diff --git a/config.h b/config.h index 9aa5f51..86cf149 100644 --- a/config.h +++ b/config.h @@ -107,6 +107,8 @@ void store_setting(int parameter, double value); // Or bake your own like this adding any step-bits or directions you want to invert: // #define STEPPING_INVERT_MASK (STEP_MASK | (1<initial_rate = max(round(block->nominal_rate*entry_factor),MINIMAL_STEP_RATE); - int32_t final_rate = max(round(block->nominal_rate*entry_factor),MINIMAL_STEP_RATE); + block->initial_rate = round(block->nominal_rate*entry_factor); + int32_t final_rate = round(block->nominal_rate*entry_factor); int32_t acceleration_per_second = block->rate_delta*ACCELERATION_TICKS_PER_SECOND; int32_t acceleration_steps = estimate_acceleration_distance(block->initial_rate, block->nominal_rate, acceleration_per_second); @@ -67,3 +67,52 @@ void calculate_trapezoid_for_block(struct Block *block, double entry_factor, dou block->plateau_ticks = 0; } } + +// Add a new linear movement to the buffer. steps_x, _y and _z is the signed, relative motion in +// steps. Microseconds specify how many microseconds the move should take to perform. To aid acceleration +// calculation the caller must also provide the physical length of the line in millimeters. +void mp_buffer_line(int32_t steps_x, int32_t steps_y, int32_t steps_z, uint32_t microseconds, double millimeters) { + // Calculate the buffer head after we push this byte + int next_buffer_head = (block_buffer_head + 1) % BLOCK_BUFFER_SIZE; + // If the buffer is full: good! That means we are well ahead of the robot. + // Rest here until there is room in the buffer. + while(block_buffer_tail == next_buffer_head) { sleep_mode(); } + // Prepare to set up new block + struct Block *block = &block_buffer[block_buffer_head]; + // Number of steps for each axis + block->steps_x = labs(steps_x); + block->steps_y = labs(steps_y); + block->steps_z = labs(steps_z); + block->step_event_count = max(block->steps_x, max(block->steps_y, block->steps_z)); + // Bail if this is a zero-length block + if (block->step_event_count == 0) { return; }; + // Calculate speed in mm/minute for each axis + double multiplier = 60.0*1000000.0/microseconds; + block->speed_x = block->steps_x*multiplier/settings.steps_per_mm[0]; + block->speed_y = block->steps_y*multiplier/settings.steps_per_mm[1]; + block->speed_z = block->steps_z*multiplier/settings.steps_per_mm[2]; + block->nominal_rate = round(block->step_event_count*multiplier); + + // Compute the acceleration rate for the trapezoid generator. Depending on the slope of the line + // average travel per step event changes. For a line along one axis the travel per step event + // is equal to the travel/step in the particular axis. For a 45 degree line the steppers of both + // axes might step for every step event. Travel per step event is then sqrt(travel_x^2+travel_y^2). + // To generate trapezoids with contant acceleration between blocks the rate_delta must be computed + // specifically for each line to compensate for this phenomenon: + double travel_per_step = (1.0*millimeters)/block->step_event_count; + block->rate_delta = round( + (settings.acceleration/(60.0*ACCELERATION_TICKS_PER_SECOND))/ // acceleration mm/min per acceleration_tick + travel_per_step); // convert to: acceleration steps/min/acceleration_tick + calculate_trapezoid_for_block(block,0,0); // compute a default trapezoid + + // Compute direction bits for this block + block->direction_bits = 0; + if (steps_x < 0) { block->direction_bits |= (1<direction_bits |= (1<direction_bits |= (1<steps_x = labs(steps_x); - block->steps_y = labs(steps_y); - block->steps_z = labs(steps_z); - block->step_event_count = max(block->steps_x, max(block->steps_y, block->steps_z)); - // Bail if this is a zero-length block - if (block->step_event_count == 0) { return; }; - // Calculate speed in mm/minute for each axis - double multiplier = 60.0*1000000.0/microseconds; - block->speed_x = block->steps_x*multiplier/settings.steps_per_mm[0]; - block->speed_y = block->steps_y*multiplier/settings.steps_per_mm[1]; - block->speed_z = block->steps_z*multiplier/settings.steps_per_mm[2]; - block->nominal_rate = max(round(block->step_event_count*multiplier), MINIMAL_STEP_RATE); - - // Compute the acceleration rate for the trapezoid generator. Depending on the slope of the line - // average travel per step event changes. For a line along one axis the travel per step event - // is equal to the travel/step in the particular axis. For a 45 degree line the steppers of both - // axes might step for every step event. Travel per step event is then sqrt(travel_x^2+travel_y^2). - // To generate trapezoids with contant acceleration between blocks the rate_delta must be computed - // specifically for each line to compensate for this phenomenon: - double travel_per_step = (1.0*millimeters)/block->step_event_count; - block->rate_delta = round( - (settings.acceleration/(60.0*ACCELERATION_TICKS_PER_SECOND))/ // acceleration mm/min per acceleration_tick - travel_per_step); // convert to: acceleration steps/min/acceleration_tick - calculate_trapezoid_for_block(block,0,0); // compute a default trapezoid - - // Compute direction bits for this block - block->direction_bits = 0; - if (steps_x < 0) { block->direction_bits |= (1<direction_bits |= (1<direction_bits |= (1< #include -#define ACCELERATION_TICKS_PER_SECOND 10 -#define MINIMAL_STEP_RATE (ACCELERATION_TICKS_PER_SECOND*5) - // Initialize and start the stepper motor subsystem void st_init();