stored in EEPROM, where the size
// and addresses are defined in settings.h. With the current settings, up to 2 startup blocks may
// be stored and executed in order. These startup blocks would typically be used to set the g-code
@ -661,7 +664,7 @@
#define X_LIMIT_BIT 24 // X-MIN=24, X-MAX=25
#define Y_LIMIT_BIT 26 // Y-MIN=26, Y-MAX=27
#define Z_LIMIT_BIT 29 // Z-MIN=28, Z-MAX=29
#define LIMIT_MASK ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)) //|(1<<Z_LIMIT_BIT)) // All limit bits
#define LIMIT_MASK ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)) // All limit bits
// hard limits not ported #define LIMIT_INT PCIE0 // Pin change interrupt enable pin
// hard limits not ported #define LIMIT_INT_vect PCINT0_vect
// hard limits not ported #define LIMIT_PCMSK PCMSK0 // Pin change interrupt register
@ -712,10 +715,10 @@
#define CONTROL_INVERT_MASK CONTROL_MASK // May be re-defined to only invert certain control pins.
// Define probe switch input pin.
#define PROBE_DDR NotUsed
#define PROBE_PIN NotUsed
#define PROBE_PORT NotUsed
#define PROBE_BIT 5 // Uno Analog Pin 5
#define PROBE_DDR NotUsed // LPC_GPIO1->FIODIR
#define PROBE_PIN NotUsed // LPC_GPIO1->FIOPIN
#define PROBE_PORT NotUsed // LPC_GPIO1->FIOPIN
#define PROBE_BIT 5
#define PROBE_MASK (1<<PROBE_BIT)
// The LPC17xx has 6 PWM channels. Each channel has 2 pins. It can drive both pins simultaneously to the same value.
@ -729,9 +732,9 @@
// Stepper current control
//#define CURRENT_I2C Driver_I2C1 // I2C driver for current control. Comment out to disable.
#define CURRENT_MCP44XX_ADDR 0b0101100 // Address of MCP44XX
#define CURRENT_WIPERS {0, 1, 6, 7}; // Wiper registers (X, Y, Z, A)
#define CURRENT_FACTOR 113.33 // Convert amps to digipot value
//#define CURRENT_MCP44XX_ADDR 0b0101100 // Address of MCP44XX
//#define CURRENT_WIPERS {0, 1, 6, 7}; // Wiper registers (X, Y, Z, A)
//#define CURRENT_FACTOR 113.33 // Convert amps to digipot value
// Paste default settings definitions here.
#define DEFAULT_X_STEPS_PER_MM 160.0
@ -739,17 +742,17 @@
#define DEFAULT_Z_STEPS_PER_MM 160.0
#define DEFAULT_X_MAX_RATE 24000 // mm/min
#define DEFAULT_Y_MAX_RATE 24000 // mm/min
#define DEFAULT_Z_MAX_RATE 24000 // mm/min
#define DEFAULT_Z_MAX_RATE 500.0 // mm/min
#define DEFAULT_X_ACCELERATION (2500.0*60*60) // 5000*60*60 mm/min^2 = 5000 mm/sec^2
#define DEFAULT_Y_ACCELERATION (2500.0*60*60) // 5000*60*60 mm/min^2 = 5000 mm/sec^2
#define DEFAULT_Z_ACCELERATION (2500.0*60*60) // 5000*60*60 mm/min^2 = 5000 mm/sec^2
#define DEFAULT_X_CURRENT 0.0 // amps
#define DEFAULT_Y_CURRENT 0.0 // amps
#define DEFAULT_X_CURRENT 0.4 // amps
#define DEFAULT_Y_CURRENT 0.6 // amps
#define DEFAULT_Z_CURRENT 0.0 // amps
#define DEFAULT_A_CURRENT 0.0 // amps
#define DEFAULT_X_MAX_TRAVEL 300.0 // mm
#define DEFAULT_Y_MAX_TRAVEL 200.0 // mm
#define DEFAULT_Z_MAX_TRAVEL 200.0 // mm
#define DEFAULT_Z_MAX_TRAVEL 50.0 // mm
#define DEFAULT_SPINDLE_PWM_FREQ 5000 // Hz
#define DEFAULT_SPINDLE_PWM_OFF_VALUE 0.0 // Percent
#define DEFAULT_SPINDLE_PWM_MIN_VALUE 0.0 // Percent
@ -758,23 +761,23 @@
#define DEFAULT_SPINDLE_RPM_MIN 0.0 // rpm
#define DEFAULT_STEP_PULSE_MICROSECONDS 10
#define DEFAULT_STEPPING_INVERT_MASK 0
#define DEFAULT_DIRECTION_INVERT_MASK 0
#define DEFAULT_DIRECTION_INVERT_MASK 3
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 255 // msec (0-254, 255 keeps steppers enabled)
#define DEFAULT_STATUS_REPORT_MASK 0 // WPos enabled
#define DEFAULT_JUNCTION_DEVIATION 0.01 // mm
#define DEFAULT_ARC_TOLERANCE 0.002 // mm
#define DEFAULT_REPORT_INCHES 0 // false
#define DEFAULT_INVERT_ST_ENABLE 0 // false
#define DEFAULT_INVERT_LIMIT_PINS 3 // false
#define DEFAULT_INVERT_LIMIT_PINS 1 // false
#define DEFAULT_SOFT_LIMIT_ENABLE 1 // false
#define DEFAULT_HARD_LIMIT_ENABLE 0 // false
#define DEFAULT_INVERT_PROBE_PIN 0 // false
#define DEFAULT_LASER_MODE 1 // true
#define DEFAULT_HOMING_ENABLE 0 // false
#define DEFAULT_HOMING_DIR_MASK 0 // move positive dir
#define DEFAULT_HOMING_ENABLE 1 // false
#define DEFAULT_HOMING_DIR_MASK 1 // move positive dir
#define DEFAULT_HOMING_FEED_RATE 50.0 // mm/min
#define DEFAULT_HOMING_SEEK_RATE 6000.0 // mm/min
#define DEFAULT_HOMING_DEBOUNCE_DELAY 250 // msec (0-65k)
#define DEFAULT_HOMING_PULLOFF 1.0 // mm
#define DEFAULT_HOMING_PULLOFF 2.0 // mm
#endif