797 lines
28 KiB
C
Executable File
797 lines
28 KiB
C
Executable File
// =============================================================================
|
|
// SENSORS - General data
|
|
// =============================================================================
|
|
|
|
#define SENSOR_DEBUG 0 // Debug sensors
|
|
|
|
#define SENSOR_READ_INTERVAL 6 // Read data from sensors every 6 seconds
|
|
#define SENSOR_READ_MIN_INTERVAL 6 // Minimum read interval
|
|
#define SENSOR_READ_MAX_INTERVAL 3600 // Maximum read interval
|
|
#define SENSOR_INIT_INTERVAL 10000 // Try to re-init non-ready sensors every 10s
|
|
|
|
#define SENSOR_REPORT_EVERY 10 // Report every this many readings
|
|
#define SENSOR_REPORT_MIN_EVERY 1 // Minimum every value
|
|
#define SENSOR_REPORT_MAX_EVERY 12 // Maximum
|
|
|
|
#define SENSOR_USE_INDEX 0 // Use the index in topic (i.e. temperature/0)
|
|
// even if just one sensor (0 for backwards compatibility)
|
|
|
|
#ifndef SENSOR_POWER_CHECK_STATUS
|
|
#define SENSOR_POWER_CHECK_STATUS 1 // If set to 1 the reported power/current/energy will be 0 if the relay[0] is OFF
|
|
#endif
|
|
|
|
#ifndef SENSOR_TEMPERATURE_CORRECTION
|
|
#define SENSOR_TEMPERATURE_CORRECTION 0.0 // Offset correction
|
|
#endif
|
|
|
|
#ifndef TEMPERATURE_MIN_CHANGE
|
|
#define TEMPERATURE_MIN_CHANGE 0.0 // Minimum temperature change to report
|
|
#endif
|
|
|
|
#ifndef SENSOR_HUMIDITY_CORRECTION
|
|
#define SENSOR_HUMIDITY_CORRECTION 0.0 // Offset correction
|
|
#endif
|
|
|
|
#ifndef HUMIDITY_MIN_CHANGE
|
|
#define HUMIDITY_MIN_CHANGE 0 // Minimum humidity change to report
|
|
#endif
|
|
|
|
// American Society of Heating, Refrigerating and Air-Conditioning Engineers suggests a range of 45% - 55% humidity to manage health effects and illnesses.
|
|
// Comfortable: 30% - 60%
|
|
// Recommended: 45% - 55%
|
|
// High : 55% - 80%
|
|
#define HUMIDITY_NORMAL 0 // > %30
|
|
#define HUMIDITY_COMFORTABLE 1 // > %45
|
|
#define HUMIDITY_DRY 2 // < %30
|
|
#define HUMIDITY_WET 3 // > %70
|
|
|
|
// United States Environmental Protection Agency - UV Index Scale
|
|
// One UV Index unit is equivalent to 25 milliWatts per square meter.
|
|
#define UV_INDEX_LOW 0 // 0 to 2 means low danger from the sun's UV rays for the average person.
|
|
#define UV_INDEX_MODERATE 1 // 3 to 5 means moderate risk of harm from unprotected sun exposure.
|
|
#define UV_INDEX_HIGH 2 // 6 to 7 means high risk of harm from unprotected sun exposure. Protection against skin and eye damage is needed.
|
|
#define UV_INDEX_VERY_HIGH 3 // 8 to 10 means very high risk of harm from unprotected sun exposure.
|
|
// Take extra precautions because unprotected skin and eyes will be damaged and can burn quickly.
|
|
#define UV_INDEX_EXTREME 4 // 11 or more means extreme risk of harm from unprotected sun exposure.
|
|
// Take all precautions because unprotected skin and eyes can burn in minutes.
