ManuelW/espurna-sonoff-pow
1
0
Fork 0
Code Issues Pull Requests Releases 1 Wiki Activity
90c39b1fc2
espurna-sonoff-pow/espurna/config/hardware.h
Manuel Weiser aece7ca1b0 Initial
2018-06-06 15:28:17 +02:00

2024 lines
62 KiB
C
Executable File
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

// -----------------------------------------------------------------------------
// Configuration HELP
// -----------------------------------------------------------------------------
//
// MANUFACTURER: Name of the manufacturer of the board ("string")
// DEVICE: Name of the device ("string")
// BUTTON#_PIN: GPIO for the n-th button (1-based, up to 4 buttons)
// BUTTON#_RELAY: Relay number that will be bind to the n-th button (1-based)
// BUTTON#_MODE: A mask of options (BUTTON_PUSHBUTTON and BUTTON_SWITCH cannot be together)
// - BUTTON_PUSHBUTTON: button event is fired when released
// - BUTTON_SWITCH: button event is fired when pressed or released
// - BUTTON_DEFAULT_HIGH: there is a pull up in place
// - BUTTON_SET_PULLUP: set pullup by software
// RELAY#_PIN: GPIO for the n-th relay (1-based, up to 8 relays)
// RELAY#_TYPE: Relay can be RELAY_TYPE_NORMAL, RELAY_TYPE_INVERSE, RELAY_TYPE_LATCHED or RELAY_TYPE_LATCHED_INVERSE
// LED#_PIN: GPIO for the n-th LED (1-based, up to 8 LEDs)
// LED#_PIN_INVERSE: LED has inversed logic (lit when pulled down)
// LED#_MODE: Check general.h for LED_MODE_%
// LED#_RELAY: Linked relay (1-based)
//
// Besides, other hardware specific information should be stated here
// -----------------------------------------------------------------------------
// ESPurna Core
// -----------------------------------------------------------------------------
#if defined(ESPURNA_CORE)
// This is a special device targeted to generate a light-weight binary image
// meant to be able to do two-step-updates:
// https://github.com/xoseperez/espurna/wiki/TwoStepUpdates
// Info
#define MANUFACTURER "ESPRESSIF"
#define DEVICE "ESPURNA_CORE"
// Disable non-core modules
#define ALEXA_SUPPORT 0
#define BROKER_SUPPORT 0
#define DOMOTICZ_SUPPORT 0
#define HOMEASSISTANT_SUPPORT 0
#define I2C_SUPPORT 0
#define MQTT_SUPPORT 0
#define NTP_SUPPORT 0
#define SCHEDULER_SUPPORT 0
#define SENSOR_SUPPORT 0
#define THINGSPEAK_SUPPORT 0
#define WEB_SUPPORT 0
// -----------------------------------------------------------------------------
// Development boards
// -----------------------------------------------------------------------------
#elif defined(NODEMCU_LOLIN)
// Info
#define MANUFACTURER "NODEMCU"
#define DEVICE "LOLIN"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#elif defined(WEMOS_D1_MINI_RELAYSHIELD)
// Info
#define MANUFACTURER "WEMOS"
#define DEVICE "D1_MINI_RELAYSHIELD"
// Buttons
// No buttons on the D1 MINI alone, but defining it without adding a button doen't create problems
#define BUTTON1_PIN 0 // Connect a pushbutton between D3 and GND,
// it's the same as using a Wemos one button shield
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 15
#define BUTTON2_RELAY 1
#define BUTTON2_MODE BUTTON_PUSHBUTTON
#define BUTTON2_PRESS BUTTON_MODE_ON
#define BUTTON2_CLICK BUTTON_MODE_OFF
#define BUTTON2_DBLCLICK BUTTON_MODE_OFF
#define BUTTON2_LNGCLICK BUTTON_MODE_OFF
#define BUTTON2_LNGLNGCLICK BUTTON_MODE_OFF
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 12
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// When Wemos relay shield is connected GPIO5 (D1) is used for relay,
// so I2C must be remapped to other pins
//#define I2C_SDA_PIN 12 // D6
//#define I2C_SCL_PIN 14 // D5
#elif defined(WEMOS_D1_TARPUNA_SHIELD)
// Info
#define MANUFACTURER "WEMOS"
#define DEVICE "D1_TARPUNA_SHIELD"
// -----------------------------------------------------------------------------
// ESPurna
// -----------------------------------------------------------------------------
#elif defined(TINKERMAN_ESPURNA_H06)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "ESPURNA_H06"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
// Normal pushbutton
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_INVERSE
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 2
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 14
#elif defined(TINKERMAN_ESPURNA_H08)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "ESPURNA_H08"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
// Normal pushbutton
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 5
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 14
