grbl-LPC-CoreXY/gcode.c

/*
  gcode.c - rs274/ngc parser.
  Part of Grbl

  Copyright (c) 2011-2014 Sungeun K. Jeon
  Copyright (c) 2009-2011 Simen Svale Skogsrud
  
  Grbl is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  Grbl is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with Grbl.  If not, see <http://www.gnu.org/licenses/>.
*/

#include "system.h"
#include "settings.h"
#include "protocol.h"
#include "gcode.h"
#include "motion_control.h"
#include "spindle_control.h"
#include "coolant_control.h"
#include "probe.h"
#include "report.h"

#define MAX_LINE_NUMBER 99999

#define AXIS_COMMAND_NONE 0
#define AXIS_COMMAND_NON_MODAL 1 
#define AXIS_COMMAND_MOTION_MODE 2

// Declare gc extern struct
parser_state_t gc_state;
parser_block_t gc_block;

#define FAIL(status) return(status);


void gc_init() 
{
  memset(&gc_state, 0, sizeof(gc_state));
  
  // Load default G54 coordinate system.
  if (!(settings_read_coord_data(gc_state.modal.coord_select,gc_state.coord_system))) { 
    report_status_message(STATUS_SETTING_READ_FAIL); 
  } 
}


// Sets g-code parser position in mm. Input in steps. Called by the system abort and hard
// limit pull-off routines.
void gc_sync_position() 
{
  uint8_t i;
  for (i=0; i<N_AXIS; i++) {
    gc_state.position[i] = sys.position[i]/settings.steps_per_mm[i];
  }
}


static uint8_t gc_check_same_position(float *pos_a, float *pos_b) 
{
  uint8_t idx;
  for (idx=0; idx<N_AXIS; idx++) {
    if (pos_a[idx] != pos_b[idx]) { return(false); }
  }
  return(true);
}
         
// Executes one line of 0-terminated G-Code. The line is assumed to contain only uppercase
// characters and signed floating point values (no whitespace). Comments and block delete
// characters have been removed. In this function, all units and positions are converted and 
// exported to grbl's internal functions in terms of (mm, mm/min) and absolute machine 
// coordinates, respectively.
uint8_t gc_execute_line(char *line) 
{
  /* -------------------------------------------------------------------------------------
     STEP 1: Initialize parser block struct and copy current g-code state modes. The parser
     updates these modes and commands as the block line is parser and will only be used and
     executed after successful error-checking. The parser block struct also contains a block
     values struct, word tracking variables, and a non-modal commands tracker for the new 
     block. This struct contains all of the necessary information to execute the block. */
     
  memset(&gc_block, 0, sizeof(gc_block)); // Initialize the parser block struct.
  memcpy(&gc_block.modal,&gc_state.modal,sizeof(gc_modal_t)); // Copy current modes
  uint8_t axis_explicit = AXIS_COMMAND_NONE;
  uint8_t axis_0, axis_1, axis_linear;
  float coordinate_data[N_AXIS];
  float parameter_data[N_AXIS];
  
  // Initialize bitflag tracking variables for axis indices compatible operations.
  uint8_t axis_words = 0; // XYZ tracking
  uint8_t ijk_words = 0; // IJK tracking 

  // Initialize command and value words variables. Tracks words contained in this block.
  uint16_t command_words = 0; // G and M command words. Also used for modal group violations.
  uint16_t value_words = 0; // Value words. 

  /* -------------------------------------------------------------------------------------
     STEP 2: Import all g-code words in the block line. A g-code word is a letter followed by
     a number, which can either be a 'G'/'M' command or sets/assigns a command value. Also, 
     perform initial error-checks for command word modal group violations, for any repeated
     words, and for negative values set for the value words F, N, P, T, and S. */
     
  uint8_t word_bit; // Bit-value for assigning tracking variables
  uint8_t char_counter = 0;  
  char letter;
  float value;
  uint8_t int_value = 0;
  uint8_t mantissa = 0; // NOTE: For mantissa values > 255, variable type must be changed to uint16_t.

  while (line[char_counter] != 0) { // Loop until no more g-code words in line.
    
    // Import the next g-code word, expecting a letter followed by a value. Otherwise, error out.
    letter = line[char_counter];
    if((letter < 'A') || (letter > 'Z')) { FAIL(STATUS_EXPECTED_COMMAND_LETTER); } // [Expected word letter]
    char_counter++;
    if (!read_float(line, &char_counter, &value)) { FAIL(STATUS_BAD_NUMBER_FORMAT); } // [Expected word value]

    // Convert values to smaller uint8 significand and mantissa values for parsing this word.
    // NOTE: Mantissa is multiplied by 100 to catch non-integer command values. This is more 
    // accurate than the NIST gcode requirement of x10 when used for commands, but not quite
    // accurate enough for value words that require integers to within 0.0001. This should be
    // a good enough comprimise and catch most all non-integer errors. To make it compliant, 
    // we would simply need to change the mantissa to int16, but this add compiled flash space.
    // Maybe update this later. 
    int_value = trunc(value);
    mantissa = trunc(100*(value - int_value)); // Compute mantissa for Gxx.x commands

    // Check if the g-code word is supported or errors due to modal group violations or has
    // been repeated in the g-code block. If ok, update the command or record its value.
    switch(letter) {
    
      /* 'G' and 'M' Command Words: Parse commands and check for modal group violations.
         NOTE: Modal group numbers are defined in Table 4 of NIST RS274-NGC v3, pg.20 */
         