|
|
|
|
#define SENSOR_PUBLISH_ADDRESSES 0 // Publish sensor addresses
|
|
#define SENSOR_ADDRESS_TOPIC "address" // Topic to publish sensor addresses
|
|
|
|
//------------------------------------------------------------------------------
|
|
// UNITS
|
|
//------------------------------------------------------------------------------
|
|
|
|
#define POWER_WATTS 0
|
|
#define POWER_KILOWATTS 1
|
|
|
|
#define ENERGY_JOULES 0
|
|
#define ENERGY_KWH 1
|
|
|
|
#define TMP_CELSIUS 0
|
|
#define TMP_FAHRENHEIT 1
|
|
|
|
#ifndef SENSOR_TEMPERATURE_UNITS
|
|
#define SENSOR_TEMPERATURE_UNITS TMP_CELSIUS // Temperature units (TMP_CELSIUS | TMP_FAHRENHEIT)
|
|
#endif
|
|
|
|
#ifndef SENSOR_ENERGY_UNITS
|
|
#define SENSOR_ENERGY_UNITS ENERGY_JOULES // Energy units (ENERGY_JOULES | ENERGY_KWH)
|
|
#endif
|
|
|
|
#ifndef SENSOR_POWER_UNITS
|
|
#define SENSOR_POWER_UNITS POWER_WATTS // Power units (POWER_WATTS | POWER_KILOWATTS)
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Sensor ID
|
|
// These should remain over time, do not modify them, only add new ones at the end
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#define SENSOR_DHTXX_ID 0x01
|
|
#define SENSOR_DALLAS_ID 0x02
|
|
#define SENSOR_EMON_ANALOG_ID 0x03
|
|
#define SENSOR_EMON_ADC121_ID 0x04
|
|
#define SENSOR_EMON_ADS1X15_ID 0x05
|
|
#define SENSOR_HLW8012_ID 0x06
|
|
#define SENSOR_V9261F_ID 0x07
|
|
#define SENSOR_ECH1560_ID 0x08
|
|
#define SENSOR_ANALOG_ID 0x09
|
|
#define SENSOR_DIGITAL_ID 0x10
|
|
#define SENSOR_EVENTS_ID 0x11
|
|
#define SENSOR_PMSX003_ID 0x12
|
|
#define SENSOR_BMX280_ID 0x13
|
|
#define SENSOR_MHZ19_ID 0x14
|
|
#define SENSOR_SI7021_ID 0x15
|
|
#define SENSOR_SHT3X_I2C_ID 0x16
|
|
#define SENSOR_BH1750_ID 0x17
|
|
#define SENSOR_PZEM004T_ID 0x18
|
|
#define SENSOR_AM2320_ID 0x19
|
|
#define SENSOR_GUVAS12SD_ID 0x20
|
|
#define SENSOR_CSE7766_ID 0x21
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Magnitudes
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#define MAGNITUDE_NONE 0
|
|
#define MAGNITUDE_TEMPERATURE 1
|
|
#define MAGNITUDE_HUMIDITY 2
|
|
#define MAGNITUDE_PRESSURE 3
|
|
#define MAGNITUDE_CURRENT 4
|
|
#define MAGNITUDE_VOLTAGE 5
|
|
#define MAGNITUDE_POWER_ACTIVE 6
|
|
#define MAGNITUDE_POWER_APPARENT 7
|
|
#define MAGNITUDE_POWER_REACTIVE 8
|
|
#define MAGNITUDE_POWER_FACTOR 9
|
|
#define MAGNITUDE_ENERGY 10
|
|
#define MAGNITUDE_ENERGY_DELTA 11
|
|
#define MAGNITUDE_ANALOG 12
|
|
#define MAGNITUDE_DIGITAL 13
|
|
#define MAGNITUDE_EVENTS 14
|
|
#define MAGNITUDE_PM1dot0 15
|
|
#define MAGNITUDE_PM2dot5 16
|
|
#define MAGNITUDE_PM10 17
|
|
#define MAGNITUDE_CO2 18
|
|
#define MAGNITUDE_LUX 19
|
|
#define MAGNITUDE_UV 20
|
|
|
|
#define MAGNITUDE_MAX 21
|
|
|
|
// =============================================================================
|
|
// Specific data for each sensor
|
|
// =============================================================================
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Analog sensor
|
|
// Enable support by passing ANALOG_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef ANALOG_SUPPORT
|
|
#define ANALOG_SUPPORT 0
|
|
#endif
|
|
|
|