#elif defined(TINKERMAN_ESPURNA_SWITCH)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "ESPURNA_SWITCH"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
// Touch button
#define BUTTON1_MODE BUTTON_PUSHBUTTON
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_INVERSE
// -----------------------------------------------------------------------------
// Itead Studio boards
// -----------------------------------------------------------------------------
#elif defined(ITEAD_SONOFF_BASIC)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_BASIC"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 14
#define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON2_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_RF)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_RF"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 14
#define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON2_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_TH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_TH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Jack is connected to GPIO14 (and with a small hack to GPIO4)
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 14
#ifndef DHT_SUPPORT
#define DHT_SUPPORT 1
#endif
#define DHT_PIN 14
//#define I2C_SDA_PIN 4
//#define I2C_SCL_PIN 14
#elif defined(ITEAD_SONOFF_SV)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_SV"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SLAMPHER)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SLAMPHER"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_S20)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "S20"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_TOUCH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_TOUCH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_POW)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_POW"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 15
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 5
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 14
#elif defined(ITEAD_SONOFF_DUAL)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_DUAL"
#define SERIAL_BAUDRATE 19230
#define RELAY_PROVIDER RELAY_PROVIDER_DUAL
#define DUMMY_RELAY_COUNT 2
#define DEBUG_SERIAL_SUPPORT 0
#define TERMINAL_SUPPORT 0
// Buttons
#define BUTTON3_RELAY 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_DUAL_R2)
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_DUAL_R2"
// Buttons
#define BUTTON1_PIN 0 // Button 0 on header
#define BUTTON2_PIN 9 // Button 1 on header
#define BUTTON3_PIN 10 // Physical button
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 1
#define BUTTON1_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_4CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_4CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON4_PIN 14
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON4_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
#define BUTTON4_RELAY 4
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY4_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_4CH_PRO)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_4CH_PRO"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON4_PIN 14
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON4_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
#define BUTTON4_RELAY 4
// Sonoff 4CH Pro uses a secondary STM32 microcontroller to handle
// buttons and relays, but it also forwards button presses to the ESP8285.
// This allows ESPurna to handle button presses -almost- the same way
// as with other devices except:
// * Double click seems to break/disable the button on the STM32 side
// * With S6 switch to 1 (self-locking and inching modes) everything's OK
// * With S6 switch to 0 (interlock mode) if there is a relay ON
// and you click on another relay button, the STM32 sends a "press"
// event for the button of the first relay (to turn it OFF) but it
// does not send a "release" event. It's like it's holding the
// button down since you can see it is still LOW.
// Whatever reason the result is that it may actually perform a
// long click or long-long click.
// The configuration below make the button toggle the relay on press events
// and disables any possibly harmful combination with S6 set to 0.
// If you are sure you will only use S6 to 1 you can comment the
// BUTTON1_LNGCLICK and BUTTON1_LNGLNGCLICK options below to recover the
// reset mode and factory reset functionalities, or link other actions like
// AP mode in the commented line below.