      case 'G':
        // Determine 'G' command and its modal group
        switch(int_value) {
          case 10: case 28: case 30: case 92: 
            // Check for G10/28/30/92 being called with G0/1/2/3/38 on same block.
            if (mantissa == 0) { // Ignore G28.1, G30.1, and G92.1
              if (axis_explicit) { FAIL(STATUS_GCODE_AXIS_COMMAND_CONFLICT); } // [Axis word/command conflict]
              axis_explicit = AXIS_COMMAND_NON_MODAL;
            }
            // No break. Continues to next line.
          case 4: case 53: 
            word_bit = MODAL_GROUP_G0; 
            switch(int_value) {
              case 4: gc_block.non_modal_command = NON_MODAL_DWELL; break; // G4
              case 10: gc_block.non_modal_command = NON_MODAL_SET_COORDINATE_DATA; break; // G10
              case 28:
                switch(mantissa) {
                  case 0: gc_block.non_modal_command = NON_MODAL_GO_HOME_0; break;  // G28
                  case 10: gc_block.non_modal_command = NON_MODAL_SET_HOME_0; break; // G28.1
                  default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); // [Unsupported G28.x command]
                }
                mantissa = 0; // Set to zero to indicate valid non-integer G command.
                break;
              case 30: 
                switch(mantissa) {
                  case 0: gc_block.non_modal_command = NON_MODAL_GO_HOME_1; break;  // G30
                  case 10: gc_block.non_modal_command = NON_MODAL_SET_HOME_1; break; // G30.1
                  default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); // [Unsupported G30.x command]
                }
                mantissa = 0; // Set to zero to indicate valid non-integer G command.
                break;
              case 53: gc_block.non_modal_command = NON_MODAL_ABSOLUTE_OVERRIDE; break; // G53
              case 92: 
                switch(mantissa) {
                  case 0: gc_block.non_modal_command = NON_MODAL_SET_COORDINATE_OFFSET; break; // G92
                  case 10: gc_block.non_modal_command = NON_MODAL_RESET_COORDINATE_OFFSET; break; // G92.1
                  default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); // [Unsupported G92.x command]
                }
                mantissa = 0; // Set to zero to indicate valid non-integer G command.
                break;      
            }
            break;
          case 0: case 1: case 2: case 3: case 38: 
            // Check for G0/1/2/3/38 being called with G10/28/30/92 on same block.
            if (axis_explicit) { FAIL(STATUS_GCODE_AXIS_COMMAND_CONFLICT); } // [Axis word/command conflict]
            axis_explicit = AXIS_COMMAND_MOTION_MODE; 
            // No break. Continues to next line.
          case 80: 
            word_bit = MODAL_GROUP_G1; 
            switch(int_value) {
              case 0: gc_block.modal.motion = MOTION_MODE_SEEK; break; // G0
              case 1: gc_block.modal.motion = MOTION_MODE_LINEAR; break; // G1
              case 2: gc_block.modal.motion = MOTION_MODE_CW_ARC; break; // G2
              case 3: gc_block.modal.motion = MOTION_MODE_CCW_ARC; break; // G3
              case 38: 
                switch(mantissa) {
                  case 20: gc_block.modal.motion = MOTION_MODE_PROBE; break;  // G38.2
                  // NOTE: If G38.3+ are enabled, change mantissa variable type to uint16_t.
                  // case 30: gc_block.modal.motion = MOTION_MODE_PROBE_NO_ERROR; break; // G38.3 Not supported.
                  // case 40: // Not supported.
                  // case 50: // Not supported.
                  default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); // [Unsupported G38.x command]
                }
                mantissa = 0; // Set to zero to indicate valid non-integer G command.
                break;
              case 80: gc_block.modal.motion = MOTION_MODE_NONE; break; // G80
            }            
            break;
          case 17: case 18: case 19: 
            word_bit = MODAL_GROUP_G2; 
            switch(int_value) {
              case 17: gc_block.modal.plane_select = PLANE_SELECT_XY; break;
              case 18: gc_block.modal.plane_select = PLANE_SELECT_ZX; break;
              case 19: gc_block.modal.plane_select = PLANE_SELECT_YZ; break;
            }
            break;
          case 90: case 91: 
            word_bit = MODAL_GROUP_G3; 
            if (int_value == 90) { gc_block.modal.distance = DISTANCE_MODE_ABSOLUTE; } // G90
            else { gc_block.modal.distance = DISTANCE_MODE_INCREMENTAL; } // G91            
            break;
          case 93: case 94: 
            word_bit = MODAL_GROUP_G5; 
            if (int_value == 93) { gc_block.modal.feed_rate = FEED_RATE_MODE_INVERSE_TIME; } // G93
            else { gc_block.modal.feed_rate = FEED_RATE_MODE_UNITS_PER_MIN; } // G94
            break;
          case 20: case 21: 
            word_bit = MODAL_GROUP_G6; 
            if (int_value == 20) { gc_block.modal.units = UNITS_MODE_INCHES; }  // G20
            else { gc_block.modal.units = UNITS_MODE_MM; } // G21
            break;
          case 54: case 55: case 56: case 57: case 58: case 59: 
            // NOTE: G59.x are not supported. (But their int_values would be 60, 61, and 62.)
            word_bit = MODAL_GROUP_G12;
            gc_block.modal.coord_select = int_value-54; // Shift to array indexing.
            break;
          default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); // [Unsupported G command]
        }      
        if (mantissa > 0) { FAIL(STATUS_GCODE_COMMAND_VALUE_NOT_INTEGER); } // [Unsupported or invalid Gxx.x command]
        // Check for more than one command per modal group violations in the current block
        // NOTE: Variable 'word_bit' is always assigned, if the command is valid.
        if ( bit_istrue(command_words,bit(word_bit)) ) { FAIL(STATUS_GCODE_MODAL_GROUP_VIOLATION); }
        bit_true(command_words,bit(word_bit));
        break;
        
      case 'M':
      
        // Determine 'M' command and its modal group
        if (mantissa > 0) { FAIL(STATUS_GCODE_COMMAND_VALUE_NOT_INTEGER); } // [No Mxx.x commands]
        switch(int_value) {
          case 0: case 1: case 2: case 30: 
            word_bit = MODAL_GROUP_M4; 
            switch(int_value) {
              case 0: gc_block.modal.program_flow = PROGRAM_FLOW_PAUSED; break; // Program pause
              case 1: break; // Optional stop not supported. Ignore.
              case 2: case 30: gc_block.modal.program_flow = PROGRAM_FLOW_COMPLETED; break; // Program end and reset 
            }
            break;
          case 3: case 4: case 5: 
            word_bit = MODAL_GROUP_M7; 
            switch(int_value) {
              case 3: gc_block.modal.spindle = SPINDLE_ENABLE_CW; break;
              case 4: gc_block.modal.spindle = SPINDLE_ENABLE_CCW; break;
              case 5: gc_block.modal.spindle = SPINDLE_DISABLE; break;
            }
            break;            
         #ifdef ENABLE_M7  
          case 7:
         #endif
          case 8: case 9:
            word_bit = MODAL_GROUP_M8; 
            switch(int_value) {      
             #ifdef ENABLE_M7
              case 7: gc_block.modal.coolant = COOLANT_MIST_ENABLE; break;
             #endif
              case 8: gc_block.modal.coolant = COOLANT_FLOOD_ENABLE; break;
              case 9: gc_block.modal.coolant = COOLANT_DISABLE; break;
            }
            break;
          default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); // [Unsupported M command]
        }            
      