#if ANALOG_SUPPORT
|
|
#undef ADC_VCC_ENABLED
|
|
#define ADC_VCC_ENABLED 0
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// BH1750
|
|
// Enable support by passing BH1750_SUPPORT=1 build flag
|
|
// http://www.elechouse.com/elechouse/images/product/Digital%20light%20Sensor/bh1750fvi-e.pdf
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef BH1750_SUPPORT
|
|
#define BH1750_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef BH1750_ADDRESS
|
|
#define BH1750_ADDRESS 0x00 // 0x00 means auto
|
|
#endif
|
|
|
|
#define BH1750_MODE BH1750_CONTINUOUS_HIGH_RES_MODE
|
|
|
|
#if BH1750_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// BME280/BMP280
|
|
// Enable support by passing BMX280_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef BMX280_SUPPORT
|
|
#define BMX280_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef BMX280_ADDRESS
|
|
#define BMX280_ADDRESS 0x00 // 0x00 means auto
|
|
#endif
|
|
|
|
#define BMX280_MODE 1 // 0 for sleep mode, 1 or 2 for forced mode, 3 for normal mode
|
|
#define BMX280_STANDBY 0 // 0 for 0.5ms, 1 for 62.5ms, 2 for 125ms
|
|
// 3 for 250ms, 4 for 500ms, 5 for 1000ms
|
|
// 6 for 10ms, 7 for 20ms
|
|
#define BMX280_FILTER 0 // 0 for OFF, 1 for 2 values, 2 for 4 values, 3 for 8 values and 4 for 16 values
|
|
#define BMX280_TEMPERATURE 1 // Oversampling for temperature (set to 0 to disable magnitude)
|
|
#define BMX280_HUMIDITY 1 // Oversampling for humidity (set to 0 to disable magnitude, only for BME280)
|
|
#define BMX280_PRESSURE 1 // Oversampling for pressure (set to 0 to disable magnitude)
|
|
|
|
#if BMX280_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Dallas OneWire temperature sensors
|
|
// Enable support by passing DALLAS_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef DALLAS_SUPPORT
|
|
#define DALLAS_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef DALLAS_PIN
|
|
#define DALLAS_PIN 14
|
|
#endif
|
|
|
|
#define DALLAS_RESOLUTION 9 // Not used atm
|
|
#define DALLAS_READ_INTERVAL 2000 // Force sensor read & cache every 2 seconds
|
|
|
|
//------------------------------------------------------------------------------
|
|
// DHTXX temperature/humidity sensor
|
|
// Enable support by passing DHT_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef DHT_SUPPORT
|
|
#define DHT_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef DHT_PIN
|
|
#define DHT_PIN 13
|
|
#endif
|
|
|
|
#ifndef DHT_TYPE
|
|
#define DHT_TYPE DHT_CHIP_DHT22
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// CSE7766 based power sensor
|
|
// Enable support by passing CSE7766_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef CSE7766_SUPPORT
|
|
#define CSE7766_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef CSE7766_PIN
|
|
#define CSE7766_PIN 1 // TX pin from the CSE7766
|
|
#endif
|
|
|
|
#ifndef CSE7766_PIN_INVERSE
|
|
#define CSE7766_PIN_INVERSE 0 // Signal is inverted
|
|
#endif
|
|
|
|
#define CSE7766_SYNC_INTERVAL 300 // Safe time between transmissions (ms)
|
|
#define CSE7766_BAUDRATE 4800 // UART baudrate
|
|
|
|
#define CSE7766_V1R 1.0 // 1mR current resistor
|
|
#define CSE7766_V2R 1.0 // 1M voltage resistor
|
|