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
//#define BUTTON1_LNGCLICK BUTTON_MODE_AP
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE
#define BUTTON2_PRESS BUTTON_MODE_TOGGLE
#define BUTTON2_CLICK BUTTON_MODE_NONE
#define BUTTON3_PRESS BUTTON_MODE_TOGGLE
#define BUTTON3_CLICK BUTTON_MODE_NONE
#define BUTTON4_PRESS BUTTON_MODE_TOGGLE
#define BUTTON4_CLICK BUTTON_MODE_NONE
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY4_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_1CH_INCHING)
// The inching functionality is managed by a misterious IC in the board.
// You cannot control the inching button and functionality from the ESP8266
// Besides, enabling the inching functionality using the hardware button
// will result in the relay switching on and off continuously.
// Fortunately the unkown IC keeps memory of the hardware inching status
// so you can just disable it and forget. The inching LED must be lit.
// You can still use the pulse options from the web interface
// without problem.
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "1CH_INCHING"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_MOTOR)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "MOTOR"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_BNSZ01)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "BNSZ01"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 1
#define LIGHT_CH1_PIN 12
#define LIGHT_CH1_INVERSE 0
#elif defined(ITEAD_SONOFF_RFBRIDGE)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_RFBRIDGE"
#define SERIAL_BAUDRATE 19200
#define RELAY_PROVIDER RELAY_PROVIDER_RFBRIDGE
#ifndef DUMMY_RELAY_COUNT
#define DUMMY_RELAY_COUNT 8
#endif
// Remove UART noise on serial line
#define TERMINAL_SUPPORT 0
#define DEBUG_SERIAL_SUPPORT 0
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_B1)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_B1"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define MY92XX_MODEL MY92XX_MODEL_MY9231
#define MY92XX_CHIPS 2
#define MY92XX_DI_PIN 12
#define MY92XX_DCKI_PIN 14
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 4, 3, 5, 0, 1
#elif defined(ITEAD_SONOFF_LED)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_LED"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 2
#define LIGHT_CH1_PIN 12 // Cold white
#define LIGHT_CH2_PIN 14 // Warm white
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#elif defined(ITEAD_SONOFF_T1_1CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_T1_1CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_T1_2CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_T1_2CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_MODE_TOGGLE
#define BUTTON2_CLICK BUTTON_MODE_NONE
#define BUTTON2_DBLCLICK BUTTON_MODE_NONE
#define BUTTON2_LNGCLICK BUTTON_MODE_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_T1_3CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_T1_3CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_MODE_TOGGLE
#define BUTTON2_CLICK BUTTON_MODE_NONE
#define BUTTON2_DBLCLICK BUTTON_MODE_NONE
#define BUTTON2_LNGCLICK BUTTON_MODE_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_PRESS BUTTON_MODE_TOGGLE
#define BUTTON3_CLICK BUTTON_MODE_NONE
#define BUTTON3_DBLCLICK BUTTON_MODE_NONE
#define BUTTON3_LNGCLICK BUTTON_MODE_NONE
#define BUTTON3_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_S31)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_S31"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Disable UART noise
#define TERMINAL_SUPPORT 0
#define DEBUG_SERIAL_SUPPORT 0
// CSE7766
#define CSE7766_SUPPORT 1
#define CSE7766_PIN 1
// -----------------------------------------------------------------------------
// YJZK
// -----------------------------------------------------------------------------
#elif defined(YJZK_SWITCH_2CH)
// Info
#define MANUFACTURER "YJZK"
#define DEVICE "SWITCH_2CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Electrodragon boards
// -----------------------------------------------------------------------------
#elif defined(ELECTRODRAGON_WIFI_IOT)
// Info
#define MANUFACTURER "ELECTRODRAGON"
#define DEVICE "WIFI_IOT"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 2
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 13
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 16
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// WorkChoice ecoPlug