        // Check for more than one command per modal group violations in the current block
        // NOTE: Variable 'word_bit' is always assigned, if the command is valid.
        if ( bit_istrue(command_words,bit(word_bit)) ) { FAIL(STATUS_GCODE_MODAL_GROUP_VIOLATION); }
        bit_true(command_words,bit(word_bit));
        break;
      
      // NOTE: All remaining letters assign values.
      default: 
  
        /* Non-Command Words: This initial parsing phase only checks for repeats of the remaining
           legal g-code words and stores their value. Error-checking is performed later since some
           words (I,J,K,L,P,R) have multiple connotations and/or depend on the issued commands. */
        switch(letter){
          // case 'A': // Not supported
          // case 'B': // Not supported
          // case 'C': // Not supported
          // case 'D': // Not supported
          case 'F': word_bit = WORD_F; gc_block.values.f = value; break;
          // case 'H': // Not supported
          case 'I': word_bit = WORD_I; gc_block.values.ijk[X_AXIS] = value; ijk_words |= (1<<X_AXIS); break;
          case 'J': word_bit = WORD_J; gc_block.values.ijk[Y_AXIS] = value; ijk_words |= (1<<Y_AXIS); break;
          case 'K': word_bit = WORD_K; gc_block.values.ijk[Z_AXIS] = value; ijk_words |= (1<<Z_AXIS); break;
          case 'L': word_bit = WORD_L; gc_block.values.l = int_value; break;
          case 'N': word_bit = WORD_N; gc_block.values.n = int_value; break;
          case 'P': word_bit = WORD_P; gc_block.values.p = value; break;
          // NOTE: For certain commands, P value must be an integer, but none of these commands are supported.
          // case 'Q': // Not supported
          case 'R': word_bit = WORD_R; gc_block.values.r = value; break;
          case 'S': word_bit = WORD_S; gc_block.values.s = value; break;
          case 'T': word_bit = WORD_T; break; // gc.values.t = int_value;
          case 'X': word_bit = WORD_X; gc_block.values.xyz[X_AXIS] = value; axis_words |= (1<<X_AXIS); break;
          case 'Y': word_bit = WORD_Y; gc_block.values.xyz[Y_AXIS] = value; axis_words |= (1<<Y_AXIS); break;
          case 'Z': word_bit = WORD_Z; gc_block.values.xyz[Z_AXIS] = value; axis_words |= (1<<Z_AXIS); break;
          default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND);
        } 
        
        // NOTE: Variable 'word_bit' is always assigned, if the non-command letter is valid.
        if (bit_istrue(value_words,bit(word_bit))) { FAIL(STATUS_GCODE_WORD_REPEATED); } // [Word repeated]
        // Check for invalid negative values for words F, N, P, T, and S.
        // NOTE: Negative value check is done here simply for code-efficiency.
        if ( bit(word_bit) & (bit(WORD_F)|bit(WORD_N)|bit(WORD_P)|bit(WORD_T)|bit(WORD_S)) ) {
          if (value < 0.0) { FAIL(STATUS_NEGATIVE_VALUE); } // [Word value cannot be negative]
        }
        value_words |= bit(word_bit); // Flag to indicate parameter assigned.
      
    }   
  } 
  // Parsing complete!
  

  /* -------------------------------------------------------------------------------------
     STEP 3: Error-check all commands and values passed in this block. This step ensures all of
     the commands are valid for execution and follows the NIST standard as closely as possible.
     If an error is found, all commands and values in this block are dumped and will not update
     the active system g-code modes. If the block is ok, the active system g-code modes will be
     updated based on the commands of this block, and signal for it to be executed. 
     
     Also, we have to pre-convert all of the values passed based on the modes set by the parsed
     block. There are a number of error-checks that require target information that can only be
     accurately calculated if we convert these values in conjunction with the error-checking.
     This relegates the next execution step as only updating the system g-code modes and 
     performing the programmed actions in order. The execution step should not require any 
     conversion calculations and would only require minimal checks necessary to execute.
  */

  /* NOTE: At this point, the g-code block has been parsed and the block line can be freed.
     NOTE: It's also possible, at some future point, to break up STEP 2, to allow piece-wise 
     parsing of the block on a per-word basis, rather than the entire block. This could remove 
     the need for maintaining a large string variable for the entire block and free up some memory. 
     To do this, this would simply need to retain all of the data in STEP 1, such as the new block
     data struct, the modal group and value bitflag tracking variables, and axis array indices 
     compatible variables. This data contains all of the information necessary to error-check the 
     new g-code block when the EOL character is received. However, this would break Grbl's startup
     lines in how it currently works and would require some refactoring to make it compatible.
  */  
  
  // [0. Non-specific/common error-checks and miscellaneous setup]: 
  
  // Determine how axis words are used and error-check it. Apply implicit conditions and exceptions.
  if (axis_explicit) { // Either a non-modal or motion mode axis-explicit command has been passed.
    // Axis-words are required (with exceptions) with axis-explicit commands.
    // NOTE: G28/30 reserve any axis words as an intermediate motion, but are not required. G2/3 full
    // circle arcs don't require axis words, but this aren't supported.
    if (!axis_words) {
      if ((gc_block.non_modal_command == NON_MODAL_GO_HOME_0) || (gc_block.non_modal_command == NON_MODAL_GO_HOME_1)) {
        axis_explicit = AXIS_COMMAND_NONE; // No axis words passed for G28/30.
      } else { 
        FAIL(STATUS_GCODE_NO_AXIS_WORDS); // [No axis words]
      }
    }
  } else {
    // If no axis-explicit commands in the block, axis words implicitly activate the current motion mode.
    if (axis_words) { axis_explicit = AXIS_COMMAND_MOTION_MODE; } // Assign implicit motion-mode
  }
  
  // Check for valid line number N value.
  if (bit_istrue(value_words,bit(WORD_N))) {
    // Line number value cannot be less than zero (done) or greater than max line number.
    if (gc_block.values.n > MAX_LINE_NUMBER) { FAIL(STATUS_GCODE_INVALID_LINE_NUMBER); } // [Exceeds max line number]
  }
  // bit_false(value_words,bit(WORD_N)); // NOTE: Single-meaning value word. Set at end of error-checking.
  