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Digital sensor
|
|
// Enable support by passing DIGITAL_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef DIGITAL_SUPPORT
|
|
#define DIGITAL_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef DIGITAL_PIN
|
|
#define DIGITAL_PIN 2
|
|
#endif
|
|
|
|
#ifndef DIGITAL_PIN_MODE
|
|
#define DIGITAL_PIN_MODE INPUT_PULLUP
|
|
#endif
|
|
|
|
#ifndef DIGITAL_DEFAULT_STATE
|
|
#define DIGITAL_DEFAULT_STATE 1
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// ECH1560 based power sensor
|
|
// Enable support by passing ECH1560_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef ECH1560_SUPPORT
|
|
#define ECH1560_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef ECH1560_CLK_PIN
|
|
#define ECH1560_CLK_PIN 4 // CLK pin for the ECH1560
|
|
#endif
|
|
|
|
#ifndef ECH1560_MISO_PIN
|
|
#define ECH1560_MISO_PIN 5 // MISO pin for the ECH1560
|
|
#endif
|
|
|
|
#ifndef ECH1560_INVERTED
|
|
#define ECH1560_INVERTED 0 // Signal is inverted
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Energy Monitor general settings
|
|
//------------------------------------------------------------------------------
|
|
|
|
#define EMON_MAX_SAMPLES 1000 // Max number of samples to get
|
|
#define EMON_MAX_TIME 250 // Max time in ms to sample
|
|
#define EMON_FILTER_SPEED 512 // Mobile average filter speed
|
|
#define EMON_MAINS_VOLTAGE 230 // Mains voltage
|
|
#define EMON_REFERENCE_VOLTAGE 3.3 // Reference voltage of the ADC
|
|
#define EMON_CURRENT_RATIO 30 // Current ratio in the clamp (30V/1A)
|
|
#define EMON_REPORT_CURRENT 0 // Report current
|
|
#define EMON_REPORT_POWER 1 // Report power
|
|
#define EMON_REPORT_ENERGY 1 // Report energy
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Energy Monitor based on ADC121
|
|
// Enable support by passing EMON_ADC121_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef EMON_ADC121_SUPPORT
|
|
#define EMON_ADC121_SUPPORT 0 // Do not build support by default
|
|
#endif
|
|
|
|
#define EMON_ADC121_I2C_ADDRESS 0x00 // 0x00 means auto
|
|
|
|
#if EMON_ADC121_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Energy Monitor based on ADS1X15
|
|
// Enable support by passing EMON_ADS1X15_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef EMON_ADS1X15_SUPPORT
|
|
#define EMON_ADS1X15_SUPPORT 0 // Do not build support by default
|
|
#endif
|
|
|
|
#define EMON_ADS1X15_I2C_ADDRESS 0x00 // 0x00 means auto
|
|
#define EMON_ADS1X15_TYPE ADS1X15_CHIP_ADS1115
|
|
#define EMON_ADS1X15_GAIN ADS1X15_REG_CONFIG_PGA_4_096V
|
|
#define EMON_ADS1X15_MASK 0x0F // A0=1 A1=2 A2=4 A3=8
|
|
|
|
#if EMON_ADS1X15_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Energy Monitor based on interval analog GPIO
|
|
// Enable support by passing EMON_ANALOG_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef EMON_ANALOG_SUPPORT
|
|
#define EMON_ANALOG_SUPPORT 0 // Do not build support by default
|
|
#endif
|
|
|
|
#if EMON_ANALOG_SUPPORT
|
|
#undef ADC_VCC_ENABLED
|
|
#define ADC_VCC_ENABLED 0
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Counter sensor
|
|
// Enable support by passing EVENTS_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef EVENTS_SUPPORT