// -----------------------------------------------------------------------------
#elif defined(WORKCHOICE_ECOPLUG)
// Info
#define MANUFACTURER "WORKCHOICE"
#define DEVICE "ECOPLUG"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// AI Thinker
// -----------------------------------------------------------------------------
#elif defined(AITHINKER_AI_LIGHT)
// Info
#define MANUFACTURER "AITHINKER"
#define DEVICE "AI_LIGHT"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define MY92XX_MODEL MY92XX_MODEL_MY9291
#define MY92XX_CHIPS 1
#define MY92XX_DI_PIN 13
#define MY92XX_DCKI_PIN 15
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 0, 1, 2, 3
// -----------------------------------------------------------------------------
// LED Controller
// -----------------------------------------------------------------------------
#elif defined(MAGICHOME_LED_CONTROLLER)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "LED_CONTROLLER"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 13 // WHITE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
// IR
#define IR_SUPPORT 1
#define IR_PIN 4
#define IR_BUTTON_SET 1
#elif defined(MAGICHOME_LED_CONTROLLER_20)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "LED_CONTROLLER_20"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
// IR
#define IR_SUPPORT 1
#define IR_PIN 4
#define IR_BUTTON_SET 1
// -----------------------------------------------------------------------------
// HUACANXING H801 & H802
// -----------------------------------------------------------------------------
#elif defined(HUACANXING_H801)
// Info
#define MANUFACTURER "HUACANXING"
#define DEVICE "H801"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define DEBUG_PORT Serial1
#define SERIAL_RX_ENABLED 1
// LEDs
#define LED1_PIN 5
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 15 // RED
#define LIGHT_CH2_PIN 13 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 14 // WHITE1
#define LIGHT_CH5_PIN 4 // WHITE2
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#define LIGHT_CH5_INVERSE 0
#elif defined(HUACANXING_H802)
// Info
#define MANUFACTURER "HUACANXING"
#define DEVICE "H802"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define DEBUG_PORT Serial1
#define SERIAL_RX_ENABLED 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 12 // RED
#define LIGHT_CH2_PIN 14 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
// -----------------------------------------------------------------------------
// Jan Goedeke Wifi Relay
// https://github.com/JanGoe/esp8266-wifi-relay
// -----------------------------------------------------------------------------
#elif defined(JANGOE_WIFI_RELAY_NC)
// Info
#define MANUFACTURER "JANGOE"
#define DEVICE "WIFI_RELAY_NC"
// Buttons
#define BUTTON1_PIN 12
#define BUTTON2_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 2
#define RELAY2_PIN 14
#define RELAY1_TYPE RELAY_TYPE_INVERSE
#define RELAY2_TYPE RELAY_TYPE_INVERSE
#elif defined(JANGOE_WIFI_RELAY_NO)
// Info
#define MANUFACTURER "JANGOE"
#define DEVICE "WIFI_RELAY_NO"
// Buttons
#define BUTTON1_PIN 12
#define BUTTON2_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 2
#define RELAY2_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// Jorge García Wifi+Relays Board Kit
// https://www.tindie.com/products/jorgegarciadev/wifi--relays-board-kit
// https://github.com/jorgegarciadev/wifikit
// -----------------------------------------------------------------------------
#elif defined(JORGEGARCIA_WIFI_RELAYS)
// Info
#define MANUFACTURER "JORGEGARCIA"
#define DEVICE "WIFI_RELAYS"
// Relays
#define RELAY1_PIN 0
#define RELAY2_PIN 2
#define RELAY1_TYPE RELAY_TYPE_INVERSE
#define RELAY2_TYPE RELAY_TYPE_INVERSE
// -----------------------------------------------------------------------------
// WiFi MQTT Relay / Thermostat
// -----------------------------------------------------------------------------
#elif defined(OPENENERGYMONITOR_MQTT_RELAY)
// Info
#define MANUFACTURER "OPENENERGYMONITOR"
#define DEVICE "MQTT_RELAY"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 16
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// WiOn 50055 Indoor Wi-Fi Wall Outlet & Tap
// https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50050-Indoor-Wi-Fi-Outlet-Wireless-Switch-Programmable-Timer-%2F263112281551