  // Track for unused words at the end of error-checking.
  // NOTE: Single-meaning value words are removed all at once at the end of error-checking, because
  // they are always used when present. This was done to save a few bytes of flash. For clarity, the
  // single-meaning value words may be removed as they are used. Also, axis words are treated in the
  // same way. If there is an axis explicit/implicit command, XYZ words are always used and are 
  // are removed at the end of error-checking.  
  
  // [1. Comments ]: MSG's NOT SUPPORTED. Comment handling performed by protocol.
  
  // [2. Set feed rate mode ]: G93 F word missing with G1,G2/3 active, implicitly or explicitly. Feed rate
  //   is not defined after switching to G94 from G93.
  if (gc_block.modal.feed_rate == FEED_RATE_MODE_INVERSE_TIME) { // = G93
    // NOTE: G38 can also operate in inverse time, but is undefined as an error. Missing F word check added here.
    if (axis_explicit == AXIS_COMMAND_MOTION_MODE) { 
      if ((gc_block.modal.motion != MOTION_MODE_NONE) || (gc_block.modal.motion != MOTION_MODE_SEEK)) {
        if (bit_isfalse(value_words,bit(WORD_F))) { FAIL(STATUS_GCODE_UNDEFINED_FEED_RATE); } // [F word missing]
      }
    }
    // NOTE: It seems redundant to check for an F word to be passed after switching from G94 to G93. We would
    // accomplish the exact same thing if the feed rate value is always reset to zero and undefined after each
    // inverse time block, since the commands that use this value already perform undefined checks. This would
    // also allow other commands, following this switch, to execute and not error out needlessly. This code is 
    // combined with the above feed rate mode and the below set feed rate error-checking.

    // [3. Set feed rate ]: F is negative (done.)
    // - In inverse time mode: Always implicitly zero the feed rate value before and after block completion.
    // NOTE: If in G93 mode or switched into it from G94, just keep F value as initialized zero or passed F word 
    // value in the block. If no F word is passed with a motion command that requires a feed rate, this will error 
    // out in the motion modes error-checking. However, if no F word is passed with NO motion command that requires
    // a feed rate, we simply move on and the state feed rate value gets updated to zero and remains undefined.
  } else { // = G94
    // - In units per mm mode: If F word passed, ensure value is in mm/min, otherwise push last state value.
    if (gc_state.modal.feed_rate == FEED_RATE_MODE_UNITS_PER_MIN) { // Last state is also G94
      if (bit_istrue(value_words,bit(WORD_F))) {
        if (gc_block.modal.units == UNITS_MODE_INCHES) { gc_block.values.f *= MM_PER_INCH; }
      } else {
        gc_block.values.f = gc_state.feed_rate; // Push last state feed rate
      }
    } // Else, switching to G94 from G93, so don't push last state feed rate. Its undefined or the passed F word value.
  } 
  // bit_false(value_words,bit(WORD_F)); // NOTE: Single-meaning value word. Set at end of error-checking.
  
  // [4. Set spindle speed ]: S is negative (done.)
  if (bit_isfalse(value_words,bit(WORD_S))) { gc_block.values.s = gc_state.spindle_speed; }
  // bit_false(value_words,bit(WORD_S)); // NOTE: Single-meaning value word. Set at end of error-checking.
    
  // [5. Select tool ]: NOT SUPPORTED. T is negative (done.) Not an integer. Greater than max tool value.
  // bit_false(value_words,bit(WORD_T)); // NOTE: Single-meaning value word. Set at end of error-checking.

  // [6. Change tool ]: N/A
  // [7. Spindle control ]: N/A
  // [8. Coolant control ]: N/A
  // [9. Enable/disable feed rate or spindle overrides ]: NOT SUPPORTED.
  
  // [10. Dwell ]: P value missing. P is negative (done.) NOTE: See below.
  if (gc_block.non_modal_command == NON_MODAL_DWELL) {
    if (bit_isfalse(value_words,bit(WORD_P))) { FAIL(STATUS_GCODE_VALUE_WORD_MISSING); } // [P word missing]
    bit_false(value_words,bit(WORD_P));
  }
  
  // [11. Set active plane ]: N/A
  switch (gc_block.modal.plane_select) {
    case PLANE_SELECT_XY:
      axis_0 = X_AXIS;
      axis_1 = Y_AXIS;
      axis_linear = Z_AXIS;
      break;
    case PLANE_SELECT_ZX:
      axis_0 = Z_AXIS;
      axis_1 = X_AXIS;
      axis_linear = Y_AXIS;
      break;
    default: // case PLANE_SELECT_YZ:
      axis_0 = Y_AXIS;
      axis_1 = Z_AXIS;
      axis_linear = X_AXIS;
  }   
            
  // [12. Set length units ]: N/A
  // Pre-convert XYZ coordinate values to millimeters, if applicable.
  uint8_t idx;
  if (gc_block.modal.units == UNITS_MODE_INCHES) {
    for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used.
      if (bit_istrue(axis_words,bit(idx)) ) {
        gc_block.values.xyz[idx] *= MM_PER_INCH;
      }
    }
  }
  
  // [13. Cutter radius compensation ]: NOT SUPPORTED. Error, if G53 is active.
  // [14. Cutter length compensation ]: NOT SUPPORTED.
  
  // [15. Coordinate system selection ]: *N/A. Error, if cutter radius comp is active.
  // TODO: An EEPROM read of the coordinate data may require a buffer sync when the cycle
  // is active. The read pauses the processor temporarily and may cause a rare crash. For 
  // future versions on processors with enough memory, all coordinate data should be stored
  // in memory and written to EEPROM only when there is not a cycle active.
  memcpy(coordinate_data,gc_state.coord_system,sizeof(gc_state.coord_system));
  if ( bit_istrue(command_words,bit(MODAL_GROUP_G12)) ) { // Check if called in block
    if (gc_block.modal.coord_select > N_COORDINATE_SYSTEM) { FAIL(STATUS_GCODE_UNSUPPORTED_COORD_SYS); } // [Greater than N sys]
    if (gc_state.modal.coord_select != gc_block.modal.coord_select) {
      if (!(settings_read_coord_data(gc_block.modal.coord_select,coordinate_data))) { FAIL(STATUS_SETTING_READ_FAIL); } 
    }
  }
  
  // [16. Set path control mode ]: NOT SUPPORTED.
  // [17. Set distance mode ]: N/A. G90.1 and G91.1 NOT SUPPORTED.
  // [18. Set retract mode ]: NOT SUPPORTED.
  