|
|
#define EVENTS_SUPPORT 0 // Do not build with counter support by default
|
|
#endif
|
|
|
|
#ifndef EVENTS_PIN
|
|
#define EVENTS_PIN 2 // GPIO to monitor
|
|
#endif
|
|
|
|
#ifndef EVENTS_PIN_MODE
|
|
#define EVENTS_PIN_MODE INPUT // INPUT, INPUT_PULLUP
|
|
#endif
|
|
|
|
#ifndef EVENTS_INTERRUPT_MODE
|
|
#define EVENTS_INTERRUPT_MODE RISING // RISING, FALLING, BOTH
|
|
#endif
|
|
|
|
#define EVENTS_DEBOUNCE 50 // Do not register events within less than 10 millis
|
|
|
|
//------------------------------------------------------------------------------
|
|
// HLW8012 Energy monitor IC
|
|
// Enable support by passing HLW8012_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef HLW8012_SUPPORT
|
|
#define HLW8012_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef HLW8012_SEL_PIN
|
|
#define HLW8012_SEL_PIN 5
|
|
#endif
|
|
|
|
#ifndef HLW8012_CF1_PIN
|
|
#define HLW8012_CF1_PIN 13
|
|
#endif
|
|
|
|
#ifndef HLW8012_CF_PIN
|
|
#define HLW8012_CF_PIN 14
|
|
#endif
|
|
|
|
#ifndef HLW8012_SEL_CURRENT
|
|
#define HLW8012_SEL_CURRENT HIGH // SEL pin to HIGH to measure current
|
|
#endif
|
|
|
|
#ifndef HLW8012_CURRENT_R
|
|
#define HLW8012_CURRENT_R 0.001 // Current resistor
|
|
#endif
|
|
|
|
#ifndef HLW8012_VOLTAGE_R_UP
|
|
#define HLW8012_VOLTAGE_R_UP ( 5 * 470000 ) // Upstream voltage resistor
|
|
#endif
|
|
|
|
#ifndef HLW8012_VOLTAGE_R_DOWN
|
|
#define HLW8012_VOLTAGE_R_DOWN ( 1000 ) // Downstream voltage resistor
|
|
#endif
|
|
|
|
#define HLW8012_USE_INTERRUPTS 1 // Use interrupts to trap HLW8012 signals
|
|
|
|
//------------------------------------------------------------------------------
|
|
// MHZ19 CO2 sensor
|
|
// Enable support by passing MHZ19_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef MHZ19_SUPPORT
|
|
#define MHZ19_SUPPORT 0
|
|
#endif
|
|
|
|
#define MHZ19_RX_PIN 13
|
|
#define MHZ19_TX_PIN 15
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Particle Monitor based on Plantower PMSX003
|
|
// Enable support by passing PMSX003_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef PMSX003_SUPPORT
|
|
#define PMSX003_SUPPORT 0
|
|
#endif
|
|
|
|
#define PMS_RX_PIN 13
|
|
#define PMS_TX_PIN 15
|
|
|
|
//------------------------------------------------------------------------------
|
|
// PZEM004T based power monitor
|
|
// Enable support by passing PZEM004T_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef PZEM004T_SUPPORT
|
|
#define PZEM004T_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef PZEM004T_USE_SOFT
|
|
#define PZEM004T_USE_SOFT 1 // Use software serial
|
|
#endif
|
|
|
|
#ifndef PZEM004T_RX_PIN
|
|
#define PZEM004T_RX_PIN 13 // Software serial RX GPIO (if PZEM004T_USE_SOFT == 1)
|
|
#endif
|
|
|
|
#ifndef PZEM004T_TX_PIN
|
|
#define PZEM004T_TX_PIN 15 // Software serial TX GPIO (if PZEM004T_USE_SOFT == 1)
|
|
#endif
|
|
|
|
#ifndef PZEM004T_HW_PORT
|
|
#define PZEM004T_HW_PORT Serial1 // Hardware serial port (if PZEM004T_USE_SOFT == 0)
|
|
#endif
|
|
|
|
|
|
//------------------------------------------------------------------------------
|
|
// SHT3X I2C (Wemos) temperature & humidity sensor
|
|