// https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50055-Indoor-Wi-Fi-Wall-Tap-Monitor-Energy-Usage-Wireless-Smart-Switch-%2F263020837777
// -----------------------------------------------------------------------------
#elif defined(WION_50055)
// Currently untested, does not support energy monitoring
// Info
#define MANUFACTURER "WION"
#define DEVICE "50055"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// EX-Store Wifi Relay v3.1
// https://ex-store.de/ESP8266-WiFi-Relay-V31
// -----------------------------------------------------------------------------
#elif defined(EXS_WIFI_RELAY_V31)
// Untested
// Info
#define MANUFACTURER "EXS"
#define DEVICE "WIFI_RELAY_V31"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 13
#define RELAY1_TYPE RELAY_TYPE_LATCHED
#define RELAY1_RESET_PIN 12
// -----------------------------------------------------------------------------
// V9261F
// -----------------------------------------------------------------------------
#elif defined(GENERIC_V9261F)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "V9261F"
#define ALEXA_SUPPORT 0
// V9261F
#define V9261F_SUPPORT 1
#define V9261F_PIN 2
#define V9261F_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// ECH1560
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ECH1560)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ECH1560"
#define ALEXA_SUPPORT 0
// ECH1560
#define ECH1560_SUPPORT 1
#define ECH1560_CLK_PIN 4
#define ECH1560_MISO_PIN 5
#define ECH1560_INVERTED 0
// -----------------------------------------------------------------------------
// ESPLive
// https://github.com/ManCaveMade/ESP-Live
// -----------------------------------------------------------------------------
#elif defined(MANCAVEMADE_ESPLIVE)
// Info
#define MANUFACTURER "MANCAVEMADE"
#define DEVICE "ESPLIVE"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON2_PIN 5
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 13
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// DB18B20
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 2
#define DALLAS_UPDATE_INTERVAL 5000
#define TEMPERATURE_MIN_CHANGE 1.0
// -----------------------------------------------------------------------------
// QuinLED
// http://blog.quindorian.org/2017/02/esp8266-led-lighting-quinled-v2-6-pcb.html
// -----------------------------------------------------------------------------
#elif defined(INTERMITTECH_QUINLED)
// Info
#define MANUFACTURER "INTERMITTECH"
#define DEVICE "QUINLED"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 5
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 2
#define LIGHT_CH1_PIN 0
#define LIGHT_CH2_PIN 2
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
// -----------------------------------------------------------------------------
// Arilux AL-LC06
// -----------------------------------------------------------------------------
#elif defined(ARILUX_AL_LC01)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC01"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 14 // WHITE1
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#elif defined(ARILUX_AL_LC02)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC02"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 12 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE1
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#elif defined(ARILUX_AL_LC06)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC06"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE1
#define LIGHT_CH5_PIN 5 // WHITE2
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#define LIGHT_CH5_INVERSE 0
#elif defined(ARILUX_AL_LC11)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC11"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 4 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 13 // WHITE1
#define LIGHT_CH5_PIN 12 // WHITE1
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#define LIGHT_CH5_INVERSE 0
#elif defined(ARILUX_E27)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "E27"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define MY92XX_MODEL MY92XX_MODEL_MY9291
#define MY92XX_CHIPS 1
#define MY92XX_DI_PIN 13
#define MY92XX_DCKI_PIN 15
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 0, 1, 2, 3
// -----------------------------------------------------------------------------
// XENON SM-PW701U
// -----------------------------------------------------------------------------