  // [19. Remaining non-modal actions ]: Check go to predefined position, set G10, or set axis offsets.
  // NOTE: We need to separate the non-modal commands that are axis-explicit (G10/G28/G30/G92), as these
  // commands all treat axis words differently. G10 as absolute offsets or computes current position as
  // the axis value, G92 similarly to G10 L20, and G28/30 as an intermediate target position that observes
  // all the current coordinate system and G92 offsets. 
  switch (gc_block.non_modal_command) {
    case NON_MODAL_SET_COORDINATE_DATA:  
      // [G10 Errors]: L missing and is not 2 or 20. P word missing. (Negative P value done.)
      // [G10 L2 Errors]: R word NOT SUPPORTED. P value not 0 to nCoordSys(max 9). Axis words missing (done.)
      // [G10 L20 Errors]: P must be 0 to nCoordSys(max 9). Axis words missing (done.)
      if (bit_isfalse(value_words,((1<<WORD_P)|(1<<WORD_L)))) { FAIL(STATUS_GCODE_VALUE_WORD_MISSING); } // [P/L word missing]
      int_value = trunc(gc_block.values.p); // Convert p value to int.
      if (int_value > N_COORDINATE_SYSTEM) { FAIL(STATUS_GCODE_UNSUPPORTED_COORD_SYS); } // [Greater than N sys]
      if (gc_block.values.l != 20) {
        if (gc_block.values.l == 2) {
          if (bit_istrue(value_words,bit(WORD_R))) { FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); } // [G10 L2 R not supported]
        } else { FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); } // [Unsupported L]
      }
      bit_false(value_words,(bit(WORD_L)|bit(WORD_P)));
    
      // Load EEPROM coordinate data and pre-calculate the new coordinate data.
      if (int_value > 0) { int_value--; } // Adjust P1-P6 index to EEPROM coordinate data indexing.
      else { int_value = gc_block.modal.coord_select; } // Index P0 as the active coordinate system
      if (!settings_read_coord_data(int_value,parameter_data)) { FAIL(STATUS_SETTING_READ_FAIL); } // [EEPROM read fail]
      for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used.
        // Update axes defined only in block. Always in machine coordinates. Can change non-active system.
        if (bit_istrue(axis_words,bit(idx)) ) {
          if (gc_block.values.l == 20) {
            // NOTE: Undefined if G92 offsets apply to this calculation. Omitted.
            parameter_data[idx] = gc_state.position[idx]-gc_block.values.xyz[idx]; // L20: Update axis current position to target
          } else {
            parameter_data[idx] = gc_block.values.xyz[idx]; // L2: Update coordinate system axis
          }
        }
      }
      break;
    case NON_MODAL_SET_COORDINATE_OFFSET:
      // [G92 Errors]: No axis words (done.)
    
      // Update axes defined only in block. Offsets current system to defined value. Does not update when
      // active coordinate system is selected, but is still active unless G92.1 disables it. 
      for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used.
        if (bit_istrue(axis_words,bit(idx)) ) {
          gc_block.values.xyz[idx] = gc_state.position[idx]-coordinate_data[idx]-gc_block.values.xyz[idx];
        } else {
          gc_block.values.xyz[idx] = gc_state.coord_offset[idx];
        }
      }
      break;
      
    default:
    
      // At this point, the rest of the axis-explicit commands treat the axis values as the traditional
      // target position with the coordinate system offsets, G92 offsets, absolute override, and distance
      // modes applied. This includes the motion mode commands. We can now pre-compute the target position.
      // NOTE: Tool offsets may be appended to these conversions when/if this feature is added.
      if (axis_words) {
        for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used to save flash space.
          if ( bit_isfalse(axis_words,bit(idx)) ) {
            gc_block.values.xyz[idx] = gc_state.position[idx]; // No axis word in block. Keep same axis position.
          } else {
            // Update specified value according to distance mode or ignore if absolute override is active.
            // NOTE: G53 is never active with G28/30 since they are in the same modal group.
            if (gc_block.non_modal_command != NON_MODAL_ABSOLUTE_OVERRIDE) {
              // Apply coordinate offsets based on distance mode.
              if (gc_block.modal.distance == DISTANCE_MODE_ABSOLUTE) {
                gc_block.values.xyz[idx] += coordinate_data[idx] + gc_state.coord_offset[idx];
              } else {  // Incremental mode
                gc_block.values.xyz[idx] += gc_state.position[idx];
              }
            }
          }
        }
      }
    
      // Check remaining non-modal commands for errors.
      switch (gc_block.non_modal_command) {        
        case NON_MODAL_GO_HOME_0: 
          // [G28 Errors]: Cutter compensation is enabled. 
          // Retreive G28 go-home position data (in machine coordinates) from EEPROM
          if (!settings_read_coord_data(SETTING_INDEX_G28,parameter_data)) { FAIL(STATUS_SETTING_READ_FAIL); }
          break;
        case NON_MODAL_GO_HOME_1:
          // [G30 Errors]: Cutter compensation is enabled. 
          // Retreive G30 go-home position data (in machine coordinates) from EEPROM
          if (!settings_read_coord_data(SETTING_INDEX_G30,parameter_data)) { FAIL(STATUS_SETTING_READ_FAIL); }
          break;
        case NON_MODAL_SET_HOME_0: case NON_MODAL_SET_HOME_1:
          // [G28.1/30.1 Errors]: Cutter compensation is enabled. 
          // NOTE: If axis words are passed here, they are interpreted as an implicit motion mode.
          break;
        case NON_MODAL_RESET_COORDINATE_OFFSET: 
          // NOTE: If axis words are passed here, they are interpreted as an implicit motion mode.
          break;
        case NON_MODAL_ABSOLUTE_OVERRIDE:
          // [G53 Errors]: G0 and G1 are not active. Cutter compensation is enabled.
          // NOTE: All explicit axis word commands are in this modal group. So no implicit check necessary.
          if (!(gc_block.modal.motion == MOTION_MODE_SEEK || gc_block.modal.motion == MOTION_MODE_LINEAR)) {
            FAIL(STATUS_GCODE_G53_INVALID_MOTION_MODE); // [G53 G0/1 not active]
          }
          break;
      }
  }
      
  // [20. Motion modes ]: 
  if (gc_block.modal.motion == MOTION_MODE_NONE) {
    // [G80 Errors]: Axis word exist and are not used by a non-modal command.
    if ((axis_words) && (axis_explicit != AXIS_COMMAND_NON_MODAL)) { 
      FAIL(STATUS_GCODE_AXIS_WORDS_EXIST); // [No axis words allowed]
    }

  // Check remaining motion modes, if axis word are implicit (exist and not used by G10/28/30/92), or 
  // was explicitly commanded in the g-code block.
  } else if ( axis_explicit == AXIS_COMMAND_MOTION_MODE ) {
  
    // [G0 Errors]: (All done!) No axis words. Axis letter not configured or without real value.