// Enable support by passing SHT3X_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef SHT3X_I2C_SUPPORT
|
|
#define SHT3X_I2C_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef SHT3X_I2C_ADDRESS
|
|
#define SHT3X_I2C_ADDRESS 0x00 // 0x00 means auto
|
|
#endif
|
|
|
|
#if SHT3X_I2C_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// SI7021 temperature & humidity sensor
|
|
// Enable support by passing SI7021_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef SI7021_SUPPORT
|
|
#define SI7021_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef SI7021_ADDRESS
|
|
#define SI7021_ADDRESS 0x00 // 0x00 means auto
|
|
#endif
|
|
|
|
#if SI7021_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// V9261F based power sensor
|
|
// Enable support by passing SI7021_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef V9261F_SUPPORT
|
|
#define V9261F_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef V9261F_PIN
|
|
#define V9261F_PIN 2 // TX pin from the V9261F
|
|
#endif
|
|
|
|
#ifndef V9261F_PIN_INVERSE
|
|
#define V9261F_PIN_INVERSE 1 // Signal is inverted
|
|
#endif
|
|
|
|
#define V9261F_SYNC_INTERVAL 600 // Sync signal length (ms)
|
|
#define V9261F_BAUDRATE 4800 // UART baudrate
|
|
|
|
// Default ratios
|
|
#define V9261F_CURRENT_FACTOR 79371434.0
|
|
#define V9261F_VOLTAGE_FACTOR 4160651.0
|
|
#define V9261F_POWER_FACTOR 153699.0
|
|
#define V9261F_RPOWER_FACTOR V9261F_CURRENT_FACTOR
|
|
|
|
//------------------------------------------------------------------------------
|
|
// AM2320 Humidity & Temperature sensor over I2C
|
|
// Enable support by passing AM2320_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef AM2320_SUPPORT
|
|
#define AM2320_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef AM2320_ADDRESS
|
|
#define AM2320_ADDRESS 0x00 // 0x00 means auto
|
|
#endif
|
|
|
|
#if AM2320_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// GUVAS12SD UV Sensor (analog)
|
|
// Enable support by passing GUVAS12SD_SUPPORT=1 build flag
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef GUVAS12SD_SUPPORT
|
|
#define GUVAS12SD_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef GUVAS12SD_PIN
|
|
#define GUVAS12SD_PIN 14
|
|
#endif
|
|
|
|
// =============================================================================
|
|
// Sensor helpers configuration
|
|
// =============================================================================
|
|
|
|
#ifndef SENSOR_SUPPORT
|
|
#if ANALOG_SUPPORT || BH1750_SUPPORT || BMX280_SUPPORT || DALLAS_SUPPORT \
|
|
|| DHT_SUPPORT || DIGITAL_SUPPORT || ECH1560_SUPPORT \
|
|
|| EMON_ADC121_SUPPORT || EMON_ADS1X15_SUPPORT \
|
|
|| EMON_ANALOG_SUPPORT || EVENTS_SUPPORT || HLW8012_SUPPORT \
|
|
|| MHZ19_SUPPORT || PMSX003_SUPPORT || SHT3X_I2C_SUPPORT \
|
|
|| SI7021_SUPPORT || V9261F_SUPPORT || AM2320_SUPPORT \
|
|
|| GUVAS12SD_SUPPORT || CSE7766_SUPPORT
|
|
#define SENSOR_SUPPORT 1
|
|
#else
|
|
#define SENSOR_SUPPORT 0
|
|
#endif
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// I2C
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef I2C_SUPPORT
|
|
#define I2C_SUPPORT 0 // I2C enabled (1.98Kb)
|
|
#endif
|
|
|
|