#elif defined(XENON_SM_PW702U)
// Info
#define MANUFACTURER "XENON"
#define DEVICE "SM_PW702U"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// AUTHOMETION LYT8266
// https://authometion.com/shop/en/home/13-lyt8266.html
// -----------------------------------------------------------------------------
#elif defined(AUTHOMETION_LYT8266)
// Info
#define MANUFACTURER "AUTHOMETION"
#define DEVICE "LYT8266"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 13 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 2 // WHITE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#define LIGHT_ENABLE_PIN 15
#elif defined(GIZWITS_WITTY_CLOUD)
// Info
#define MANUFACTURER "GIZWITS"
#define DEVICE "WITTY_CLOUD"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define ANALOG_SUPPORT 1
// LEDs
#define LED1_PIN 2 // BLUE build-in
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 3
#define LIGHT_CH1_PIN 15 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
// -----------------------------------------------------------------------------
// KMC 70011
// https://www.amazon.com/KMC-Monitoring-Required-Control-Compatible/dp/B07313TH7B
// -----------------------------------------------------------------------------
#elif defined(KMC_70011)
// Info
#define MANUFACTURER "KMC"
#define DEVICE "70011"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor
// -----------------------------------------------------------------------------
// Euromate (?) Wifi Stecker Shuko
// https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko/p/2291706
// Thanks to @Geitde
// -----------------------------------------------------------------------------
#elif defined(EUROMATE_WIFI_STECKER_SCHUKO)
// Info
#define MANUFACTURER "EUROMATE"
#define DEVICE "WIFI_STECKER_SCHUKO"
// Buttons
#define BUTTON1_PIN 14
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// The relay in the device is not a bistable (latched) relay.
// The device is reported to have a flip-flop circuit to drive the relay
// So @Geitde hack is still the only possible
// Hack: drive GPIO12 low and use GPIO5 as normal relay pin:
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define LED2_PIN 12 /* DUMMY: exploit default off state for GPIO12=low */
#define LED2_PIN_INVERSE 0
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Generic 8CH
// -----------------------------------------------------------------------------
#elif defined(GENERIC_8CH)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "8CH"
// Relays
#define RELAY1_PIN 0
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 2
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_PIN 4
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_PIN 5
#define RELAY4_TYPE RELAY_TYPE_NORMAL
#define RELAY5_PIN 12
#define RELAY5_TYPE RELAY_TYPE_NORMAL
#define RELAY6_PIN 13
#define RELAY6_TYPE RELAY_TYPE_NORMAL
#define RELAY7_PIN 14
#define RELAY7_TYPE RELAY_TYPE_NORMAL
#define RELAY8_PIN 15
#define RELAY8_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// STM RELAY
// -----------------------------------------------------------------------------
#elif defined(STM_RELAY)
// Info
#define MANUFACTURER "STM_RELAY"
#define DEVICE "2CH"
// Relays
#define DUMMY_RELAY_COUNT 2
#define RELAY_PROVIDER RELAY_PROVIDER_STM
// Remove UART noise on serial line
#define TERMINAL_SUPPORT 0
#define DEBUG_SERIAL_SUPPORT 0
// -----------------------------------------------------------------------------
// Tonbux Powerstrip02
// -----------------------------------------------------------------------------
#elif defined(TONBUX_POWERSTRIP02)
// Info
#define MANUFACTURER "TONBUX"
#define DEVICE "POWERSTRIP02"
// Buttons
#define BUTTON1_PIN 5
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 0
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_INVERSE
#define RELAY2_PIN 13
#define RELAY2_TYPE RELAY_TYPE_INVERSE
#define RELAY3_PIN 12
#define RELAY3_TYPE RELAY_TYPE_INVERSE
#define RELAY4_PIN 14
#define RELAY4_TYPE RELAY_TYPE_INVERSE
// Not a relay. USB ports on/off
#define RELAY5_PIN 16
#define RELAY5_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0 // 1 blue led
#define LED1_PIN_INVERSE 1
#define LED2_PIN 3 // 3 red leds
#define LED2_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Lingan SWA1
// -----------------------------------------------------------------------------
#elif defined(LINGAN_SWA1)