    // All remaining motion modes (all but G0 and G80), require a valid feed rate value. In units per mm mode,
    // the value must be positive. In inverse time mode, a positive value must be passed with each block.
    if (gc_block.modal.motion != MOTION_MODE_SEEK) {
      
      // Check if feed rate is defined for the motion modes that require it.
      if (gc_block.values.f == 0.0) { FAIL(STATUS_GCODE_UNDEFINED_FEED_RATE); } // [Feed rate undefined]
     
      switch (gc_block.modal.motion) {
        case MOTION_MODE_LINEAR: 
          // [G1 Errors]: (All done!) No axis words and feed rate undefined. Axis letter not configured or without real value.
          break;
        case MOTION_MODE_CW_ARC: case MOTION_MODE_CCW_ARC:
          // [G2/3 Errors All-Modes]: Feed rate undefined.
          // [G2/3 Radius-Mode Errors]: No axis words in selected plane. Target point is same as current.
          // [G2/3 Offset-Mode Errors]: No axis words and/or offsets in selected plane. The radius to the current 
          //   point and the radius to the target point differs more than 0.002mm (EMC def. 0.5mm OR 0.005mm and 0.1% radius).   
          // [G2/3 Full-Circle-Mode Errors]: NOT SUPPORTED. Axis words exist. No offsets programmed. P must be an integer.        
          // NOTE: Both radius and offsets are required for arc tracing and are pre-computed with the error-checking.
        
          if (!(axis_words & (bit(axis_0)|bit(axis_1)))) { FAIL(STATUS_GCODE_NO_AXIS_WORDS_IN_PLANE); } // [No axis words in plane]
        
          // Calculate the change in position along each selected axis
          float x = gc_block.values.xyz[axis_0]-gc_state.position[axis_0]; // Delta x between current position and target
          float y = gc_block.values.xyz[axis_1]-gc_state.position[axis_1]; // Delta y between current position and target
                
          if (value_words & bit(WORD_R)) { // Arc Radius Mode  
            bit_false(value_words,bit(WORD_R));
            if (gc_check_same_position(gc_state.position, gc_block.values.xyz)) { FAIL(STATUS_GCODE_INVALID_TARGET); } // [Invalid target]
          
            // Convert radius value to proper units.
            if (gc_block.modal.units == UNITS_MODE_INCHES) { gc_block.values.r *= MM_PER_INCH; }
            /*  We need to calculate the center of the circle that has the designated radius and passes
                through both the current position and the target position. This method calculates the following
                set of equations where [x,y] is the vector from current to target position, d == magnitude of 
                that vector, h == hypotenuse of the triangle formed by the radius of the circle, the distance to
                the center of the travel vector. A vector perpendicular to the travel vector [-y,x] is scaled to the 
                length of h [-y/d*h, x/d*h] and added to the center of the travel vector [x/2,y/2] to form the new point 
                [i,j] at [x/2-y/d*h, y/2+x/d*h] which will be the center of our arc.
    
                d^2 == x^2 + y^2
                h^2 == r^2 - (d/2)^2
                i == x/2 - y/d*h
                j == y/2 + x/d*h
    
                                                                     O <- [i,j]
                                                                  -  |
                                                        r      -     |
                                                            -        |
                                                         -           | h
                                                      -              |
                                        [0,0] ->  C -----------------+--------------- T  <- [x,y]
                                                  | <------ d/2 ---->|
              
                C - Current position
                T - Target position
                O - center of circle that pass through both C and T
                d - distance from C to T
                r - designated radius
                h - distance from center of CT to O
    
                Expanding the equations:
 
                d -> sqrt(x^2 + y^2)
                h -> sqrt(4 * r^2 - x^2 - y^2)/2
                i -> (x - (y * sqrt(4 * r^2 - x^2 - y^2)) / sqrt(x^2 + y^2)) / 2 
                j -> (y + (x * sqrt(4 * r^2 - x^2 - y^2)) / sqrt(x^2 + y^2)) / 2
   
                Which can be written:
    
                i -> (x - (y * sqrt(4 * r^2 - x^2 - y^2))/sqrt(x^2 + y^2))/2
                j -> (y + (x * sqrt(4 * r^2 - x^2 - y^2))/sqrt(x^2 + y^2))/2
    
                Which we for size and speed reasons optimize to:
 
                h_x2_div_d = sqrt(4 * r^2 - x^2 - y^2)/sqrt(x^2 + y^2)
                i = (x - (y * h_x2_div_d))/2
                j = (y + (x * h_x2_div_d))/2       
            */      

            // First, use h_x2_div_d to compute 4*h^2 to check if it is negative or r is smaller
            // than d. If so, the sqrt of a negative number is complex and error out.
            float h_x2_div_d = 4.0 * gc_block.values.r*gc_block.values.r - x*x - y*y;

            if (h_x2_div_d < 0) { FAIL(STATUS_GCODE_ARC_RADIUS_ERROR); } // [Arc radius error]
    
            // Finish computing h_x2_div_d.
            h_x2_div_d = -sqrt(h_x2_div_d)/hypot_f(x,y); // == -(h * 2 / d)
            // Invert the sign of h_x2_div_d if the circle is counter clockwise (see sketch below)
            if (gc_block.modal.motion == MOTION_MODE_CCW_ARC) { h_x2_div_d = -h_x2_div_d; }  

            /* The counter clockwise circle lies to the left of the target direction. When offset is positive,
               the left hand circle will be generated - when it is negative the right hand circle is generated.
          
