grbl-LPC-CoreXY/main.c

/*
  main.c - An embedded CNC Controller with rs274/ngc (g-code) support
  Part of Grbl

  Copyright (c) 2009-2011 Simen Svale Skogsrud
  Copyright (c) 2011-2012 Sungeun K. Jeon

  Grbl is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  Grbl is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with Grbl.  If not, see <http://www.gnu.org/licenses/>.
*/

/* A big thanks to Alden Hart of Synthetos, supplier of grblshield and TinyG, who has
   been integral throughout the development of the higher level details of Grbl, as well
   as being a consistent sounding board for the future of accessible and free CNC. */

#include <avr/interrupt.h>
#include <avr/pgmspace.h>
#include "config.h"
#include "planner.h"
#include "nuts_bolts.h"
#include "stepper.h"
#include "spindle_control.h"
#include "coolant_control.h"
#include "motion_control.h"
#include "gcode.h"
#include "protocol.h"
#include "limits.h"
#include "report.h"
#include "settings.h"
#include "serial.h"

// Declare system global variable structure
system_t sys; 

int main(void)
{
  // Initialize system
  serial_init(BAUD_RATE); // Setup serial baud rate and interrupts
  st_init(); // Setup stepper pins and interrupt timers
  sei(); // Enable interrupts

  memset(&sys, 0, sizeof(sys));  // Clear all system variables
  sys.abort = true;   // Set abort to complete initialization

  // TODO: When Grbl system status is installed, need to set position lost state upon startup.
               
  for(;;) {
  
    // Execute system reset upon a system abort, where the main program will return to this loop.
    // Once here, it is safe to re-initialize the system. At startup, the system will automatically
    // reset to finish the initialization process.
    if (sys.abort) {
      
      // Retain last known machine position and work coordinate offset(s). If the system abort
      // occurred while in motion, machine position is not guaranteed, since a hard stop can cause
      // the steppers to lose steps. Always perform a feedhold before an abort, if maintaining
      // accurate machine position is required.
      // TODO: Report last position and coordinate offset to users to help relocate origins. Future
      // releases will auto-reset the machine position back to [0,0,0] if an abort is used while 
      // grbl is moving the machine.
      int32_t last_position[3];
      memcpy(last_position, sys.position, sizeof(sys.position)); // last_position[] = sys.position[]
      // TODO: Last coordinate system method.
      
      // Reset system.
      memset(&sys, 0, sizeof(sys)); // Clear all system variables
      serial_reset_read_buffer(); // Clear serial read buffer
      settings_init(); // Load grbl settings from EEPROM
      protocol_init(); // Clear incoming line data
      plan_init(); // Clear block buffer and planner variables
      gc_init(); // Set g-code parser to default state
      spindle_init();
      coolant_init();
      limits_init();
      st_reset(); // Clear stepper subsystem variables.
      
      // Reload last known machine position and work systems. G92 coordinate offsets are reset.
      memcpy(sys.position, last_position, sizeof(last_position)); // sys.position[] = last_position[]
      gc_set_current_position(last_position[X_AXIS],last_position[Y_AXIS],last_position[Z_AXIS]);
      plan_set_current_position(last_position[X_AXIS],last_position[Y_AXIS],last_position[Z_AXIS]);
      
      // Set system runtime defaults
      // TODO: Eventual move to EEPROM from config.h when all of the new settings are worked out. 
      // Mainly to avoid having to maintain several different versions.
      if (bit_istrue(settings.flags,BITFLAG_AUTO_START)) {
        sys.auto_start = true;
      }
      // TODO: Install G20/G21 unit default into settings and load appropriate settings.

      report_init_message();
    }
    
    protocol_execute_runtime();
    protocol_process(); // ... process the serial protocol
    
  }
  return 0;   /* never reached */
}