// Info
#define MANUFACTURER "LINGAN"
#define DEVICE "SWA1"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// HEYGO HY02
// -----------------------------------------------------------------------------
#elif defined(HEYGO_HY02)
// Info
#define MANUFACTURER "HEYGO"
#define DEVICE "HY02"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Maxcio W-US002S
// -----------------------------------------------------------------------------
#elif defined(MAXCIO_WUS002S)
// Info
#define MANUFACTURER "MAXCIO"
#define DEVICE "WUS002S"
// Buttons
#define BUTTON1_PIN 2
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 13
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 3
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_CURRENT_R 0.002 // Current resistor
#define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor
// -----------------------------------------------------------------------------
// YiDian XS-SSA05
// -----------------------------------------------------------------------------
#elif defined(YIDIAN_XSSSA05)
// Info
#define MANUFACTURER "YIDIAN"
#define DEVICE "XSSSA05"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 3
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_CURRENT_R 0.001 // Current resistor
#define HLW8012_VOLTAGE_R_UP ( 2 * 1200000 ) // Upstream voltage resistor
// -----------------------------------------------------------------------------
// TONBUX XS-SSA06
// -----------------------------------------------------------------------------
#elif defined(TONBUX_XSSSA06)
// Info
#define MANUFACTURER "TONBUX"
#define DEVICE "XSSSA06"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0 // R - 8 rgb led ring
#define LED1_PIN_INVERSE 0
#define LED2_PIN 5 // G
#define LED2_PIN_INVERSE 0
#define LED3_PIN 2 // B
#define LED3_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// GREEN ESP8266 RELAY MODULE
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180323113846&SearchText=Green+ESP8266
// -----------------------------------------------------------------------------
#elif defined(GREEN_ESP8266RELAY)
// Info
#define MANUFACTURER "GREEN"
#define DEVICE "ESP8266RELAY"
// Buttons
// Not a button but input via Optocoupler
#define BUTTON1_PIN 5
#define BUTTON1_MODE BUTTON_PUSHBUTTON
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Henrique Gravina ESPIKE
// https://github.com/Henriquegravina/Espike
// -----------------------------------------------------------------------------
#elif defined(IKE_ESPIKE)
#define MANUFACTURER "IKE"
#define DEVICE "ESPIKE"
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_PIN 13
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PIN 12
#define BUTTON2_RELAY 2
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_PIN 14
#define BUTTON3_RELAY 2
#define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 5
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_PIN 16
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// SWIFITCH
// https://github.com/ArnieX/swifitch
// -----------------------------------------------------------------------------
#elif defined(ARNIEX_SWIFITCH)
// Info
#define MANUFACTURER "ARNIEX"
#define DEVICE "SWIFITCH"
// Buttons
#define BUTTON1_PIN 4 // D2
#define BUTTON1_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON1_PRESS BUTTON_MODE_NONE
#define BUTTON1_CLICK BUTTON_MODE_TOGGLE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE
// Relays
#define RELAY1_PIN 5 // D1
#define RELAY1_TYPE RELAY_TYPE_INVERSE
// LEDs
#define LED1_PIN 12 // D6
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// ESP-01S RELAY v4.0
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180404024035&SearchText=esp-01s+relay
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ESP01SRELAY40)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ESP01S_RELAY_40"
// Relays
#define RELAY1_PIN 0
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// ESP-01S RGB LED v1.0 (some sold with ws2818)
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180404023816&SearchText=esp-01s+led+controller
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ESP01SRGBLED10)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ESP01S_RGBLED_10"
// This board is sold as RGB LED module BUT it has on board 3 pin ph2.0 connector (VCC, GPIO2, GND)
// so, if you wish, you may connect LED, BUTTON, RELAY, SENSOR etc.