                                                                   T  <-- Target position
                                                   
                                                                   ^ 
                        Clockwise circles with this center         |          Clockwise circles with this center will have
                        will have > 180 deg of angular travel      |          < 180 deg of angular travel, which is a good thing!
                                                         \         |          /   
            center of arc when h_x2_div_d is positive ->  x <----- | -----> x <- center of arc when h_x2_div_d is negative
                                                                   |
                                                                   |
                                                   
                                                                   C  <-- Current position                                
            */  
            // Negative R is g-code-alese for "I want a circle with more than 180 degrees of travel" (go figure!), 
            // even though it is advised against ever generating such circles in a single line of g-code. By 
            // inverting the sign of h_x2_div_d the center of the circles is placed on the opposite side of the line of
            // travel and thus we get the unadvisably long arcs as prescribed.
            if (gc_block.values.r < 0) { 
                h_x2_div_d = -h_x2_div_d; 
                gc_block.values.r = -gc_block.values.r; // Finished with r. Set to positive for mc_arc
            }        
            // Complete the operation by calculating the actual center of the arc
            gc_block.values.ijk[axis_0] = 0.5*(x-(y*h_x2_div_d));
            gc_block.values.ijk[axis_1] = 0.5*(y+(x*h_x2_div_d));
          
          } else { // Arc Center Format Offset Mode  
            if (!(ijk_words & (bit(axis_0)|bit(axis_1)))) { FAIL(STATUS_GCODE_NO_OFFSETS_IN_PLANE); } // [No offsets in plane]
            bit_false(value_words,(bit(WORD_I)|bit(WORD_J)|bit(WORD_K)));  
          
            // Convert IJK values to proper units.
            if (gc_block.modal.units == UNITS_MODE_INCHES) {
              for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used to save flash space.
                if (ijk_words & bit(idx)) { gc_block.values.ijk[idx] *= MM_PER_INCH; }
              }
            }         
          
            x -= gc_block.values.ijk[axis_0]; // Delta x between circle center and target
            y -= gc_block.values.ijk[axis_1]; // Delta y between circle center and target
            float target_r = hypot_f(x,y);
            gc_block.values.r = hypot_f(gc_block.values.ijk[axis_0], gc_block.values.ijk[axis_1]); // Compute arc radius for mc_arc

            if (fabs(target_r-gc_block.values.r) > 0.002) { FAIL(STATUS_GCODE_INVALID_TARGET); } // [Arc definition error]
          }
          break;
        case MOTION_MODE_PROBE:
          // [G38 Errors]: Target is same current. No axis words. Cutter compensation is enabled. Feed rate
          //   is undefined. Probe is triggered.
          if (gc_check_same_position(gc_state.position, gc_block.values.xyz)) { FAIL(STATUS_GCODE_INVALID_TARGET); } // [Invalid target]
          if (probe_get_state()) { FAIL(STATUS_GCODE_PROBE_TRIGGERED); } // [Probe triggered]
          break;
      } 
    }
  }
  
  // [21. Program flow ]: No error check required.

  // [0. Non-specific error-checks]: Complete unused value words check, i.e. IJK used when in arc
  // radius mode, or axis words that aren't used in the block.  
  bit_false(value_words,(bit(WORD_N)|bit(WORD_F)|bit(WORD_S)|bit(WORD_T))); // Remove single-meaning value words. 
  if (axis_explicit) { bit_false(value_words,(bit(WORD_X)|bit(WORD_Y)|bit(WORD_Z))); } // Remove axis words. 
  if (value_words) { FAIL(STATUS_GCODE_UNUSED_WORDS); } // [Unused words]

   
  /* -------------------------------------------------------------------------------------
     STEP 4: EXECUTE!!
     Assumes that all error-checking has been completed and no failure modes exist. We just
     need to update the state and execute the block according to the order-of-execution.
  */ 
  
  // [1. Comments feedback ]:  NOT SUPPORTED
  
  // [2. Set feed rate mode ]:
  gc_state.modal.feed_rate = gc_block.modal.feed_rate;
  
  // [3. Set feed rate ]:
  gc_state.feed_rate = gc_block.values.f; // Always copy this value. See feed rate error-checking.

  // [4. Set spindle speed ]:
  if (gc_state.spindle_speed != gc_block.values.s) { 
    gc_state.spindle_speed = gc_block.values.s; 
    
    // Update running spindle only if not in check mode and not already enabled.
    if (gc_state.modal.spindle != SPINDLE_DISABLE) { spindle_run(gc_state.modal.spindle, gc_state.spindle_speed); }
  }
    
  // [5. Select tool ]: NOT SUPPORTED

  // [6. Change tool ]: NOT SUPPORTED

  // [7. Spindle control ]:
  if (gc_state.modal.spindle != gc_block.modal.spindle) {
    gc_state.modal.spindle = gc_block.modal.spindle;    
    // Update spindle control and apply spindle speed when enabling it in this block.    
    spindle_run(gc_state.modal.spindle, gc_state.spindle_speed);
  }

  // [8. Coolant control ]:  
  if (gc_state.modal.coolant != gc_block.modal.coolant) {
    gc_state.modal.coolant = gc_block.modal.coolant;
    coolant_run(gc_state.modal.coolant);
  }
  
  // [9. Enable/disable feed rate or spindle overrides ]: NOT SUPPORTED

  // [10. Dwell ]:
  if (gc_block.non_modal_command == NON_MODAL_DWELL) { mc_dwell(gc_block.values.p); }
  
  // [11. Set active plane ]:
  gc_state.modal.plane_select = gc_block.modal.plane_select;  

  // [12. Set length units ]:
  gc_state.modal.units = gc_block.modal.units;

  // [13. Cutter radius compensation ]: NOT SUPPORTED

  // [14. Cutter length compensation ]: NOT SUPPORTED
  
  // [15. Coordinate system selection ]:
  if (gc_state.modal.coord_select != gc_block.modal.coord_select) {
    gc_state.modal.coord_select = gc_block.modal.coord_select;
    memcpy(gc_state.coord_system,coordinate_data,sizeof(coordinate_data));
  }
  
  // [16. Set path control mode ]: NOT SUPPORTED
  
  // [17. Set distance mode ]:
  gc_state.modal.distance = gc_block.modal.distance;
  