#define I2C_USE_BRZO 0 // Use brzo_i2c library or standard Wire
|
|
|
|
#ifndef I2C_SDA_PIN
|
|
#define I2C_SDA_PIN SDA // SDA GPIO (Sonoff => 4)
|
|
#endif
|
|
|
|
#ifndef I2C_SCL_PIN
|
|
#define I2C_SCL_PIN SCL // SCL GPIO (Sonoff => 14)
|
|
#endif
|
|
|
|
#define I2C_CLOCK_STRETCH_TIME 200 // BRZO clock stretch time
|
|
#define I2C_SCL_FREQUENCY 1000 // BRZO SCL frequency
|
|
#define I2C_CLEAR_BUS 0 // Clear I2C bus on boot
|
|
#define I2C_PERFORM_SCAN 1 // Perform a bus scan on boot
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Internal power monitor
|
|
// Enable support by passing ADC_VCC_ENABLED=1 build flag
|
|
// Do not enable this if using the analog GPIO for any other thing
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef ADC_VCC_ENABLED
|
|
#define ADC_VCC_ENABLED 1
|
|
#endif
|
|
|
|
#if ADC_VCC_ENABLED
|
|
ADC_MODE(ADC_VCC);
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Class loading
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#if SENSOR_SUPPORT
|
|
|
|
PROGMEM const unsigned char magnitude_decimals[] = {
|
|
0,
|
|
1, 0, 2,
|
|
3, 0, 0, 0, 0, 0, 0, 0,
|
|
0, 0, 0,
|
|
0, 0, 0,
|
|
0, 0
|
|
};
|
|
|
|
PROGMEM const char magnitude_unknown_topic[] = "unknown";
|
|
PROGMEM const char magnitude_temperature_topic[] = "temperature";
|
|
PROGMEM const char magnitude_humidity_topic[] = "humidity";
|
|
PROGMEM const char magnitude_pressure_topic[] = "pressure";
|
|
PROGMEM const char magnitude_current_topic[] = "current";
|
|
PROGMEM const char magnitude_voltage_topic[] = "voltage";
|
|
PROGMEM const char magnitude_active_power_topic[] = "power";
|
|
PROGMEM const char magnitude_apparent_power_topic[] = "apparent";
|
|
PROGMEM const char magnitude_reactive_power_topic[] = "reactive";
|
|
PROGMEM const char magnitude_power_factor_topic[] = "factor";
|
|
PROGMEM const char magnitude_energy_topic[] = "energy";
|
|
PROGMEM const char magnitude_energy_delta_topic[] = "energy_delta";
|
|
PROGMEM const char magnitude_analog_topic[] = "analog";
|
|
PROGMEM const char magnitude_digital_topic[] = "digital";
|
|
PROGMEM const char magnitude_events_topic[] = "events";
|
|
PROGMEM const char magnitude_pm1dot0_topic[] = "pm1dot0";
|
|
PROGMEM const char magnitude_pm2dot5_topic[] = "pm2dot5";
|
|
PROGMEM const char magnitude_pm10_topic[] = "pm10";
|
|
PROGMEM const char magnitude_co2_topic[] = "co2";
|
|
PROGMEM const char magnitude_lux_topic[] = "lux";
|
|
PROGMEM const char magnitude_uv_topic[] = "uv";
|
|
|
|
PROGMEM const char* const magnitude_topics[] = {
|
|
magnitude_unknown_topic, magnitude_temperature_topic, magnitude_humidity_topic,
|
|
magnitude_pressure_topic, magnitude_current_topic, magnitude_voltage_topic,
|
|
magnitude_active_power_topic, magnitude_apparent_power_topic, magnitude_reactive_power_topic,
|
|
magnitude_power_factor_topic, magnitude_energy_topic, magnitude_energy_delta_topic,
|
|
magnitude_analog_topic, magnitude_digital_topic, magnitude_events_topic,
|
|
magnitude_pm1dot0_topic, magnitude_pm2dot5_topic, magnitude_pm10_topic,
|
|
magnitude_co2_topic, magnitude_lux_topic, magnitude_uv_topic
|
|
};
|
|
|
|
PROGMEM const char magnitude_empty[] = "";
|
|