// Buttons
//#define BUTTON1_PIN 2
// Relays
//#define RELAY1_PIN 2
// LEDs
#define LED1_PIN 2
// -----------------------------------------------------------------------------
// Heltec Touch Relay
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180408043114&SearchText=esp8266+touch+relay
// -----------------------------------------------------------------------------
#elif defined(HELTEC_TOUCHRELAY)
// Info
#define MANUFACTURER "HELTEC"
#define DEVICE "TOUCH_RELAY"
// Buttons
#define BUTTON1_PIN 14
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// TEST boards (do not use!!)
// -----------------------------------------------------------------------------
#elif defined(TRAVIS01)
// Info
#define MANUFACTURER "TravisCI"
#define DEVICE "Virtual board 01"
// Some buttons - pin 0
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Some relays - pin 1
#define RELAY1_PIN 1
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// Some LEDs - pin 2
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// A bit of I2C - pins 3,4
#define I2C_SDA_PIN 3
#define I2C_SCL_PIN 4
// And, as they say in "From Dusk till Dawn":
// This is a sensor blow out!
// Alright, we got white sensor, black sensor, spanish sensor, yellow sensor. We got hot sensor, cold sensor.
// We got wet sensor. We got smelly sensor. We got hairy sensor, bloody sensor. We got snapping sensor.
// We got silk sensor, velvet sensor, naugahyde sensor. We even got horse sensor, dog sensor, chicken sensor.
// C'mon, you want sensor, come on in sensor lovers!
// If we don’t got it, you don't want it!
#define BH1750_SUPPORT 1
#define BMX280_SUPPORT 1
#define SHT3X_I2C_SUPPORT 1
#define EMON_ADC121_SUPPORT 1
#define EMON_ADS1X15_SUPPORT 1
#define SHT3X_I2C_SUPPORT 1
#define SI7021_SUPPORT 1
// A bit of lights - pin 5
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define LIGHT_CHANNELS 1
#define LIGHT_CH1_PIN 5
#define LIGHT_CH1_INVERSE 0
// A bit of HLW8012 - pins 6,7,8
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 6
#define HLW8012_CF1_PIN 7
#define HLW8012_CF_PIN 8
// A bit of Dallas - pin 9
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 9
// A bit of ECH1560 - pins 10,11, 12
#ifndef ECH1560_SUPPORT
#define ECH1560_SUPPORT 1
#endif
#define ECH1560_CLK_PIN 10
#define ECH1560_MISO_PIN 11
#define ECH1560_INVERTED 12
#elif defined(TRAVIS02)
// Relay provider dual
#define MANUFACTURER "TravisCI"
#define DEVICE "Virtual board 02"
// A bit of DHT - pin 1
#ifndef DHT_SUPPORT
#define DHT_SUPPORT 1
#endif
#define DHT_PIN 1
// Relay type dual - pins 2,3
#define RELAY_PROVIDER RELAY_PROVIDER_DUAL
#define RELAY1_PIN 2
#define RELAY2_PIN 3
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// IR - pin 4
#define IR_SUPPORT 1
#define IR_PIN 4
#define IR_BUTTON_SET 1
#elif defined(TRAVIS03)
// Relay provider light/my92XX
#define MANUFACTURER "TravisCI"
#define DEVICE "Virtual board 03"
// MY9231 Light - pins 1,2
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
#define LIGHT_CHANNELS 5
#define MY92XX_MODEL MY92XX_MODEL_MY9231
#define MY92XX_CHIPS 2
#define MY92XX_DI_PIN 1
#define MY92XX_DCKI_PIN 2
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 4, 3, 5, 0, 1
#endif
// -----------------------------------------------------------------------------
// Check definitions
// -----------------------------------------------------------------------------
#if not defined(MANUFACTURER) || not defined(DEVICE)
#error "UNSUPPORTED HARDWARE!!"
#endif
Reference in New Issue View Git Blame Copy Permalink