  // [18. Set retract mode ]: NOT SUPPORTED
    
  // [19. Go to predefined position, Set G10, or Set axis offsets ]:
  switch(gc_block.non_modal_command) {
    case NON_MODAL_SET_COORDINATE_DATA:

// TODO: See if I can clean up this int_value.
      int_value = trunc(gc_block.values.p); // Convert p value to int.
      if (int_value > 0) { int_value--; } // Adjust P1-P6 index to EEPROM coordinate data indexing.
      else { int_value = gc_state.modal.coord_select; } // Index P0 as the active coordinate system
      
      settings_write_coord_data(int_value,parameter_data);
      // Update system coordinate system if currently active.
      if (gc_state.modal.coord_select == int_value) { memcpy(gc_state.coord_system,parameter_data,sizeof(parameter_data)); }
      break;
    case NON_MODAL_GO_HOME_0: case NON_MODAL_GO_HOME_1: 
      // Move to intermediate position before going home. Obeys current coordinate system and offsets 
      // and absolute and incremental modes.
      if (axis_explicit) {
        #ifdef USE_LINE_NUMBERS
        mc_line(gc_block.values.xyz, -1.0, false, gc_block.values.n);
        #else
        mc_line(gc_block.values.xyz, -1.0, false);
        #endif
      }
      #ifdef USE_LINE_NUMBERS
      mc_line(parameter_data, -1.0, false, gc_block.values.n); 
      #else
      mc_line(parameter_data, -1.0, false); 
      #endif
      memcpy(gc_state.position, parameter_data, sizeof(parameter_data));
      break;
    case NON_MODAL_SET_HOME_0: 
      settings_write_coord_data(SETTING_INDEX_G28,gc_state.position);
      break;
    case NON_MODAL_SET_HOME_1:
      settings_write_coord_data(SETTING_INDEX_G30,gc_state.position);
      break;
    case NON_MODAL_SET_COORDINATE_OFFSET:
      memcpy(gc_state.coord_offset,gc_block.values.xyz,sizeof(gc_block.values.xyz));
      break;
    case NON_MODAL_RESET_COORDINATE_OFFSET: 
      clear_vector(gc_state.coord_offset); // Disable G92 offsets by zeroing offset vector.
      break;
  }

  
  // [20. Motion modes ]:
  // NOTE: Commands G10,G28,G30,G92 lock out and prevent axis words from use in motion modes. 
  // Enter motion modes only if there are axis words or a motion mode command word in the block.
  gc_state.modal.motion = gc_block.modal.motion;
  if (gc_state.modal.motion != MOTION_MODE_NONE) {
    if (axis_explicit == AXIS_COMMAND_MOTION_MODE) {
      switch (gc_state.modal.motion) {
        case MOTION_MODE_SEEK:
          #ifdef USE_LINE_NUMBERS
          mc_line(gc_block.values.xyz, -1.0, false, gc_block.values.n);
          #else
          mc_line(gc_block.values.xyz, -1.0, false);
          #endif
          break;
        case MOTION_MODE_LINEAR:
          #ifdef USE_LINE_NUMBERS
          mc_line(gc_block.values.xyz, gc_state.feed_rate, gc_state.modal.feed_rate, gc_block.values.n);
          #else
          mc_line(gc_block.values.xyz, gc_state.feed_rate, gc_state.modal.feed_rate);
          #endif
          break;
        case MOTION_MODE_CW_ARC: case MOTION_MODE_CCW_ARC:
          #ifdef USE_LINE_NUMBERS
          mc_arc(gc_state.position, gc_block.values.xyz, gc_block.values.ijk, gc_block.values.r, 
            gc_state.feed_rate, gc_state.modal.feed_rate, axis_0, axis_1, axis_linear, gc_block.values.n);  
          #else
          mc_arc(gc_state.position, gc_block.values.xyz, gc_block.values.ijk, gc_block.values.r, 
            gc_state.feed_rate, gc_state.modal.feed_rate, axis_0, axis_1, axis_linear); 
          #endif
          break;
        case MOTION_MODE_PROBE:
          #ifdef USE_LINE_NUMBERS
          mc_probe_cycle(gc_block.values.xyz, gc_state.feed_rate, gc_state.modal.feed_rate, gc_block.values.n);
          #else
          mc_probe_cycle(gc_block.values.xyz, gc_state.feed_rate, gc_state.modal.feed_rate);
          #endif
      }
    
      // As far as the parser is concerned, the position is now == target. In reality the
      // motion control system might still be processing the action and the real tool position
      // in any intermediate location.
      memcpy(gc_state.position, gc_block.values.xyz, sizeof(gc_block.values.xyz)); // gc.position[] = target[];
    }
  }
  
  // [21. Program flow ]:
  // M0,M1,M2,M30: Perform non-running program flow actions. During a program pause, the buffer may 
  // refill and can only be resumed by the cycle start run-time command.
  gc_state.modal.program_flow = gc_block.modal.program_flow;
  if (gc_state.modal.program_flow) { 
    protocol_buffer_synchronize(); // Finish all remaining buffered motions. Program paused when complete.
    sys.auto_start = false; // Disable auto cycle start. Forces pause until cycle start issued.
  
    // If complete, reset to reload defaults (G92.2,G54,G17,G90,G94,M48,G40,M5,M9). Otherwise,
    // re-enable program flow after pause complete, where cycle start will resume the program.
    if (gc_state.modal.program_flow == PROGRAM_FLOW_COMPLETED) { mc_reset(); }
    else { gc_state.modal.program_flow = PROGRAM_FLOW_RUNNING; }
  }
    
  // TBD: % to denote start of program. Sets auto cycle start?
  return(STATUS_OK);
}
        

/* 
  Not supported:

  - Canned cycles
  - Tool radius compensation
  - A,B,C-axes
  - Evaluation of expressions
  - Variables
  - Override control (TBD)
  - Tool changes
  - Switches
   
   (*) Indicates optional parameter, enabled through config.h and re-compile
   group 0 = {G92.2, G92.3} (Non modal: Cancel and re-enable G92 offsets)
   group 1 = {G81 - G89} (Motion modes: Canned cycles)
   group 4 = {M1} (Optional stop, ignored)
   group 6 = {M6} (Tool change)
   group 8 = {*M7} enable mist coolant
   group 9 = {M48, M49} enable/disable feed and speed override switches
   group 13 = {G61, G61.1, G64} path control mode
*/