PROGMEM const char magnitude_celsius[] = "C";
|
|
PROGMEM const char magnitude_fahrenheit[] = "F";
|
|
PROGMEM const char magnitude_percentage[] = "%";
|
|
PROGMEM const char magnitude_hectopascals[] = "hPa";
|
|
PROGMEM const char magnitude_amperes[] = "A";
|
|
PROGMEM const char magnitude_volts[] = "V";
|
|
PROGMEM const char magnitude_watts[] = "W";
|
|
PROGMEM const char magnitude_kw[] = "kW";
|
|
PROGMEM const char magnitude_joules[] = "J";
|
|
PROGMEM const char magnitude_kwh[] = "kWh";
|
|
PROGMEM const char magnitude_ugm3[] = "µg/m3";
|
|
PROGMEM const char magnitude_ppm[] = "ppm";
|
|
PROGMEM const char magnitude_lux[] = "lux";
|
|
PROGMEM const char magnitude_uv[] = "uv";
|
|
|
|
PROGMEM const char* const magnitude_units[] = {
|
|
magnitude_empty, magnitude_celsius, magnitude_percentage,
|
|
magnitude_hectopascals, magnitude_amperes, magnitude_volts,
|
|
magnitude_watts, magnitude_watts, magnitude_watts,
|
|
magnitude_percentage, magnitude_joules, magnitude_joules,
|
|
magnitude_empty, magnitude_empty, magnitude_empty,
|
|
magnitude_ugm3, magnitude_ugm3, magnitude_ugm3,
|
|
magnitude_ppm, magnitude_lux, magnitude_uv
|
|
};
|
|
|
|
#include "../sensors/BaseSensor.h"
|
|
|
|
#if ANALOG_SUPPORT
|
|
#include "../sensors/AnalogSensor.h"
|
|
#endif
|
|
|
|
#if BH1750_SUPPORT
|
|
#include "../sensors/BH1750Sensor.h"
|
|
#endif
|
|
|
|
#if BMX280_SUPPORT
|
|
#include "../sensors/BMX280Sensor.h"
|
|
#endif
|
|
|
|
#if CSE7766_SUPPORT
|
|
#include <SoftwareSerial.h>
|
|
#include "../sensors/CSE7766Sensor.h"
|
|
#endif
|
|
|
|
#if DALLAS_SUPPORT
|
|
#include <OneWire.h>
|
|
#include "../sensors/DallasSensor.h"
|
|
#endif
|
|
|
|
#if DHT_SUPPORT
|
|
#include "../sensors/DHTSensor.h"
|
|
#endif
|
|
|
|
#if DIGITAL_SUPPORT
|
|
#include "../sensors/DigitalSensor.h"
|
|
#endif
|
|
|
|
#if ECH1560_SUPPORT
|
|
#include "../sensors/ECH1560Sensor.h"
|
|
#endif
|
|
|
|
#if EMON_ADC121_SUPPORT
|
|
#include "../sensors/EmonADC121Sensor.h"
|
|
#endif
|
|
|
|
#if EMON_ADS1X15_SUPPORT
|
|
#include "../sensors/EmonADS1X15Sensor.h"
|
|
#endif
|
|
|
|
#if EMON_ANALOG_SUPPORT
|
|
#include "../sensors/EmonAnalogSensor.h"
|
|
#endif
|
|
|
|
#if EVENTS_SUPPORT
|
|
#include "../sensors/EventSensor.h"
|
|
#endif
|
|
|
|
#if HLW8012_SUPPORT
|
|
#include <HLW8012.h>
|
|
#include "../sensors/HLW8012Sensor.h"
|
|
#endif
|
|
|
|
#if MHZ19_SUPPORT
|
|
#include <SoftwareSerial.h>
|
|
#include "../sensors/MHZ19Sensor.h"
|
|
#endif
|
|
|
|
#if PMSX003_SUPPORT
|
|
#include <SoftwareSerial.h>
|
|
#include <PMS.h>
|
|
#include "../sensors/PMSX003Sensor.h"
|
|
#endif
|
|
|
|
#if PZEM004T_SUPPORT
|
|
#include <SoftwareSerial.h>
|
|
#include "../sensors/PZEM004TSensor.h"
|
|
#endif
|
|
|
|
#if SI7021_SUPPORT
|
|
#include "../sensors/SI7021Sensor.h"
|
|
#endif
|
|
|
|
#if SHT3X_I2C_SUPPORT
|
|
#include "../sensors/SHT3XI2CSensor.h"
|
|
#endif
|
|
|
|
#if V9261F_SUPPORT
|
|
#include <SoftwareSerial.h>
|
|
#include "../sensors/V9261FSensor.h"
|
|
#endif
|
|
|
|
#if AM2320_SUPPORT
|
|
#include "../sensors/AM2320Sensor.h"
|
|
#endif
|
|
|
|
#if GUVAS12SD_SUPPORT
|
|
#include "../sensors/GUVAS12SDSensor.h"
|
|
#endif
|
|
|
|
#endif // SENSOR_SUPPORT
|